Search Documents

By G K. Robinson, M D. Sinnott

Three-dimensional granular flow models have been run to simulate three types of sample cutters: a cross-stream cutter, a vezin, and a cross-belt cutter. This type of modelling involves solving the equations of motion for large numbers of individual particles as they travel along a conveyor belt and interact with a sample cutter. It allows flows of bulk materials to be visualised and understood. Here we have used spherical particles. These results illustrate some advantages that modelling has compared to physical bias testing: By taking reference samples which are very close to the actual samples, the estimation of bias can be achieve quite precisely with very few runs. (Many Standards about bias testing recommend a minimum of 20 runs, but we have found that five runs generally provide adequate precision.) Potential bias can be divided into two components: the particles which are missed but should have been sampled and the particles which are extra but which should not have been sampled. This more detailed information can provide useful insight. Exactly the same material can be sampled using different sample cutters, thereby avoiding a source of variation that complicates physical testing. Much more detailed visualisation is possible, allowing better understanding of the bulk material flow in various circumstances.

Jan 1, 2005

By Z Lubosik, S Prusek, M Plonka, B Syrek

"The most commonly used method of thick coal seam extraction in Polish deep mines is multislice longwall (MSL). In MSL stability of goaf in the roof as a result of previous extraction in upper slice is a major geotechnical consideration that must be managed.This paper outlines the results of a wide range of investigations carried out in three longwalls that were in operation in a multislice system using caving with additional fly ash goaf stowing. The longwalls were operated by Katowicki Holding Weglowy SA (KHWSA) in the Upper Silesian Coal Basin of Poland.Examinations were completed on the properties of goaf at the roof of longwalls ie measurements of strength parameters of the goaf material by means of a borehole hydraulic penetrometer, determination of the goaf condition by means of a borehole endoscope and laboratory testing of the caved rock. The results of underground examinations of the loading on yielding arches in the gate roads associated with these longwalls and measurements of vertical and horizontal convergence are also presented.CITATION:Prusek, S, Lubosik, Z, Plonka, M and Syrek, B, 2014. Multislice longwalling for thick seam extraction – properties of goaf in the roof and gate roads behaviour, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 359–366 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By Okabe K

Development in the theory and practice of hearth drainage is reviewed. Difficulties in the hearth drainage were re- newed during late sixties and early seventies when the size of a blast furnace and the top pressure were increased to result in the increase in tapping rate. Hearth drainage was improved first by in- creased number of tapping and then decreased tapping rate as it was predicted by theoretical studies. State of the coke bed in the hearth, e.g., 'floating' or 'sitting-on' the hearth bottom, is discussed in relation with influential factors on it and its influence on the furnace operation. The 'sitting-on' coke bed is to be aimed at for the consistent furnace working and for the lower rate of erosion of the hearth refractory. As the continuous tapping became standard prac- tice in large blast furnaces, the interest in the basic research renewed. Prospect of the further research including mathematical modelling of the hearth drainage is discussed.

Jan 1, 1981

The deep seafloor in Papua New Guinea's proposed Exclusive Economic Zone appears to be a gold-rich province in the same sense as the territory above sea level. Two significant sites with polymetallic massive sulphide deposits forming today are known on neovolcanic ridges in the Manus Basin. Their high precious metal contents have led to renewed interest in the issue of exploiting seafloor mineral deposits. The prospects of finding other, possibly larger deposits in the region appear substantial. This paper reviews current data on seafloor deposits in Papua New Guinea (PNG) and raises some issues relating to future commercial exploration and mining of the sea floor. One of the known PNG deposits could become a prime candidate for the trials needed to develop technology, establish costs, and minimise environmental impact.

Jan 1, 1994

The Hall-Hoult process is likely to be the dominant method of aluminium production for the remainder of the century. The characteristics of the operation of a modern smelter are described and attention drawn to their disabilities which are due chiefly to the small production capacity of individual cells.The principal components of the Hall-H6roult cell - the electrolyte, the anode and the cathode - are discussed in order to identify the problems of scale-up. The factors influencing current efficiency and energy consumption are analysed and lead to the conclusion that the greatest potential for energy saving lies in reducing the anode to cathode distance (ACD).The most promising direction for major change is in the application of a new titanium diboride - carbon composite for coating of the surface of the cathode carbon. It improves the wetting of the carbon by aluminium and should permit the use of sloping cathodes and anodes. The deep metal pad would thereby be eliminated and, in the absence of magnetic perturbations, the ACD could be substantially decreased.The construction and testing of a full-size "Low Energy Cell" is scheduled for early 1986 and is expected to reduce energy consumption in aluminium production by about 15%.

Jan 1, 1985

The results of laboratory grindability tests on coal are of primary importance to the designers and operators of coal grinding mills, and coal handling plants in general. However, the potential industrial application of these test results have not been fully realised due to a lack of laboratory-test/field data correlations. This paper focuses on the grindability characteristics of Queensland coals, and provides a new look at an old problem in terms of (i) a more rigorous characterisation of the grindability properties of coal and its associated mineral impurities, and (ii) the correlation of laboratory grindability test results with the size characteristics of run-of-plant thermal coals, and their pulverising characteristics in full-scale mills. A new grindability test is also proposed based on the Yancey, Geer and Price laboratory abrasion-test mill.

Jan 1, 1991

By Kupper T

Firstly, electric analog models are discus- sed to show fluid streaming conditions. In these models the depth of blast at tuyere level, the height of the bath, the influ- ence of different angles of the furnace zones and the different possibilities of the root of the cohesive zone have been changed. Tests to define the influence at a large blast furnace are given. Secondly, the wear of carbon bricks in the hearth is examined under the influence of gas, slag and pig iron. Oxidation tests in a special scanning microscope with the pos- sibility of heating and gas treatment are shown. Wear mechanisms are discussed fora large blast furnace and proposals for im- provement are given. Finally, the possib- ilities and value of the temperature meas- urement in the hearth block are discussed.

Jan 1, 1981

By Vernon PN

The Eossing Uranium Mine is a high tonnage low grade open pit operation using acid leaching for uranium extraction and ion exchange and solvent extraction for solution purification. Advanced technology, much of it computer based, has led to major economies that have contained operating unit costs over the last four years in the face of double figure inflation. An improved ore reserve block model and mine planning system have achieved a considerable reduction in the stripping ratio. Drilling and blasting costs have decreased some 25%, mainly by the introduction of heavy ANFO explosive. A centralised computer control centre for the metallurgical plant has increased labour productivity resulting in improved process control. The all-staff workforce is united with management in the objectives of creating a safe, healthy, working and living environment and a prosperous company, capable of contributing to the wellbeing of the nation and the shareholders. This situation has been brought into being by an equal opportunity policy coupled with a management system emphasising open two-way communication through all levels in the organisation. The success of this policy is highly apparent in the morale and productivity of the workforce.

Jan 1, 1986

By Richmond A

Like many industries the coal mining industry has, since the beginning of this century, undergone many changes. Technological advances and the increasing demand for fossil fuels have introduced new mining methods and techniques which allow the extraction of thicker and deeper coal seams at higher rates of production. Most new methods of mining (or for that matter any other processes) introduce problems which the engineers of the industry are expected to face and resolve. Unfortunately, spontaneous combustion has plagued the coal mining industry since the first attempts to mine coal, and is no doubt partly responsible for the reputation that coal mining is a hazardous industry. The financial loss and toll of human lives due to the occurrence of spontaneous combustion of coal in coal mines is enormous, if not incalculable. Its occurrence today is less likely to claim lives, due to both improved methods of working and in the detection of spontaneous combustion sites.

Jan 1, 1983

By Heyer T, Wasmuth H-D

The concentrator plant of Fahrica Mine, that started production in 1977, was using nine Jones wet high intensity magnetic separators (WHIMS) of the standard type DP 317 with a 1.5 mm gap width for the production of pelletfeed concentrate. These WHIMS units were operating in parallel with a feed rate of 110 t per hour, with about 47 per cent Fe in the feed, and with a maximum of only 0.8 per cent magnetite. The field strength was about 1.2 Tesla. From 1986, the mine has adapted its production facilities to mine and concentrate larger amounts of lowgrade itabintes to maximise the use of the available iron ore reserves. An increase of up to three per cent magnetite in the magnetic separator feed, resulted in a reduction of capacity. This was due to partial clogging of the separation boxes at high field intensities, which were required for the recovery of the very fine hematite. Even by lowering the feed rate and the field intensity the problem could not be resolved. After extensive testwork in a pilot plant, with a Jones separator model DI' 90, the commercial WHIMS plant was modified into a two stage process using the existing nine Jones separators. The gap of the first stage with four machines was increased to a width of 3.5 mm, corresponding to a maximum field intensity of 0.7 Tesla. This first 'medium intensity scalping stage' is followed by a second 'real' high intensity WHIMS step with five machines operating at the original settings with 1.5 mm gap width and 1.0 Testa maximum field intensity. Feed rates of up to 320 tons per hour in the first and up to 240 tons per hour in the second stage could be achieved. The design concept of the concentrator at Fabrica mine is described using the old and new flowsheets. Details of the pilot plant testwork as well as actual performance data of the new plant section are presented.

Jan 1, 1993

By K Rozlapa, P Waters, H Middlemis

A major challenge for closure planning at mining operations below the water table is evaporation from final void pit lakes and concentration of salts, which can impact on downstream groundwater (and surface water) flows and quality. Where such impacts are deemed unacceptable, the closure approach that is often adopted is to infill the final voids with waste rock to above the pre-mining water table to prevent the development of a pit lake and subsequent evaporative losses. BHP Billiton Iron OreÆs Marillana Creek (Yandi) mining operations face these issues. The orebody is a channel iron deposit that forms the major aquifer in the region, which will be completely mined as a series of elongated open pits over tens of kilometres. The major constraint on mine closure planning was the stripping ratio of less than one, which means that there is insufficient waste rock to infill all areas to the pre-mining water table. Hydrogeological investigations and groundwater modelling indicated that standard mine closure approaches would result in pit void lakes becoming saline sinks unless the residual void geometry was optimised to minimise evaporation and maximise throughflow. The solution developed is a cost-effective long-term mine plan that meets all mine closure objectives, and involved:the selective infilling of all pits, largely using run-of-mine waste dumping with limited re-handling; the diversion of the major part of up-catchment creek flows around the mining operations to allow mining of the resource under Marillana Creek crossings, which in turn restricted overall aquifer recharge and reduced the elevation of the long-term water table; the diversion of some minor creek tributary flows into specific locations within the mine path to induce hydraulic gradients to maintain groundwater throughflow and water quality; and close integration of mine plan optimisation (mining and waste dumping schedules) with groundwater modelling scenarios to achieve acceptable environmental outcomes. This approach is designed to result in no reduction in downstream surface water flows or quality, maintenance of adequate downstream groundwater throughflow to support groundwater dependent ecosystems, and no reduction in the beneficial use status of the downstream groundwater resource.

Jan 1, 2006

By Holliday R, Floyd JM

A laboratory investigation was carried out to determine the distribution of gold between the products of lead-zinc concentrate smelting in the Imperial Smelting Furnace (ISF). Bullion, speiss and slag from the ISF at Cockle Creek were used as the starting materials to evaluate the effect of gold and copper content of products on the distribution of gold between phases under conditions simulating those in the ISF hearth. The ratio of gold in bullion to gold in speiss has a mean value of approximately 1.6 and is independent of the gold content of the bullion. The distribution coefficient of gold between bullion and speiss is dependent on the copper level in speiss and is lowered by increasing copper content in speiss. The ratio of gold in bullion to gold in slag is in the range 25 to 5700 and dependent on the gold content of the bullion. For low gold concentrations in bullion of the order of 1 g/t and a bullion to slag ratio of 1:3 the gold loss to slag is expected to be approx- imately 23%. In all tests the gold in slag remained low, in the range 0.05 to 0.5 ppm provided metal prills were not suspended in Slag.

Jan 1, 1986

Since gold was first discovered, mining development in the West Australian goldfields has been heavily dependent on the location of groundwater both for potable and mineral processing supplies . The location of adequate and economic sources of water has been a constant challenge to both explorers and developers throughout the history of the goldfields. The provision of a piped supply from Mundaring in 1903 greatly alleviated pressure on scarce resources, lowered mining costs and permitted the orderly development of infrastructure. However, increases in the demand for water resulting from new mineral discoveries over the past three decades has led to renewed pressures for more local supplies to be established. Wide-ranging groundwater exploration took place in the late 1960's and early 1970's, also, more recently, in support of intensified gold exploration. The collation and interpretation of the hydrogeological data from the whole goldfields region indicates that despite a low mean annual rainfall of between 180 and 350 mm, quite marked differences exist between the rates of groundwater recharge in different parts of the area, In general, these can be shown to diminish in a southerly direction contrary to a trend towards increases in annual rainfall. Recharge rates are related mainly to differences in rock weathering pattern, geological structure and physiography. The same differences have controlled the pattern of groundwater salinity and the magnitude of groundwater storages associated with the palaeodrainages. In the vicinity of the northern and western watersheds with the Gascoyne, the superficial sediments tend to be thin, may have calcrete in the section and contain moderate storages of brackish or even fresh water. This contrasts with the lower regions of the palaeodrainages where calcrete is absent and deeper erosion has permitted the accumulation of relatively large thicknesses of fine-grained sediments which are saturated with hypersaline water and constitute substantial storages. Account must be taken of these characteristics if water supply sources are to be optimised to meet the growing demands for groundwater in the region.

Jan 1, 1988

By Hoberg H, Schneider FU

Flotation tests were conducted with galena, quartz and with synthetic mixtures of the two, in different ranges of grain size, and with different process parameter variants. Physico-chemical analyses were also carried out on surface energy and on xanthate adsorption on galena with different grain sizes. Reference will also be made to hydrodynamics, interfacial chemistry and the influence exerted by grain size in flotation.

Jan 1, 1993

The winning and upgrading of mineral raw materials necessarily includes size reduction, which serves the liberation and production of marketable products from highly valuable and bulk materials. For crushing, the following factors can be duly accounted for depending on material type and the selection of the suitable machine: ò producing a particular size distribution, ò producing a particular grain shape, ò selective comminution, ò gentle comminution, and ò producing a size range required by a specific process and/or for a specific product.

Jan 1, 1993

By Musa MA

Tunnel excavation for sewer construction long remained a labour intensive, hazardous and costly operation. Even with the of mechanical and semi-mechanical shields for tunnel excavation, many problems remained until recently. In the past decade, however, the technology has changed dramatically which has made possible the use of advanced tunnelling methods for sewer construction.

Jan 1, 1993

Variety among deserts is nearly as great as among other climatic environments. Common to most deserts, and to areas downwind from them, is the dominance of aeolian transport of surface material, at least during some seasons of the year. The result is dilution of local surface materials with varying proportions of chemically uniform fine sand and silt, often imported by the wind from remote areas. Fortunately, desert pavement,.even though separated from bedrock by a meter or more of nearly pure loess, is simply a diluted reflection of nearby bedrock. Infiltration of loess through the surface debris and the rudimentary soil-forming processes in the desert usually preserve the integrity of the pavement. This pavement, or its "downstream" derivatives, provides a suitable sample for exploration geochemistry if proper care is taken to circumvent the aeolian dilution. The simplest and most commonly used method of circumventing the dilution is to use a coarse fraction of soils or stream sediments, discarding or retaining the finer fraction depending upon the magnitude of the dilution. Where the coarse surface debris is composed of rock chips representative of the bedrock sources, the method is successful. Under most circumstances the coarse fraction of the surface material will give a fair representation of gross lithology and will occasionally give an indication of mineral- ization. The major drawback to this approach is that selective weathering and erosion in the vicinity of mineral deposits often lead to the loss of ore minerals into the finer fraction, leaving a coarse residue enriched in feldspar and particularly in quartz; thus, the geochemical signature from a mineral deposit is effectively reduced or completely masked. The second most commonly used method to overcome aeolian dilution, and probably the most effective at present, is to use a heavy- mineral concentrate. This approach presupposes that the chemical signature sought resides in a heavy mineral. Fortunately, the arid weathering cycle is conducive to the formation of a wide variety of secondary ore

Jan 1, 1988

The population and the per capila consumption of mineral resources have both grown dramatically during the century past. It is argued that growth will continue through the century ahead but that the magnitudes of undiscovered resources are probably adequate to meet demands. The challenge that the mineral explorer of the future will face is finding deposits beneath several kilometres of barren rock.It is further argued that the principal challenge that society will face in the century ahead is the amelioration of environmental stress.

Jan 1, 1993

Backfil ling of excavated Sub Level Open Stopes has been underway since March 1989 and as at December 1992 some 1 100 000 cubic metres of Cemented Aggregate Fill have been placed. During these three years significant developments in fill quantities, types and cost have taken place.Operational improvements have reduced the quantity of Cement Aggregate Fill by 40 per cent. These results have been achieved by:ò rescheduling stopes,ò designing smaller primary stope, and ò use of uncemented rockfill.Unit cost for Cement Aggregate Fill have fallen in the order of 50 per cent through:improving fill hole reli ability,simplified barricade construction procedures, reducing the cement content,ò substituting dune sand for deslimed mill tailings, ò improved maintenance at the Backfill plant, and ò renegotiated site freight agreement.This paper will review the historical developments of backfill use at Olympic Dam.

Jan 1, 1993

By Semple DG, Leach TM

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as Zone C, is a measured 440,000t @ 17g/t Au and 46g/t Ag with an additional indicated resource of 120,000t @ 16g/t Au. A diatreme breccia localised at an intersection of structures, and a relationship of gold to base metal sulphides, are highly indicative of a porphyry association. Typical epi-thermal features such as crustiform banded quartz and quartz pseudomorphing. platy calcite are also present and locally contain lesser gold mineral-isation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100m strike. A fluid flow model suggests that mineralising fluids were sourced from the diatreme margins and migrated laterally along dilatant structures. Bonanza gold grades are derived through fluid quenching in the flexure between a hanging wall split which hosts much of the Tolukuma Hill resource and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting. Potential for more ore remains within the Gufinis and the 120 veins as well as in the outlying Prospects.

Jan 1, 1994