Search Documents

By Poi G, Madgwick J. C, Davis P, Pannowitz D, Cho D, MacKay B, Chan S. M, Varga R. A, Chun U

Periodic dilute sulphuric acid treatment ofstill, batch-fed, molassesenriched, microaerobic, manganese-dioxide-Ieaching microbial cultures led to marked improvements over untreated cultures. Percentage Mn++ recoveries increased (7X), rate of Mn++ formation improved (3X) and yields of Mn++ per molasses use were more economical (5 X). The yield in terms of molasses used improved with decreasing sugar used (eg 1.17 g Mn++/gram molasses at 0.2 per cent molasses (w/v) feed and 24 per cent (w/v) pulp density MnO2 tailings). The most effective Mn++ leaching in terms ofpercentage recovery (97 per cent) and rate ofleaching (46 mg Mn++/day) was at 0.5 per cent molasses (w/v) and 14 per cent pulp density (w/v) MnO2 tailings.

Jan 1, 1986

By Creasey J. W, Huntington J. F

Faults cutting the Lithgow and Katoomba seams in some collieries of the Western Coalfield can be classified, on the basis of spatial pattern, into three principal groups: meridional swarms of closely spaced minor faults and associated joints, with throws of less than 0.5 m and with exceptional faults of up to 5 m; isolated interswarm strike-slip faults in the Lithgow seam and widely spaced strike-slip faults in swarms in the Katoomba seam; and low-angle normal faults associated with the Lidsdale-Lithgow seam split.Orientations of faults and coal cleats in the coalfield are presented on stereoplots and histograms, as a basis for an analysis of fault dynamics. The low-angle normal faults were found to have been formed only along the Lidsdale-Lithgow seam split, and before the high-angle faults. The origin of the high-angle normal faults in the meridional swarms is discussed and it is suggested that basementcover interactions must have occurred. This suggestion is supported by geophysical evidence. Low-amplitude monoclines in the coal seam, and the spacing of swarms 0.9 to 4.5 km apart, may be due to the underlying basement structure.It is clear that postextensional compressive deformation of swarms in the coalfield gave rise to shortening by minor thrust development, and probably also caused the synchronous strike-slip movement on pre-existing normal faults. There is evidence to show that isolated interswarm strike-slip faults in the Lithgow seam, and widely spaced strike-slip faults in the Katoomba seam, may have originated synchronously with such thrusts. The axis of maximum principal compression ('71) for the thrust event was inferred to be near horizontal and aligned approximately E-W. Recent rock mechanics measurements of the present day stress field indicate a similar stress configuration.

Jan 1, 1981

By H Wen

LongWangGou coalmine auxiliary inclined shaft heading face has a large section, fast heading speed, and large dust production. The problems of high concentration and wide distribution of dust in the roadway air are very prominent. To improve the efficiency of roadway ventilation and dustremoval, long-compression and short-suction (after this referred to as LCSS) are adopted. The dust concentration and airflow field distribution in the roadway are numerically simulated by FLUENT. The change of the position between the pressure duct and the exhaust duct and the different pressure-extraction ratios affect the distribution of airflow velocity, the formation of vortex zone, and the distribution of dust concentration in the roadway. When Ly = 25 m, Lc = 5.0 m, W = 1.2, a wind curtain is formed at 5 m in front of the heading face to prevent dust from spreading deeper into the roadway.

Oct 12, 2022

In a modern economy there is a compelling case why governments should not own property rights to mineral deposits. Assuming they do, however, governments will use these constitutional rights to raise revenue. They have two basic instruments to achieve this; a royalty charge on price or a rent tax on income/profits. On the one hand, a royalty charge creates a 'deadweight loss' to society by increasing cut-off grades and decreasing the life-of-mine. They are also regressive. However, they are easy to administer. On the other hand, a rent tax avoids the problem of 'deadweight loss'; it does not impact on the life-of-mine because the tax structure is neutral. But, they are difficult to administer correctly, particularly in the determination of rents and the definition of mining per se. If rents are incorrectly determined capital markets are distorted. And, if mining activities are incorrectly defined, downstream activities could be adversely affected.

Jun 1, 2010

Iron Concentrate Synthesised from Waste Ferrous Sulfate Produced in Titanium White Preparation

Sep 13, 2010

Slime Flotation Using Ethoxylated Surfactants in Solutions of the Electrolytes

Sep 13, 2010

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopic techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relating their inherent properties to properties such as volatile-matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used commercially.

Jan 1, 1970

The phenomena of nature cannot present themselves to any thinking wild without claiming from it some solution. The earth, as it has often been observed, is laid out like a well ordered cabinet, presenting to us, in measure, some means of judging how the laws of nature and the essential properties of matter have worked out all we see before us. "That there have been depositions of strata gradually laid down aud stocked with the remains of the living objects, vegetable and animal, that flourished when they were being imposed, is an universally acknowledged fact. It speaks of a constantly maintained series of operations whereby the globe has been brought to its present condition, and which are ever advancing it to stages that are still before it. That immeasurable ages have been consumed in effecting these developments is also conceded. We witness the very graduated rate of the existing advances and can see that the past action must have been conducted in the same slow deliberate manner. There are many questions, however, upon which inquirers are not agreed, hence they are still within the domains of fair discussion.What has led to those great climatic changes whereby the same portions of the earth have had at various times climates that were glacial, temperate, and tropical? What causes the constant contortions and dislocations of strata and the upheaval and depression of land levels, and that there is a tendency to alternation in the parallel areas undergoing opposite kinds of movement as if the sinking of one area balanced the rIsing of another? What is the reason that the centres of volcanic action are continually shifting, and that the line of greatest activity is always upon the rising areas? That portions of the earth have been subjected to intense alid long continued volcanic action, and again to long periods of repose, and that the periods of activity and repose are·recurrent at long intervals of time? What the mountain chains of the world are in broadly parallel bands? What has caused the stratified rocks to be tilted from their original?

By R Tweedie

'The politics of mining in New Zealand' is a topic I chose myself because of its importance in the future of the New Zealand mining industry. There are many people in the industry who are cynical about politics, cynical about politicians and definitely cynical and often critical of political decisions. In fact, many industry people say they don't want to get involved in politics, they just want to get on with the business of exploration or mining. The point of my address is that politics is important and the industry cannot afford not to participate in the political process.

Jan 1, 1991

Background geochemistry of streams in mineralised terranes is affected by (a) natural sulphide oxidation and associated metallic discharges; and (b) previous mining history and associated discharges. Both of these processes elevate background metal concentrations by (i) directly adding dissolved metals to stream water; and (ii) adding sulphide-bearing sediments' to the stream system, to be trapped in old channels and bars for later chemical decomposition in situ or after flood reworking. Definition of downstream geochemical background, involving sediments and low-flow dissolved chemistry prior to mining is prudent, as this will provide a benchmark for any required estimation of new inputs from, for example, accidental tailings discharges. Two high-profile examples from western USA illustrate these points. Summitville mine in southern Colorado is an environmental disaster left when the operating company went bankrupt in 1991. Acid metal-rich discharges are leaving the site into a river system used for agricultural irrigation. However, nearby sub-catchments have substantial naturally occurring acid metal-rich discharges and locally discharge natural sulphide-rich debris flows into the same river. Distinction between natural and anthropogenic pollution in the downstream reaches is difficult. Early mining at Cooke City, Montana (New World District) released large volumes of sulphide-bearing tailings into the river system when a tailings impoundment dam failed. The event was equivalent to a 100-year flood, and tailings were deposited for 30 km downstream. These tailings are currently oxidising, and are being reworked into the modem stream during high flow events, thus perturbing background geochemistry.

Jan 1, 1999

Geochemical projects in progress or recently completed in the Bureau of Mineral Resources, Geology, and Geophysics (BMR) cover a wide range of topics and include research projects, regional studies, and prospecting programmes. However, in these notes emphasis is given to projects which are directly relevant to mineral exploration.FIELD INVESTIGATIONSStream sediment sampling, rock and soil sampling, and geobotanical surveys have been used by the BMR in a number of areas, partly in attempts to locate specific zones of mineralization, and partly to investigate the effectiveness of the various methods under different conditions of climate and topopraphy and in different geological settings.Stream sediment sampling has been most successful in the Territory of Papua and New Guinea. For example, in the South Sepik area, zones of disseminated su1phide mineralisation were found to give rise to anomalies with peak values of up to 1,000 p.p.m. copper, compared with background values of about 40 p.p.m. (Dow et al., 1968). By contrast, the results of rather limited work in the Northern Territory and in the Kimberley district of Westen Australia were inconclusive.Rock and soil sampling, on the other hand, was successfully used in a number of areas in Northern Australia, particularly at Rum Jungle and Tennant Creek.Rum Jungle area In the Rum Jungle area, where uranium and base metal mineralization is mainly associated with a Lower Proterozoic black slate sequence, samples, of c-horizon soil or weathered 'rock are generally collectedfrom the bottom of drill holes, usually 15 to 20 ft deep, bored with a power-operated auger.Surface sampling indicates that such a technique would probably have shown up all the major geochemical anomalies delineated by deep sampling, but the latter gives slightly more consistent and slightly

Jan 1, 1970

Copper Recovery from Printed Circuit Board by Carbonisation

Sep 13, 2010

By M P. Simpson

Forty one whole rock samples from the Gold Cross low-sulfidation epithermal Au-Ag deposit have d18O values that range from 4.4 to 9.3 per mil, with an average value of 7.0 per mil. Unaltered and weakly altered rocks have d18O values greater than eight per mil, and the orebody is surrounded by samples that are depleted in 18O. A strongly silicified sample adjacent to the Empire Vein System has a d18O value of 9.0 per mil, similar to previously reported analyses of vein quartz (7.0 to 11.7ë, average 9.4ë). This suggests that, in detail, Golden Cross may have a zone of 18O-enriched wall rocks in the core of the deposit, adjacent to the main underground veins. Although some workers have suggested that stable isotope geochemistry may provide useful information for epithermal mineral deposit exploration, at Golden Cross this is not the case. Alteration minerals, major elements and trace elements all define larger, less ambiguous halos than the zone of 18O-depleted wall rocks.

Jan 1, 2001

By W. J. LANGRON

This paper describes the results of VLF-EM test surveys, using the Ronka EM-16 equipment, over a selection of environments in Australia and Papua.Using comparisons with known geology, drilling information and other geophysical work it is shown that the maximum depth of penetration of the method is about 100 ft but is considerably less than this in most areas.The author believes the method could aid in geological mapping and provide a useful adjunct to aeromagnetic surveying in some areas.

Jan 1, 1972

By C De-Vitry

"The large Yandi channel iron deposit (CID) is located in the north-west of Western Australia and is currently mined via open pit methods. Drilling at Yandi is widely spaced and current estimates are mostly linear averages of the surrounding local samples. Linear estimates such as ordinary kriging (OK) based on block sizes that are significantly smaller than the dimensions of the drilling grid are less variable than the unknown reality (Armstrong and Champigny, 1989).Conditional simulation (CS) provides a series of plausible realisations that represent the actual grade variability at a small scale (eg 1 m + 1 m + 1 m). These simulations are very useful for a number of purposes, eg: optimising grade control, stockpiling and blending selection of optimal drill hole spacing assessing resource risk on contained tonnage and metal.At Yandi the major constituents of the ore (Fe, P2O5, SiO2, Al2O3 and LOI) are correlated to varying degrees. Independent CS of each assay variable will not reproduce these correlations. Reproducing the correlations (and the shape of scatterplots) is important if the simulations are used for the abovementioned purposes. This paper examines and compares various methods of CS that aim to reproduce the correlations between the assay variables.The CS methods evaluated in this paper are conditional co-simulation (CCS) using the linear model of co-regionalisation and two other, alternative multivariate simulation methods, which use min/max autocorrelation factors (MAF) or the stepwise conditional transform (SCT) to de-correlate assay variables before performing independent CS. It was found that CCS best reproduced the characteristics (histograms, variogram, scatterplots, etc) of the declustered drill hole data (Figure 1). Whilst simulation using MAF generally produced acceptable results, the method did not adequately reproduce the variance of the assay variables. The univariate statistics, histograms and experimental variograms were acceptable for simulations generated from the SCT. Bivariate statistics, cross-variograms and scatterplot reproduction for the SCT were unacceptable. The latter method produced inferior results because there were insufficient samples to obtain a reliable transform of the third assay variable in the transformation sequence.None of the abovementioned simulation methods provides good reproduction of all the scatterplots. This is due to the presence of clay pods, which cause some scatterplots to display two trends. These clay pods contain higher percentages of SiO2 and Al2O3 than the surrounding CID. The clay pods are generally smaller than the drill-grid dimensions. Thus their locations are typically unknown and they cannot be defined by manual interpretation, eg via wireframes. The locations of the clay pods were simulated via indicator CS. CCS was then performed separately for the clay pods and the CID. This significantly improved the reproduction of the correlation coefficients, the scatterplots and visually the simulation was more geologically realistic. Simulating the location of clay pods followed by CCS of assay variables is the recommended approach for simulation at the Yandi CID.CITATION:De-Vitry, C, 2013. Simulation of correlated assay variables - a case study from the Yandi Channel iron deposit, in Proceedings Iron Ore 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

As we look back through the Proceedings of our Institute, we find few papers dealing directly with education and recruitment. Apart from papers prepared in the earlier decades of this century, there was little written discussion on the subject until the 1950s, and mostly this was by the professionals, the professors and lecturers who staff the various mining schools of Australia and New Zealand.I use the term "mining school" in its fullest and widest meaning, to cover all aspects from ore to metal, and not in the narrow meaning that the word might imply. At the same time, in restricting the parameters of this address to "ore to metal" I recognize that I am excluding the very important fields of physical metallurgy and materials science; this I do because there is a limit to the quantum of any paper, and in fact these subjects are more closely allied to the use rather than the production of metals.However, the lack of education papers does not mean that education has been regarded lightly by The Institute. Sir Maurice Mawby in his presidential address in 1968, reminded us of the original objectives of The Institute, one 'of which was, "To promote the arts and sciences connected with the economical production of the useful minerals and metals ...". Our present Royal Charter is more specific when it says that one of the objects of The Institute is, ". . . to encourage the study of engineering with special reference to mining and metallurgy ...". If we recognize that in itself membership of our Institute is one means of continuing our education, it is true that education has been a concern of The Institute since it was first founded.Occasionally in recent years, an intrepid president has ventured to tell the academics what the industry needs, and he generally does this in a "no-question" situation! However it is encouraging that those entrusted with mineral education have always accepted this; they keep coming back for more and ask us to tell them what we want, and they will provide it.In 1948 a considerable dialogue on education was initiated when a standing committee was established by the Council of The Institute. In the period 1949 to 1951, three papers were prepared under the chair...

Jan 1, 1974

Within ten months of the first significant intersection on the Vera deposit, approval was given to proceed with a $28.3 M underground development of the Vera-Nancy gold mine. Contrary to what the timeframe suggests, the development of the underground mine was planned in a logical and methodical manner which enabled confirmation of the resource, evaluation of the orebody for mining and sufficient production to recommence milling operations at the Pajingo treatment plant. This paper describes the underlying factors on which the project was planned and developed. The approach has successfully enabled the mine to be in production 18 months after discovery without compromising any future production or potential expansion

Jan 1, 1998

In this address I look back over the past 40 years of mineral exploration in New Zealand û essentially the period since the Second World War (ie since 1945). It was the period of my personal involvement, and indeed of the personal involvement of a number of you. Luckily it was aperiod of great interest and activity. In the previous 50 years, virtually nothing had happened, and it is kindest to draw a veil over that period. In the very important earlier 40 years (1855 - 1895) the New Zealand gold rush occurred. That must have been a fascinating, rewarding period, which has been thoroughly documented by better historians than myself. I will simply comment firstly that its mineral explorers (gold-prospectors) were very successful indeed, and found most localities of the minerals they sought, in spite of using very different methods from ours of today. Secondly, they were preceeded by one of Maori exploration, which searched for a much restricted list of minerals, but succeeded in finding virtually every locality we know of today. The explorers of both of these early periods were obviously highly successful, but, in the time available, I must restrict myself to the period since 1945. I am currently editing the effective up-dating of Gordon WilliamsÆ 'Economic Geology of New Zealand' (1974). It covers the last 12 years or so. Many of you are contributing to that volume û both as authors and as referees û and I would like to take this opportunity of thanking you all. Although this new volume excludes the energy field, many of us have been involved in it, and I am therefore including energy minerals in this review, as Williams did in 1974.

Jan 1, 1987

By T C. Ooi, L Lu

Owing to ongoing development of new orebodies and changes to existing mining operations, new ore types with distinct mineralogy, porosity and textures are generated as feed for iron and steelmaking. Moreover, further product differentiation occurs as fine ores are increasingly beneficiated to achieve grade. A study was necessary to characterise a suite of iron ore fines in terms of their propensity for formation of quasi-particles and green bed permeability prior to sintering. In this study, two Marra Mamba bedded iron deposit (BID) samples, one Pisolitic channel iron deposit (CID) samples, two dense hematite samples (coarse and fine grained microplaty hematite), one hematite-goethite BID samples and one hematite-goethite bedded/detrital iron deposit (BID-DID) composite sample were investigated. Both Marra Mamba fines and Pisolitic fines exhibit the highest green bed permeability followed closely by hematite-goethite fines, fine microplaty hematite fines, hematite-goethite BID-DID composite fines and coarse microplaty hematite fines at a moderate sintering bed depth of 500 mm. While porous fines generally form better quasi-particles upon granulation than dense fines, the amount of moisture addition increased due to the moisture saturation of the porous fines. As sinter strands become ever larger and deeper, it was necessary to examine the granulation performance of these ore types at a range of bed depths ranging from 300 to 900 mm. On average, the green bed permeability achieved by different ore types, decreased by approximately 7.5 - 9 Japanese Permeability Unit (JPU) as the bed height was increased from 500 mm to 900 mm. In order mitigate the effect of lower bed permeability of the deeper beds, small additions of hydrated lime were investigated as a binding agent to facilitate the formation of strong micro-pellets. With the addition of three per cent hydrated lime, equivalent to approximately 2.3 per cent burnt lime, the majority of fines achieved adequate permeability for deeper bed sintering, with the exception of coarse microplaty hematite fines. In simulated coastal steelmaking sinter blends, it was found that the overall granulation performance of the blend is contributed to by individual fines constituting the blend. Therefore fines possessing favourable granulating properties impart better granulation to the blend as a whole.CITATION:Ooi, T C and Lu, L, 2013. Effects of ore type and binder addition on the formation of quasi-particles and green bed permeability at different sintering bed depths, in Proceedings Iron Ore 2013 , pp 459-466 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

East Otago gold deposits are hosted in Otago Schist that is the metamorphosed equivalent of Permian-Triassic Torlesse terrane greywackes. Relatively undeformed Torlesse sequences in Canterbury have <l m - 50 m bedding, with c. 500 m - l km and c. three kilometre scale units, typically either: 1) thick-bedded, massive, sandstones; 2) thin-bedded sandstone-argillite flysch; or 3) siltstone- or argillite-dominated units. Such lithological layering in Otago was intensely folded, deformed, and overprinted by metamorphic fabrics during Jurassic-Cretaceous regional metamorphism. Although primary sedimentary structures can no longer be recognised, a æghostÆ lithological variation is still present in Otago represented by psammitic (sand-derived), interlayered (sandstone-siltstone derived) and pelitic (siltstone-mudstone derived) schist. Lithological æunitsÆ in the schist are typically either 20 100 m or c.1 - 2 km thick, and are oblique to faults and shears hosting gold mineralisation at Macraes, Barewood, Nenthom, and Oturehua. Lithological variations and folds in lithological units are important in the along-strike distribution of gold in these deposits, and in the development of relatively high-grade pods and shoots at l00 m - 1.5 km scales. Ramps, flats and step-overs (known to be locally important for controlling mineralisation) are commonly located at lithological boundaries, presumably by local refraction of faults or shear zones as they propagated through folded stratigraphy. The various lithologies have also responded differently to deformation, causing variations in permeability that affected the penetration of mineralising fluids. Mapping lithological variations in barren host-rocks, either directly+ by fieldwork or indirectly by aerial geophysics, is a key to understanding and predicting the distribution of gold at mine and deposit scales.

Jan 1, 2001