Search Documents

Broken Hill is situated at an elevation of approximately 1000 ft. above sea-level, on the Barrier Ranges, in the State of New South Wales, Australia. It is approximately 700, 280 and 330 miles from the ports of Sydney, Pirie, and Adelaide, respectively.The summers are usually hot and dusty, with a recorded maximum shade temperature of 114° F. The rainfall averages approximately 9 in. per annum.

Jan 1, 1932

The paper describes the studies conducted to date on the short term adsorption/desorption of gases in coal from the point of view of developing techniques to predict imminent outbursting conditions in coal mines. A number of different parameters such as'dP express, K' and AV 0/60 etc. which have been effectively used overseas were studied on samples of coal from Westcliff and Leichhardt Colliery. Results indicate that these do not seem to be valid indices for predicting an outbursting condition. Based upon desorption isotherms, a new index defined as "L" has been developed which shows promising results. This index is in a position to differentiate the changes in the structures of coal and its proness to outbursts. The "LZ value determinations and its usefulness opens a new field where it would be possible to determine outbursting conditions from existing drill cores obtained during exploration studies or from long holes drilled in advance from underground workings. The index is more or less independent of the time elapsed between the extraction of a sample and the conduct of the test. The test for "L" can be conducted'on site or in the laboratory. The test is simple, easy to carry out and the "L" value for a sample can be calculated in less than 20 minutes. It could be adapted as a routine test for monitoring outburst conditions in mines.

Jan 1, 1980

Longwall mining has historically been considered an application for only deep reserves. This has changed in the recent past as longwall has become competitive with surface mining. Many resources marked for stripping now he in the domain of longwall. Today, the best longwall mines compete with strip mines operating in even the lowest stripping ratios. Longwall mining has become more widely applicable than it ever has been in the past and it is now generally considered the method of choice in situations where high levels of coal production are required. But the best way to use longwall mining has become less certain with the opportunities that highwall access provides. Wall-to-wall mining is the use of retreating longwall developed from and retreating toward a highwall. As a surface mine reaches its ultimate highwall, the opportunity for longwall punch mining or wall-to-wall mining is obvious. There are several clear operating advantages to operating a longwall in this way and where highwalls are available, the best economic decision will generally favor planning a direct approach. Yet wall-to-wall is not applicable in every situation even when highwalls are available. Moreover, the advantages of wall-to-wall mining do not always justify the cost of trenching or box cuts to access coal . However, many tactical advantages of operating from the highwall can be realized with the use of specially equipped blind drilled or raised bored shafts. This paper discusses novel techniques for a shaft assisted mining system which permits the addition of conveyor structure and mine systems from the surface to the face for advance and retreat mining with longwall, shortwall or room and pillar panels.

Jan 1, 1998

This paper discusses the use of tapered roller bearings in conveyor idlers. It shows that in medium and high capacity systems, tapered roller bearings can offer significant cost and performance advantages. In the next ten years, conventional conveyors will face increased competition from unconventional belt conveyors, pneumatic systems, pipeline "slurry" systems, unit trains and so on. The conveyor industry must meet these challenges by innova- tive use of technology. Conventional belt conveyors must continue to show the lowest cost per tonne-km or lose their position in the market. Tapered roller bearings can contribute to the achievement of this goal. The concurrent resources boom and liquid fuel crises may well see a decline in the use of heavy trucks for bulk material handling over moderate distances 10 to 50 km. There appears to be a trend in the conveyor industry to go to higher speeds with improved belting in conven- tional widths. The transmission of more material over a given period of time will place more demands on conveyor idler bearings. Australia has in general followed the European practice of using deep groove ball bearings in conveyor idlers.

Jan 1, 1978

By A E. Annels, M D. Raine, I M. Platten

Lode-gold systems are often characterised by a high to extreme nugget effect (>50 per cent), and the presence of coarse gold particles (>100 ¦m in size). They rank amongst the most difficult of ore deposits types, in terms of producing an accurate and precise resource estimate. Their effective sampling is generally difficult because of the relatively low concentrations involved and erratic nature of the gold particles. Grade continuity is usually less consistent than gross geological continuity, and is typified by the localisation of grades within discrete oreshoots. In most cases drilling, particularly diamond drilling is an effective measure of global geological continuity, whereas grade can only be reliably resolved from underground development. Depending upon drill density and geology, it is unlikely that anything above an Inferred Mineral Resource can be estimated from surface drilling alone. Underground development, in-fill drilling and, potentially, bulk sampling or trial mining will be required to delineate Indicated and Measured Mineral Resources and subsequent Ore Reserves. Grade estimation will have to account for highly skewed and often multi-modal populations, extreme values, a high nugget effect and low geostatistical ranges. A clear geological model that honours both geological and grade continuity must drive the resource estimation process.

Jan 1, 2003

By Brzezniak W

Conversion to trolley assist is a means of minimizing diesel fuel consumption, which in many mining situations offers a rapid payback of capital investment plus the inherent flexi- bility and maneuverability of truck shovel op- eration. Whendiesel electric truck shovel mining opera- tion with trolley assist is compared to alter- native mining methods such as conveyor systems, the trolley assist system can be easily justi- fied in terms of return on investment, payback and increased productivity. A review of present technology, performance requirements and past experience in the min- ing industry has led to the development of a trolley assist system for diesel electric haulage trucks which, is proven in the mining environment, offers significant reduction in fuel consumption and increased productivity.

Jan 1, 1981

By Hunter GW

This paper gives an account of the filling system at Mount Isa from surface fill production to stope discharge underground. A brief explanation of the surface facility and reticulation is given prior to the discussion on aspects of underground reticulation. These include fill hole types, pipe and breastplate installation, wear characteristics, etc. The different types of fill and their respective applications is mentioned as a prelude to a general overview of the mining considerations associated with fill placement and its role in the long term planning strategy at Isa Mine. Some practical aspects of stope preparation and filling procedures are outlined for the various stoping methods. Finally a brief outline of future fill developments is given.

Jan 1, 1982

The paper will review the marked upsurge in the installation of new continuous metal coating lines, both hot dip and electrodeposition. Although some of this new capacity has been replacement for obsolete facilities or directed at traditional markets, eg building products, consumer durables etc, by far the major portion is targeted at the automotive industry. The reasons for the rapid growth of coated automobile panels are discussed. A comparison of the installed capacity with projections for this market indicate that a severe over-supply situation has arisen. Many coatings are now available for the automotive industry, each with their own strengths and weaknesses, but none as yet wholly satisfactory. Coating development has mainly been cost driven. This favours hot dipped coatings, providing surface quality and pressing problems can be overcome. The high cost per unit thickness of electrodeposited coatings has also seen pure zinc coatings being replaced by thinner, more corrosion resistant alloy coatings such as zinc-nickel and zinc-iron. Recently resin overlays have been introduced to improve the performance of electrodeposited coatings. Developments in coatings for the more traditional markets will be described. The fastest growing market in the last decade has been prepainted product for the building industry. This has led to the installation of extra painting capacity and again it appears an excess capacity situation has occurred. Over the same period the traditional zinc coatings have continued to lose market share to the zinc/aluminium alloy coatings, Galvalume and Galfan. These have been joined recently by '1'aiyo Crack-Free which has been taken up by some metal coaters. Galvalume is now widely accepted as being the best available coating for unpainted applications. It is also suggested that 'spin-off' coatings from automotive developments might find a niche in the consumer durable market. The end users of coated products, particularly the automotive industry, have demanded improvements in quality, such as surface smoothness, formability, etc. At the same time the new coating lines have to process wider strip and run at faster speeds. To reconcile these somewhat incompatible needs has required numerous process improvements, many of which need in-line instrumentation and computer control. The more important of these changes are discussed briefly. Finally the paper will describe the recent developments which have occurred in continuous galvanising in Australia and put them into context with the rest of the world.

Jan 1, 1993

Roof bolting with resin bonded bolts has been developed extensively in French coal mines. There are three aspects of this development: 1. The reason for and the care used in the development of roof bolting from use as a reinforcement in a classical arched roadway to use as the only support in roadways in ad- vance of the working face (the roadway being reinforced behind the face); 2. The problems encountered and studied, such as choice of boltable roadways and determination of the technical data in designing a roof bolting pattern; 3. Only because roof bolting has been controlled by safety rules, and especially by accurate measurement of strata behaviour, has this system of support been expanded aapidly in France since 1967.

Jan 1, 1971

SINCE 1900, five underground fires of consequence have beenrecorded in the Broken Hill mines. These occurred at the Junction(1906), Proprietary (1906 and 1916), Block 14 (1906), and Centralmines (1923). All have been extinguished, but at an enormouscost; e.g., in the eleven months following on the 1923 Central mine fire the sum of £187,123 was expended in fire-fighting operations.To this series may be added others, as the South (1925) and British mine (1918) fires, which were extinguished before serious damage had resulted. All, however, have occurred within a period of 28 years, and in a district where spontaneous combustion, a prolific source of fire in the U.S.A., has been practically nonexistent. Therefore, definite fire risks exist in the underground workings of the Broken Hill mines, and, as a consequence, an active fire prevention policy is a necessity...

Jan 1, 1929

By Haslam C. O, Taylor S

Four historical periods of Australian lead-zinc-silver exploration and development are identified.In the first period, 1841-1900, Australia's deeply weathered surface yielded bonanza deposits. The outcrops of easily worked secondary ores, enriched in silver and lead, were discovered by prospectors with the incentive of production at times of high silver price. Districts discovered in this period still contributed, in 1982, 60 per cent of Australia's lead-zinc production, mainly from Broken Hill.The second period 1901-1944, was one of strong mine development but stagnant lead-zinc-silver exploration. Mount Isa was discovered and developed, but otherwise effort was devoted mainly to the mining of deposit extensions and to the metallurgical flotation of zinc. The deposit discovery rate was low but the discovery of Mount Isa was so significant that discoveries of this period contributed, in 1982, 30 per cent of Australia's lead-zinc production.The third period 1945-1972 was one of re-invigorated exploration.New geological and geophysical surveys, developing concepts of ore genesis, and worldwide comparisons of orebody settings improved target area selection. Evolving remote sensing methods, and rapid analytical techniques, assisted detection of lead-zinc deposits. Initiation of exploration led to discovery:1. in regions of previously unsuspected lead-zinc-silver potential (Sorby Hills, Mons Cupri, Golden Grove).2. of poorly exposed deposits in recognized mineral districts (Hilton, H.Y.C., Woodlawn, Elura, Que River).3. during active exploration for another commodity (Brown's, Woodcutters, Mary River, Beltana, Lady Loretla and Pegmont).The period saw a sustained growth in lead-zinc-silver production mainly from established operations. Mines discovered during the third period contributed, in 1982, 7 per cent of Australia's lead-zinc production.In the fourth period from 1973 to the present, exploration initiatives became fewer but resulted in continued discovery of poorly exposed deposits at Teutonic Bore, Thalanga, Benambra, Scuddles, Hellyer, and Jillawarra. Development initiatives strengthened in the period and production commenced at Woodlawn, Teutonic Bore, Que River and Elura; pre-feasibility work commenced at Scuddles, Hilton, Lady Loretta and Thalanga.

Jan 1, 1984

By Scales PJ

Fatigue is the primary cause of failure of structural and mechanical components subject to dynamic loading. Recognition of this basic fact and the development of appropriate techniques and details are important in the design and repair of off highway trucks (OHTs). The frames and appendages of OHTs and other mobile plant used in the Pilbara are subject to tough operating conditions. Any fatigue-prone details quickly show up and become a maintenance liability of considerable concern. Much of this equipment is approaching the limit of its fatigue life and maintenance managers face decisions on whether to repair or replace. Even new equipment often contains some poor details which suffer distress soon after commissioning. In those cases a repair is required which will reinstate the detail to its original intended design life. Repair details must be practical and cost effective. They must also be tailored to the capability and expertise available in the field or in local manufacturers' establishments. This is particularly important where original equipment was manufactured overseas and long delivery times are involved. Lessons are drawn from components which have failed, using the evidence constructively, to provide an upgraded part or an improved substitute. With the experience now available it is relatively easy to extrapolate to cover new problem areas. This paper describes specialised techniques of mechanical fastening and detailing for low fatigue susceptibility, built up over many years of experience with OHTs and other mining plant and equipment in the Pilbara.

Jan 1, 1982

By J Austin, R Bitencourt

Differences between the long-term model (LTM) and mine geology system (MGS) grade control block-outs on a blast block scale can impose difficulties to planning crusher feed grade and tonnes on a monthly to weekly blend basis. Detailed geological input to short-term planning has been integral to improve the performance and reduce risk in six-week to three-month production schedules and local variability in tonnage and grades is often not accurately represented in the LTM. The challenge of producing to combined target specifications from different mine sites in an integrated mine to ship business has been reduced with the creation of blast blockout-based short-term model. These short-term blast block models (STBBM or STM) are robust predictive tools created for upcoming benches of current mining areas by firstly collecting data from the pit in the form of bench and face mapping and projecting the structure and stratigraphy down to the next bench. A wire-frame of the projected contacts based on material destination from production blockouts is created and then checked against the LTM. Blast block data from the bench above including assay results and material logging is extracted and validated according to the projected wire-frames (geozones). Individual blast blocks and a full block model are created for each bench production defined by the STP (bench plans). Data output from the STM is in a compatible format for import into scheduling specific software packages. Additional information is incorporated into the STM to allow querying of drill penetration rates, predicted powder factors, material hardness and feed type to further aid in the production planning process and cost forecasting. To date, reconciliation of the STM has been pleasing and certainly an improvement on the LTM, especially in areas where variability is higher due to geological complexity. Short-term predictions derived from in-pit geological observations allow mine planners to more confidently decide on mining block sizes and schedule tonnages and grades, reducing the risk component attached to developing production schedules based directly upon long-term orebody models and mine plans.

Jan 1, 2005

In taking the chair at this meeting of the Australasian Institute of Mining Engineers, I feel it my duty to thank you for the honour you have conferred upon me by electing me President for the current year, especially as Bwken Hill is the birth place of the Institute and myself one of its foundation members. I will now endeavour to entertain you for a short time with a few reminiscences of Broken Hill from its inception. Beyond the fact that the mines on the Broken Hill lode have paid to their shareholders in dividends and bonuses no less a sum than £896,500, created and maintained a city of 25,000 inhabitants. supplied a large proportion of the revenue on the railways of a sister state, and made their influence felt throughout the 'commercial centres of the world, very little, I regret to say, is known by the general public as to the form, extent, or vastness of the ore bodies, or the mode of occurrence of the various classes of ore which have been found to exist in them. It has occurred to me that a short paper by the senior mining manager on the line of lode might prove interesting. There has been great difficulty in getting some of the figures relating to the field, the total output of metals from the Broken Hill mines not being obtainable from the Mining Department in Sydney j but an inscription on the foundation stone of the Technical College recently opened in this City, sets forth that the Broken Hill Mines started in 1880...

Jan 1, 1903

The sulphide ores of the Kalgoorlie goldfield have long been looked upon as' refractory, involving special metallurgical treatment. For many years two kinds of treatment have been practised-(l) wet treatment, including fine grinding, amalgamation or concentration of the free gold, concentration of the sulphide minerals with subsequent roasting and cyanidation, and cyanidation or bromo-cyanidation of the residue from the concentrating operation; (2) dry-crushing of the ore and roasting the whole of thecrushed ore, amalgamation of the gold in the calcine during fine grading, followed by cyanidation. The wet treatment was advanced a stage further when, in 1929, the Lake View and Star Ltd. adopted large scale flotation. As a consequence, however, further metallurgical problems were introduced. This paper covers the investigation, ,of one of the most prominent of these problems.Flotation preceded by strakes was satisfactory to a point.The flotation concentrate consisted largely of auriferous pyrite and tellurides, and the gangue minerals in the concentrate were practically barren.Several sources of loss of gold values were, however, found to be associated with this circuit, viz.-(a) There was the loss of gold in the flotation tailing.(b) Loss by dusting during roasting of the flotation concentrate.(c) Loss of gold in the cyanided residue.

Jan 1, 1937

The major greenhouse gas emissions from coal combustion are leading certain people to argue for uranium mining and nuclear power to meet these challenges. Although there is considerable rhetoric around promoting nuclear power as 'green' due to its relatively lower greenhouse intensity, a careful study of the data is required to properly underst and the sustainability of uranium mining and nuclear power and whether it can or should have a role in future energy supply scenarios. This paper presents detailed research and analysis on uranium mining, focusing on known economic resources, production, solid waste and water management, pollution issues as well as energy and greenhouse aspects. A particular focus will be on Australia and its operating and prospective uranium mines. Overall, the paper raises fundamental issues concerning the long-term sustainability of uranium mining and nuclear power and documents the greenhouse intensity of uranium production and the nuclear fuel chain.

Jun 1, 2010

The mine manager is one of the oldest jobs in the world. Over many centuries the fundamentals of how this job was approached did not change much. However since the later part of the 1980s there has been a dramatic shift in the expectations and role of the mine manager as the pressures of globalisation and consolidation have increased the size of companies and the production levels of mining operations. The changes have been dramatic, with demanding requirements on mine managers to continually improve the skill levels of people, to apply and develop rapidly changing technologies and to consider far broader business issues that need to be managed in a truly globally connected world. This paper will attempt to outline some of the issues, the complexity surrounding them and some of the approaches that have been made to manage them. There is not a single correct answer or approach, but there are many key success factors that have led to some amazing levels of performance being achieved as we go deeper, broader and literally move mountains to meet the customerÆs needs for today and tomorrow. This contrasts with many mining operations in developing countries that still have a traditional approach to how they mine. Society is the river of life that continually flows and changes the environment that surrounds it. The pressures from the customers and world growth, shape and force alterations to be made in an industry that has to live with the far greater primal and uncompromising forces of the earth we mine. This has led to some paradigm shifts in how we accept what we manage. TodayÆs mine manager must manage a far broader range of issues, than just how do we get tonnage out of the mine and product out of the ore. These include but are not limited to technical, commercial, product quality and end use understanding, employee and community issues, environmental and the ever increasing complexities of sustainable development. Organisations will have to look at how they structure their management of the business to manage functions to meet the complexity of different stakeholders needs û the business, the employees, the customer and the broader community within an environment that is becoming more attuned to the harm impacts to the world in which we operate. The attraction and retention of skilled people that contribute to the value and worth of the corporation, will become critical to sustain a companyÆs growth. One of the fundamental elements of successfully doing this will always be the skills of the mine manager and his/her extended team with the continued development and support that they will need to meet these demands.

Jan 1, 2006

The safety culture in mining has progressed towards a zero tolerance of injury. This change has required that some historically inherent risks of mining are engineered out or reduced. One of the significant causes of fatality in Western Australia and Worldwide mining is through rock fall, subsidence and inrush. Efforts put into understanding the material properties of the ground we mine and the backfill we place are reflected in improved safety statistics. It is no longer acceptable to not manage these risks and mining, to be sustainable, has to be safe.   Mining historically produced waste products with little consideration of recycling or impact on the surrounding land. The rehabilitation of mining waste products such as mill tailings, heap leach and waste rock is one step towards managing the environmental impact of these waste products. A better step is towards recycling and redepositing these products to produce a more environmentally sustainable mine site.   Gold fields St Ives lease is an active network of new and historic undergrounds and open pits within the Lake Lefroy and Kambalda district. The process of creating voids underground followed by open pits mining through the old voids allows the use of backfilling to control inherent hazards and dilution. Backfill provides opportunity for the disposal and recycling of mining waste materials at the same time as meeting requirements of mine support. Materials available on the St Ives site include spent heap leach, reclaimed tailings and waste mullock. Through recycling and re-depositing these materials to St Ives and neighbouring mines, the reliance on imported material to meet their needs and impact on surrounding land is reduced.   At St Ives, paste fill and barricade design have been reworked to allow backfilling into stopes with water inflows up to six litres per second. This has required a rethink of the drainage and monitoring of water management systems previously used for hydraulic fill and apply them to paste.   The St Ives open pits have developed methods to mine through underground workings and individual stope voids up to 62,000m3. Here backfill is used to reduce the consequence of catastrophic, unexpected failure of the crown and minimise ore lost down voids and dilution through increased blast movement. This paper outlines the less common methods being adopted to use the recycled materials and ways it has been managed to suit the needs of the company.

Jun 1, 2010

By G Kennewell

At 11 am Monday 8 September 1997, the successful detonation of the 5/9 Mass Blast at Pasminco - Elura was signified by the subsiding of æMt KevinÆ (a 15 m high earth fill mound). The blast was in response to earlier mine subsidence, which holed through to the surface affecting future stability of underground workings. The blast was a first for Elura which fires small tonnages regularly to avoid rapid oxidation of the ore. This paper discusses the strategy and the considerable planning that went into EluraÆs first blast of this magnitude in order to succeed first time round.

Jan 1, 1999

By Akerkar D. D, Dey M. L, Mathur S. B, Chowdhury S. K R

The extraction of gold and silver from chalcopyrite concentrates has been investigated. In view of the recent interest in non-cyanide leachants for gold and silver, one such alternative reagent, namely thiourea, has been employed in the present work. Precious metal leaching was attempted from received copper concentrates as well as pre-oxidised concentrates. Pre-oxidation of the concentrates was carried out by three different methods, namely roasting, pressure oxidation and biological oxidation. After pre-oxidation and leaching of the base metals, the leach residues were subjected to further leaching for precious metal extraction. The results obtained on the extraction of gold and silver from received concentrates as well as pre-oxidised concentrates are presented and the effectiveness of the three pre-oxidation routes employed is compared.

Jan 1, 1992