Search Documents

By McDougall I, Claoue-Long J

A combination of high precision 40Ar/39Ar and U-Pb dating has been used to determine the age of hydrothermal minerals and host rocks in a number of Lachlan Fold Belt (LFB) gold deposits in New South Wales, Au4 ralii In particular, this investigation demonstrates that the UAr/ Ar technique of K-Ar dating can be used to determine the timing of mineralization in Palaeozoic systems.A close temporal link between mineralization and Late Ordovician to Early Silurian magmatism is indicated by the dating work. Hydrothermal sericite from the Goonumbla p8rph gy Cu deposit and Glendale Au prospect yieldsAt/ Ar step heating ages between 437.9 ¦ 1.1 and 441.2 ¦ 1.1 Ma (16), and4 minjrnum age of about 425 Ma has been obtained by Ar/ Ar dating of hydrothermal amphibole from the Browns Creek Au-Cu skarn deposit. Hydrothermal aluniI8 frog the Gidginbung epithermal Au deposit yields reset 44 Ar/ Ar ages of 401.0 ¦ 1.3 to 417.3 ¦ 1.3 Ma (16). U-Pb dating by ion microprobe on magmatic zircons from the vicinity of the Goonumbla and Gidginbung deposits gives ages of 438 ¦ 3.5 Ma (2 6), and 435 ¦ 2.5 Ma (2 (7) respectimly, W a minimum age of 435 Ma has been obtained by Ar/ Ar dating of magmatic phases from volcanic rocks adjacent to the Browns Creek skarn deposit. Magmatic episodes near the Sheahan-Grants gold skarnpost give ages of 479.2 ¦ 1.1 and 467.9 ¦ 4o1 by 'Ar/ 9Ar dating of magmatic amphibole. Most Ar/3yAr age spectra show the effects of partial Ar loss at between 360-420 Ma, probably due to heating caused by granitoid emplacement.The radiometric dating work in this paper suggests a restricted metallogenic epoch in the Late Ordovician-Early Silurian LFB, NSW, of similar duration to that found in the Andean margin and the western Pacific island arcs around the Pacific Rini.

Jan 1, 1990

The æMountain Camp reefÆ at Alford's mine, Wakamarina,Marlborough, had no recorded gold production although assays of 5 - 26 g/t were reported, but it did produce c. l000 kg of scheelite. The lode consists of a lower massive quartz layer, and upper, cm-banded, ribboned quartz layers, and has a very low sulphide content. Within the massive layer, relict early fine-grained mosaic quartz with idioblastic scheelite is surrounded by recrystallised granoblastic coarse-grained quartz with calcite and plagioclase, in which an original ribbon banding texture is mimiced by strings of tiny inclusions. In both the banded and massive layers, rounded quartz grains, created by cataclastic milling of grain margins and along syn-vein fractures, have been partially annealed within later quartz overgrowths. Late fibrous quartz and calcite fill brittle cross fractures.   Deformation events D1 and D2 are associated with mid-late Jurassic metamorphism of the Pelorus Group, D2 producing the main regional schistosity (S2, and the earliest scheelite. D3 is an extensional mylonitic shear event that formed the dominant schistosity in Alford's mine (S3). The quartz lode was emplaced within the mylonite by a series of individual dilation pulses (D4). The D5 event caused crenulation of the S3 mylonite, kink banding and chevron folding of the S2 schist and S3 mylonite, and reverse faulting, rodding and cross-fracturing with late fibrous quartz-calcite veining of the D4 quartz lode.   Fluid influxes during successive dilations of D4 fractures progressively caused recrystallisation of earlier quartz bands on the footwall, annealing and recrystallisation of quartz along milled crystal margins and fractures, and deposition of minor sulphides. There was thus a dynamic interplay between fault dilation, lode fracture, fluid influx, lode band deposition, and lode recrystallisation. Illite-Kfeldspar al ¦ 2 Ma (K/Ar), c.30 Ma after metamorphism.

Jan 1, 1996

By M Haest, O Dominguez, D Mittrup

Technological innovations and emerging analytical capabilities are transforming the way drill samples are analysed, with real-time mineralogical analysis made possible. In addition, new business/technical requirements are challenging long standing processes to incorporate more sources of information during planning in order to improve compliance to plan during mining and processing. Unfortunately, the new sources of information that are added do not always have adequate protocols in place to ensure quality data is collected.Spectral data covering the visible – near – short wave – midwave – longwave range are routinely collected by the Geoscience and Exploration department at BHP Billiton Iron Ore for accurate mineralogical identification. These data are used for geological interpretations (logging and modelling) and prediction of physical variables (metallurgical and geotechnical properties).This paper introduces how sampling and quality assurance / quality control concepts have been applied in the spectral data process. The described routine for sampling, data collection/management and reconciliation has been developed to track system precision and accurately and consistently ensure the data is of high quality before it is used across the mining chain.CITATION:Mittrup, D, Dominguez, O and Haest, M, 2017. A new approach to implement quality assurance and quality control to technological innovations – quality of spectral data capture and processes in the minerals industry, in Proceedings Eighth World Conference on Sampling and Blending , pp 265–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By M BSckstr÷m

Acid rock drainage (ARD), commonly found in vicinities of sulfidic mines, possess properties capable of widely affecting the surrounding environment by acidification and heavy metal pollution. In most ARD treatments, various alkaline sources are used to neutralise the acid produced. Utilisation of highly alkaline fly ashes instead of raw materials is a cost-effective alternative, which lately have become increasingly popular. In laboratory batch experiments, neutralising capacity of fly ash was studied during 20 days. ARD was added to the fly ash once a day, for each increment the liquid to solid ratio (L/S ratio) was increased. At an early stage of the experiment (day 6, L/S ratio 12), the concentration of barium in solution unexpectedly increased by a factor of 50 (from 200 to 10 000 ¦g+l-1). This high concentration also sustained the following two days (L/S ratios 14 and 16) before dropping to the original level. pH showed a slight increase during these observations (pH 12.4 - 12.7). The phenomenon was also observed in a parallel and identical series. In addition to barium, aluminium and strontium clearly increased in the same manner, however not as much as barium. Furthermore, concentrations of chromium and molybdenum noticeably decreased at these distinct L/S ratios (12, 14 and 16). The behaviour of barium and subsequently strontium, aluminium, chromium and molybdenum is only partially understood. The decrease of chromium and molybdenum is suggested to be due to incorporation into the interlayer regions of hydrocalumite (Ca4Al2(OH)12(OH)2+6H2O), replacing the hydroxide groups, which also explains the increase in pH. Moreover, the increase of barium, strontium and aluminium could be attributable to dissolution of the silicate mineral celsian (Ba,Sr(Al2Si2O8)). Alternatively, barium and strontium increase could be explained by dissolution of a Ba,Sr(SO4)-solid solution and aluminium increase by dissolution of hydrocalumite or ettringite.

Jan 1, 2008

By Y Peng, D J. Bradshaw, G Long

As copper reserves deepen, they are becoming increasingly less pure. Penalty elements such as arsenic, antimony and bismuth are occurring in increasing concentrations. Environmental issues with smelters are leading to increases in penalty rates for these elements such that some concentrates may become difficult to sell. Arsenic concentration in Rosebery copper concentrates during 2010 varied between 3000 and 8500 ppm. Arsenic levels above 5000 ppm can preclude import to some customer countries. Optical mineralogy has indicated that arsenic in Rosebery copper concentrates is most commonly associated with tennantite (Cu12As4S13) in solid solution with tetrahedrite (Cu12As4S13). In addition, silver reports to concentrate as freibergite (Cu12As4S13 ). A reduction in arsenic content will therefore lead to a concurrent reduction in the silver content.A literature review by Long, Peng and Bradshaw (2012) indicated that arsenic bearing minerals could be removed using potential controlled flotation. Some success in reducing the amount of arsenic had also been reported using either roasting or chemical depression using reagents such as lime and cyanide. Due to the location of the Rosebery concentrator adjacent to world heritage listed temperate rainforest, the use of a roaster or cyanide was immediately discounted. Lime is already used as a reagent in the Rosebery flow sheet, so could be considered as a potential arsenic depressant.In order to determine a method of separating out the high arsenic bearing minerals, two series of flotation tests were conducted. The first series investigated the effect of pulp potential on the recovery of copper, silver and arsenic minerals; a second series investigated the effect of pH, froth depth and regrind.CITATION:Long, G, Peng, Y and Bradshaw, D J, 2012. Production of a low arsenic copper concentrate at MMG Rosebery, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 347-354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By C McCracken, R Landers, B Hesse

Minnovare identified the potential to improve production drilling outcomes in underground long-hole stopes through the adaptation of new technology which was under ongoing development. An approach to Evolution Mining resulted in the companies agreeing to a collaborative agreement to further develop the technology for use on underground long-hole drilling equipment. During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing setup/alignment process was compared to the new technology system with the following observations: • Using the existing process only 20% of holes surveyed recorded toe points within the +/ 300mm (11.8in) tolerance blast-hole deviation. • The new technology was proven to limit rig setup/alignment error, reducing average blasthole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: • Stopes drilled using the new technology recorded 62.6% less average dilution. • This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). • With the system implemented as standard practice following results of the FY18 trial and continued success, overall dilution for full year FY19 showed continued reduction to 12% Evolution has continued use of the new technology at Cracow, where the improved accuracy has allowed the extraction of narrower stopes where drilling accuracy is critical. Evolution has also deployed the technology at the Mungari operation and has stipulated that the contractor use the technology at the Mt Carlton operation, which is currently under development. Future implementation of the Development Optimiser system should be verified by commencing additional trials to include a larger data base for validating the initial trial results.

Mar 15, 2021

By H Asche

The Melbourne Metro project has evolved from the Victorian Transport Plan. MM1 is the second major phase of the proposed separation of Melbourne’s radial railway system, creating a line that will operate independently across the metropolitan region. The central section will run beneath the inner suburbs and the central city. The initial project comprises nearly 8 km of twin bore tunnels, three cavern stations and two cut and cover stations, as well as a dive structure and connections with the existing rail system. This paper describes the development of the geological model, a modification of the rock mass classification system derived during the EastLink project and the influence of the geology on the design of the tunnels and stations for the Department of Transport’s business case.The majority of the tunnelling will be in the siltstone and sandstone bedrock. This material has been extensively folded, sheared and intersected by igneous intrusions. A revised rock mass classification system has been developed for the Melbourne Formation to assist in identifying the important engineering properties of the rock and to rationalise the support types required.The Metro’s tunnel alignment crosses the Yarra Delta deposits in the lower reaches of the Moonee Ponds Creek and again at the Yarra itself near Princes Bridge. These deposits vary in extent and thickness over very short distances. The investigation of these materials has been carried out using conventional drilling techniques in conjunction with sonic drilling methods.Over the central section of the Metro, the positions of the new station are determined largely by transport planning requirements and urban development opportunities. However, the stations, and the tunnels, have been the subject of studies, optimising exercises, and selection processes to arrive at the concept design. This paper describes the influence of the varied geology on the development of the design, and the identification and management of the risks in tunnelling under the centre of Melbourne.

Mar 8, 2011

By J W. Dong, Y M. Li, J L. Tian, Z H. Jiang

Electroslag remelting is widely used to produce various special steels, mainly because of its ability to provide high cleanliness and excellent homogeneity of ingot. Undoubtedly an optimal slag plays a key role in removing inclusions and enhancing the mechanical properties of a specific special steel. In order to improve the metallurgical performance of the slag in electroslag refining of die steel, a variety of slags have already been developed using traditional trial-and-error methods. Nonetheless, these slags may not be inherently optimal for the specific requirements of actual die steel refining processes. In this work, we have designed a CaF2-CaO-Al2O3-SiO2-MgO quinary slag system using genetic algorithms method aiming to remove the existing large size inclusions (D and Ds type) in high quality die steel. The comprehensive effects of five components (CaF2, CaO, Al2O3, SiO2 and MgO) were studied based on existing fundamental theory. The slag composition was screened considering the parameters such as melting point, electrical conductivity, calcium ion concentration, and appropriate viscosity etc. Furthermore, the candidate optimal slag was applied in the industrial production of die steel by electroslag remelting method. The detection results indicate that majority large inclusions (D and Ds type) have been successfully removed, showing significant advantage to traditional slags. This result has demonstrated the genetic method to be efficient and reliable. In addition, depending on the personalised demand of other steel and alloys, this method allows for the adjustment of the screening frameworks and processes to develop the candidate optimal slags. This method has not been reported previously in the field of electroslag composition design, and compared with the traditional trial-and-error method, the new method will save a lot of time and experimental costs.

Jun 19, 2024

By G Capes

A novel open stope design approach is presented that delivered improved performance in a mining area with poor ground conditions at the Olympic Dam mine. During 2019, a large open stope had an unplanned caving event resulting in the inability to extract the planned tonnes and subsequent sterilisation of nearby stopes. A design limitation was the lack of data and understanding around the alteration domain extents, the rock mass strength controls and limits, the failure modes controlling stope stability in the local area, and the use of conventional stope shapes. From the available data and failure observations, it was inferred that the dominant caving failure mode resulted from a blocky rock mass impacted by structure and alteration causing an unravelling failure mechanism. Numerical and empirical analyses were conducted to test this hypothesis and establish strength limits for design. The strength limits for the design were then used to provide a range of outcomes from which future stope design shapes such as chamfered backs could be selected. Three alternate chamfered geometries were selected to trial the innovative designs. The application of this methodology in 2020 resulted in overbreak reduction from >100 per cent in the initial caved stope to

Mar 29, 2023

By Krouse RH, Aleinikoff JN, Nokleberg WJ, Church SE, Newkirk SR

A belt of volcanogenic massive sulfide (VMS) deposits and occurrences extends for over 150 km along the southern margin of the Yukon-Tanana terrane in the eastern Alaska Range. The VMS bodies occur mainly in the Jarvis Creek Glacier subterrane (JCGS), one of the highest structural/ stratigraphic levels of the Yukon-Tanana terrane. The JCGS consists of a VMS--bearing metavolcanic rock member and a metasedimentary rock member. The VMS deposits and enclosing rocks exhibit two periods of regional metamorphism.From northwest to southeast, the major VMS districts are the Bonnifield, Hayes Glacier, McGinnis Glacier, and Delta districts. The Bonnifield, Hayes and McGinnis Glacier district sulfide bodies consist of pyrrhotite and lesser amounts of pyrite, chalcopyrite, with or without arsenopyrite, sphalerite and galena. The larger, 800 km Delta district deposits and occurrences contain variable amounts of pyrite and pyrrhotite and lesser amounts of primarily chalcopyrite, galena, sphalerite, and arsenopyrite.The sulfide accumulations are interpreted as Kuroko-like deposits that formed along the submarine volcanic part of a Devonian, continental-margin igneous arc. U-Pb isotopic data from zircons from the metavolcanic rocks indicate an age of about 370 Ma (Devonian). 207Pb/204Pb ratios for sulfides from the districts are similar and indicate lead was in part derived from first cycle sediments eroded largely from Precambrian crystalline rocks. 207Pb/204Pb ratios from feldspars in Devonian metavolcanic rocks are similar to those in sulfides, and indicate incorporation of radiogenic Precambrian lead into the Devonian magmas. A Precambrian crystalline source for quartz in metasedimentary rocks is indicated by 2.3 Ga old zircons. Common-lead isotope studies of igneous phenocrysts in metaigneous rocks and sulfides in volcanogenic massive sulfide deposits indicate a unique isotopic signature. The data permit an exotic origin of the Yukon-Tanana terrane with respect to North America.

Jan 1, 1990

Gekko Systems Pty Ltd have developed the Python Underground Processing Plant for the concentration of gold and sulfide ores. The Python plant has an established flow sheet including fine crushing, screening, gravity separation and flotation which aims to concentrate the valuable minerals (gold/sulfides). The aim of the plant is to achieve high valuable recovery into a mass yield of 10 - 30 per cent to reduce the amount of material that is needed to be taken to downstream processing. This paper examines the test work protocol for testing an ore to assess its suitability for the Python flow sheet. This paper will discuss the test methods employed to determine crushing requirements, continuous gravity recovery and flotation performance and how the results relate to Python design for the comminution, gravity and flotation circuits. Results from past test work will be discussed.

Aug 1, 2010

By Y Yang, J Skrypniuk

The Jinfeng mine is Sino Gold's flagship project and is the second largest gold mine in China. Sino Gold Limited (SGL) holds 82 per cent equity in the Sino-Foreign joint venture Sino Guizhou Jinfeng Mining Limited (SGJML) with a Chinese partner. Jinfeng is located in a relatively remote site in southwestern Guizhou province. The orebody is considered to be the largest known Carlin type deposit in China. Jinfeng Plant has the world's third largest BIOX« bacterial oxidation facilities (790 t/d), treating highly refractory concentrate generated from crushing, semi-autogenous grinding (SAG) and ball milling and bulk sulfide flotation operations. The Jinfeng Plant construction started in February 2005, commissioning was completed in April 2007, and commercial gold production was achieved in September 2007. This paper describes the successful operations of Jinfeng Plant over the last two years. The key events of the project development are described, from the project background and process design, through to the commissioning and achieving design mill throughput of 3600 t/d resulting 180 000 ounces of gold per year. Process aspects of the BIOX« and carbon-in-leach (CIL) operations over the last two years are discussed which illustrate a very high BIOX« oxidation rate (more that 97 per cent) and excellent CIL recovery (more than 96 per cent). The management of the Jinfeng plant CIL tailings detoxification and filtration is described, and Jinfeng has became the first BIOX« processing plant to have achieved dry stacking of detoxified and pressure filtered CIL tailings. Current efforts to recover cyanide from CIL detoxified solution and the achievement of a zero discharge site water balance are also introduced. Many improvement projects have been made over the last two years which have culminated in a 15 per cent increase in mill throughput over the design and BIOX« CIL recovery increasing from 92.5 per cent to 96 per cent. Significant operating cost reductions from lowered of acid, lime and cyanide usage through process modifications and technical innovations are discussed.

Jan 1, 2009

By M Spagnolo, M Ashley, D, L Reemeyer

PasmincoÆs Century Concentrator in North West Queensland commenced operations in November 1999. The nameplate production capacity of 500 000 tpa of zinc metal production in concentrate was achieved in August 2002. Completion of the production ramp up was successful due to the culmination of a number of initiatives throughout 2001 and 2002. Mine to mill interaction to understand and eliminate head grade related bottlenecks affecting Concentrator production and reduce feed variation. Grinding circuit process development û operating and process control strategies to improve stability and reduce grind size to support zinc recovery. Pumping upgrades to control spillage in ultrafine zinc flotation Low density zinc flotation strategy û to improve silica-sphalerite separation to improve zinc recovery while maintaining acceptable silica in final concentrate. Flotation circuit process development û froth crowders, froth cameras and reagent control strategies to improve primary zinc flotation performance. Review and implementation of longer campaigns between planned shutdowns to improve availability. Team reorganisation û to improve setting and implementation of metallurgical strategies. This paper describes these initiatives and their contribution in achieving the production target. It also notes the ball mill motor failures that delayed the successful achievement of the ramp up, and CenturyÆs response to minimise the production impact. The paper also outlines the capital improvement program that was implemented to improve zinc recovery to design 82.5 per cent recovery once the production rate had been achieved.

Jan 1, 2003

By M Bouare, C Holland, K N’Diaye

Two adjacent open pits in Mali hosted by deeply weathered saprolitic materials were mined consecutively over the course of approximately 12 months. During excavation, both pits experienced significant displacement and tension cracking as the result of deeper than expected depth of weathering coupled with relatively steep slope angles and significant groundwater. In response, geotechnical and operations teams overcame numerous monitoring challenges with prisms and radar to develop a simple and effective monitoring system coupled to a Trigger Action Response Plan (TARP) which enabled continued safe operations while reducing ore loss. Observations of previous slope performance of these two pits allowed for greater confidence in empirical failure runout calculations that was used to specify the standoff widths for the exclusion zones in the pit. Back analysis of the slope as-built performance after the first indications of slope distress was also conducted. The back analysis was used to confirm rock mass parameters for modelling while being utilised as a reality check for the stability analysis. The stability analysis indicated that leaving a large step-out or buttress would not prevent the displacement, resulting in some ore being sacrificed to ensure the safety of personnel. Key learnings from this experience highlight the importance of: • up-to-date geological interpretation of the depth of weathering • ensuring slope design guidance is reviewed and updated as latest information (ie geology and monitoring) is received • having multiple complementary slope monitoring methods to ensure redundancy • ensuring visual observations and as-built performance are utilised as a reality check to provide greater confidence in stability analysis and design guidance.

Jun 22, 2022

By Daniels E. J, Morgan W. A

In response to the increase in consumption of galvanised steel for automobiles in the last decade and the problems associated with remelting larger quantities of galvanised steel scrap, a process is being developed to separate and recover the steel and zinc from galvanised ferrous scrap. The zinc is dissolved from the scrap in hot caustic using anodic assistance and is recovered electrolytically as dendritic powder. The dezinced ferrous scrap is rinsed and used directly. The process is effective for zinc, lead, and aluminum removal on loose and baled scrap and on all types of galvanised steel. The process has been pilot tested for batch treatment of 900 tonnes of mostly baled scrap. A pilot plant to treat continuously loose scrap, with a design capacity of 48 000 tonnes annually, has been in operation in East Chicago, Indiana since early in 1993. The first 450 t of scrap degalvanised in the pilot plant have residual zinc below 0.01 per cent and sodium dragout below 0.01 per cent. Use of degalvanised steel scrap decreases raw materials, environmental compliance costs, and opportunity costs to steel- and iron-makers. Availability of clean degalvanised scrap may enable integrated steel producers to recycle furnace dusts to the sinter plant and EAF shops to produce flat products without the use of high quality scrap alternatives such as DRI, pig iron, or iron carbide. Recycling the components of galvanised steel scrap saves primary energy, decreases zinc imports, and adds value to the scrap. The quantities of zinc available by the year 2000 from prompt and obsolete automotive scrap will approach 25 per cent of zinc consumed in the major automotive production centres of the world. Zinc recycling from galvanised steel scrap, either before or after scrap melting, will have to be Implemented.

Jan 1, 1993

By E K. Chiw, S-M Jung, S M. Masuka, ika

The world reserves of high-grade iron ore have depleted necessitating the need to utilise any existing natural iron ore deposits to meet the demands of the world’s expanding economy using hydrogen in the reduction process to curb CO2 emission. These low-grade ores include iron ores with high phosphorus content. The thermodynamic conditions in the blast furnace allow for the reduction of phosphorus that readily dissolves into the molten iron. Phosphorus in the gaseous state readily dissolves into the molten iron and therefore must be removed due to its negative influence on the mechanical properties of steel. The removal of phosphorus from molten iron is difficult causing the phosphorus to concentrate in metallic iron. The aim of this study is to provide basic knowledge on the phosphorus distribution after reduction using the CO-H2 and possibly provide the optimum conditions for phosphorus partitioning into slag, increasing the probability of its removal by magnetic separation. Total porosity, pore size distribution and surface area of the pellets used were measured using a mercury pressure porosimeter. The reduction was carried out using thermogravimetric analyses (TGA). The reduction rate increased with increasing H2 and was highest when 100 per cent H2 was used. Metal elements distribution in the reduced pellet was clarified using electron probe microanalysis (EPMA) and showed that phosphorus was distributed in the same areas as Ca. More phosphorus was concentrated in slag when 50 per cent CO–50 per cent H2 was used, increasing the probability of dephosphorization using magnetic separation. The concentration of phosphorus into slag was related to the rate of reduction. Further investigations into the reduction kinetics of this ore by CO-H2 is suggested to validate these findings. Nevertheless, a comprehensive thermodynamic analysis of the reduction of phosphorus containing phases found in iron ore with carbon, CO and H2 was provided to assist in selecting the optimal reduction experimental conditions.

Sep 18, 2023

By Fabjanczyk M. W

Artificial ground support has developed into a refined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bolt is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By M Haest, O Dominguez, D Mittrup

With the current focus in the mining industry on reducing costs, while simultaneously improving ore quality, infrared spectroscopy is a tool that can potentially assist companies to meet both challenges. Changes in the nature of infrared spectra are strongly influenced by changes in mineralogy, which is a key input variable for exploration (geology and orebody modelling and ore characterisation) and mining (pit design, mine scheduling and processing plant design/management).Infrared spectroscopic logging of drill holes has been embedded as a standard tool in BHP Billiton Iron Ore exploration, with a process set up to automatically deliver mineralogy and associated imagery to the end users (typically exploration geologists). The availability of consistent and automated mineralogy drill hole logs across a project is improving the output quality and reducing re-work.BHP Billiton Iron Ore is now looking into using the same infrared spectroscopic data for other applications, including improving predictions of geometallurgical and geotechnical parameters. Trials show that addition of infrared spectroscopic data to conventional data sets (element analysis and depth information) is significantly improving the accuracy of regression models to predict the lump-fine ratio.Further initiatives around infrared spectroscopic data in BHP Billiton Iron Ore include the installation of infrared spectroscopic sensors over conveyor belts, infrared spectroscopic mine face scanning and infrared spectroscopic blasthole logging. The ultimate vision is to have consistent, seamless mineralogical data from infrared spectroscopic sensing available throughout the mineral value chain (exploration/mining/processing). This seamless infrared spectroscopic data ‘bridge’ will allow the transfer of knowledge between the different sections of the value chain (exploration, mining and processing). For example, ore handle-ability could be predicted on exploration samples using regression models built from processing plant observations. In the opposite direction, information gathered about the buried stratigraphy by infrared spectroscopy utilised during exploration, could be used to predict the stratigraphy encountered during mining. This collaboration across BHP Billiton Iron Ore is expected to deliver significant savings, while improving the quality of the final product, thus helping to drive efficiency over the next decade.CITATION:Haest, M, Mittrup, D and Dominguez, O, 2015. Reaping the first fruits – infrared spectroscopy: the new standard tool in BHP Billiton Iron Ore Exploration, in Proceedings Iron Ore 2015, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M Andrew, H Reynolds, R Mills

As the global mining industry continues to grapple with ‘black swans’ (high consequence / low frequency events) for health, safety and environmental losses, the focus is shifting from risk assessment of these events to risk management using selected purposeful controls that reduce the risk.Fundamental to critical control management (CCM) is a soundly based rationale for selecting the right controls for each and every risk. The approach should be based on a thorough understanding of the dynamics of the event: What causes it? How frequently will it occur? How likely is the consequence to be realised? This is typically done through a bowtie and methodical numerical risk analysis. Core to this step, then, is the structure and content of the bowtie; specifically, the analytic architecture that is used to construct the bowtie. Different architectures yield different constructions, and bowties are no different.Although bowties for operational health and safety (OHS) hazards appear to have a common architecture, they are not generic. It is important to stress that they contain site specific information, are prepared by site based operational teams, and vary from site to site to reflect each site’s operational conditions. They are often a product of the knowledge and understanding of the operational teams involved, may be prone to human error, and potentially miss latent hazards that may have been embedded early in the planning, design or construction phase of a mine or facility, or within the mining equipment. Overcoming these deficiencies through constant re-evaluation of the risks, and challenging the content on the bowtie will help to minimise the chance that something will be missed.This paper will cover key themes in bowtie architecture, introduce the concept of barrier models for high consequence event (HCE) bowties and present a relevant case study to illustrate the issues that determine quality in bowtie construction and critical control (barrier) selection and management.CITATION:Mills, R, Andrew, M and Reynolds, H, 2016. Can we stop a black swan breeding? Advances in bowties and critical control management, in Proceedings International Mine Management Conference, pp 105-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By R Knight

The spatial variability of geometallurgical characteristics in a mineral deposit can have significant impact on financial and mine planning, mineral processing, concentrate quality and tailings composition throughout the life of a project. These characteristics that may determine the success of a project are not readily apparent to geologists unless they are integrated with deposit geology and assay data, modelled in 3D and incorporated into resource block models.One of the primary objectives of geometallurgy is to integrate and incorporate various geologic, geotechnical and geometallurgical parameters into resource block models, which typically are limited to in situ tonnes and grade of economic metals. Critical attributes, such as concentration of deleterious elements that affect the project viability need to be identified and integrated into the resource block model early in the exploration stage to predict project profitability and address potential environmental impacts.Using data from a volcanogenic massive sulfide deposit we present an example of the integration of ore geochemistry (cadmium, arsenic and antimony) with the results of preliminary, bench-scale metallurgical test work in a 3D geometallurgical model that predicts subdomains of poor-quality concentrate and tailings containing environmentally-sensitive elements. This critical information was incorporated into the existing resource block model in order to inform both financial modelling and mine planning.This example demonstrates that geometallurgical data can be effectively integrated with geological and assay data using Leapfrog MiningTM software (Leapfrog Mining) early in the exploration stage of a project. Three-dimensional representations of geometallurgical data can be created directly using primary additive data, as well as from proxies of non-additive parameters. Resource block models can be updated continually with new information as the project passes from exploration through production. In addition, the software allows for 3D visualisation of the characteristics of the materials that will eventually constitute the mill concentrate, tailings, and waste. This study emphasises the critical importance of establishing a systematic geometallurgical approach early in the exploration stage that can be continuously updated with new information throughout the life of the project. In the example that we present, sulfide ore that had otherwise been identified as high-value (in the absence of geochemical and metallurgical data) turns out to be low-value ore due to concentrate penalties and increased environmental impact.

Sep 5, 2011