Search Documents

By Warren L. J

In the mineral processing industry solid-liquid separation within a thickener usually requires the addition of a synthetic flocculant to enhance the settling rate of fine particles. The characteristics of the resulting flocculated suspensions may vary considerably depending upon the physical and chemical conditions which prevail during the flocculation process. For example, parameters such as flocculant type, dosage and solution concentration, surface chemical characteristics of particles and the suspension agitation conditions can influence the degree to which the particles aggregate. Aggregated suspensions exhibit various structures, and range from those composed of small, dense aggregates to those containing large, voluminous aggregates. The size distribution and structural type of the aggregates which form within the feed-well of a thickener can have a dramatic effect upon overall thickener performance. Thickener performance cannot be optimized without optimization of the aggregate structure produced in the feed by synthetic flocculant addition. This has required the development of new techniques to quantify the nature of aggregated suspensions, details of which are presented in this paper.

Jan 1, 1989

High pressure (-1.2 GPa) Early Cretaceous granulite facies orthogneisses in Fiordland, New Zealand are in tectonic contact with a cover sequence comprising mid-Palaeozoic amphibolite facies metasediments, subordinate metavolcanic rocks and syntectonic granitic orthogneisses. This cover sequence and the underlying granulites constitute upper and lower crustal plates of a mid-Cretaceous metamorphic core complex whose emplacement was linked to continental rifting and the Late Mesozoic breakup of the Pacific margin of Gondwana. Exhumation of the lower plate granulites occurred in two stages. The first stage was associated with extreme attenuationand tectonic denudation of the cover sequence accompanying emplacement of the core complex, leading to rapid uplift of the granulites but without generating the large volumes of Fiordland-derived sedimentary detritus normally expected if uplift and erosion were the only factors involved in unroofing the granulites. Final uplift and exposure of the granulites at the surface occurred mainly during the last 10 Ma in response to transpression across the mid-Tertiary Alpine Fault and/or the obduction of Fiordland continental crust over oceanic crust of the Tasman Sea.

Jan 1, 1990

By I Kolomaznik

Each technological process can be reduced on the transport networks, and namely on the parametric networks and the non-parametric ones. The parametric networks are created by the piping, electrical cables or channels. The non-parametric network is created by the ways, suspended grooves, trackages and also by the belt conveyors or other conveyors for continuous material transport. If we reduce the technological process on transport networks, then, by the creation of these networks models and their mutual interconnection we obtain the model of the whole technological process. The model can be understood as the universal one, without exaggeration, because it is valid for any technological process. However, for us the mining production process is important what represents the mining and transport of raw materials under the support of the ensuring system. In this contribution one of the first attempt is described, and namely how to connect the parametric network which has been already worked out very properly with the non-parametric network what is presented in this contribution by the transport line of belt conveyors.

Jan 1, 2003

By Koh P. T L, Varnas S. R

Fluid flow, heat transfer and combustion in a nickel flash smelter have been investigated by numerical modelling and flow visualisation. The three-dimensional numerical model incorporates turbulent two-phase fluid dynamics, radiative heat transfer and combustion. The main features include the use of the k-E turbulence model, the Lagrangian tracking of particles, radiative heat transfer based on the spherical harmonics method, and chemical reactions. The predicted flow fields are in good agreement with data obtained from a series of flow visualisation experiments on a cold water model. The interaction mechanism between the fluid flow and the solid particles is examined for a range of particle sizes both with and without injected oil in a series of simulations. The heat transfer in the shaft is dominated by combustion and radiation, whereas the ignition of particles is influenced by the particle size and the added oil. Flow and temperature fields for both gas and solid particles are presented as well as the fraction of sulphur removed from the particles.

Jan 1, 1992

Degussa's PAL-system (peroxide assisted leach) has been proven to be more economical than the conventional cyanidation technique. Significant in- creases in the gold recovery have been reported, accompanied by savings in cyanide. Accelerated extraction kinetics and modified reagent demands necessitate a redesign of the conventional cyanidation plant. The South African Osprey Mine is presented as an example of a successful PAL-application. Based on the plant and laboratory data it is shown that the redesign of the flowsheet can be an important factor for the effectiveness of a metallurgical plant. In the case of the Osprey Mine, the PAL-technology all ows a modification of the current preoxidation-ClPcircuit to two separate CIL-plants to treat run-of-mine ore and old tailings dumps. A doubling of the throughput is possible without enlargement of the plant. This innovation in the field of gold extraction, the combination of the PAL-process with a redesign of the metallurgical plant, can be considered as a basis for a more profitable gold mine.

Jan 1, 1991

By Komosa T, Muir D. M

Mixtures of ammonia and cyanide at low concentrations leach gold selectively from copper-gold ores. The effects of various reagent compositions on three different ore types containing between 0.3 - 1.5 per cent Cu are reported. It is shown that the results and optimum compositions vary according to the ore, which is attributed in part to the mineralogy and adsorption of solution species on the mineral surfaces. The solution chemistry of the Cu-NH3-CN system indicates that Cu(CN)a - and Cu(CN)3 species are involved in the leaching mechanism. Rotating disc studies on pure gold and copper are reported which show that the Cu(CN)32- species leach gold at about half the rate of CN but leach copper at the same rate. The presence of ammonia retards the leaching rate further. Mixtures of Cu(CN)a3- and NH3 effectively leach gold from Telfer tailing without leaching copper. The role of ammonia appears to be to control the precipitation of copper rather than the kinetics of leaching.

Jan 1, 1991

By B Sno, P A. Cockburn, R C. West, C U. Jones

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed), which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons feed system could deliver the following benefits to flash furnace operation: accurate pulseless delivery of feed material to the head of the burner leading to improved combustion performance and process stability; highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; decreased pressure pulsation in the furnace due to improved combustion control and performance; and decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear.

Jan 1, 2005

By Fowler T. J

Examples are provided of discontinuity analysis at selected sites in central Victoria. Discontinuities are rock fractures of low tensile strength, including bedding, foliations and joints, which are analysed during rock excavation design, to quantitatively determine the defect orientations, spacing and lengths. Their analysis can reduce the cost of mining operation and improve safety. Extrapolation beyond the exposed face is required, although difficult without an understanding of the regional geology. For rock engineering purposes assumptions are commonly made that discontinuity characteristics are uniform throughout the rock mass, however this is often invalid, as rock masses have usually undergone large-scale deformation, exhibit anisotropy and inhomogeneity. Structural geologists are able to interpret large-scale deformation responses for the purposes of structural correlation and extrapolation. Examples of discontinuity analysis linked to regional geological assesment from sites in central Victoria, reveal that discontinuities exhibit similar characteristics in a range of rock types of different ages and composition. Spacing variations between individual sites are believed to be a result of local rock type differences.

Jan 1, 1997

By Russell F. M

Following the accident in the Peterson section of Mufulira mine in September, 1970, a method had to be found of extracting up to 300 000 tonnes of ore per month from this area without inducing caving. Sandfill mining methods were chosen, necessitating a plant capable of producing both cemented and uncemented fill on a large scale. The paper covers the design and construction of this sandplant which is thought to be unique for its size, as it incorporates three 3 000 tonne capacity settled storage silos, a 500 tonne capacity cement silo, mixing tanks and a control room situated underground. The plant is designed to handle an aver- age of 440 tonnes per hour with a maximum of 660 tonnes per hour for limited periods, delivering either uncemented fill or cemented fill in proportions varying from 1:6 to 1:30. The instrumentation and equipment necessary to give one man operation of the plant is described and the fill mining methods now in use at Mufulira are briefly outlined.

Jan 1, 1973

By Carter NB

A statistically-designed experimental program has been used to study compositional and processing variables which influence the development of strength and reducibility of iron ore pellets. The effects of chemical composition and processing variables were investigated by indurating laboratory-made green pellets, of known composition, under approximately isothermal conditions in a pot- grate simulator. Some findings from a six- variable study are summarized in the form of contour diagrams and emphasize the importance of interactions between the variables. Production of strong, highly reducible pellets is possible over a considerable range of combinations of temperature and firing time. Abrasion index (AI) and cold compression strength (CCS) improve as both these variables increase, but reducibility (R) declines, so a compromise is required. When the lime level is too low to form enough slag for bonding, the AI and CCS may be inadequate. Larger additions of lime tend to improve AI and CCS, with only slight effects on R. Finer grinding of the balling feed (i.e. higher Blaine index) tends to improve Al and CCS without

Jan 1, 1980

By Mckenzie CK

Delay scatter, although widely recognised, has rarely been studied with the aim of critically reviewing blast designs. With current trends towards increased deck charging, and the effect on the number of separate delays in blast designs, delay scatter is shown to have a rather profound influence on the control of initiation sequence and the ability to successfully con- duct pre-splitting and smooth blasting. Determination of realistic delay scatter distributions is the first step towards application to blast design. Delay scatter must be evaluated in terms of deviation from the nominal time, not in terms of deviation from the batch mean, since the latter is not usually known without specific testing, requiring accurate timing instrumentation. Computer programs using Monte Carlo simulation can then be developed to investigate the probabilities of out-of-sequence initi- ation or near-simultaneous initiation within any specified interval. The procedures have been applied to both production and development blast designs in Australia and Chile to improve initiation sequence control and to rationalise and simplify blast designs.

Jan 1, 1988

By Weber W

Methods of calculation of the reliability of process computers are getting more and more important. The paper presents long period observations of 21 process computers with online applications in the iron and steel industry. About 5000 failure events during 10 years have been systematically recorded and evaluated. On the basis of these long time observations it is possible to develop a probability model of the failure behaviour of process computers.This failure model is constructed with four different states of the process computer:Working phase, working phase with undetected reasons, repair phase, failure phase resulting from external influences.The model is defined by differential equations for the probability of one of these four phases. Long time observations show, that all of these four phases are closely correlated with the capa-city of a process computer, restarting without detection of failure reason, changes of programs and software, costs and time of repair. So the result of this analysis is a model of failure for process computers, which allows to predict breakdowns of process computers on the basis of external parameters.

Jan 1, 1985

Production of refined zinc (99.95 per cent) at the minesite without increasing greenhouse gas emissions is considered. As an example, exploitation of the full reserve of the McArthur River orebody is proposed, using the existing concentrator, whilst introducing radically innovative smelting technology. Bulk flotation of all the sulphide minerals is followed by smelting in a melt circulation reactor with tonnage oxygen. By smelting the high-energy pyritic concentrate and reacting the evolved sulphur dioxide with near-mine dolomite, a large amount of electricity can be generated. This is enough to supply all the requirements for the smelter itself, an air separation plant and a facility for compressing and liquefying carbon dioxide. Carbon dioxide is disposed of off-shore for enhanced oil recovery or by other means. The reacted dolomite fixes sulphur as an inert and environmentally acceptable solid residue. Treatment by these means leads to virtually zero gas emission smelting. The paper concludes with a vision for the future in which expansion of zinc smelting capacity is seen to be definitely needed.

Jan 1, 1998

By Griffiths L, Marshall P

fhis paper describes investigations into drainage of gas from the solid to control outbursts. Initial studies conducted on drainage of shear zones showed that, given enough time, these can be successfully drained. Once drained, they can be intersected and driven through without any activity of outbursts. The results of programme of investigations to determine parameters for drainage from the solid show that gas flow rates from the Bulli Seam on the average are about 2 litres/min/metre length of borehole. But when shear zones are intersected, the flow rates could be as high as 8 litres/min/ metre length of hole. Shear zones can be picked up from pressure measurements 50 - 60 m away and this could give sufficient time to drill through these zones and drain them in advance. Systematic drainage of Bulli Seam at West Cliff Colliery could eliminate or reduce frequency of outbursts considerably. At present drainage holes are being drilled systematically in the seam, with drainage installations on the surface. Gas purity of 80% methane is being delivered at the surface plant.

Jan 1, 1980

The firing of mass blasts at Isa Mine is a normal operating practice. Both electric and non-electric initiating systems are being used for this purpose. The advantages gained by large firings relate to the Planning, Scheduling, Services and Production functions of Isa Mine. More efficient us"e is made of manpower due to the concentrated charging effort and con- tinuity of the charging operation. In addition, the requirement for ring firing personnel to work at the edge of large stope voids is reduced. Better fragmentation results from the interaction of adjacent detonating rings of blastholes and in flight collisions. With mass blasts there is also less chance of large blocks of ore, created by faults or joints, falling into the stope and creating problems at the drawpoints. The formation of a large tonnage of broken ore facilitates production at scheduled rates from that stope source. The weight of explosive detonating during a mass blast can be considerable. Isa Mine has achieved satisfactory blasting results without excessive ground vibration levels and present knowledge indicates that pillar ground stab- ility has been maintained.

Jan 1, 1978

LOCATIONThe property of the Mount Isa Mines Ltd. is situated in Western Queensland, 603 miles by rail west of Townsville, the nearest seaport. All supplies and the bullion are railed between Mt. Isa and Townsville. The climate is semiarid, and operations are conducted throughout the year without difficulty.WATER SUPPLYThe mill make-up water is obtained from the mine, and also from Rifle Creek reservoir, which is situated 20 miles from Mount Isa. The domestic supply of water is obtained from a series of bores on the company's leases.POWER SUPPLYElectric power at 3300 volts, 3-phase, 50 cycles, is supplied from the company's steam power plant, consisting of two units, each unit comprising one Babcock & Wilcox boiler, supplying steam at 300 lb. pressure per sq: in. to one 5000 kW. turbo-alternator. Pulverized coal is used as fuel, and power is being generated at a cost of 0.45d. per kilowatt hour. The coal used is supplied from the State Coal Mine, Bowen, costing 42/- per ton delivered at Mt. Isa.

Jan 1, 1933

I must tell you at the outset that I come to this conference deeply disturbed at the `role of Government in international dealings in mineral and energy resources'. I am disturbed by the confusion that now passes for policy. I am disturbed by the short- range view of critical problems taken by a majority of Governments. I am equally disturbed by the even shorter range of view taken by a growing army of industries. Many of them clamour for Governments to solve their problems in a specific way, with little regard for any other sector but their own-and with even less regard for the fact that every time a Government takes over some of their responsibilities they surrender some of their freedom. I would not say that longer range views don't exist. But I would say that they don't prevail at the present time. Instead, we are seeing the con- stant development of many policies for individual problems which don't tackle the fundamental causes. We must get back to basics without delay.

Jan 1, 1978

The rights of nations to explore and exploit minerals in the continental shelf were recognized by the 1958 Convention on the Continental Shelf. The Commonwealth Government has expressed the view that, as a party to the Convention, it has, by virtue of its foreign affairs power, full rights to legislate with respect to offshore minerals. States have taken the view that the rights recognized as extending into the continental shelf are land mineral rights, which belong to the States, and the Commonwealth legislative power in this field is strictly limited. Without prejudice to each other's rights, Commonwealth and States agreed to "mirror" legislation in relation to offshore petroleum. Commonwealth and State legislation, of which the operative parts are in identical terms, are both administered, in relation to areas adjacent to each State, by State Ministers of Mines. The legislation has functioned well in practice, though difficulties are encountered by the Commonwealth Government due to lack of direct accountability to Commonwealth Parliament. An alternative scheme designed to overcome this problem is outlined.

Jan 1, 1974

By J Webb

Anoxic limestone drains (ALDs) have been widely used in the passive treatment of acid mine drainage (AMD), but their effectiveness has often been less than anticipated. Iron hydroxide often precipitates around limestone particles and inhibits neutralisation. To determine the conditions under which iron hydroxide precipitates, a small-scale laboratory ALD system was built to enable a detailed examination of the chemistry of iron within the drain. For one experiment, a mixture of limestone and quartz was introduced to the drain to assist in the determination of the key mechanism governing iron precipitation. Synthetic anaerobic acid mine drainage containing Fe2+ (~130 ppm), SO4 2- and H+ was pumped at a rate of 30 mL/min up a 90 cm tall, 15 cm diameter vertical column filled with limestone gravel of 98 per cent purity. Three sampling ports were fitted at equal intervals along the column; water was periodically extracted for analysis at the sampling ports over an 11-hour period. Experiments were run at influent pH levels of 2 and 4. Results show that acid neutralisation to pH greater than 6 occurred at the inflow end of the drain. The greatest amount of iron precipitation (19.5 per cent) also occurred in this area. The lack of iron precipitation on the quartz surfaces in the quartz/limestone mixture indicates that neutralisation is the key mechanism for the precipitation of iron hydroxide on limestone particles. A pe-pH stability diagram derived for the laboratory ALD system indicates that ALDs will not be effective for AMD with pH 2. Influent waters with pH 2 require a pe of -2 (Eh: -118.4 mV) to avoid Fe precipitation upon neutralisation. Influent waters of pH 4 require a pe between -2 and -4.

Jan 1, 2003

By Fairhurst RM

High pressure abrasive water jets have been shown capable of cutting a wide range of materials including steel, stone, rock and concrete. Acceptable performance can be achieved using relatively low pressures and expendable abrasives. The cutting head can be made small and abrasive feed systems have been developed that allow reliable pumping of slurries over long distances to supply such cutting heads. These features make abrasive water jets ideally suited to automated control in remote areas.Another major advantage of abrasive entraining water jet cutting heads is that they may be operated safely in potentially explosive environments due to their cold cutting ability. Therefore there are many possible applications for such equipment in mining.This paper gives an introduction to the abrasive water jet process and includes results of trials carried out at BHRA on a range of hard materials. Work is also described which investigated the operational safety of abrasive water jets in explosive environ-ments. In a special environmental chamber, cuts were made on steel and sandstone with atmospheres of methane/air and hydrogen/air, without caypsing ignition.

Jan 1, 1985