Search Documents

By T Honeyands, L Jelenich

We are currently witnessing large fluctuations in the relative price of ironmaking raw materials brought on by changes in the dynamics of supply and demand, market conditions, environmental regulations and technical factors affecting the iron and steelmaking process. From a customer perspective, it is the behaviour of iron ores in downstream processing that give them their value; their impact on the sintering or pelletising process and subsequently blast furnace ironmaking. It is therefore important to consider this value when developing projects, making mine planning/cut-off grade decisions and in setting price differentials for differing quality.This paper describes the use of the Marx value-in-use model to quantify the downstream value of lump iron ores. The Marx model consists of heat and mass balance modules for sintering and pelletising and a rigorous two-stage heat and mass balance model of blast furnace ironmaking. Mass balance and cost models are applied for steelmaking, casting and rolling. The use of a heat and mass balance allows accurate comparison of the impact of raw material properties on blast furnace operation. The impact of minor elements, such as alumina, silica and phosphorus, and metallurgical properties on ironmaking is described, and examples are given for the calculation of a lump premium.CITATION:Honeyands, T and Jelenich, L, 2015. Lump ore properties and their impact on value-in-use in ironmaking, in Proceedings Iron Ore 2015, pp 359–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A K. Raina, V M. S R Murthy

Rock mass response in blasting is an important element to determine the performance of a blast along with its other outcomes. The near-field monitoring for rock mass response analysis is vital for determining the behaviour of a blast; however, due to costly and cumbersome methods involved in such measurements the subject has received scant attention so far and the publications on this account are perfunctory in nature. This paper presents a non-destructive method to monitor the blast-induced pressure in the rock mass at a distance from a blasthole. The methodology of monitoring and a few examples of actual field monitoring are detailed in this paper. The responses of the rock in the near-field of a blasthole under dynamic loading have been documented to predict fragmentation and throw. The proposed method has also been used in limited cases earlier by the author to predict flyrock using a semi-empirical method and trajectory equation. The pros and cons of the method are discussed while throwing light on the actual response and the prediction of fragmentation and throw of blasted rock.CITATION:Raina, A K and Murthy, V M S R, 2015. Measurement of blast-induced pressure in bench blasting and deciphering explosive performance through rock mass response analysis – a methodology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 501–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Lalor, N Goodman

The increasing demand for batteries is resulting in the development of large-scale projects for the production of key battery metals such as nickel and vanadium. Several of these projects plan to extract the battery metals from the ore via chemical roasting, leaving large volumes of waste iron oxides after fuming and/or leaching of the battery metals. These iron oxide wastes can be smelted in a HIsmelt furnace using biochar as the reductant, to produce clean, green pig iron with net zero carbon emissions. This green pig iron can then be added to basic oxygen or electric arc steelmaking furnaces to produce green, net zero carbon, steel. This paper describes the flow sheets and the economics for potential projects producing green pig iron via HIsmelt using waste iron oxides from nickel and vanadium production plants.

Sep 18, 2023

By M J. Nugus, J G. McLellan, T G. Blenkinsop

High fluid pressures and deformation have been instrumental in the formation of high-grade gold lodes at the Archaean granite greenstone 12 Moz Sunrise Dam gold deposit in Western Australia. Historically, predicting the location of these lodes has been difficult due to the irregular nature and high-grade nugget characteristics of the deposit. Recent exploration successes and the discovery of the Vogue system have led to an improved knowledge of the deep extents of the mine. This new structural and gold distribution data has enabled a new 3D interpretation of the system and has provided a better insight into the links between deformation, fluid pressure evolution and gold deposition. Here we employ 3D geomechanical and coupled fluid flow modelling to better constrain areas of high strain partitioning, rheological failure and focused fluid flow, which provides a substantially increased predictive capacity for further within-mine exploration. The localisation of deformation in and around the main felsic porphyry and major shallow shear zones provides critical insights into fluid pathways that have contributed to the distribution of fracture networks and ultimately gold deposition during late stage deformation events. Understanding the relationship between deformation events, fluid pressure evolution and the partitioning of strain is paramount in understanding the distribution of gold and for focusing on future target areas.CITATION:McLellan, J G, Blenkinsop, T G and Nugus, M J, 2013. Fluid pressure, geomechanical evolution and predictive targeting of the Sunrise Dam gold deposit, Western Australia, in Proceedings World Gold 2013 , pp 419-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

At Bulong, the mineralised (>0.8 per cent nickel) ore exists within numerous lithologies, which can and do occur coincidently. It is very important to discriminate between the different host units for estimation purposes, stockpiling and scheduling. This allocation of host unit has relied upon visual interpretation by the geologist recording the information, which can be very subjective by its nature. By using quantified constraints, such as assayed magnesium oxide and iron, the subjectivity of describing the host material of nickel laterite ore is reduced. The constraints permit consistent identification of the various host units, which improves the confidence in the overall estimation and scheduling of the ore.

Jan 1, 2000

By R Dwyer

Iron ore currently mined in Australia generally requires very little beneficiation. However, depleting high-grade resources means that in the future low-grade iron ore deposits will need to be mined to meet the increasing demands of the global steel industry. Along with the increased demand, the industry faces additional pressure to reduce the environmental impact of mining and mineral processing. This has stimulated research beyond incremental improvements to conventional processing into alternative low-impact processes, including biotechnological approaches to mineral processing.Bioflotation and bioflocculation have emerged as relatively recent technologies, in which bacteria and/or their extracellular material may be used as flotation reagents (collectors or modifiers), enabling improved selective separation of minerals. The primary advantage is the production of a selective, environmentally-benign alternative to conventional flotation reagents. A biotechnological approach may also be taken in the beneficiation of high-phosphorous iron ores utilising bacteria capable of iron reduction and phosphorous solubilisation.Samples from three iron ore deposits in Western Australia were examined for bacteria suitable for iron ore benefi ciation. A number of common soil microorganisms including Pseudomonas spp, Limnobacter thiooxidans, Paenibacillus spp, and Ralstonia insidiosa were identified using culture-independent molecular techniques. A number of anaerobic species belonging to the genus Clostridium were also identified in the core samples. Selected aerobic species were enriched and isolated on high nutrient media in the presence of haematite. Several of the isolated strains showed an affinity for iron ore, attaching to haematite in enrichment cultures and further demonstrated through adhesion studies. Other isolated species such as Ralstonia isidiosa and Pseudomonas stutzeri are known to solubilise rock phosphates in soils and have potential for the removal of phosphorous from Australian iron ores.

Jul 11, 2011

By C Rule

In 2003, Anglo Platinum, in a joint development with Xstrata Technology, installed the world’s first 10 000 litre IsaMillTM in a concentrate regrind duty at the Western Limb Tailings Re-treatment Plant. The success of that installation was the enabling event for Anglo Platinum to proceed with a substantial investment in horizontal stirred milling technology. Since 2006 an additional three IsaMillsTM in concentrate regrind duties and a further 18 IsaMillsTM in the more technically challenging coarse grinding mainstream applications, have been commissioned in group Concentrator operations - bringing the total number of IsaMillsTM installed in Anglo Platinum plants to 22.A collaborative approach between Anglo Platinum and Xstrata Technology towards improving milling efficiency and reducing operating costs, through internal mill component wear optimization and operating recipe development, has resulted in further improvements in the overall success of IsaMillsTM in the flow sheets of many Anglo Platinum operations. The addition of IsaMillsTM in the Anglo Platinum flow sheets has improved plant PGM recoveries by as much as 5%.This paper explores the improvements made to the IsaMillsTM flow sheet and mill internal design and shares some of the operating experience with IsaMillsTM technology in Anglo Platinum

Aug 8, 2011

By R Valenta, I Fahey, M Klawitter, N Spanswick

Zinc-Lead-Silver (Zn-Pb-Ag) mineralisation at the George Fisher Mine occurs in multiple structurally-disrupted stratiform orebodies hosted within a mid-Proterozoic sequence of calcareous siltstones and variably pyritic shales (e.g. Valenta, 1994; Chapman, 2004). The geological model for the mine has been constructed based on a large number of stratigraphic domains which have been defined using recognised patterns of the constituent rocktypes, aided by recognition and mapping of K-rich tuff marker beds (TMBs). The continuity of these domains has been affected by the presence of several sets of faults which are extensional in the plane of stratigraphy, leading to the common occurrence of fault-related stratigraphic gaps in drillholes. Recent improvements to the detail of the geological model have led to significant improvements in the head grade of ore at George Fisher, with relatively small loss of metal. Recognition and accurate logging of these domains requires a high level of knowledge and expertise amongst mine geologists. In order to aid this process, the George Fisher mine installed a Minalyzer CS (core scanner) on site, with the aim of using high resolution X-ray fluorescence (XRF) geochemical data and core photography to increase the speed, accuracy and consistency of the site geological logging system. This contribution describes some preliminary results from a research project aimed at using the Minalyzer CS XRF data to perform high-resolution rocktype identification and domain boundary mapping in drillcore at George Fisher. CITATION: Spanswick, N, Klawitter, M, Valenta, R and Fahey, I, 2018. Rocktype classification and domaining of complex stratiform Zn-Pb-Ag mineralisation at the George Fisher Mine using high resolution XRF Core scanning, in Proceedings Complex Orebodies Conference 2018, pp 58–59 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By S Ellis

In January 2008 Chirano Gold Mines Limited committed to expansion of the Chirano Gold Project from its existing design capacity of 2 Mtpa ROM ore to a new design value of 3.5 Mtpa. In addition to increased throughput, the design had to contend with increasing ore hardness and competency, while at the same time make cost effective use of existing equipment with minimum disruption to existing production. The solution adopted involved some novel approaches including tertiary crushing and operation of the SABC circuit in overflow ball mill mode and parallel elution with a common acid wash column. This paper describes the approach taken to the design of these elements to achieve a cost effective and safe capacity expansion.

Aug 8, 2011

By J Isles, S King, A Valenza, R Lawolo, J Evert

PT Nusa Halmahera Minerals (PT NHM) is an Indonesian joint venture company owned by a subsidiary of Newcrest Mining Limited (75 per cent) and PT Aneka Tambang (Persero) (25 per cent). PT NHM operates two underground gold mines, Kencana and Toguraci at the Gosowong mine site in North Halmahera District, North Maluku Province, Indonesia.The Toguraci underground mine development commenced in 2011 with ore production commencing in 2012. Water temperatures ranging from 50°C to 80°C were encountered in the Toguraci open pit associated with the structures containing the gold bearing veins and are believed to be fed from a relic volcanic system one to two kilometres below the mine. Underground development and production has continued to intersect these structures with the result that an integrated programme of geological, hydrogeological modelling and operational project work has been required to dewater the mine ahead of the descending stoping fronts.This paper will detail these programmes.CITATION:Lawolo, R, Isles, J, Evert, J, Valenza, A and King, S, 2017. Hot water management at PT Nusa Halmahera Minerals’ Toguraci Mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Y Xu, J Hacker, D J. Williams

Shear strength parameters of compacted clay liners are needed to analyse the stability of mine waste dumps containing compacted clay liners as sealing layers for potentially acid forming waste rock. A representative clay sample was supplied by McArthur River Mine from the mine site in the Northern Territory, Australia, with an average as-supplied gravimetric moisture content of about 13.6%. The clay was compacted in a 100 mm by 100 mm direct shear box at the as-supplied moisture content to a dry density of 1.85 t/m3, representing the field compaction specification adopted by the mine. To determine the peak and ultimate shear strengths of the compacted clay, single-stage direct shear testing was carried out at nominal initial normal stresses of 50 kPa, 100 kPa and 200 kPa, representing shallow depths of burial in the North Overburden Emplacement Facility of about 2.8 m, 5.6 m and 11.1 m, respectively (assuming a waste rock wet unit weight of 18 kN/m3). Three shearing rates of 1 mm/min (rapid), 0.1 mm/min (intermediate) and 0.01 mm/min (slow) were applied to study the influence of shearing rate on shear strength. In addition, the development of a residual shear plane was tested by reversal and re-shearing in the direct shear box. In the first shearing, the peak and ultimate shear strengths are determined. The normal load was then removed and the box rewound to its starting position. The normal load was then re-applied and the specimen re-sheared. Two reversals were applied to each specimen, and it was found that there was no significant reduction in shear strength. Finally, based on a range of shear strengths obtained in the laboratory for McArthur River Mine clay and other materials by various laboratories over time, shear strength parameters for the compacted clay were recommended for use by the mine.CITATION:Xu, Y, Williams, D J and Hacker, J, 2018. Shear strength of compacted clay liner at McArthur River Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 208–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By G B. Ebsworth, J Krokowski de Vickerod

Several drilling programs at Maldon have produced 7790 core samples, which were assayed for gold, with 2825 of the samples assayed for nine other metallic elements. There is a lack of correlation between gold and all other elements. The situation, however, changes dramatically when sorted according to the abundance of arsenic. In the populations where As >200 ppm, there are strong, positive correlations between gold and several elements. There is also a strong positive correlation of Au with the weighted sums and products of all elements with the elemental averages as a weighting factor, and Bi*Sb and Bi*As elemental products. In these populations, there is also a strong positive correlation between the logarithms of Au and logarithms of each element, as well as the elemental sums and products described above. The correlation coefficients increase with higher As cut-off values.All elemental distributions but especially gold show a high-nugget effect and display high skewness and dispersion, low kurtosis, and common outliers. The distributions of their logarithms are several magnitudes less scattered and without outliers. Thus, the logarithmical distribution correlations are best for practical use.Correlation coefficients were T-tested and are statistically significant. The elemental correlations, particularly those of logarithmic values of weighted sums and Bi, could be used as a gold path finding tool at Maldon. After a preliminary assay for gold and arsenic, only samples with As > 200 ppm should be assayed for other elements. Higher values of gold-correlated elements or elemental ratios, in samples with low gold grades, may increase confidence that gold is under reporting due to its highly nuggetty nature.CITATION:Krokowski de Vickerod, J and Ebsworth, G B, 2012. Correlation as a gold path finding tool at Maldon, Victoria, in Proceedings Narrow Vein Mining 2012 , pp 131-144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By A K. Ghosh, J Chung, E Topal, M Asad

"Many open pit (OP) mines with considerable vertical extent are approaching the end of their life-of-mine; some of them are seeking the opportunity to make the transition from OP to underground (UG) mining. The decision on the best location for transition from OP to UG mining should be addressed at the strategic mine planning stage. Conservatively, the transition to UG mining is considered near or after the exhaustion of the reserve within the ultimate pit.However, if UG is evident and exclusively viable from the inception, defining the best location for the transition through a conservative approach may not be an optimal option to explore. This clearly establishes the need for a mathematical model that aims to maximise the project value and considers OP and UG mining with crown pillar (CP) requirement simultaneously. Underground mine layout varies from one UG mining method to the other, and consequently the variation in the location of transition is eminent. Thus, focus on the selection of UG mining method must be a part of this analysisThis paper presents an implementation of an integer programming (IP) based mathematical model that evaluates the changes in mining layout and the project value under possible variation in the transition point from OP to UG mining for stoping and block caving methods. An IP problem is a mathematical optimisation or feasibility method in which some or all of the variables are restricted to be integers. The outcome of the implementation reflects that mining strategies with OP transition to stoping and block caving methods generated higher values than OP-only mining strategy. The case study not only demonstrates the difference in mining layout for both stoping method and block caving method, but also reflects that a joint consideration of OP mining, UG mining and CP placement helps to achieve maximum project value and resource utilisation.Citation:Darbritz, J, 2016. Remediation of Wall Failure at Kalgoorlie Consolidated Gold Mines' Golden Pike Cut-back 2016, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 96–103 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By T Y. Dube

In this paper current net present value (NPV) based mine valuation techniques that take into account market and private risk are discussed and analysed. Potential pitfalls that arise from the application of a portfolio, market or commodity based risk metric to a mining project are identified. An alternative non-simulative framework for quantifying and factoring market and private risk in NPV calculations is proposed and then applied to a hypothetical case study in an attempt to overcome identified pitfalls. Mathematical proof that a static discounted cash flow (DCF) calculation can underestimate or overestimate mine NPV is presented, the conditions for each are outlined and the degree of underestimation defined.CITATION:Dube, T Y, 2012. How the use of market-based risk metrics can undervalue good mining projects and overvalue poor ones, in Proceedings Project Evaluation 2012 , pp 29-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By T Gartner

This paper describes the design, manufacture and site services associated with the supply of mine hoists for the new mine under construction by Falconbridge Limited in Ontario, Canada. Two new shafts are being sunk, and the hoisting equipment at each shaft can be summarised as follows: Ventilation shaft:4.66 m diameter double-drum second-hand hoist, originally in operation at San Manuel Mine, Arizona, to be used as the shaft sinking hoist. The second-hand hoist presented a challenge in that during its previous life, the hoist had been intensively operated during service at San Manuel Mine, and this paper describes the scope of refurbishment work undertaken, both electrically and mechanically, to ensure future reliable operation, together with the requirement to meet Canadian and Ontario regulations and codes of practice. 3.05 m diameter new single drum auxiliary hoist to be used as a second means of egress. Main shaft:4.57 m diameter new double-drum hoist to be used initially as the shaft sinking hoist, and subsequently to be converted to the equivalent of a single-drum multi-rope hoist for service duties during the production phase; 5.49 m diameter new double-drum hoist to be used for skip hoisting during the production phase; and 3.05 m diameter new single drum auxiliary hoist.The new hoists are all designed to comply with SABS requirements such that hoisting with reduced rope safety factors will be possible in the future. This paper describes the principles involved both mechanically and electrically. Particular attention is paid to the conversion of the main shaft service hoist from a double-drum sinking hoist to a multi-rope hoist.This paper describes the ac electrical powertrains (drives and motors) used that eliminate the need for harmonic filters and reactive power compensation equipment since they exhibit no negative effects on the utility electrical network system. This paper describes the logistical challenges of installing, commissioning and setting to work a series of five hoists in a short time frame.

Jan 1, 2005

By Roberts T, Firth B. A

A series of flotation experiments was carried out to study the interaction between the parameters of pulp density (mass per cent of solids in feed slurry) and frother addition (on the basis of solid mass feed rate). It was found that certain combinations of pulp density and frother additions caused large losses in yield. The interactive effect of these parameters can be primarily attributed to the total amount of frother added per unit of water. Consequently it is suggested that frother additions be made on the basis of water flow rate. As frother addition increased, in terms of the amount of frother per unit of water, yield increased rapidly but above an addition rate of about 10 g/tone it reached a plateau. Such results correlated well with qualitative visual observations of changes in bubble size and dispersion, with increasing levels of frother addition.

Jan 1, 1984

By D Felipe, G J. Harbort

In the past 40 years substantial changes have occurred in flotation machines. This has included increases in mechanical cell size to 630 m3 , significant changes to flotation column aeration design and widespread use of the Jameson cell and other pneumatic flotation cells. Over the corresponding period there has been increased used of machine characterisation measurements to benchmark and optimise flotation circuit performance. JKTech maintains a database of industrial flotation machine characterisation measurements. The database contains over 4000 entries and includes gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity, cell dimensions and impeller tip speeds. Data comes from numerous operating sites and commodity groups, including gold, copper, molybdenum, nickel, palladium, lead-zinc, platinum, silica, phosphate, coal and iron ore. Flotation duties registered include flash flotation, preflotation, roughing, scavenging and cleaner circuits. Measurements have been conducted on a wide range of flotation machines from different manufacturers. This includes forced air machines, such as Outotec and Dorr Oliver, and self-aerated machines, such as Denver and Wemco. The database also includes substantial flotation column entries, such as the Microcel, Eriez/CMT Slamjet and Jameson cell. This paper describes the flotation machine characterisation database and discusses the variation between different types of industrial flotation machines, in operating production circuits.

Aug 24, 2022

By L M. Zhang, T H. Xu, J Zhao

Blasting is one of the most commonly used strategies for excavation in civil and mining engineering. Yet blasting can also bring along such undesirable effects as ground vibrations and soil disturbance. Numerical analysis is a powerful tool for estimating the effects of blasting and improving blasting design. In this research, a constitutive model for sand is proposed for the numerical analysis of blast-induced ground motions and wave propagation in soil mass. In the model, three model surfaces, ie the critical surface, the dilatancy surface and the bounding surface, are defined following the bounding surface hypoplasticity framework. The strain rate is included explicitly into the model formulations so that the proposed model is valid under high strain rate loadings caused by blast-induced vibrations. The performance of the proposed model is validated by the simulation of drained triaxial compression tests conducted on a crushed coral sand under different strain rates.CITATION:Xu, T H, Zhang, L M and Zhao, J, 2014. A bounding surface model for sand subjected to blast-induced vibrations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By R G. Jeffrey

The Northparkes, Endeavour 26 orebody is a porphyry copperûgold deposit and comprises a moderately to well jointed rock mass characterised by gypsum veining, the intensity of which decreases with depth. The top 480 metres of the orebody is currently being mined by block caving, the undercut dimensions measuring 196 metres in length by 180 metres in width. Continuous caving was never achieved after the completion of the undercut thus cave inducement techniques were sought to maintain caving so as to safely sustain production. The use of hydraulic fracturing as a cave inducement tool was successfully trialled in December 1997 using existing exploration boreholes located midway up the current lift. Subsequent fracturing campaigns have enjoyed various degrees of success and have yielded in excess of seven million tonnes of ore at a significantly lower cost than conventional cave inducement techniques. Monitoring of both the hydraulic fracture system and the rock mass response has provided considerable insight into the geometry, growth and influence of hydraulic fracture networks above the Northparkes block cave, and has initiated additional research into the use of hydraulic fracturing in other mining methods.

Jan 1, 2000

By G Pizarro, O Miranda, D Rosales

In panel/block caving mines, large amounts of information are collected at the operations. This information includes grades and extracted tonnage, fragmentation, lithology, design of stopes and main infrastructure, geotechnical information, overbreak progress, seismicity, numerical modelling and many other mine variables. To improve the reliability of the production plan it is required to integrate the mine data into one platform. In this paper, the logic of a new technological platform is presented for analysis, modelling and design in panel/block caving mines. The platform includes an acquisition system for mine data and geotechnical information, a back-analysis module for calibrating statistical models and a module of visualisation of the results. The application and benefits of the platform is illustrated for mining induced seismic risk for panel/block caving mining operation. The platform can be used in the mine design and planning processes and is useful for reducing uncertainty in the mining business of panel/block caving operations.CITATION:Miranda, O, Rosales, D, Pizarro, G and Vallejos, J, 2016. Development of an integrated platform for the analysis, modelling and design in panel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 237–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016