Search Documents

By A Rantala, J Timperi and J Kaartinen, T Maksimainen, O Haavisto

"X-ray fluorescence (XRF) is the most common technique used for online slurry assaying in base metal flotation applications. Typically, assays from feed, concentrate and tailings slurries are used to monitor and control the flotation circuit, with possible additional sampling locations in other main slurry flows inside the circuit. The elemental content detection from the XRF spectrum is relatively straightforward as the spectrum contains element-specific peaks whose height corresponds to the element concentration in the sample. However, centralised XRF analysers measure the elemental concentrations line-by-line, which may increase the sampling interval for an individual line and cause unnecessary response delays, especially in large flotation plants. Reflectance spectroscopy is an emerging technique that can be used to obtain more frequent measurements from slurries. The measurement is based on the mineral-specific absorbance of light in the visible and near-infrared (VNIR) wavelength range. Due to this relatively inexpensive and simple measurement system, it is possible to conduct the measurement simultaneously in several slurry lines. However, the information contained in the VNIR spectra is more difficult to interpret as concentrations of all the minerals in the sample contribute to the measured spectrum and changes in solids content, particle size and mineralogy disturb the elemental content estimation. Therefore, frequent calibration of the measurement is required. This study presents the application of combined reflectance spectrum and XRF measurements for rapid online slurry assaying in a copper-nickel flotation plant. The XRF assays are utilised as calibration samples for the reflectance spectrum measurement, keeping the calibration model up-to-date. The rapid reflectance spectrum analysis is then used to provide an almost continuous estimate of the slurry contents, enabling further improved process monitoring and control.Citation:Haavisto, O, Maksimainen, T, Rantala, A, Timperi, J and Kaartinen, J, 2016. Reflectance Spectroscopy with X-ray Fluorescence for Rapid Online Assaying in a Copper-nickel Flotation Plant, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By G Caddy, M Middleton, S Kerec, R Keil, J Tsalapatis

Arrium’s OneSteel Whyalla Steelworks in South Australia is a fully integrated plant which operates a single blast furnace. The key operational objective has been to maintain high process availability and stability while maximising the process efficiency and the produced hot metal quality. All ferrous raw material input feeds are sourced exclusively from company iron ore deposits in the nearby Middleback Ranges. The Whyalla blast furnace has mostly operated using a combination of a high percentage of pellet feed, produced in Whyalla, together with screened lump ore.The unique ironmaking challenge has always been to extract the maximum value from the ferrous burden feed available locally. In earlier times, high-grade hematite lump ore was available for both screened lump ore and pellet production. Blast furnace trials from acid to fluxed pellet feed commenced in 1977. The furnace pellet feed has been wholly fluxed since 1981. Many pellet/lump ore feed mixes and significant pellet chemistry composition design changes have been made over the years. These changes have been aimed at best balancing the ferrous burden availability/cost and the optimum reducibility/high temperature melting behaviour of the charged ferrous feed within the blast furnace. In more recent times since 2007, the Whyalla blast furnace operation has transitioned from a hematite based pellet feed to a magnetite based pellet feed while there is an ongoing contest dealing with diminishing absolute quality/increased variability raw material feed inputs.The paper will detail key elements of the Whyalla blast furnace operational philosophy with regards to ferrous feed use and process optimisation. The blast furnace ferrous feed design considerations will be discussed, together with the test work performed, the operational and slag design transition strategies employed and the process results achieved.CITATION:Tsalapatis, J, Middleton, M, Keil, R, Kerec, S and Caddy, G, 2015. The use and optimisation of ferrous feed at the Whyalla Blast Furnace, in Proceedings Iron Ore 2015, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Rantala, C Cruickshank, I Muzinda, O Haavisto, J Timperi

The production at First Quantum Minerals’ (FQM) Kevitsa Mine, located in northern Finland, commenced during the second quarter of 2012. Presently, the mine processes approximately five and half million tonnes of ore annually, producing nickel, copper and platinum group metal (PGM) concentrates. In order to support fast production ramp-up and optimise the performance of flotation thereafter, an extensive advanced flotation control solution was implemented by Outotec in collaboration with FQM Kevitsa.In addition to basic process instrumentation and process control, each of the 14 Outotec 300 m3 and another 26 cells, ranging from 20–160 m3, have been equipped with state-of-the-art systems providing froth image analysis and automatic froth speed control. Also, the flotation cell levels are stabilised with advanced feed-forward level control.The online analyser provides key feedback information of the process performance for the advanced process control (APC) system. Based on this information, APC system defines grades and recoveries according to rules defined by Kevitsa process metallurgists. This system executes the control strategies for optimising the production of concentrates.Throughout the implementation and support phases, specific and intensive attention was paid to ensure plant personnel gained full understanding of interacting with the system and how to incorporate their process experience and skills to optimise the APC strategy. This level of expertise is also a valuable asset in understanding the APC system’s contribution to the overall performance of the plant as well as providing the ability and confidence to define key performance indicators used for continuous assessment. The experiences and results from site achieved so far are discussed in this paper.CITATION:Rantala, A, Muzinda, I, Timperi, J, Cruickshank, C and Haavisto, O, 2014. Implementation of advanced flotation control at First Quantum Minerals’ Kevitsa mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 369–378 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By S Li, Y Lei, X Wu, C Ma, W Q. Zhang

The failure of roof of thin bedrock working face under loose aquifer in a coalmine can lead to water-sand inrush disaster. Based on the accident of water-sand inrush in 30108 working face of a mine in Shaanxi province, China, the mechanism of water-sand inrush is theoretically analysed. The process and critical conditions of water-sand inrush in working face are reproduced by numerical simulation where the bedrock thickness is 20 m, the clay layer thickness is 40 m and the mining height is 6.5 m. The study found that under the condition of thin bedrock and thick clay layer, the characteristics of the clay layer have a significant inhibitory effect on the development of the fractured zone, and the development of the water-conducting fractured zone is incomplete and insufficient. However, in the process of continuous mining of multiple adjacent working faces, the strength of the clay is gradually reduced by the influence of mining and the erosion of water, and the height of the fractured zone is gradually increased. In the subsequent mining process of the working face, the roof is more likely to be cut-off and lead to water-sand inrush. From the initial failure of the clay to the final crack directly through the surface, the shear strength of the clay is reduced by about 52 per cent. Further simulation found that in addition to the characteristics of the clay layer itself, the main factors affecting the water-sand inrush in the working face caused by overburden failure also include the difference in bedrock thickness and strength, and the difference in coal seam mining height. With the increase of bedrock thickness, the development height of the fractured zone increases gradually with increases of bedrock thickness when the cutting failure of overburden rock no longer occurs. With the increase of mining height, the height of water flowing fractured zone also increases, but the cracking ratio gradually decreases. Therefore, it’s of great practical significance to systematically study the mechanism and critical conditions of water and sand inrush in mines and the main influencing factors for preventing similar accidents in mines with similar conditions.

Nov 29, 2022

By T Soares, P Esteves, C Senna, V Souto, E Dias

Steinert provides a wide portfolio of Sensor Based Sorting (SBS) technologies, including the possibility to combine different sensor data in the development of the separation applications. This multi sensor approach provides a larger applicability and extensive flexibility for the technology. This effect is emphasized for mining applications, once every ore body presents its own features that can also comprise a large material variability. In this sense, every sorting application is customized and comprises a personalized solution. This means each project development includes a test work stage that approaches from the project discussion, test definition, up to test outcomes and processing development. In relation to very complex and large projects, a sorting pilot scale plant has become a crescent tendency. By having a pilot plant stage can represent a chance to test larger amounts of material from different mining areas, different mining projects, such as to consider different processing targets and application approaches. Based on that, a better understanding about the technology application can guide a more assertive development of large and complex ore sorting projects. The aim of this paper is to provide information about the applicability of the Steinert multi sensor technology at different pilot plants in South America. It consists in a compilation of laboratory test results, plant design and operational results. For that, a chromite, an IOCG deposit and a sulphide gold ore projects are presented. Additionally, the paper discusses the application of different sensor technologies combinations such as various processing targets, thus providing a wider understanding about sorting applications and flexibility.

Nov 10, 2020

A combination of new radiometric age dates, local field relationships and the regional tectonic history indicate that the low sulphidation, fault breccia-hosted, epithermal gold-silver mineralisation at Umuna is related to continental rifting processes rather than subduction induced deformation and magmatism. K-Ar and Ar-Ar age dating of secondary sericite associated with the gold-silver mineralisation indicates that the alteration crystallised between 4.0 and 3.2 Ma, whereas relative age relationships and SHRIMP II U-Pb dating of the abundant Boiou porphyry intrusions on Misima confirm that the calc-alkaline plutonism is significantly older (8.1 f 0.4 Ma) and related to a different tectonothermal event. The Woodlark Basin sea floor spreading centre occurs to the north of Misima and has continued to propagate westwards, into the continental basement of the Papuan Peninsular, since the end of the Miocene. The westernmost tip of sea floor spreading centre is presently to the east of the D'Entrecasteaux Islands but would have been to the east of Misima roughly 4 Ma. Many of the young tectonothermal features in the D'Entrecasteaux Islands (hydrothermal activity and associated epithermal mineralisation, metamorphic core complex exhumation, detachment faulting, peralkaline volcanism, half graben type basin formation) can be attributed to major extensional deformation ahead of the propagating rift system. Similar tectonothermal features on Misima are temporally associated with the epithermal gold-silver mineralisation at Umuna, suggesting that the D'Entrecasteaux Islands are a modern day tectonic analogue for Misima at the time of precious metal mobility and deposition. The rapid exhumation of high grade metamorphic rocks and localised

Jan 1, 1997

By W Potma, C Brauhart, S Halley, S Urbisinov, A Scogings

Truly integrated, quantitative, 3D GEOmetallurgical (or mineral system) characterisation, classification and 3D modelling should provide a cradle to grave unifying link across the exploration and mining value chain. All too often, spatially representative (quantitative) characterisation and modelling of a mineral system is delayed until feasibility stage, incurring a significant opportunity cost. The application of robust GEOmet characterisation methods early in the project lifecycle (at exploration stage) improves ground selection, exploration, and Mineral Resource estimation outcomes, long before there is a need for metallurgical test work. The value of this early provision of quantitative 3D mineralogy models is compounded at project feasibility stage, and continues to accrue over the entire project lifecycle, delivering cost savings, improved decision making and early warning of issues and opportunities.CITATION: Potma, W, Halley, S, Scogings, A, Urbisinov, S and Brauhart, C, 2018. Putting the ‘GEO’ back in front of GEOmetallurgy: importance of early implementation of quantitative mineral system characterisation, classification and modelling, in Proceedings Complex Orebodies Conference 2018, pp 55–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By L S. Barbour, M K. Meiers

Soil covers for mine waste are subject to changes in structure as a result of root development, and wet/dry or freeze/thaw cycling. The purpose of this study was to evaluate the changes in the hydraulic conductivity of three non-compacted clay covers over time. The covers are located on a sodic/saline overburden fill (30-Dump) at the Syncrude oilsands mine in Fort MacMurray, Alberta, Canada. Monitoring of these covers for temperature, matric suction, and water content by the University of Saskatchewan has been ongoing for more than three years. The three covers (D1, D2, and D3) were constructed in 1999 and are 50 cm, 35 cm, and 100 cm thick. The covers are comprised of a surface layer of reclaimed peat/mineral mix over a secondary reclaimed mineral soil (glacial till or glaciolacustrine clay), placed over a sloping shale surface. Field measurements of hydraulic conductivity within the secondary layer were obtained using a Guelph Permeameter during the 2000, 2001, and 2002 summer field seasons. Repeated measurements were made within the D1, D2, and D3 covers at depths of approximately 40 cm, 30 cm, and 60 cm, respectively. The values of hydraulic conductivity for the covers were similar to each other during each of the field study seasons. The mean hydraulic conductivity of the secondary layer increased every year: 2.5 + 10-6 cm/sec to 2.1 + 10-4 cm/sec to 4.3 + 10-4 cm/sec from 2000 to 2001 to 2002. Soil temperature data shows that one freeze/thaw cycle occurred each year at the measurement depths.

Jan 1, 2003

By M Zoorabadi, Y Zhang, D Bringemeier, S Nicoll, N Kerr

Lihir operations of Newcrest Mining Limited (NML) are on Lihir Island (PNG) which is located approximately 900 km north-north-east of the national capital Port Moresby. The mine is located within the Luise Caldera of the Luise Volcano which is located on the east coast of the island. The caldera is an extinct volcanic crater that is geothermally active. Volcanic activity on Lihir Island is limited to remnant hydrothermal venting in the Luise Caldera in the form of hot springs and fumaroles. Steam and gas (including H2S) naturally discharge within the pit area and along the Kapit beach and near shore region. The hydrothermal reservoir temperatures can reach 100°C at the water table and exceed 200°C at depth. Newcrest maintains a Geo-hazard Management Plan to identify and manage the various geotechnical and geothermal hazards on-site. The major geothermal hazard to mining at Lihir is the occurrence of geothermal outbursts, which have occurred in the past with varying intensities and caused two ‘near misses’, production delays and material losses.

Nov 29, 2022

By L McCallum, G Dale, B Silverwood, T Roscoe, A Costin

The introduction of Progressive Closure and Rehabilitation Plans (PCRPs) in Queensland from 2019 places greater importance on planning and implementation of mine rehabilitation activities. The progress and outcomes of progressive rehabilitation activities is monitored and reported upon to demonstrate success in achieving progress towards the approved post-mining landform, and to inform corrective action where required. The requirements of PCRPs place additional emphasis on mine sites to quantify the risks of successfully achieving planned outcomes. This is particularly challenging given mined-land rehabilitation is a complex process involving decisions on multiple inter-acting management interventions, climatic conditions and spatially variable site characteristics.

Aug 2, 2023

By P Stewart, S Cowie, A Offer, J Carpenter, E Jones

The Ban Houayxai Gold-Silver Operation is a producing asset for Australian-based copper and gold producer, PanAust Limited. The Operation lies within PanAust’s 2600 square-kilometre Phu Bia Contract Area in northern Laos. Commencing production in 2012, Ban Houayxai is operated by PanAust’s Lao-registered company, Phu Bia Mining. PanAust owns a 90 per cent interest in Phu Bia Mining. The Government of Laos owns the remaining 10 per cent. The Operation mines an intermediate sulphidation epithermal gold-silver deposit and comprises an open-pit feeding ore to a conventional carbon-in-leach process plant. Metallurgical recoveries for gold and silver are approximately 75-85 per cent and 55 per cent respectively. To year-end 2017, the Operation had poured 0.65 million ounces (oz) of gold and 4.7 million oz of silver. The Ban Houayxai Ore Reserve supports a mine life of approximately four years from the end of 2017. The Ban Houayxai deposit is in an early Permian volcano-sedimentary unit which is part of a late Carboniferous to early Permian (310–270 million years ago) volcanic-plutonic sequence of the Truong Son Fold Belt. The deposit formed when hot saline (240–415°C, 2.7–13.0 weight per cent NaCl equivalent) fluids ascended from a geologically fertile island arc porphyry into overlying volcanics along a fault or faults in the early Permian (290–256 million years ago) (Manaka et al, 2014). CITATION: Carpenter, J, Cowie, S, Stewart, P, Jones E, and Offer, A, 2018. Machine learning at a gold-silver mine: a case study from the Ban Houayxai Gold-Silver Operation, in Proceedings Complex Orebodies Conference 2018, pp 82–85 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M Barden, G Lane, B Quilliam

NQ Minerals PLC, through Hellyer Gold Mines Pty Ltd, plans to reprocess the contents of the Hellyer tailings dam to produce lead/silver concentrate, zinc concentrate and pyrite concentrate (containing Au and Ag). This paper discusses the project development, mineralogy, metallurgy and chemistry of processing Hellyer tailings and the associated environmental benefits. The Hellyer and Fossey orebodies were volcanic hosted polymetallic massive sulphide deposits located within the Mount Read volcanic arc of western Tasmania. Mineralisation was hosted in massive sulphide (pyrite) and comprised predominantly of sphalerite, with lesser galena, chalcopyrite and arsenopyrite. The Hellyer orebody was mineralogically complex (fine grained) and was treated through differential flotation with initially modest recoveries. Fossey ore processing characteristics were similar to those of Que River ore and simpler than Hellyer but treatment still resulted in significant grades in flotation tailings. CITATION: Lane, G, Barden, M and Quilliam, B, 2018. Hellyer tailings – complex mineralogy but higher grade than many ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 35–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By C T. Senra, A Souza

Increasing fuel prices, unavailabilty and high prices of tyres have imposed tremendous challenges for large open pit operations. Carajßs open pit mines, one of the largest iron ore projects in the world, has been particularly affected due to the high amount of giant trucks operating in this site. On the other hand, environmental constraints push the mining industry towards reductions in fossil fuels, noise and waste generation. As a feasible response to these requirements, an alternative mining method for open pit mining, aiming to reduce or even eliminate the need for trucks has been developed, based primarily on coal opencast continuous operations. This innovative approach for open pits involves the replacement of trucks by fully-mobile crushers, bench conveyors and ramp conveyors. Two different applications have been developed for exploiting waste and ore at Carajßs largest pit, named N4E. To make it possible, mine planning paradigms should be replaced leading to new conceptual design of open pits. This paper shows two case studies (waste and ore conceptual design) carried out at Carajßs mines to anticipate and put forward the future of open pit mining, proving that our industry would be greatly affected by this new way of exploitation, reducing thousands of tons of fossil fuels. Productivities can be enhanced and environmental performance greatly improved. In this approach mine automation can be easily implemented reducing operating costs and man's fatigue.

Jan 1, 2009

By J Webb

The mining industry is relatively niche and complex compared to other global industries in its safety and operating environment. Whilst some of the technology required to decarbonise the mining industry will emerge from the mass market (eg batteries, energy storage solutions and renewable power generation) where exogeneous external investment and innovation will drive supply, bespoke applications such as material movement will be constrained by industry limitations. Underground load and haul equipment burns the majority portion of underground mine diesel, and typically 25 per cent of scope one and two emissions. Transitioning away from incumbent diesel engines offers a considerable health benefit to all mine workers, as well as decarbonisation achievements, and through trials there is emerging evidence of more productive equipment and realistic expectations of lower operating costs of fleet. However, new equipment and material movement systems that support these industry goals are currently approached with caution due to the pivotal role they play in delivering productivity goals, and the lack of experiential data and certainty to mitigate the supplier development risk during this technology transition period, where all resources are required to meet a booming industry. A group of mining companies and suppliers have the aligned aim to accelerate the understanding and availability of heavy haulage mobile equipment through collaboratively piloting equipment and working with suppliers and each other to aggregate market demand, encourage investment and resolve the mine design and technology choices through their involvement in the Electric Mine Consortium (EMC). This paper will outline the major challenges the industry must overcome in sourcing and adopting a zero-diesel particulate and zero-emission mine, drawn from cases and insights across ten EMC mining company members.

Mar 29, 2023

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

By Munive L

As a result of commissioning No.5 B F, 2670m3 inner volume, in March 1972, the largest B F in Australia; new expertise in maintenance, furnace operating practices and design have been obtained. This experience has also been extended to the other furnaces. A series of operating problems were con- fronted; all parts of the furnace, including the hearth side walls and bottom,were adversely affected. In December 1977, serious hearth wall wear was detected at No.5 B F, and a potential hearth breakout was averted. Hearth wear in No.4 B F was discovered in March 1979, and emer- gency underhearth cooling was installed to reverse an extremely advanced hearth bottom erosion. Hearth behaviour of No.5 B F oampaign 1972-1978 and`No.4 B F campaign commencing 1972, has been studied and discussions on the causes, effects and measures undertaken to protect the hearths are presented in this paper.

Jan 1, 1981

By Moylan T, Stewart D

A case study examining the procedures and financial benefits of introducing dump leaching to augment the Mt Gibson Gold Project CIP operations is discussed. Metallurgical testwork, followed by pilot dump leach operations, confirmed that gold recoveries of greater than 60 per cent could be achieved by dump leaching Mt Gibson laterite ore. Capital and operating costs were determined. Pit optimisation using the Whittle FOUR-D optimisation program calculated an optimum cutover grade between CIP and dump leaching for one orebody. The resultant recalculation of reserves based on CIP and dump leach operating costs showed that reserves for that orebody could be increased from 329 000 tonnes at 1.9 g/t An, to 1 488 000 tonnes at 1.2 gh An. NPV for the CIP only option of $1.4 m, was increased to $4.0 m for the combined CIP/dump leach option. This technique can be applied to existing gold projects and to new Developments.

Jan 1, 1992

The project is undertaken by Elgas Pty Ltd, a 50 per cent joint venture between AGL and BOC, to store 65 000 t of LPG in underground storage at Port Botany, NSW. The contractor, Concrete Constructions Pty Ltd, elected to use drilling and blasting techniques. The project specification called for the following works to be excavated: Access Shaft:122 m (out of 140 m total depth), 6.0 m diameter (selected by the contractor),Operation Shaft:125 m (out of 150 m total depth), 4.0 m diameter,Water Curtain Gallery:500 m (Later extended by additional 270 m), 4.0 m wide and 3.5 m high,Storage Caverns:910 m, 14.0 m wide, 11.0 m high,Top Heading:14.0 m wide, 5.5 m high,Bench:14.0 m wide, 5.5 m high,Connection Galleries:250 m, 5.5 m wide, 5.5 m high.A total of 156 000 cubm of rock to be excavated.

Jan 1, 1999

By E Giles

Pike River Coal Limited (PRCL) is opening a new underground coal mine in the Paparoa Ranges north-east of Greymouth. To access the coal reserves, PRCL have had to build a 13 km access road through regrowth and virgin forest, and appointed McConnell Dowell Constructors Limited, with URS New Zealand Limited as their consulting engineers, to construct the final access link: a 2.3 km long, 5.5 m wide and 4.5 m high incline tunnel. This paper discusses the logistical issues of construction in an isolated pristine forest in mountain land and how they were addressed. It provides an overview of the 90 per cent complete tunnel and how challenging rock conditions have been mastered. It outlines briefly the remaining work which is construction of pit bottom workings where the mine infrastructure will be housed and construction of a 110 m deep, 4.0 m diameter, vertical ventilation shaft.

Jan 1, 2008

A study of the bacterial oxidation of naturally occurring high-purity sulphide minerals (FeS2, Fel_xS, CuFeS2, Cu2S) has been conducted using a mesophilic strain of T. 6ejtAooLcdcth4. As well as metal analyses and solution pH, partitioning of sulphide sulphur into elemental sulphur and sulphate ion has been monitored. Partially oxidised sulphide substrates have been characterised at regular time intervals by X-ray diffraction methods and extra-cellular organic compounds reporting into leach solution have been identified by'thin layer chromatography. The results indicate that the S¦/SO4 2 partitioning of the sulphide substrates is independent of cell inoculum size and initial pulp density and varies with solution pH, Eh, leaching time and mineralogical properties of the individual sulphide minerals. The signifi- cance of results for applications in selective flotation, coal desulphurisation and agglomera- tion has been outlined.

Jan 1, 1984