Search Documents

By C Mark, Z Agioutantis

This paper presents an empirical design methodology that is based on successful US roof support systems using both primary and secondary support in coal mining entries and intersections. The recent nationwide dramatic reduction of roof fall rates, especially in areas with weaker roof, can be directly correlated to the effectiveness of the roof support systems. A large database of roof fall histories at several mines is used to define the approximate boundaries of three modes of roof support with respect to roof strength as classified by the Coal Mine Roof Rating (CMRR) and in situ vertical stress as indicated by the depth of cover. These roof support classifications are: • Suspension, where roof bolts mainly provide skin control for strong roof. • Beam building or reinforcement, where a roof of moderate strength can be supported by roof bolts only. • Supplemental (secondary) support, where the primary support by roof bolts may be augmented by several secondary support systems, eg cable bolts, trusses, additional roof bolts or standing supports. The Primary Support Rating index (PSUP) captures the capacity of the primary roof bolt system as a function of the actually implemented roof control plan, ie roof bolt length, roof bolt density, and roof bolt capacity, while it does not consider the type of bolt. The actual PSUP value is compared against a suggested PSUP value derived from statistical analysis of US case histories. Where secondary support is indicated, the expected rock load determines the necessary capacity of the secondary support system. A new (free) software package, Analysis of Mine Roof Support (AMRS), implements the design methodology and also allows comparison with other international indices such as the Reinforcement Density Index (RDI), the PRSUP, etc.

Nov 29, 2022

By R Varden

This paper summarises the process taken to simplify 35 ground support standards accounting for the multiple development profiles, dynamic geotechnical environment and the practical safety implications of a large-scale change in the ground control standards. This reduction was required after an incident involving incorrect standards being issued. The subsequent investigation identified that: • Selection of ground support standard for a mining instruction (MI) is not straightforward due to multiple standards, standards not reflecting current reinforcement used and complex geotechnical environment being encountered. Instead, site-specific ground control instructions were being issued. • Ground support standards were hard to follow and confusing, errors were present and not all standards to scale. • Ground support standards being used did not reflect what was being installed, ie bolt type incorrect and mesh orientation different. • No process or tier action response plan (TARP) for operators to follow for ground control standard noncompliance. • No justification for ground support standards being used in the current geotechnical environment. • No process for ground support standard selection and thereby no paper trail to document and assess adequacy of performance. A project was undertaken to reduce and simplify the ground support standards, produce a justification document to support ground support design and develop a process for site practitioners to identify the type of ground support standard required for the mining instruction. The exercise of rationalising the ground support was met with some challenges, including: • Technical aspects to determine the level of demand and the capacity for each ground support scheme. • Training the geotechnical engineers how to determine the level of risk for each area. • Winning over other technical services staff and the underground mining contractor of the new approach and then implementation. One of the major successes was the acceptance by the underground operators who found the system simplified their work and gave them increased confidence in management of seismicity. The rationalised ground support standards have now been successfully in place for over two years.

Mar 29, 2023

By J Light

Since 2019, the mine planning team at Olympic Dam has been establishing and maturing a shift from deterministic to probabilistic scheduling techniques. This paper outlines this journey undertaken by the mine planning team, key learnings from implementation and further work required to increase the level of planning maturity. Olympic Dam (OD) is a highly variable, polymetallic orebody with a vertically integrated value chain from operations to final product. The processing plant has a tight set of quality constraints which are managed through timing of stopes from varying parts of the orebody. Value is eroded for the operation when forecasted quality of the mine feed encounters disruptions from unplanned changes to the timing of stope starts. As production has moved from the historic Northern Mining Area into the more geologically complex Southern Mining Area, average stope size has reduced, resulting in increased mining fronts required to meet production targets. This has created a problem of increased schedule complexity and difficulties in identifying and communicating resource priorities within a large set of individual stope critical paths. The problem was approached by considering each stope as an individual project constructed by teams working across multiple projects at any one time. The operation could then be considered a multi-project environment with shared resources and enables the application of Critical Chain Project Management (CCPM) to the mine plan. Key to CCPM is the addition of time buffers to protect the critical path of a project form upstream or downstream processes. Implementation of time buffers protects the stope start date against compliance to plan variance. The monitoring of each time buffer consumption, as a proportion of total construction activities completed enables proactive prioritisation of resources. This resulted in an increase in the number of stopes starting in accordance with the mine plan, simplified communication of priorities to all levels of the operation, increased compliance to plan and a clear measure of schedule risk during planning routines.

Mar 29, 2023

By N Pranoto, E Lawell, T Dean, M Grant

The Goonyella Riverside Mine is located 30 km north of Moranbah in Central Queensland, Australia. Recent mining activities have exposed the north–south striking Kenya and Zimbabwe thrust Faults. These faults vertically offset coal seams by up to 25 m and locally thicken coal packages through imbrication of coal seams. The presence of back-thrusts add to the geotechnical complexity of maintaining highwall stability. The Kenya and Zimbabwe Faults have provided multiple challenges to the mining operation, with an unplanned additional 240 kt of coal tonnes being mined from imbrication of coals seams or from the refinement to local scale geological models. These additional coal tonnes have been either identified during the mining of the coal seam or just prior to overburden removal above the coal seam. These faults can also negatively impacted highwall stability with highwall failures, lowering the overall slope angle for pit designs and increasing stand-off distances for hazardous highwall conditions. Unmanned Aerial Vehicles are used to scan exposed highwalls and enable geological mapping via high-quality 3D images. Measure while drill data from drill and blast rigs can provide local-scale intersections of the faults and coal seams. Mine Geologists utilise these and other data sets to create localised geological models refined position of the fault planes and coal seams. These models are utilised by relevant mine site teams to ensure the safe and efficient mining of coal around these faults.

Mar 22, 2022

On a worldwide basis trackbound transportation is on the decline. As mining operations progress from open cast operations to underground operations, most utilise mechanised equipment. However, in South Africa hard rock mines, only a small percentage (¦10 per cent) of the production can be generated by mechanised methods and therefore trackbound mining methods will remain the dominant means to transport ore. In the Australian context there may be occasions where the nature of the orebody would dictate the use of rail transportation with the ore being transported from drawpoints by means of locomotives and hoppers. This paper focuses on horizontal rail haulage systems from the stope loading boxes to the shaft station area and will be largely based on South African experience. It is intended that this document will provide a practical guideline for mine designers and planners during the design process. The paper looks at trackbound transport systems and evaluates such items as construction and management of an underground rail haulage system. Current transportation systems for personnel, material and rock transportation are evaluated, gaps in technology highlighted, and recommendations made.

Jan 1, 2005

Jan 1, 2004

The Influence of Particle Shape in Rock Fracture

Sep 13, 2010

By S J. Hawke, L A. Dominguez

In non-ferrous metal mining operations, it is generally necessary to crush and grind the ore to a very fine particle size to effectively liberate the contained mineral from the host rock. Fragmentation by blasting is the first stage of this comminution process.Numerous studies and independent modelling of the Mine to Mill process have demonstrated the potential for significant downstream productivity improvements from improved blast fragmentation. However, safety and environmental constraints associated with the blasting process usually limit the extent to which blast energy or powder factor can be increased.An effective blasting solution has been identified that enables the safe utilisation of powder factors several times higher than those used conventionally to provide significant improvements in fragmentation. The solution uses a static ‘blanket’ of broken rock overlying the blast to contain this increased blast energy and control rock movement. To produce this broken layer of rock, the subdrill in each blast is significantly increased to preblast (or precondition) the entire stemming region of subsequent blasts on the next mining bench.The solution has been evaluated at a large open cut poly-metallic mine in Mexico. Results from the application of this technique have shown significant improvement in run-of-mine fragmentation, with subsequent downstream productivity improvement indicated.CITATION:Hawke, S J and Dominguez, L A, 2015. A simple technique for using high energy in blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By E Williams

The role and importance of a well designed test work program during the development of an orebody is often underestimated. A test work program should be tailored to deliver very specific answers to relevant questions. With a clear purpose, the results from the test work program will enhance the outcome of the feasibility study and provide the information required to meet the requirements of all stakeholders. With regard to test work programs there are three main areas that should be considered: orebody characterisation and definition, process flow sheet development and engineering design information.Orebody definition relies on reliable analytical methods to characterise and assess the economic minerals present in the ground. In mineral sands, the physical processing characteristics of the minerals play a significant role in the definition of an orebody. The analytical method therefore has to be customised using a combination of laboratory techniques. These techniques can include heavy liquid separation, gravity separation and magnetic separation and are usually combined with chemical and mineralogical analyses to create a picture of the orebody. During the definition phase of test work programs, an appropriate analytical technique has to be developed to evaluate drilling samples, but also to support the information collected during flow sheet development.Process flow sheet development is usually done once there is a reasonable understanding of the size and variability of the orebody. Selecting the best sample for test work is critical, as any flow sheet design is tied to the specific characteristics of the sample used for development. There are other factors that can improve the outcomes of flow sheet development test work, including the skills and knowledge of the operator and allowing sufficient time to process and analyse the results. Very often this work is conducted under pressure with limited time and resources, only to result in a suboptimal flow sheet. During this phase of flow sheet test work, iterative testing will provide the information required to develop an optimal metallurgical flow sheet. The data collected will provide indicative recoveries and yields that are required for feasibility studies.Equipment specification is often included as part of process flow sheet development. This includes comparative test work between different equipment suppliers, assessment of operating conditions such as the loading to determine the number of processing units required, as well as other design information required such as particle size distributions, density and operating temperatures.While restricting the time and costs expended on test work programs may seem to meet a short term need to meet investor requirements, neglecting to develop a proper framework of the requirements that has to be met in the long-term can lead to significant long-term cost overruns. This is mainly due to a need to repeat test work, or do confirmation test work, as insufficient information was collected during the initial program.

Oct 5, 2011

The placer gold industry has experienced a roller-coaster history incorporating four major boom eras. The first, 'hand-methods' boom arose in the mid-19th Century from application of an old idea in new places around the globe. The subsequent hydraulic mining, bucket dredging, and 'hydraulic excavator-portable plant' booms each arose from application of new ideas in old places around the globe, ie in places where gold had been found during earlier booms. The new ideas that heralded the second, third and fourth booms were all significant advances in excavation technology. These enabled the industry to target the known deposits that were too deep, too wet, too small, or too low-grade for recovery by earlier boom methods. Relatively few new deposits or new deposit styles arose from the 'history book' exploration approach, so the number of known deposits to which each of the boom methods were applicable was limited. Consequently, the first three booms were each followed by significant periods of industry decline, and the fourth boom is currently waning inNew Zealand. Further decline is not inevitable and can be avoided by changing to a knowledge-based exploration approach similar to that adopted by the hard rock gold industry in the 1970s. Such an approach could easily herald the next placer gold boom.   Most of the relatively coarse, easily won alluvial gold in proximal and medial reaches of the active placer systems is gone. However, a substantial alluvial gold resource remains in the distal reaches of active systems, and in ancient placers formed onshore and on the continental shelf during previous sedimentary cycles. The resource in these deposits probably exceeds the total New Zealand placer production to date. Successful development of these placers requires application of robust geologic models for the formation and distribution of the placers through time, and advanced exploration technology that has not been used before in New Zealand. Nevertheless, the knowledge and technology required to explore and mine these deposits is available now. Many of these deposits contain a large proportion of problematic gold types that are difficult to recover with the commonly used gravity technology without sustaining significant losses. Despite advances in recovery technology in last few years, too much emphasis is placed on the incorrect assumption that gold size is the primary control on recovery efficiency. Other gold particle parameters, especially particle shape, exert a much greater control on whether gold will be saved or lost to the tails, and must be considered in the design of recovery technology and configuration of recovery circuits.

Jan 1, 2003

By C Armstrong, B Wentzinger

Upstream embankment raises often represent the lowest cost option for increasing the capacity of tailings storage facilities (TSF), but also pose the highest stability risk due to constructing on top of previously deposited tailings.This paper presents an overview of key aspects in the geotechnical investigation and design of upstream raises and some recent lessons learnt from experience across a number of TSFs in Australia. A summary of recommended field investigation and laboratory testing methods is provided with a focus on collecting quality information for design purposes. A strong focus is given in developing an accurate assessment of pore water pressures, which, if not correctly understood can have disastrous consequences on tailings strength parameter interpretation and wall stability assessment in static and post-seismic conditions.The assessment of the contractive or dilative shearing behaviour of the tailings material and rigorous interpretation of design characteristic values are presented. Some comments on stability analysis options and proposed methodology are also provided.CITATION:Wentzinger, B and Armstrong, C, 2018. Lessons learnt in geotechnical investigation and stability analysis for upstream tailings storage facility raise design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 333–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By K Ringwood, J Cummings, C J. Moran

The development of a water accounting framework that enables consistent and contextual reporting of minerals operationsÆ water use, represents a key sustainable development objective that many Australian minerals companies have committed to. A future water accounting framework will require: key terms and definitions for water metrics for use in the Australian minerals industry that are consistent with the wider water sector, a suite of metrics representing key components of an operationÆs water balance, a calculation method for some of the metrics, and a reporting protocol. This paper presents the methodology that was used to derive these four components. Existing accounting frameworks were reviewed and key terms and definitions that were consistent with current regulatory requirements and voluntary approaches were proposed. A calculation methodology was developed to obtain some of the key indicators and variables that cannot be easily measured directly (eg water loss through evaporation). The adopted terms and definitions typically require a combination of empirical and estimated data. To test the proposed definitions and calculation methodology, values for water metrics were derived for eight sites, selected to test a variety of commodity and biophysical situations. The proposed framework and definitions could deal with the specific situations selected as case studies. The associated calculation methodology produced complete accounts at various levels. Some elements of the accounts could be directly checked against available data and simulations. The framework captured well variations in the reuse efficiencies; reuse efficiency could even vary for similar processes. It is concluded that this preliminary accounting framework provides a consistent language and metrics for quantifying and communicating water management, both at the intersection of the site with the surrounding landscape (through detailed reporting of site inputs and outputs) and within operational activities. Using this consistent framework for quantifying and documenting water use within an operation will provide a platform for compiling and comparing minerals industry water use with other sectors. This may support benchmarking activities within regions or companies and help demonstrate leadership amongst water users in water resource stewardship. The approach presented here is applicable to a wide variety of mining and processing activities, and biophysical environments, and following a period of stakeholder engagement and third party review, is being refined as a first step towards developing nationally consistent water use reporting for the Australian minerals industry.

Jan 1, 2009

By I Ritchie, G Lane, C Morley, D Yataco

Marcobre SAC (Marcobre) is developing the Mina Justa project in Peru. The project has a lower grade oxide orebody overlaying the higher grade sulfide orebody. The oxide ore is treated by acid leaching; consumption of acid is high and is managed by vat leaching rather than the more conventional heap leaching process.The leaching process uses ore crushed to 100% passing 8 mm to optimise copper recovery. Acid consumption generally increases with a higher proportion of fines. Marcobre is investigating a three-stage crushing circuit with high pressure grinding rolls (HPGR) in the third stage, instead of the more conventional four-stage cone crushing circuit. The use of HPGR can result in higher fines production due to the higher compression forces in the crushing zone. This paper reports on the outcomes of the test work completed by Marcobre in 2016 and 2017 to manage fines production and compare the use of HPGR with conventional crushing on a high acid consuming ore.At moderate pressing forces, a HPGR crushing circuit appeared to produce similar size distributions to cone crushing. On average, both the copper recovery and the acid consumption in subsequent vat leaching were higher with HPGR crushing than with cone crushing.CITATION:Lane, G, Morley, C, Yataco, D and Ritchie, I, 2017. Are there differences in size distribution when comparing conventional crushing and HPGR?, in Proceedings MetPlant 2017, pp 60–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By M Yahyaei, F Reyes, R Lage, V Jokovic

Equipment wear is strongly related to the performance of grinding circuits. In particular, SAG mills are subjected to the wear of their shell liners and grates. Changes in lifter height and face angle impact mill performance, while classification at the mill discharge is also affected as grates wear out. Moreover, liner mass loss caused by wear affects how operators interpret readings of sensors such as load cells or bearings pressure. Automating and optimising grinding circuits under these constrain becomes challenging due to the nonlinear and dynamic nature of the system. The operation of SAG mill grinding circuits remains largely dependent on human intervention, which frequently results in inconsistencies in performance across shifts, reflecting the operator’s personal preferences, experience, and other human factors. The influence of human factors can be reduced by careful training of operators as well as by automation using advanced supervisory control. The latter approaches could benefit from the development of dynamic process models that consider the effects of wear on the performance of equipment over time. This paper presents detailed industrial data showing the effects of wear on SAG mill performance. Additionally, a dynamic SAG mill model that accounts for these phenomena is proposed and demonstrated in a simulated environment. This model is shown to mimic the effect of wear on the performance of industrial scale mills and the operational constraints they are subject to, thus extending traditional SAG mill models. Incorporating wear into modelling and simulation platforms can improve the understanding of the effects that wear can have on the performance of key assets in comminution circuits and may allow the development of more robust model-based advanced process control strategies.

Aug 24, 2022

By C Li, D O’Dea, R Moreno-Atanasio, T Honeyands

The behaviour of iron ore granules in the feeding process of sintering is significantly influenced by the material properties of the granulated mix. Therefore, the measurement of key material properties of the iron ore granulated mix is indispensable prior to the simulation of the sintering process based on the discrete element method (DEM). In this paper, three key property parameters of the iron ore granulated mix, apparent density, elastic modulus and rolling friction coefficient, were measured in laboratory-scale experiments. For different sintering processes, the moisture content of the granulated mix normally varies according to the specific requirements for granule size distribution and operating conditions. Therefore, understanding the effect of moisture content on the property parameters of iron ore granules is very helpful in accurately determining the property parameters for DEM simulation work. In this paper, six groups of iron ore granule samples with six levels of moisture contents were prepared through granulation and the trends in apparent density, elastic modulus and rolling friction coefficient with the increase of moisture content were plotted and analysed based on the measurement results. The results show that as moisture increases from 6.9 per cent to 9.1 per cent, the apparent density decreases from about 3000 to 2800 kg/m3. With moisture increasing within the same range, the elastic modulus first decreases from over 200 MPa to below 100 MPa and then reaches a relative constant value of about 40 MPa at higher moisture contents. Rolling friction coefficients are measured using two methods with both indicating a similar trend, with the rolling friction coefficient first decreasing and then rising as moisture increases from 6.9 per cent to 9.1 per cent. The relationship between µr and µ’r is assumed to be similar to that between static and dynamic friction coefficients.CITATION:Li, C, Moreno-Atanasio, R, O’Dea, D and Honeyands, T, 2017. Variation in property parameters of iron ore granulated mix with moisture content, in Proceedings Iron Ore 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By S Long, D Carnovale, L Louwrens

The Mt Wright underground mine (MTW) is located near the town of Ravenswood in north Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited.The Mt Wright mine has gone through many stages, from the conception and implementation of the world first ‘sub-level shrinkage’ stoping (SLS) with continuous fill mining method in 2010, through to steady state production. These have been outlined in detail in papers presented by Mackay (2011) and Mackay, Long and Koen (2014) at previous Underground Operators Conferences.Since the last paper was presented, MTW has experienced significant change in two key areas.The first significant change was the discovery of a previously unknown hazard in the form of flat rilling events (FREs) from closed drawpoints (DPs). These events are believed to be unique to MTW and pose a significant risk to both the safety of personnel and the business as a whole. The paper will discuss this hazard and the evolution of the controls and practices that have been introduced to mitigate the risk posed by the identified hazards. The material involved in these events is extremely dry, fine and hot.The second significant change is an altered stress regime bought on in part by a change in the production front orientation and a general deterioration in ground conditions in some areas of the mine. This has caused some production interruptions at MTW. The second half of the paper will describe the challenges encountered, the mechanisms behind these challenges and the strategies implemented to safely return MTW production to planned levels.It is believed that other operations can learn from the issues mentioned above, and the paper has been written with this in mind.`CITATION:Long, S, Carnovale, D and Louwrens, L, 2017. Mt Wright – managing unique risks, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

The usefulness of laboratory studies - petrology and mineragraphy in the search for, and investigation of, mineral deposits should not be exaggerated, but it should not be overlooked, because such studies will always contribute to an understanding of the geology of the deposits, and can on occasions provide invaluable information not otherwise available. A few examples furnished by the investigations of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organisation will show this.Petrology.In the early stages of the investigation of the King Island scheelite deposit, during the war, when the nature of, the deposit was not understood, a series of samples embodying the exposed rock types was submitted to the Mineragrap;hic Section for petrologicalexamination by the Mineral Resources Survey. It was at once apparent to the petrologist that the King Island scheelite ore was a contact metamorphic deposit, in which a series of argillaceous shales, calcareous shales, impure limestones and limestones had beenintensely metamorphosed. The shales had been converted to finegrained biotite and actinolite hornfels, according to their lime content, and the impure limestones to fine-grained diopside hornfels, garnetdiopside hornfels and garnet hornfels (calc-flint), the garnet being the lime variety grossularite. The limestones, however, after being first converted to marbles, had suffered intense pyrometasomatism, involving substitution of immense quantities ,of silica and' iron for lime and carbonate, and had been converted largely to a coarsegrained garnet rock, in which the garnet was the lime-iron variety, andradite. The silica and iron were derived from the mineralising solutions of the adja,cent ,granite. intrusion, responsible for the contact metamorphism, and were accompanied by tungsten and some molybdenum. The tungsten in the presence of so much mobile lime, was precipitated as schecelite, much of it finegrained and enclosed in or intergrown, with the andradite garnet or the quartz interstitial to the garnet.It was apparent that the King Island scheelite deposit, was a perfect example of selective pyrometallomatic replacement in a bedded contact metamorphic deposit. The bedded nature of the original rocks was preserved, and the scheelite was practically limited to the original limestone beds, 'Which had been so much more susceptible to replacement after recrystallization, than the other sediments. The further geological study of the deposit then resolved itself into the task of mapping the folding and faulting of the deposit, with bore cores to provide the stratigraphic sequence, and establish the number of scheelite-bearing beds.A second example is provided by a petrological investigation of the mineral composition and genesis of the talc deposits of the Gumeracha district of South Austral.ia, which was undertaken at the request of the South Australian ,Mines Department, in conjunctionwith mapping of these deposits. The field geologist mapping the deposits was experiencing some difficulty in interpreting the structure...

Jan 1, 1950

By M L. Muller, A R. O’Donnell

The Mount Isa Mines (MIM) Copper Concentrator has an extensive history of reagent trials, with different reagents coming in and out of favour over the years. The research and use of carbon depressants is particularly prevalent, as carbonaceous pyrite is a major source of concentrate dilution. Years of research led to the use of naphthalene sulphonate due to its excellent carbon depression properties. However, due to rising reagent costs carbon depression ceased in the late 1990s. This led to the loss of knowledge about the use and value of naphthalene sulphonate. Cyanide is used at the Copper Concentrator for the sole purpose of pyrite depression and over the years multiple projects have been devoted to finding alternatives to it. In 2012 the neighbouring MIM Lead-Zinc Concentrator replaced cyanide with naphthalene sulphonate which resulted in cost savings and the elimination of a hazardous reagent. In 2013, plant trials were conducted at the Copper Concentrator in hopes to replicate the outcomes obtained at the Lead-Zinc Concentrator. The results of the trials conducted at the Copper Concentrator showed that naphthalene sulphonate could not replace cyanide and this work was set aside to pursue more promising projects. Further research conducted in 2014 found that mineralogy and a better understanding of the depressing mechanism of naphthalene sulphonate held the key to improved pyrite depression at the Copper Concentrator. The findings showed that Mount Isa copper ore contains two forms of pyrite; euhedral pyrite (cubic pyrite) and framboidal pyrite (carbon rimmed spheres of pyrite), both of which require different reagents to sufficiently depress them. Naphthalene sulphonate was found to be an excellent carbon depressant, suitable for depressing graphite and framboidal pyrite, whilst cyanide specifically targets euhedral pyrite.In 2015 laboratory test work was conducted to examine the use of naphthalene sulphonate in conjunction with cyanide to selectively target both forms of pyrite. This work led to a full plant trial, the results of which showed a significant increase in plant performance, with higher copper concentrate grades and recoveries being achieved. This paper aims to focus on the benefits and importance of understanding past work and linking a detailed knowledge of feed mineralogy to reagent selection for improved plant outcomes.CITATION:O’Donnell, A R and Muller, M L, 2018. Selectively targeting hydrophobic gangue minerals at the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 413–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

In considering the organization of research, it is necessary to know just what research is, what objects are in mind when setting out to conduct research, and what are the functional units which are required to enable a coordinated effort in research to proceed.The dictionary defines research in the following terms: Laborious and patient search, as for truth, diligent inquiry or examination in seeking facts or principles; inquiry, scrutiny; to search or examine with continued care; to seek diligently; to search again; to examine anew.This is, of course, simply a formal definition, but the reference to "labour", "patience" and "diligence" should be noted.The following quotation from an answer to the question "What is Research?", published recently in a technical journal, puts some life into the formal definition:- Essentially, it (Research) is nothing but a state of mind a friendly, welcoming attitude toward change. Going out to look for a change instead of waiting for it to come. Research, for practical men, is an effort to do things better... The research state of mind can apply to anything: personal affairs or any kind of business, big or little. It is the problem-solving mind as contrasted with the let-well-enough-alone mind . . . It is the "to-morrow" mind instead of the "yesterday" mind. Note the statements that: Essentially, it (Research) is nothing but a state of mind, and the research state of mind can apply to anything.

Jan 1, 1950

By S Das

Deposit-10/11A is situated in the iron rich Bailadila region of India comprising haematite ore of average grade 65 per cent Fe. The deposit production line was commissioned in the year 2002 having a capacity of 5 Mt/a. The plant has the state of the art mineral processing equipments.The ore is transported from mines to crushing plant by means of dumpers. The ore is comminuted in two stages to get 150 mm top size product and this product is transported through conveyor system and is stored in silos as feed stock for beneficiation plant. In the beneficiation plant this crushed product is wet screened in two stages to produce a product of lump (-150 + 10 mm) and fines (-10 + 3.15 mm). The product of -3.15 mm top size is fed to primary classifier for a size separation at 150 µm. The resultant product (-3.15 mm + 150 µm) is dewatered and transported to fi ne ore product stock yard through conveyor system. The minus 150 µm material from classifier overflow is fed to cyclones (508 mm cyclone battery with an apex of 65 mm) for desliming at 45 µm and to recover ultrafi nes (-150 + 45 µm). The cyclone overfl ow slimes (-45 µm) along with water is treated in lamella thickeners to recover process water. The thickener underflow material is transported to tailing pond (discharge rate is 300 m3/h at a specific gravity of 1.4) by pumping through HDPE (high density poly ethylene) pipeline and the over flow water is being recirculated. The water requirement for beneficiation is approx 1.5 m3 per ton of ore.This paper aims at identifying and quantifying the factors that affect the overall plant performance (grade and recovery) during the different seasonal variations especially in the rainy season (mid-June to end October). The effect of seasonal variations on unit operations such as milling, classification, thickening and filtration are discussed. Specific cases are presented as examples and recommendations are formulated.

Jul 11, 2011