Search Documents

By Bhattacharyya A. K>

The Pemali Open Pit Mine is situated in a small island called Bangka in Indonesia. It produces approximately 165,000 m3/year of tin ore with an average grade of 3.67 kg/m' of tin from a primary deposit. The deposit occurs at the rim of a granitoid intrusion within sedimentary beds. The rock formations, all extremely weathered, and the overlying alluvium, are exposed to a rainfall exceeding 3m/year. Serious slope stability problems are experienced at the mine, despite using overall pit slopes of 20¦-29¦, the latter resulting in a stripping ratio of 4:1. This paper outlines a computer based back analysis of a major slope failure involving some 250,000 m' of material which occurred on the west wall of the pit in February, 1984. The findings from the analysis, together with other information, are used to examine the stability of the east wall of the pit, where tension cracks developed later. The results indicate that the large influx of water was the most significant cause of such slope stability problems and a more intensified water management programme would be beneficial.

Jan 1, 1989

By Mitchell I, Gelfi P, Dunne R, Pyper R

Dump leaching at Teller in its present form began in the fourth quarter of 1988 as an adjunct to milling operations. Initial plans called for a dedicated dump leach facility capable of processing ore at an annual rate of 2.0 million tonnes. Construction of a dump leach pad, collection and process ponds, carbon adsorption system, elution plant as well as reagent addition and ancillary facilities was initiated in mid-1988. During the course of construction, additional reserves were proven. As a result, design throughput was increased to 4.0 Mtpa. Leach pad capacity and solution supply systems were upgraded to handle the larger throughput. However, the carbon adsorption/elution facilities were not upgraded due to space limitations. During 1990 it was decided to expand the dump leach operation to 6.0 Mtpa. Construction of a second leach pad was required which was initiated in early-1991. Plans were again upgraded prior to completion to a target annual throughput of 10.0 million tonnes was. A further two leach pads have been constructed. The first of these being completed during the latter part of 1992. Construction of the latest and largest pad commenced early in 1994.

Jan 1, 1994

By Hagan T. N

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974

By Gole MJ

The Goodyear nickel prospect is located 45 km southeast of Kalgoorlie (31.04¦S, 121.80¦E) near the eastern boundary of Hampton Area - East Location 45 (Figure 1). Nickel mineralisation was discovered on the Goodyear prospect in March 1996 when a reverse circulation drillhole (GYC5), initially drilled in December 1995, was deepened to meet a minimum footwall penetration requirement of 20 in that had been set for the drill program. Approximately 3 in of sulphides averaging 4.9 per cent nickel was intersected from 296 metres down-hole, this being within 2 in of the first end-of-hole. Hole GYC5 was part of an eight hole drilling program undertaken by Titan Resources in late-1995. This program was designed to test whether nickel mineralisation in the Dunlop prospect, discovered by the Western Mining Corporation - BHP Camylia Joint Venture immediately east of the East Location 45 boundary, continued across the tenement boundary. The area targeted by the initial drill program had been explored by Western Mining Corporation in the mid-1980s using extensive surface sampling and a drilling program that included 17 RAB and percussion drillholes. None of these holes intersected nickel Mineralisation.\

Jan 1, 1996

By Hodkinson I, Teale GS

Mount Leyshon is an open cut-heap leaching operation that commenced production in early 1987. Open pit reserves are 6.3 m.t. grading 1.8 g/t Au and 4.8 g/t Ag and expected annual production is 68,000 oz. of gold. Gold mineralisation is hosted in breccias, porphyry plugs and basement rocks interpreted as the roots of a multi-phase Permian phreatomagmatic breccia complex. Mineralisation has the form of veins, cavity fillings and disseminations and is localised by late stage trachytic dikes and sills and dike-like bodies of milled breccia in the northwest corner of the complex. The sequence of mineralisation includes: I quartz-chalcopyrite-molybdenite stockwork veins and pyrite-gold veins with potassic alteration II quartz-chlorite-carbonate-basemetal sulphide-gold veins and cavity fillings with sericitic alteration III quartz-basemetal sulphide-bismuth-sulphide -electrum veins, veinlets and dissemin- ations with sericitic alteration. Mineralisation is interpreted to have formed at 500-300¦C from a predominantly magmatic hydrothermal system related to the porphyry intrusive bodies. Mount Leyshon is a phreatomagmatic breccia with a very different origin to the Kidston magmatic hydrothermal breccia. However the mineralisation style and origin is quite similar.

Jan 1, 1987

The planned extraction of deeper copper ore at Isa Mine has necessitated a review of existing equipment and methods to contain costs and improve working conditions. Mining is in progress for a crushing-conveying system to serve the deeper southern areas of the 1100 Orebody. This system will permit direct tipping of ore to the crushers and conveying of the crushed ore by cable belt conveyor to existing shaft loading facilities, a distance of about 2 km. To develop part of the conveyor drive a new machine will be used, the Robbins MM120 Mobile Miner, a joint development project between The Robbins Company and Mount Isa Mines Limited. The Mobile Miner uses a rotating cutting wheel to excavate headings 3.7 m high and from 4.7 m to 7.5 m wide. To ventilate the deep crusher complexes and associated development at high virgin rock temperatures, a refrigeration plant will be built on surface to reticulate chilled water underground. Bulk cooling of air to the 3000/3500 Orebodies and the southern crushers will be combined with the reticulation of chilled service water to the lower workings of the mine.

Jan 1, 1984

Expansion of the B.H.P. Co. Ltd. mater ials handling facilities, at their Newcastle Steelworks, began in 1964 and continued until 1970. The present complex handles the annual iron ore requirement of some three million tons for the Sinter Plant and Blast Furnaces. Iron ore is discharged from ore carriers and conveyed at rates up to 3,000 t.p.h. to either of two 180,000 ton capacity storage yards, where it is blended using boom stackers. Material is reclaimed from these yards at rates up to 1,000 t.p.h. using a slewing boom bucket-wheel reclaimer and fed to a screening station. Oversize material is scalped out and crushed in a closed circuit cone crusher. Undersize material is sized on double-deck vibratory screens which separate at 1/4in (6mm). The two fractions are blended in two of four 70,000 ton capacity blending yards using slewing boom travelling stackers. Bridge-mounted bucket-wheel reclaimers reclaim the blended piles at 1,000 t.p.h. Fine ore is conveyed to the Sinter Plant and lump ore to a second screening station, for rescreening, before passing to the Blast Furnace.

Jan 1, 1972

By Rixon LK, Walton KP

Evidence will be presented to show that borescope inspection of mine roofs is one of the most useful techniques available for stability assessments. ACIRL currently has four borescopes, comprising two fibre-optic units of 2.7 m and 4.5 m length and two optical rod units (introscopes) 6 m and 8 m in length. (The 8 m unit is not yet fully operational because of modifications needed to meet safety regulations). Using the fibre-optic units, photographs of hole walls or ends can be taken to record features. Roof lithology and crack patterns can be observed in roof holes from 25 - 60 mm in diameter. Several crack parameters are useful: type, location in the roof with respect to height and lithological boundaries, presence of individuals or zones containing crack clusters and the estimated amount of dilation. These data are readily computer- plotted to form "borescope logs". Provided that the holes remain open, a hole or group of holes can be re-surveyed at intervals to monitor crack development across or along a roadway, for example with respect to an advancing blind-ended roadway face.

Jan 1, 1986

By Hein K. A A

The Mt Todd Gold Project is located 42 km northwest of the township of Katherine within the Northern Territory of Australia. It is situated in the southeastern portion of the Pine Creek Geosyncline. The Batman gold deposit, the largest of several deposits at Mt Todd, hosts an identified mineral resource of 92.9 million tonnes (Mt) grading 1.4 grams/tonne (g/t) as at 31 December 1993. Host rocks at Batman are assigned to the Early Proterozoic Burrell Creek Formation, comprising greywacke and siltstone interbedded with shale. Gold mineralisation is associated with a very broad zone of sheeted and stockwork quartz-sulphide veins that occupy a corridor of intense brittle fracture and faulting. A conceptual model of formation involves the dilation of joints and micro-faults within overlying sediments during sinistral movement along a basement shear zone. Synchronous granite intrusion generated convective circulation of crustal fluids through the sedimentary pile resulting in the formation of auriferous quartz veins within favourable structures. The Batman zone of mineralisation is not directly related to fold structures which typify several other major gold deposits within the Pine Creek Geosyncline.

Jan 1, 1994

The U.S. Bureau of Mines has developed a prototype cross well acoustic logging system and complementary tomogr`aphic image reconstruction software for the detection and delineation of abandoned underground mines and associated subsidence failure in relatively shallow environments. The logging system uses a piezoelectric, cylindrical bender as an acoustic source. A triaxial accelerometer assembly, designed to be rigidly locked in the borehole, is the receiver portion of the logging system. Both the source and receiver probes operate at high frequencies, thus providing short wavelengths capable of resolving small features in most rock types. A modified van with a dual-drum wireline winch, 4-channel data acquisition system, power amplifiers, and waveform generator supports field operation of the logging system. A field study was conducted at a test site in San Antonio, Texas, to demonstrate the cross well acoustic logging system. The underlying rock at the test site is similar to stratified sediments in coal measures. First- arrival travel times were interpreted by tomographic reconstruction of the velocity field in the two-dimensional cross section between the source and receiver boreholes. The resulting image correlates well with geological borehole logging data for the test site.

Jan 1, 1992

By West Coast Staff

Attention to the design of facilities for drainage, of both surface water and seepage, made it possible to attain, for a qam impounding residues from a concentrating mill, a more stable sand wall which can eventually be carried to a greater height.EXPERIENCE WITH No. 1 DAMResidue from the lead zinc concentrating mill, which treats the ore from the Rosebery and Hercules Mines, was pumped 3,600 ft. through a 5-in. diameter woodstave pipeline to the site of the dam. It was formerly delivered through a 4-in. steel pipeline.State laws prevent the residue being discharged to waste into the Stitt River. Furthermore, as a pyritic residue it is a potential source of sulphur.Between 1936 and 1956 more than 1,000,000 tons. of residue was paddocked. The run-of-mill product was roughly classified at the dam in a 6-ft. diameter cone classifier and the sand fraction was pumped by a 3-in. pump to the front wall of the dam across a shallow valley. The overflow gravitated to the rear of the dam (Fig. 1). Typical sizings were:

Jan 1, 1958

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974

By M Gao, V Lawson, W Valery

Changes in metal prices and mine output over recent years have required the Copper Concentrator of Mount Isa Mines to operate at annual tonnage rates varying from 4.0 million to 6.5 million tonnes. Several circuit combinations were operated during this period utilising up to two semi-autogenous grinding (SAG) mills and up to two ball mills. The aim was to maximise grinding efficiency and keep unit costs constant regardless of throughput rate. Measures to improve the SAG-ball mill unit operation were implemented with each circuit change. These included installation of a splitter to divert SAG Mill cyclone underflow back to the mill, increase SAG ball charge from four per cent v/v to eight per cent v/v, reduce in SAG top feed size and increase of ball mill grinding medium size. Modelling work and surveys led to a new design of the SAG liner profile from 60 rows of rail bar liners in a high-low arrangement to 40 rows of top hat liners in a high-high arrangement. An on-line SAG Mill feed sizing monitor was recently installed to improve grinding control.

Jan 1, 2000

By Smith J. W, Wilkins R. W T

This paper is a preliminary report of research on the Mount Morgan gold-copper deposit being done at the Division of Mineralogy, CSIRO. Fluid inclusion and sulphur isotope measurements were made on a suite of 11 samples collected by the staff of Geopeko Ltd. This suite contained representatives of the main ore and rock types of the deposit. Homogenization temperatures of fluid inclusions measured on quartz from 8 of the 11 samples, ranged from 172¦C to 276¦C and to this must be added a pressure correction (in this case, up to 50¦C) to obtain the formation temperature of the mineral. Sulphur isotope measurements were made on 34 sulphides from 8 of the 11 samples. The 6S values form a well defined group ranging from -0.5%oto +3.6%owith a mean of +2.4%c. Although the preliminary data do not indicate unequivocally the origin of the deposit they do impose restraints on the wide ranging suggestions that have been put forward. This work is complementary to the paper of Dr G. Gibbons who has described other mineralogical aspects of the Mount Morgan deposit, based on a more extensive suite of Samples.

Jan 1, 1974

The Nagambie heap leach gold mine commenced production of gold in September, 1989. The mine,120km north of Melbourne in Victoria, Australia, was developed by Perseverance Mining Cor- poration Ltd, a junior Australian mining company, with no other operating mines. Gold production to December 31, 1990 was 47,621 oz. The mine is now producing at the rate of about 45,000 oz per year. As of February 28, 1991, resources at the mine are 5.1 million tonnes measured, at 0.65g/t Au while reserves were 1.65 million tonnes at 0.86g/t Au of proven, heap leach ore, plus 0.37 million tonnes at 0.40g/t Au, of dump leach ore. Metallurgical recoveries expected are 80 per cent for the heap ore and 60 per cent for the dump ore. Perseverance Mining Corporation was listed on the Australian Stock Exchange on April 2, 1987, after a capital raising in March that year. At this time the company's issued capital was 4 million ordinary 25ó shares, 3 million of which were issued to the public to raise $0.75 million.

Jan 1, 1991

The last two years have seen a rapid change-over from mechanised cut and fill. stoping to the more economic and productive long hole open stoping method, such that today more than 80 per cent of total production is won from open stopes. At first drilling was by sub-level rings and/or parallel up and down holes from inter- mediate sill horizons using conventional exten- sion rod equipment. Sub-levels were developed no more than 40 metres apart to allow accurate drilling. Compact, crawler mounted in-the-hole hammer equipment was introduced as soon as it became available in Australia. Today, all open stope drilling is done with three Atlas Copco ROC306 rigs and two Ingersoll-Rand CMM jumbos. Fans of 115 mm diameter holes, varying from near vertical down holes to horizontal, are drilled with a burden of 3 m. Toe spacing varies from 3.5 m to 4 m. An Atlas Copco DG418 booster compressor is used to boost run-of-mine air from 700 kPa to 1400 kPa in the areas of longest drilling. This has improved overall drilling performance in these areas by 40 percent.

Jan 1, 1977

By W Uhlmann, U Grnnewald, B Nixdorf

Flooding with surface water is the preferred technique for the abatement of acidification from pyrite oxidation in the lakes of abandoned Lusatian lignite mines. However, water resources of the region are limited and in addition, interruption of water inflow during the summer and the termination of the flooding process after reaching the final water level can lead to a re-acidification of the lakes. The development of three mining lakes with a surface-water flooding history of six to 28 years was analysed û in two lakes on the basis of fortnightly to monthly hydrochemical monitoring data. During summer flooding interruption, the younger lakes showed a decrease in pH from neutral down to pH 4. The degree of the pH decrease depended on the intensity of the groundwater inflow from the overburden dumps and this affected the hypolimnion more than the epilimnion. The third lake was flooded 28 years ago and up to now, interruption of the surface water inflow resulted in re-acidification. These three examples were able to show the benefits and limits of the surface water flooding technique for the abatement of Lusatian mining lake acidification.

Jan 1, 2003

While South Africa is well endowed with mineral resources, it is generally accepted that its future will be determined more by the development of its human resources than its mineral wealth. The country has throughout its modern history suffered from an over-supply of unskilled labour and a shortage of skilled and professional manpower. There has furthermore always been an over-reliance on Whites as an internal source of professional manpower, supplemented by immigration wherever possible. Better utilisation of other population groups in professional positions has been hampered by the general lack of education and training among such groups. Although many problems still remain, there are emerging trends which are likely to positively affect the training of professional manpower in the future. The direct and indirect influences that are likely to affect professional training at the macro level include 1. government policy and objectives in respect of manpower education and training, 2. the emergence of technikons as fully- fledged tertiary education institutions, 3. demographic trends in South Africa as they pertain to education, 4. political and statutory developments in the country, 5. industry involvement in tertiary education, and 6. professional registration.

Jan 1, 1986

Average annual growth in consumption of primary energy in Australia over the past 10 years has been 5·5 per cent compared to a world average of 4·1 per cent.Over the next 10 years growth rate is expected to increase to 6 per cent per annum due largely to the rapid development in the mineral processing industry.By the end of the 19705 natural gas is expected to supply more than 9 per cent of Australia's primary energy market. Coal will supply 40 per cent and petroleum products 47 per cent. Nuclear energy will make its appearance but will make only a small contribution in the period.Australia has adequate reserves of natural gas and coal to supply its needs in the 1970s and beyond. However the newly developed reserves of crude oil, while supplying 60-70 per cent of requirements in the initialyears, will need regular and sizable additions if they are to keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated that new discoveries will need to approximate ten times the volume of recoverable reserves found in Australia to date.

Jan 1, 1971

By S MacKinnon, J Kok

Potential areas for improvement in flotation performance were identified during JKTech model development surveys in October 2003. Subsequent implementation of the JKTech recommendations in consultation with flotation cell manufacturer Outokumpu have resulted in gold flotation recovery increases of more than four per cent over a two-year period. One of these recommendations was the installation of High Shear Stators in the Cleaner and Recleaner flotation cells. The High Shear Stator installation project was justified based on simulations completed using JKSimFloat. Bubble size measurements completed before and after installation of High Shear Stators showed a reduction in mean bubble size of approximately 50 per cent in the Cleaner cells. Both Cleaner and Recleaner banks showed a significant narrowing of the bubble size distributions following the installation. Plant gold recovery increase resulting from the installation of High Shear Stators was 1.1 per cent, with a 1.9 per cent increase in flotation gold recovery and 5.4 per cent increase in flotation sulfur recovery. Based on the 1.1 per cent recovery increase and total project cost of less than $200 000, the High Shear Stator Project NPV was $8 200 000 with a 0.25 year payback period.

Jan 1, 2006