Search Documents

By Wright J

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

Misima Mines Pty Ltd (MMPL) operates a large open cut gold mine on Misima Island in the Louisiade Archipelago in Papua New Guinea. Misima Island lies approximately 600 km east-south-east of Port Moresby. The island is 40 km long by 10 km

Jan 1, 1994

By Hikosaka A, Chiba A

In a fundamental study of the physical chemistry of steelmaking slag, equilibra bet- ween hydrogen-water vapour gas mixtures and liquid slags contained in solid iron crucibles have been measured for four binary slags, FetO-CaO, FetO-Si02, FetO-TiO2 and FetO-Al203 at 14000C. From the data, the activity of iron oxide and the ratio of ferrous and ferric ions (A = Fe3+/Fe2+) were calculated for the slag composition. The best ionic model is found to be that based on regular solution of cations. The oxygen distribution between slag and metal is quantitatively expressed by this model over a wide range of slag composition.

Jan 1, 1980

By Hinchliffe WD, Griffin A

The desorption of gold from activated carbon is promoted by adding organic solvents to aqueous cyanide solutions. At 65-80¦ the elution of gold is fast and is not affected by water quality. The Micron Procedure involves pretreatment of the loaded carbon with NaCN/NaOH followed by elution with methanol vapour and condensate. Carbon is packed into a column above the distillation pot and acts as a fractionating column. Recovery of the methanol condensate leaves a methanol free concentrated gold solution and carbon containing

Jan 1, 1984

By Baohm C, Barker T

There have been significant changes in the Australian mineral sands industry in recent years due to changing supply and demand conditions, new product opportunities and opportunities for rationalisation of operations. Earnings within the industry have typically been volatile and this has been reflected in the share prices of listed mineral sands companies. Apart from the effects of variations in the state of the economy on the industry, share prices have also reflected the extent to which a company's earnings volatility is due to capital structure, the relative proportion of fixed costs to total costs and the nature of th'- sales mechanism. At the time of writing, the high prevailing share prices for industry participants and the current outlook for the industry would suggest that the time is opportune for raising equity capital. The immediate outlook for the industry and its various product segments appears favourable but beyond this the usual uncertainties remain. The new tax environment will cause most companies in the industry to have to rethink their dividend and capital structure policies. Most shareholders will now be concerned to maximize dividend receipts and minimise exposure to capital gains tax. Companies in the industry that have relied fairly strongly on earnings retention to help finance growth in the past will- need to look to increased equity raisings in the Future.

Jan 1, 1986

The selection of an appropriate mining method should take into account the geometry of the deposit and its physical properties. Other factors which assist in the determination are the requirements for flexibility in the mining process, minimisation of risk factors and maximising the financial return. Several established mining methods exist which can encompass the requirements to deliver the optimum mining method, this can be in both an underground or open cut environment. The objective is to outline these methods and where they can be applied in a mining project.

Jan 1, 1997

By Gleadow AJW, Foster DA, Kohn BP, Raza A

A large and increasing data base of apatite fission track results from sedimentary and granitic rocks exposed within the southeastern highlands and along the continental margin of Australia provides constraints for the tectonic development of the southeastern passive margin. The fission track results suggest that many regions of the southeastern margin of Australia experienced distinct episodes of relatively rapid cooling during the middle Cretaceous to early Tertiary that can be attributed to the effects of rifting. One cooling episode is middle Cretaceous in age and related to denudation of the southeastern highlands from Tasmania to northern New South Wales between -90-100 Ma. Rocks exposed along the present coast line record a later episode of rapid cooling, which is diachronous and decreases in age northward from -80 to 90 Ma in northern Tasmania to southern New South Wales, -60-80 Ma in central and northern New South Wales, and to -50-60 Ma in southern Queensland.

Jan 1, 1995

Subsurface information from the "Upper Coal Measures" of the Sydney Basin is interpreted by means of structure contour maps, isopach maps and geological cross- sections. Particular reference is made to recent coal drilling operations by the New South Wales Department of Mines. The study is restricted to the onshore portion of the Sydney Basin.

Jan 1, 1972

Martin Mining and Tunnelling Pty Ltd is a mining contractor with offices in Kalgoorlie, WA, Australia and Timmins, Ontario, Canada.Martin Mining and Tunnelling Pty Ltd offers services in mine contracting which include shaft raising, raise enlarging, excavation of rock passes and ventilating systems. It also offers the mining industry a unique mining method using the Alimak raise climber system.The Alimak raise climber system may be utilised in various types of orebodies, as the system is flexible to change. Sloping widths, drill hole patterns and changes in dip can all be accommodated with this method.This system allows for a highly productive, cost-efficient alternative to conventional longholing methods. This paper will focus on various aspects of the Alimak system which inherently make it a safe, viable method of ore extraction.

Jan 1, 1993

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

It is not often that mines have as much warning of the approach of bad ground conditions as was the case at the Western Mining Corporation, Kambalda Nickel Operations Lafranchi/Schmitz Decline. Most aspects of this operation are in fact quite unique and like the best solutions, the answer to the problem of weak and foliated ground conditions was relatively simple; requiring the use of readily available explosives although the idea of using it in this manner may not be the most obvious.The use of high shock energy POWERGEL 2131 cartridges proved to be the correct answer, in conjunction with small changes in drill pattern design. The resulting lack of overbreak bears testimony to the success of the concept and the commitment of the miners to achieving a safe working environment.

Jan 1, 1992

By Bhattacharyya A. K

The current methods for predicting pillar strengths are reviewed. A two-dimensional model, based on the Mohr-Coulomb failure criterion, is proposed for determining the compressive strength across the width of a long pillar. The model can be used to determine pillar strength and the depth of the crushed (ie yielding) zone from the pillar edges. The values of the parameters in the model, namely the cohesion and internal friction angle of the coal seam, friction angles at the contact of the coal seam with the roof and floor are determined by matching the strengths predicted by this model with the Bieniawski pillar strength formula for pillar width to height ratios up to 5. It is found that the derived values of these parameters are quite close to the results from laboratory tests. Based on the model, a preliminary analysis of pillar stability is made.

Jan 1, 1995

By Barlow S

The Kelian Gold mine project won two excellence awards from the Victorian Division of the Institution of Engineers, Australia. It was a challenging project, fast tracked in a remote and inhospitable tropical environment. The creation of a profitable and efficient mine was a significant engineering and project management achievement. The difficulties encountered and the way they were managed provide valuable lessons. These include the importance of sufficiently detailed engineering in all aspects of the job to enable the best estimates possible to be prepared during feasibility studies, the need to prepare the project scope and execution plan with disciplined and rigorous attention to detail by a highly experienced team and the value of identifying, assessing and mitigating risk and uncertainty during execution. The practical benefits of applying these lessons were demonstrated in the successful management of technical uncertainty on the recent diversion of the Kelian River to allow the expansion of the Kelian mine.

Jan 1, 1997

By Coombes J, Richards W. L

The objective of this paper is to illustrate, in a practical way, how both geologists and mining engineers can use conditional simulation to add value to their decisions. Inherent assumptions, requirements and essential components of condition

Jan 1, 1998

Stability on surface mining projects is primarily controlled by five factors. These include structural geology, the most important of the factors, the existence of weak layers, primarily clayey gouge or clay infill, groundwater, blasting and weathering. Case examples of stability on many surface mines including some coal mines are presented. The experience and lessons learned are applicable in some way to stability of surface coal Mines.

Jan 1, 1986

By Avraamides J, Ritchie I. M

Gold Tellurides are important sources of gold at Kalgoorlie, Western Australia, Cripple Creek, Colorado and Vatukoula, Fiji. Unlike free gold, the tellurides of gold are rather refractory and the usual treatment practice has been to oxidize the tellurides, either chemically or by roasting prior to cyanidation of the liberated free gold. There is a large measure of disagree- ment as to the actual cause of the refractory nature of gold tellurides. In order to investigate the leaching chemistry of gold telluride, a study was undertaken on the thermodynamics and kinetics of its dissolution using electrochemical methods. From this study suitable direct leaching condi- tions are suggested. In acidic chloride solutions gold telluride can be leached using iron(III) as the oxidant. At lower acid concentrations the reaction is controlled by the formation of a passivating film of H2TeO3. In alkaline solutions containing cyanide the rate of gold telluride dissolution increases with increasing pH and strength of oxidant. However, this can result in excessive consumption of cyanide in the presence of stronger oxidants.

Jan 1, 1991

This paper discusses why Argyle Diamonds adopted thickened tailings disposal in 1985 and how the system was developed over the next seven years. A wide ranging review of the thickened tailings disposal system and the tailings deposit it was producing was carried out during 1992 and 1993. The results of that review led to the abandonment of thickened tailings disposal at Argyle because of serious concerns about the stability of the resultant tailings deposit. The exposure to the risk of liquefaction and an assessment of the consequences if this happened to the thickened tailings deposit are shown. The criteria for selecting the new tailings disposal strategy are then described. The final section of the paper discusses the management strategies that have been put in place. These are designed to: ò reduce the risk posed by the thickened tailings deposit to an acceptable level; ò safely store tailings to the end of mine life; ò produce a land form that can be decommissioned to the satisfaction of Government regulatory bodies.

Jan 1, 1996

Ok Tedi Mining Limited commenced construction in mid-1981 of facilities and infrastructure to mine and process gold ore at Mt Fubilan in Papua ew Guinea. Production ofgold began more or less on schedule in mid-1984 although design capacity is yet to be achieved. Due to geotechnical problems, two important items of infrastructure, hydropower and permanent tailings disposal, are not yet in place. Current low metal prices make it likely that copper facilities will be postponed.The deposit compriscs a leached gold capping overlying copper sulphide porphyry mineralisation containing significant gold and molybdenum. Mining is by open pit methods. The soft leached capping gold ore is ripped and dozed, loaded by hydraulic shovel and trucked to a dump pocket. After passing a large semi-autogenous mill of nominal capacity of I, I00 tonnes per hour, the ore is treated by the carbon-inpulp process, with a gravity circuit to recover coarse gold. The final product is 12 kg dore bullion bars.At present, all tailings are detoxified with hydrogen peroxide; after cycloning, the coarse fraction is stored, and the slime fraction discharged into the river system; expected environmental impact is acceptable. Investigations for a suitable dam site for a permanent tailings system are still underway.Peak 'I. hour power demand for Stage I is 17 MW, presently supplied by a diesel alternator power station and a 2 MW mini hydropower plant.Initial access to the base camp at Tabubil was only by air. Eventually a road was pushed through 134 km from the river port at Kiunga (where port facilities have been constructed) and a further 23 km to Mt Fubilan.Roads are constructed of compacted gravel and crushed limestone generally underlain by geofabric. Eight major steel bridges were built.The town of Tabubil has been established, including housing, airport, shops, offices, schools and all facilities.Environmental studies have been extensive and a detailed monitoring program is maintained. Ok Tedi Mining Limited is making considerable efforts to train Papua New Guineans and to foster local business.

Jan 1, 1985

By Hinrichsen H. D, Rathburn D. R, Stieger W

The present situation in the field of iron ore pelletizing is briefly described with particular view of the Lurgi/Dravo travelling grate process. To meet todays pellet quality requirements with regard to physical and metal- lurgical properties it is often necessary to add basic fluxing materials. It has been de- monstrated that for certain ores, basic addi- tives provide a considerable improvement in fired pellet quality. The production of self- fluxing pellets is becoming increasingly attractive. One Lurgi/Dravo plant is now in operation and another is under construction which were designed for the production of self- fluxing pellets. Self-fluxing pellets may be considered as the primary or exclusive blast furnace burden and the installation of a sinter plant is not necessary if the pellet plant-can handle all in-plant fines. Reference is made to the first pellet plant utilizing iron ore concentrate, in-plant fines and basic flux. The use of solid fuel for pellet indura- tion is discussed because of the increasing prices and possible shortages of heavy oil and natural gas. Since there is a strong tendency to increasing plant capacities, the design fea- tures of travelling grate pelletizing plants for productions up to 6 million tonnes are Discussed.

Jan 1, 1974

In a state-of-the-an review of predictive methods for longwall support load calculation, special respect is paid to those techniques which enable actual roof conditions and local lithology of strata to be involved. Principal systems of roof examination include the borehole perforation test and seismic velocity measurements. Roof strata stability is related to caveability classifications and roof inclination due to subsidence. The critical analysis of both load resistance prediction methods and roof stability classifications shows that each has its own value of reliability level. The present research opportunities analysed underline the significance of developing fully reliable prediction techniques as needed by the coal industry.

Jan 1, 1991