Search Documents

By Membrey W. B, Partridge A. C

Lower transportation costs, improved handling and better utilization efficiency are some of the reasons that make low moisture coal product desirable. There has been considerable interest in the development of effective coal dewatering techniques to achieve this result. One avenue of considerable merit for enhancing dewatering processes is by modification of the surface chemistry of the coalwater slurry system by chemical means, resulting in better performance of existing equipment. This paper reports the results of an investigation of the utility of surface active agents in the enhancement of fine coal dewatering. A large variety of proprietary dewatering agents have been studied in relation to their efficiency in enhancing the dewatering of a number of Australian coals. Properties of particular coals that make them amenable to improved dewatering by particular chemical agents have been identified. Surface studies, including surface tension and zeta potential measurements as a function of surfactant concentration, as well as dewatering assessments, were used. Particular attention was paid to filtration, but the results could be applied to other dewatering systems.

Jan 1, 1989

By Williams SR

Column Flotation cannot be used indiscriminately. Based on extensive pilot plant experience at Lakefield Research, a number of limiting parameters have been identified for the application of column cell flotation. Parameters of importance are the use of wash water, flotable mineral content, pulp viscosity, type of mineral selectivity being sodght and degree of mineral liberation. The paper discusses when wash water should be used and the positioning of a column within the circuit as this is important to maintain a sound water balance for the circuit and prevent excessive circulating loads. Other areas of debate are pulp chemistry, very low and high weight recovery, for which the conventional column is a poor selection of equipment, and treatment of complex ores, where the separation of valuable minerals is more difficult than non-sulphide, sulphide mineral separation. Based on these observations, the application of column flotation must be carefully considered or can be optimised.

Jan 1, 1993

By Cox I

Raiseboring is a technique that has become popular in modem mining engineering since the early 1960s. A study has been undertaken at the University of Queensland to determine important factors affecting the optimum diameter of raisebored shafts, excluding local parameters such as the maximwn excavation size that a particular rock type can safely accommodate.This model is used to examine each of these factors and the results indicate that the optimum diameter for raisebored shafts is generally between four and six metres.

Jan 1, 1991

By Cullen JF

Australia has a large resource of manganese at BHP's Groote Eylandt mine which has been progressively developed over the last two decades. While much of the product is marketed internationally to the iron and steel industry, substantial quantities are processed in Australia at the Company's ferro alloy works in Tasmania. In addition, small but increasing quantities of ore are being consumed by the non-metallurgical industry. Fluctuating fortunes in the steel industry produce similar trends in the marketing of manganese. The increasing cost of freight and power together with strict environmental control is further affecting the market balance. Mine operators are expanding into the alloy making field. Reduction in usage in less developed countries is occurring.

Jan 1, 1982

By Spencer GA, Saul SJ

The flight line spacing in low level aeromagnetic surveys is the principal factor governing both the cost and the amount of geological detail which can be extracted from the data. The rate at which geological resolution diminishes with wider line spacing is illustrated by progressive subsampling of a 200 m spaced data set from the Charters Towers region in Queensland.The usefulness of high frequency type filters in enhancing shallow structural features is seen to be limited to the 200 m data.It is concluded that each data set is suited to a particular scale and style of geological investigation with only the 200 m data having sufficient detail to identify the subtle structural patterns which are crucial to mineral exploration.

Jan 1, 1976

Major discrepancies between mine estimates and estimates from plant metallurgical balances are a common problem in many gold and base metals mines around the world. Many existing practices are based on practical protocols that often fall short

Jan 1, 1998

Precipitation of inorganic compounds or metals from aqueous solutions can either be physical (crystallisation) or chemical in nature. Chemical processes are varied; they may be due to hydrolytic action, due to ionic interaction, or due to reduction (ie transfer of electrons). Transfer of electrons in reduction processes may take place homogeneously or heterogeneously. In the first case it may be ionic or nonionic in nature. Heterogeneous processes may be electrochemical or electrolytic. Examples of interest to hydrometallurgy are given.

Jan 1, 1993

By Konishi Y, Morioka Y, Okabe K

A part of the results of dissection survey of Chiba No.1 blast furnace, Kawasaki Steel Corporat- ion, is presented. Distributions of coke size and of slag and metal holdup are shown in the region of the dropping zone. A similar relation to the irri- gated packed bed is obtained. The distribution of coke size, coke temperature and liquid holdup are measured in and around the raceway. The shape of raceway in the horizontal and vertical sections indicates that each raceway worked individually. Liquid flow in the dropping zone and around the raceway on the basis of holdup measurements is Discussed.

Jan 1, 1981

The middle-Devonian Dulladerry Volcanics is a complex of A-type, predominantly rhyolitic ignimbrites, lavas and breccias. They form a NNW trending belt some 90 km long and 10-20 km wide, east of Parkes, NSW. The volcanics are dominated by widespread ignimbrite units with minor basalts, sediments and rarer andesites. The volcanics were deposited in a sub-aerial, possibly continental rift setting and are similar in chemistry and age to the Eden - Comerong - Yalwal Volcanic Zone (EVZ) on the NSW south coast. The volcanics exhibit an unusual Atype chemistry (high Zr, Y, Nb, REE, Ga). This distinctive composition illustrates that the volcanics are not comagmatic with the adjacent Yeoval Granite Complex or Eugowra Granite, which show typical I-type fractionation trends. Epithermal gold veins occur in basalt and andesite in the Dulladerry Volcanics at Mt Aubrey (Hopf, 1992), near Baldry. Alteration also occurs in the Glen Isla and Red Hill areas, with epithermal sinter recognised at Glen Isla. Copper and minor gold mineralisation occurs at the contact of rhyolite and andesite at Reedy Creek, but is not of epithermal origin. The analogous EVZ also contains several epithermal gold fields and it is this style of mineralisation which provides the most prospective targets in the Dulladerry Volcanics. Although the Dulladerry Volcanics also contain high background levels of REE and metals such as Zn and Pb, the general lack of fractionation and water-undersaturated character of A-type magmas does not lend itself to the development of significant concentrations of these elements into a fluid phase and mineralisation. The prospectivity of A-type volcanics in general could not be regarded as high. However, an indicator of some fractionation in the Dulladerry Volcanics is provided by the fairly low abundance (average 230 ppm) and wide range (

Jan 1, 1995

A review of ground control procedures in Western Australian underground mines is presented. Geotechnical input into initial mine design and methods of ground control is rare. As a result, the frequency of unexpected rockfalls is comparatively high, with over three quarters of the mines adopting non-specialist ground control designs experiencing unexpected falls-of-ground. In contrast, mines that provide some level of specialist input into initial ground control design experience decreased rockfall frequencies.

Jan 1, 1992

By Bhattacherjee A, Makesh S

Mechanised sub-level stoping is one of the most widely accepted stoping practices followed in base metal mines in India. As a general practice, blast-scheduling of rings in these stopes is done either heuristically or randomly which leads to a high fluctuation in ore grade when drawn and delivered to the mill. In this paper, dynamic programming has been investigated as an optimisation technique for optimal blast-scheduling of rings. A microcomputer based dynamic programming algorithm has been developed in C language which runs under the UNIX environment. A case study based on Indian mine data is presented to demonstrate the application of the dynamic programming concept and use of the developed software. It is concluded that dynamic programming can be used as a production planning tool in Indian mines practicing sub-level stoping and following heuristic/random approaches for blast-scheduling of rings.

Jan 1, 1995

The patterns of flow of reaction gases through the flash furnace at the Kalgoorlie Nickel Smelter were simulated in a 1:20 scale model using a flow of water. Particular features of the flow down the reaction shaft, through the settling chamber and into the uptake leading to the waste-heat boiler were examined. Inferences were made concerning the effects of the patterns of flow on the efficiency of the smelting reaction, on the entrainment of dust by the gas stream and on the erosion of the refractory lining of the furnace. In addition, the effects of geometrical modifications to the arrangement of the concentrate burners and to the profile of the settling chamber were explored by making these changes to the model and observing the resulting variations in the patterns of flow.

Jan 1, 1991

By Johnson N. W, Ralston J, Lauder D. W, Smart St C R

The flotation behaviour of the Hilton ore of Mount Isa Mines has been examined in the presence of two collectors (sodium ethyl xanthate (Ex) and sodium diisobutyldithiophosphinate (3418A)) over a range of flotation Eh values and collector additions. Tests were also conducted in the absence of collector to determine the relative contributions of natural and self-induced floatability of the major minerals in the feed. In these tests the influence of metabisulphite on the self-induced floatability of the minerals was also determined. Attention focussed on optimising the selectivity of galena flotation. It is shown that the Hilton ore sample contained lower levels of naturally hydrophobic iron sulphide minerals than are generally contained in the Mount Isa lead-zinc ore. Furthermore, the self-induced floatability of galena was less than that exhibited by the galena in the Mount Isa lead-zinc ore. Sodium metabisulphite (MBS) reduced the self-induced flotation of galena but had no effect on the natural floatability of the iron sulphide minerals.

Jan 1, 1991

There are many variables in a flotation concentrator, some of which are outside the actual flotation stage, which affect metallurgical performance. The number of such variables which can now be measured on a continuous basis has increased significantly over the past 20 years. They can be broadly classified under the headings of physical, chemical, and elemental. In this paper reference is made to a number of such variables, and comment is made on the state of the art in their measurement. Although not confined to development in Australia, particular reference is made to the considerable Australian contribution in this area of Technology.

Jan 1, 1984

By Flann R. C

A small modification to current industrial practice should lead to better nickel powders for use in alloying, electroplating, and powder metallurgy. Nickel powder compacts sold for alloying are not always suitable for electroplating applications, since some presently used commercial powders will expand on sintering. Further, such nickel powders are unsuitable for use in the production of powder metal parts, because of expansion during heating of the near-net-shape preforms. Research in these laboratories has enabled the elimination of expansion, and led to techniques for the production of compacts suitable, in particular, for commercial use in both alloying and electroplating. The techniques include: powder pretreatment, cold pressing and sintering, hot pressing, and hot pressing and sintering. In this way compacts are readily prepared with densities of at least 93 per cent of solid nickel, and these, when used as anodes in Watts general purpose and bright baths, give both cathode current and plating efficiencies of 90-98 per cent.

Jan 1, 1979

This paper summarises the influence of slurry rheology on the grinding throughput of batch laboratory and continuous plant-scale mills operating in open and closed circuit configurations. The results of controlled changes in percent solids, particle size, slurry temperature, and viscosity control chemicals are demonstrated. An underlying rheological explanation of the above factors is offered which involves tying the specific rates of breakage that are occurring in the mill with the specific rheological character that the slurry is exhibiting at any given set of operating conditions. Some industrial scale operating guidelines are presented which have proven useful in increasing the net pro- duction capability of grinding circuits.

Jan 1, 1978

The need for the hydraulic transportation of coal in the New South Wales coal industry, both from the coal face to the surface and from the coal mine to the consumer or the port for export, is explained. Details of research projects currently in progress and involving the hydraulic transportation of New South Wales coals are given together with information on the hydraulic transportation of coal in the United States of America. The potential of hydraulic transportation as a viable alternative to the proposed expansion and upgrading of the New South Wales railway system to meet the projected New South Wales coal production to the year 2000 is described.

Jan 1, 1980

This opportunity to present a few thoughts on the question of professional education and training comes at a most appropriate time. In Britain, a great deal of energy is being expended in this, so-called, post-Finniston era, to create a new look for the status of engineers and engineering by the Engineering Council. Naturally, the tune and the tempo are being called by the big institutions which essentially serve the manufacturing industries. However, the Engineering Council in Great Britain also includes the mining and processing institutions such as the Institution of Mining and Metallurgy (IMM) and so there is a chance - if it is taken - for us to contribute to the debate and the determinations that emanate from it. The IMM, of course, caters for the professional status of those engaged in the mining and minerals industries and includes many who do not see themselves as engineers. Nevertheless, the debate is important to these other groups whose livelihood is inextricably bound up with those who are engineers and there are many facets of the engineering policies being shaped that will, I am sure, eventually be enshrined in the requirements for professional status across all the various disciplines in our industry.

Jan 1, 1986

By Eri G

Ok ledi Mining Limited underwent a major transition from radio based truck dispatching to computerized dispatching for its equip- ment fleet in October, 1996. Modular Mining's Computerized Dispatch System was selected based on reputation and superior customer support. Modular's dispatch system is a fleet management system that uses computer, data communication and global positioning sys- tem technology to produce automatic, optimized haul truck as- signments. Optimization is achieved by equally distributing trucks to shovels so that truck queuing and shovel idling times are mini- mized. Computer illiterate mine operations personnel had to overcome a rather steep learning curve to use the high technology equipment. fortunately the system was able to be configured to use bitmap

Jan 1, 1997

The effects of process variables such as solution chemistry, flocculent type and dosage, intensity and duration of mixing, and solids type and concentration, on the performance of flocculation/clarification/thickening processes are described. System response is evaluated in terms of the specific effects on floc settling, supernatant clarity and sediment compressibility. The implications of these results with respect to industrial practice are discussed and general guidelines for direct application to plant design and operation are suggested.

Jan 1, 1993