Search Documents

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By C E. Woolley, H Jebaliya, J Foster

The East wall of the Kalgoorlie Consolidated Gold Mines Fimiston Open Pit (KCGM Superpit) has a history of wall instabilities impacting mining operations; the most significant of which occurred in May 2018, when more than 1 Mt of rock dislodged over six, 30 m high bench stacks and impacted the pit floor. Since 2011 approximately 1.250 Mt of material has fallen from the East wall at Fimiston Pit across three failure events (2011, 2018 and 2020). Each failure has been associated with major structures intersecting the pit walls: the Fiji Fault, the Australia East Secondary Splay Fault and the EWD3 Fault. In each instance the trigger for failure has been transient pore pressure in the pit walls. Northern Star will mine a cut back behind the failure area over a vertical distance of 180 m. Cut back mining will include the extraction of a remaining in situ wedge, which is assessed as kinematically able to fail, and a subvertical failure backscarp in Stage 1. A substantial amount of rill material from the 2018 and 2020 failures will be extracted in Stage 2. This paper presents the methodology in use to mine Stage 1 of the cut back, safely, through this potentially high-risk area, detailing the specific mining methodology employed, the controls put in place and the monitoring required. Day-to-day monitoring will be undertaken using the already installed slope stability radar and will feed into a daily assessment of activities which may be undertaken in the cut back area. Initial activities will focus on eliminating the potentially unstable wedge and vertical backscarp with use of innovative drill and blast techniques/products and the extensive use of remote capable equipment to limit personnel exposure.

Jun 22, 2022

By X Li, R Chu, X Deng

The hot-dip galvanising industry is the largest consumer of zinc, with over 40 per cent of the world’s total annual production of zinc used for galvanised steel. The dross generated in the hot-dip galvanising coating process is a valuable co-product, since it contains high quantities of recyclable metal. A new method to recover the metal from the industrial galvanising dross was proposed using supergravity separation. During the hot-dip galvanising process, the presence of zinc dross has a serious impact on the surface quality of the hot-dip galvanised sheet, forming zinc dross defects. To reduce the impact of zinc dross, the zinc dross on the surface of the zinc pool needs to be manually or mechanically removed at regular intervals. However, during the dross removal process, a large amount of metal zinc is inevitably carried out, resulting in low zinc utilisation rate and high zinc loss rate. This article proposes an efficient and low-cost technology for the recycling and utilisation of hotdip galvanised dross, which uses super-gravity technology to recover hot-dip galvanised dross online. The metal in the hot-dip galvanised dross returns to the zinc pot in situ, while a small part of the dross remains in the super-gravity equipment, which can reduce the amount of zinc dross by more than 60 per cent and achieve a reduction in zinc loss from 17 per cent to less than 7 per cent.

Jun 19, 2024

By J Carter, B J. Armstrong

Best practice for the submission of samples to an internal or commercial laboratory requires quality control materials to be included for the purpose of independently and comprehensively assessing laboratory performance. These quality controls include the use of certified reference materials (CRMs) and may be blind to the laboratory. Iron ore companies purchase these materials from reputable manufacturers from stock of run-of-mine materials at the appropriate grades. The international standard, ISO 17034 (ISO, 2016), specifies the competency requirements for organisations manufacturing reference materials, and includes rigorous requirements for the assessment of homogeneity, stability and establishment of property values and their uncertainties. Homogeneity is one of the most important measures of suitability for all certified reference materials and refers to the degree to which the composition and properties of a sample are uniform throughout the batch, relative to the analytical precision of the method. More specifically, homogeneity studies of candidate reference materials should be assessed for both within sample variance and between sample variance with appropriate statistical controls. The design and application of homogeneity studies are discussed as they apply to both crushed and pulverised reference materials. Crushed certified reference materials have been utilised by the iron ore industry for a number of years and provide the user with a critical assessment of variances in sample preparation in addition to analysis. Crushed reference materials are similar in presentation to an RC sample and are generally used as discrete parcels of material submitted to the laboratory from the field. Pulverise certified reference materials miss the sample preparation step and are subsampled from th delivered sachet at the point of analysis. This paper compares the relative homogeneity performance of crushed and pulverised certified reference materials by grade across key iron ore chemical constituents. Outcomes are benchmarked to the international standard ISO 9516 (ISO, 2003) for the determination of various elements in iron ores by lithium borate fusion and X-ray fluorescence. Practical implications are discussed with reference to a case study from an iron ore laboratory in the Pilbara.

Sep 18, 2023

By P Minkkinen, J Lohilahti, T Korpela, B McPherson

Concentrator plants intake the ore from the mine and produce concentrates by extracting valuable minerals in a succession of process steps. Controlling the extraction process and detecting changes in the process requires updated information on a minute basis. Moreover, due to economical reasons, one must also collect metallurgical samples on a daily basis for monthly reporting.In this paper, we present how slurry samplers were installed in a Cu-Ni flotation plant to accomplish the aforementioned tasks. An on-stream elemental analyser at the plant is used for flotation process control by taking samples from selected process streams. Two process streams, the flotation feed and tail, are also equipped with metallurgical samplers. The metallurgical samplers were designed to have low head loss, be robust and easy to maintain and to collect slurry samples in a reliable way for the metallurgical accounting.Samples were collected by different sampler types and we discuss the uncertainty arising from sampling in the assays. Variographic analysis was carried out on the process data in order to find periodic components in the process, and estimate the correct number of shift sample increments and measurement error components. The metallurgical samplers were proven to be reliable devices with zero downtime and no sanding issues in the main process flows. In addition, we show that the tail measurement is the most important one for the plant recovery calculation, which emphasises the importance of the sampling accuracy in the tail stream.CITATION:Lohilahti, J, Korpela, T, Minkkinen, P and McPherson, B, 2014. Analysis of slurry sampling arrangements at a froth flotation plant, in Proceedings Sampling 2014 , pp 91–98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By A Hacket, M Haest, I Vitins

Infrared spectroscopy has the ability to accurately measure mineralogy of drill cores, allowing for better spatial characterisation of iron ore deposits and potentially improving the prediction of key mining and processing parameters at the deposit scale. BHP Billiton Iron Ore is using infrared spectroscopic drill core logging to provide fast and accurate mineralogy for diamond cores and reverse circulation (RC) samples.Mineralogy can be predicted from infrared spectroscopic drill core data with errors on estimates ranging from six to 12 weight per cent. The error on the clay estimates is significantly lower than for hematite and goethite content estimates. This manuscript presents the results from a study on a bedded iron ore deposit, hosted in the Brockman iron formation, for which infrared spectroscopic data were collected on all of the diamond and RC drilling. Results show that these mineralogy estimates improve drill core logs, the geology model and the metallurgical block model.CITATION:Haest, M, Vitins, I and Hacket, A, 2013. Infrared spectroscopic drill core logging - making inroads to deposit scale 3D mineralogy, in Proceedings Iron Ore 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J Harris, P Kirsch, D Cliff, M Spinks, S Goater, D Sprott

Fires are a common and recurrent unwanted event in the operation of open pit mines. In most cases, the causes of events such as fires are already æknownÆ but are either overlooked or not fully addressed in planning. Ongoing rapid growth of the global mining industry is creating a scarcity of skilled personnel, and high turnover within operations. This contributes to loss of corporate memory in risk management activities. RISKGATE« is an online risk management system designed to support and assist in the analysis of priority unwanted events in Australian coal mining operations. Funded by the Australian Coal Association Research Program (ACARP), RISKGATE« is a knowledge management program that delivers best-practice controls for unwanted events and assists operations in staying abreast of emergent risks and threats. RISKGATE« content has been primarily developed from an association of industry experts, and enriched with input from additional academic and technological resources. In mining operations, RISKGATE« provides a continuum of knowledge and best practice for risk identification, assessment and management. RISKGATE« will assist companies in improving safety performance, operational efficiency, operating practice and training. Here we present the RISKGATE« prototype as developed in 2011 for Fires, with a case study presented for the initiating event Fires on Mobile Plant.CITATION:Harris, J, Sprott, D, Spinks, M, Cliff, D, Goater, S and Kirsch, P, 2012. RISKGATE« - A case study in application to fires on mobile plant, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 49-54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By D R. Wines

The design of near-surface civil infrastructure requires detailed consideration of the geological/ geotechnical conditions, excavation geometry and sequence and ground support measures to ensure stability of the underground openings and minimal impact on overlying or adjacent infrastructure. Twin parallel road tunnels have been designed and built with connecting cross passages and a piggyback busway tunnel as part of a large infrastructure project in Australia. The tunnels were excavated in poor to fair quality rocks using road headers. Temporary ground support includes shotcrete, rock bolts and canopy tubes. Extensive numerical analyses have been performed to analyse the expected behaviour of the tunnels during excavation, including two-dimensional analyses using UDEC and three-dimensional analyses using FLAC3D. Structural defects in the rock are explicitly included in the 2D analyses to examine the potential for localised ground instability. The stress redistribution is captured by the 3D modelling with an accurate representation of the complex excavation geometry and the detailed excavation and support sequence. This paper presents the modelling methodology, numerical results and discussions on integrating both 2D and 3D analyses to achieve reasonable design.

Mar 8, 2011

By A Grant, H Thomas, C Clarke, B Fuller

Native seed and plants are often a core input into the rehabilitation process of mine closure. Native plant establishment rate and performance is a function of many input elements including seed quality (purity and germination percentage), processing, treatment, storage, supply chain handling, application and ongoing management. Traditionally native seed has been supplied with very limited supporting information which in some cases has led to establishment failures, repeated attempts at successful plantings, and biosecurity issues, leading to increased rehabilitation costs for mining companies. Product procurement scrutiny, and sustainability credential requirements, in all supply chains is increasing the need for transparent, accurate, verified, and certified information. This collectively continues to evolve towards a social license to operate in all industries, including mining. The Australian Seeds Authority (ASA), in partnership with native seed supplier AustraHort, traceability software company Trust Provenance and supporting partners including Transport for NSW and Queensland Transport and Main Roads (TMR), were recipients of a DAWE National Traceability Grant. The project team has developed a framework and traceability software platform currently being piloted within the Australian native seed industry. The framework and platform allow for all critical-tracking-events along the journey of a native seed batch to be easily captured utilising a smart phone application (APP) and the global standard for data capture. The platform provides a unique identification for each batch of seed and critical tracking event. The batch ID belongs to that batch and all supply chain stakeholders can contribute to batch traceability by providing more information/data to increase information integrity. This gives the end user, and other stakeholders, increased levels of trust in the product to support value, increase efficiency and reduce costs. For mining companies these efficiencies and cost reductions are in the form of information availability across site/company, potentially improved vegetation establishment, less rework and efficient monitoring. Ultimately this contributes to safe, stable and sustainable rehabilitation. By capturing data on harvest, logistics, storage (including temperature and humidity), aggregation/blending, treatment, application and ongoing management, the native seed industry and end utilisers of native seed have a greater level of product integrity, brand integrity and information integrity.

Aug 2, 2023

By D Maldonado

BlueScope Steel’s Port Kembla sinter machine underwent a major upgrade during mid-2009. The mixing and rolling drum (MRD) was thoroughly cleaned during the upgrade. Space factor measurements taken in October 2009 showed that the drum was operating in the cataract regime in the dry mixing section and the cascading regime in the rolling section, which is optimal for granulation. Sampling carried out during an entry into the MRD showed that both the Sauter mean diameter and the predicted bed voidage increase rapidly during wetting, and then decrease in the wet mixing section. In the rolling section, the granule properties remained constant untilthe drum discharge. Frozen particle analysis, using liquid nitrogen as the quenching agent, were carried out on material collected from the MRD discharge. The results, expressed as a Granulation Index, showed there had been a significant improvement in the granulating performance of the MRD following the upgrade. The plant studies were also complemented with laboratory scale experiments which aimed to optimise the granulation process. The effect of burnt lime on green feed permeability was quantifi ed using the laboratory scale drum at different moisture contents. A significant increase in permeability was apparent once the burnt lime dosing rates doubled from 1.1 - 2.2 per cent w/w (feed basis). The capacity of the burnt lime system at the sinter machine will be increased in order to benefi t from the expected higher permeability, permeability, which will enable the machine to sinter at deeper bed heights.

Jul 11, 2011

By D Kilkenny

This paper discusses the use of a mechanised shaft sinking machine Herrenknecht Vertical Shaft Sinking Machine (VSM) – to conduct the 93 m presink for the Wira Hoisting Shaft at the Prominent Hill Mine in South Australia. This technology has been widely used in the global construction industry, however, this was the first time it had been used in Australia and the second time in a mining application. The non-entry shaft sinking system eliminates risks associated with a traditional manual method and allows all shaft construction operation to take place from surface. The geology in the upper 100 m at the Prominent Hill mine is conducive to mechanical excavation, with expected rock strengths below 130 MPa. This enabled an alternative shaft construction methodology to be considered. The Herrenknecht VSM system was selected due to its extensive work history and demonstrated performance in similar ground conditions. In collaboration with the operations and design team, the shaft collar and surface configuration were modified to suit the requirements of the VSM, additional equipment, and loading jacks that support the pre-cast lining. Dedicated concrete moulds were designed in Germany and built in Italy. The concrete segments were cast in Adelaide and road freighted to site. This paper outlines each stage of the presink – refurbishment, transportation, logistics, establishment, operation and demobilisation. Selecting this shaft presink excavation methodology, delivered through positive collaboration and communication despite some challenges, shows the benefit to the mining industry of applying new technology and innovation to improve safety and productivity.

Mar 29, 2023

By B Prasad, M P. Roy, P K. Singh, C Drebenstedt

Blasting operations play a pivotal role in the overall economics of opencast mines. The blasting subsystem affects all the other associated subsystems, ie loading, transport, crushing and milling operations. Fragmentation control through effective blast design and its effect on productivity is a challenging job for the practicing blasting engineer due to inadequate knowledge of actual explosive energy released in the borehole, effect of varying initiation practice in blast design and its effect on explosive energy release characteristic. This paper describes the result of a systematic study on the impact of blast design parameters on rock fragmentation at two mines in India. Both the mines use draglines and shovel-dumper combination for removal of overburden. Despite its pivotal role in controlling the overall economics of a mining operation, the expected blasting performance is often judged almost exclusively on the basis of poorly defined parameters such as powder factor and is often qualitative, which results in a very subjective assessment of blasting performance. Such an approach is a very poor substitute for accurate assessment of explosive and blasting performance. Forty-seven blasts were conducted with varying blast designs and charging patterns and their impact on the rock fragmentation are documented. A high-speed camera was deployed to record the detonation sequences of the blasts. The efficiency of the loading machines was also correlated with the mean fragment size obtained from the fragmentation analyses.CITATION:Singh, P K, Roy, M P, Drebenstedt, C and Prasad, B, 2015. Blast design parameters and their impact on rock fragmentation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 755–762 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C B. Smith, G L. Boxer, S W. Moss, A L. Jaques, V Lorenz, M J. Rayner

The Ernest Henry Iron Oxide Copper Gold deposit is hosted in a large dilation between two moderately dipping shear zones found in the footwall and hanging wall of the deposit. These shears are controlled by a large diorite intrusion to the north-east and south-west of the deposit, formed ~1660 Ma. A shear zone dubbed the ‘Interlens’ uncovered through underground workings truncates the main orebody into two lenses, and is hypothesized to have formed in conjunction with the Hanging Wall Shear Zone and Footwall Shear Zone. All three shears dip moderately to the SSE (50–140) from open cut exposures through to the current mining horizon approximately 800 m below the surface. Routine geological work and a capital drilling campaign has identified a significant flexure in these sub parallel ore bounding shears with increasing depth. A shift in shear orientation in the Interlens over approximately 100 m vertically from ~50° to the SSE to a steep, easterly trend (~85° to the east) is observed in both drill core and exposures in the underground workings. It is hypothesized the diorite intrusive to the south-west of the deposit controls the shear zone geometries at depth. The geometry of the Interlens mirrors the surface expression of the Proterozoic package of the orebounding shears to the south-west of the deposit, suggesting the surface geometries of the shear zones are consistent with depth. Additional drilling to explore the validity of this hypothesis is planned for the near future to better understand the structural controls on the Ernest Henry mineralisation with increasing depth.

Mar 22, 2022

By A E. Petts

Record iron ore prices and a renaissance of infrastructure in the Pilbara have Flinders Mines poised to move from explorer/developer to an iron ore producer. The potential of the company’s Pilbara Iron Ore Project was first highlighted by the announcement of Rio Tinto’s Caliwingina North deposit to the north and the Fortescue Metals group’s Serenity deposit in the southeast. The success of Flinders Mines’ exploration has been based on incorporating landscape studies into an existing geological framework, and using this to understand the iron-rich materials that were emplaced during the Tertiary. The development of the Delta and Eagle deposit resource models highlights this process. There are three main mineralisation styles at the project; detrital iron, channel iron and bedded iron deposits. They have textural and mineralogical similarities with comparative deposits in the region. Gaining an insight into the geological processes unique to detrital iron deposits and more distal channel iron deposits has been important to understanding the geometallurgy of the mineralisation. The model sits comfortably with other regional oregenesis models and allows a contextual framework to be developed around the timing of deposition of the Fe-rich detritus and pisolitic nodules that dominate the deposits. The exploration model also allows Flinders to explore more effectively for bedded iron mineralisation developed prior to, and since the development of the Tertiary weathering landscape.

Jul 11, 2011

The Australian Mineral Industry has to compete on world markets, so its mineral research has to be aware of overseas developments, it must be of world class, and it must utilise as many ideas as possible in order to solve those problems that uniquely affect Australian minerals processing. North American mineral and resource research may be taken as a guide to world government, industrial, contract, and entrepreneurial research trends and ideas. A number of interesting findings are noted that may guide Australian developments and strategies for the future, in minerals research and exploitation.

Jan 1, 1986

By M Singh, R C. Steinhaus, J J. Rust

Metallurgical process control systems in mineral plants often employ state-of-the-art monitoring analysers in an attempt to optimise plant operations and enhance mineral recoveries. These systems are unfortunately invariably fed by simplistic ‘sampling’ designs consisting of various in-stream methods or pressurised probes. These are unfortunate compromises and provide a false picture of what a mineral flotation or other process can achieve. The situation is further aggravated by some manufacturers using misleading marketing to suggest discrete cross-stream methods for metallurgical accounting and unreliable continuous in-stream off-takes for control sampling and that they are of synonymous integrity.Reliable, absolute or representative samples are often absent in many modern day concentrator plants, due to compromises around sample taking, particularly in terms of delineation and extraction errors and thus leading to sample bias. For more reliable information from online analysers we need a continuous, but much more reliable sample taken, than is current practice.Online analysers require a fully proportional and continuous supply of sample for effective process control, otherwise maximised or benchmark recoveries will be nothing but a pipe dream. Large discrete cross-stream samples from mechanically less reliable equipment cannot be used as feed to online analysers, as it will negatively impact real-time feedback and efficient process control.It is possible to build correct sampling systems that could do both process controls online and metallurgical accounting at the same time. Multotec Process Equipment (Pty) Limited, in close association with experienced sampling consultant Francis Pitard, have jointly patented a concept to achieve this and which is embodied in the design of the unique Rotating Cone® Sampler (International Patent Application No. PCT/IB2016/057464). This versatile unit for dry and wet applications has high division ratios via two-step sampling and division.A prototype was built and tested to validate the design and levels of precision achievable when employing the unit to split dry mineral fines or even certain foodstuffs.CITATION:Steinhaus, R C, Rust, J J and Singh, M, 2017. Does process control sampling always have to be a compromise?, in Proceedings Eighth World Conference on Sampling and Blending , pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By M Flis

The Razorback Iron Ore Project is a high tonnage, low-grade magnetite deposit that defines a new iron ore district in South Australia. Known since the 1960s, the deposit has come into its own as the iron hungry world demands not only larger tonnages, but higher grade and cleaner magnetite concentrate ores that counterbalance the increasingly dirty haematite ores that are coming into production.Razorback is hosted by the Neoproterozoic Braemar Iron Formation, a tillitic unit that is part of the Adelaidean Geosyncline sedimentary sequence. At Razorback, this formation forms the southern limb of the Pualco Syncline, dipping at 42° to the north and outcropping along a prominent ridge. The formation consists of a series of alternating bedded tillitic and interbedded magnetite units that represent cycles of glacial advances and retreats. Seven cycles, resulting in seven stratigraphic members, are recognised. Members B, D, and G are the thickest, at 30 - 70 m each, and are the target of current investigations. While the bedded magnetite has the highest iron content, typically 35 per cent Fe, the tillitic unit, at typically 26 per cent Fe, has similar iron content in the ground mass but is diluted by the inclusion of iron-poor granite and metasedimentary dropstones. The mineralisation forms a simple dipping tabular body with only minor faulting, folding and intrusives. Grades, thickness, dip, and outcropping geometry remain very consistent over kilometres of strike, presenting an excellent mining proposition.Razorback differentiates itself from other Australian magnetite projects in a number of important ways. It is not a banded iron formation (BIF); it will have low crushing and grinding costs; and it is located in an infrastructure-rich area close to open-access, high capacity rail, to a selection of ports and to gas, electricity, labour and engineering services. Royal Resources has announced an Inferred resource of 277 Mt @ 25.9 per cent Fe. The company is targeting a resource of 500 - 1000 Mt to support a 10 Mt per year concentrate production. Davis Tube Recovery work shows that the ore is capable of producing a concentrate of over 68 per cent Fe with very low deleterious elements. Metallurgical testing confi rms the ore is soft, and with near-zero initial stripping ratio the project will have a low opex. With access to existing critical infrastructure, capex will also be low, ensuring Razorback will be a highly competitive iron producer in this emergent mining district.

Jul 11, 2011

By R McCarthy, P Darvall

FerrAus Limited's Robertson Range and Davidson Creek iron ore projects are located on the far eastern margin of the Hamersley Province, approximately 100 km to the east of Newman, Western Australia. The deposits are primarily formed of bedded haematite-goethite-limonite mineralisation within the Marra Mamba Formation, comprising a total combined resource of 164 Mt at 58.6 per cent Fe. The deposits represent relatively new discoveries for the Hamersley Province. The potential for mineralisation at Robertson Range was identified by Rio Tinto Exploration in 2000, while Davidson Creek remained untested until 2007. One of the main reasons for this is that these deposits are almost exclusively concealed beneath Tertiary sediments and recent transported cover making them difficult targets for conventional, prospecting style exploration. Since commencing exploration in the project area, FerrAus has collected nearly 20 000 stations of gravity data within the Robertson Range and Davidson Creek project areas, with most of this data collected at a 50 100 m station spacing. Gravity has proven itself to be an effective technique at predicting the position of the target host stratigraphy and has been a key driver in the exploration for concealed iron ore deposits. However, there is not always a perfect correlation between the position of gravity anomalies and concealed ore. The response of deep haematite bodies may be masked by low-density cover rocks, while other dense lithologies may be the cause of gravity anomalies which appear similar to the Marra Mamba targets. Hence, effective use of the gravity data requires interpretation in a geologic context with an understanding of the capabilities and limitations of the technique.

Jan 1, 2009

By M Behrens

The Melbourne Main Sewer Replacement (MMSR) is a major urban infrastructure project involving approximately 2.3 km of tunnelling and construction works. The works extend from Docklands Precinct, on the southwest edge of the city, southwards to connect with the Hobsons Bay Main Sewer in Port Melbourne. The tunnel boring machine (TBM) tunnelled section of the works terminates at the Yarra River where the delta geology and alignment requirements precluded the use of underground tunnelling methods. The 132 m long river crossing works involve a cut-and-cover excavation within a staged fl ooded cofferdam construction to construct an immersed tube tunnel as an extension of the TBM works.This paper reports on the development of the staged construction method and highlights the geotechnical and structural design aspects involved in building a new sewer in the Yarra River to close the gap between the new TBM driven and pipe-jacked tunnels.

Mar 8, 2011

By P J. Howard, P Darvall, J H. Mainwaring

In less than a year, Atlas Iron’s Corunna Downs Project has moved from a new discovery to a substantial resource of high quality in an underexplored greenstone belt. Located approximately 170 km south-east of Port Hedland and 40 km south-west of Marble Bar, in the Pilbara Region of Western Australia, Atlas Iron Ltd (Atlas) has conducted extensive exploration work at Split Rock, Razorback, Runway and Shark Gully, consisting of geophysical surveying, field mapping, 464 reverse circulation and 16 diamond drill holes resulting in a current resource of 51 Mt at 57.3 per cent Fe (Atlas, 2014b).The Corunna Downs Project is interpreted to be hosted within the Cleaverville Formation of the Archaean Gorge Creek Group. Within the project area these rocks outcrop as subvertically dipping banded iron-formations (BIFs) and jaspilites, cherts, minor shales and meta-sediments forming a north–south trending plateau.Primary hematite-martite iron mineralisation is overprinted in the near surface environment by supergene goethite, and frequently capped with a thin laterite cover. The strongest enrichment areas have been discovered within topographic lows, proximal to fault zones, which coincide with a geophysical anolmaly. These characteristics were targeted, and the subsequent areas mapped in greater detail, allowing for efficient resource definition.Although first explored for iron in the late 1960s, it wasn’t until Atlas’ acquisition of the project in October 2012, that major strides were made to defining an economic resource. At present, Corunna Downs is Atlas’ best greenfields exploration discovery, both in terms of the potential scale of the resource and its blending capacity.The Corunna Downs prospect is emerging as a major new iron ore province in the Pilbara and includes 80 km of potential host stratigraphy. Corunna Downs sits strategically between Atlas’ Mt Webber and McPhee Creek tenements, and can play an important part in Atlas’ growth strategy as iron ore market conditions become more volatile and challenging.CITATION:Mainwaring, J H, Howard, P J and Darvall, P, 2015. Discovery of the Corunna Downs deposits, in Proceedings Iron Ore 2015, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015