Search Documents

By M Behrens, A McPhee, B D. Hegan

This paper describes the design and construction of twin 400 m long road tunnels as part of the Northern Motorway Extension Project in Auckland, New Zealand. Construction of the tunnel civil works is now completed and installation of mechanical and electrical systems is well underway. The tunnels are expected to be open for traffic at the end of 2008. The paper will address the design aspects of the project including: tunnel alignment and cross-section, geotechnical conditions and rock support, waterproofing and concrete lining and fire and life safety. The paper will cover the bored tunnel section, the cut-and-cover tunnel section, cross passages and portal structures. The design brief included a requirement for the tunnels to be a gateway to Auckland and this required particular attention to be given to the visual appearance of the finished tunnel structure. The final arrangement of the portal structures and a requirement for recesses in the concrete lining for emergency cabinets, deluge pipework and cable runs, reflects these requirements. The tunnels were excavated by a roadheader and road planer using a heading and bench. Initial support was provided by a combination of lattice girders, cement grouted rock bolts and steel fibre reinforced shotcrete. The permanent lining consisted of installation of a drainage geotextile and waterproof membrane, followed by cast in situ unreinforced concrete. Each portal consists of a cut-and-cover section. This paper describes the tunnel construction methods, including the particular requirements for safety, the environment and community relations. The tunnel is fitted with a compartmentalised deluge system for fire fighting purposes. The tunnel control centre is incorporated into the control centre for Auckland Harbour Bridge, some 30 km from the tunnel location.

Jan 1, 2008

By Webster SS

This paper uses computer modelling tech- niques to compare and contrast anomaly patterns obtained with fluxgate (vertical field) and proton precession (total field) magnetometers at typical latitudes in northern and southern Australia. The use of these modelling tech- niques is suggested as an aid to magnetic interpretation and field examples are included from Tasmania and the Northern Territory.

Jan 1, 1975

Geostatistical conditional simulation is a method to assess variability and risk in mineral deposits and the tool has wide potential applications in the iron ore industry. Correct reproduction of multivariate relationships is important in iron ore simulation, especially between Fe and impurities such as Al2O3, SiO2 and P. The turning bands simulation method, using a full model of coregionalisation for multiple attributes, is the main multivariate conditional simulation algorithm used in the Western Australian iron ore industry. This paper discusses the results of a more recent approach using minimum/maximum autocorrelation factors (MAF) to transform and decorrelate the multivariate data prior to independent sequential Gaussian simulation (SGS). MAF-SGS results are compared to those of the turning bands approach in the Yandicoogina channel iron ore deposit (CID), and both methods performed well in simulating Fe, SiO2, Al2O3 and P distributions. Extensive checking of simulations showed that both approaches could reproduce multivariate statistics and spatial continuity of the original conditioning data. Both approaches reproduced the histograms and variography of input sample composites. While the MAF-SGS approach requires additional transformations when compared with the single normal scores transformation required for the turning bands method, MAF requires only that the direct semivariograms be modelled. In contrast, using turning bands with multiple attributes requires modelling a full linear model of coregionalisation, which can be difficult to model because of the need to ensure the model is positive semi-definite. Turning bands may be preferred if there are a modest number of correlated variables allowing construction of a linear model of coregionalisation that adequately models the multivariate behaviour. MAF-SGS is preferable for larger numbers of correlated variables. Both MAF-SGS and turning bands methods performed well in conditional simulation of correlated variables at Yandicoogina.

Jan 1, 2007

Tokyo Metropolitan Government designs the stormwater storage plans in underground, as a measure of flood control in completed urban district and improvement of combined sewarage system. This time, introducing those plans, we report about IKEJIRI and SIN-KOMAZAWA STORAGE TRUNK LINEs design and construction. They are located in Meguro river basin of the Morigasaki drainage area. Both storage trunk lines have capacity to store 15O,000m3 of stormwater. They are in use for countermeasure of flood till Meguro river's strengthening (intensity 50 mm/h) is ended. And after the strengthening, they will be in use for improvement of river water quality, through the storage of combined sewage and first runoff, which, otherwise overflows weirs and flows to river in a rainy day. These storage trunk line's full length is about 5700m. Boring diameter 66140 mm (f = 2672m) and 47800 mm (I = 2866m) of these tunnels are constructed by Mechanical Shield tunnelling method. And boring diameter 3600 mm x 4000 mm (R = 180m) is constructed by NATM tunnelling method. We began works in 1983, and have a mind to complete in 1987.

Jan 1, 1987

By W A. Ducker, R-H Yoon, M Mao

Froth flotation relies on an attractive force between a particle and a bubble to selectively extract particles from a mixture. The range and magnitude of this attractive force is an area of ongoing investigation. We describe measurements of the effect of dissolved gases on the long-range attractive surface forces between a silica plate and a glass sphere in aqueous octadecyltrimethylammonium chloride (C18TACl) solutions. The measurements follow on the work of Sakamoto et al (2002) who have concluded that long-range interactions occur in air-equilibrated surfactant solutions but not in degassed solutions. In the present work, we have measured attractive forces that have a much larger in magnitude than the expected van der Waals force in solutions that were degassed by the same procedure used by Sakamoto et al (2002). We find that the forces are most attractive at 5 + 10-6 M C18TACl, which is close to the charge compensation point (ccp) of the glass sphere. At this concentration, the attractive force decays exponentially with distance and the decay length is 34 in air-saturated solution, and 38 nm in degassed solutions. In both air-equilibrated and degassed solution, the force is quite sensitive to the concentration of surfactant. The force is also sensitive to the pH. We note that our degassing procedure increases the pH of the solution from about 5.7 to 6.6 (presumably by removal of dissolved CO2). We find that the forces measured in degassed solution can be reproduced by using a solution that was equilibrated in air, then the pH was increased by addition of NaOH. Therefore, we conclude that the main effect of degassing in our experiments is to raise the pH. We show that the range and magnitude of the attractive force decreases in the presence of salt (NaCl). This suggests an electrostatic mechanism for the attraction. Possible mechanisms for the attractive force are examined, including the mechanisms that rely on a patchy coverage of surfactant on the silica surface.

Jan 1, 2005

This paper examines the latest advances in mine drive and motor systems. In the last decade, the drive technology employed for large mine winders has migrated from the traditional dc technology to ac motors with cyclo convertor drives. Recent advances in pulse width modulation (PWM) drives have resulted in these being applied to large winder drives. While having many advantages for the winder system, the PWM drive must be carefully designed to ensure long-term reliable operation. When combined with induction motor technology, the PWM drive presents the ideal solution for winder drives. This paper examines the factors in choosing a suitable PWM drive for a winder installation. Factors under consideration include: winder duty cycle, drive rating restrictions, choice of power semiconductor device, cooling, and low speed operation.The cage induction motor is the motor of choice for large winder drives and has a number of advantages over the synchronous motor. The induction motor is ideally suited to integrated winder applications where the motor is built inside the friction drum, as installed at WMCÆs Olympic Dam site. The challenges of integrating the induction motor into the friction drum will be detailed, including: assembly, ventilation, air gap adjustment, and position sensors.

Jan 1, 2005

By G Harbort, T Georgiev, M Phillips

Phu Bia Mining Ltd, a subsidiary of Pan Australian Resources Ltd owns and operates the Phu Kham copper concentrator located in the Xaysomboun District, Lao PeopleÆs Democratic Republic. Construction and commissioning of the 12 Mt/a copper concentrator and associated facilities was undertaken by Ausenco Ltd and handed over to Phu Bia Mining Ltd in April, 2008. The first copper concentrate was produced in April 2008 and the ship carrying the first shipment of copper concentrate set sail 27 July 2008. Nameplate mill throughput was reached in August, 2008 when 1 020 000 dmt of ore was treated in the milling and flotation circuit. The Cu-Au mineralisation is contained in skarn and stockwork mineralisation and is interpreted as a distal expression of a conventional porphyry copper-gold system. Copper mineralisation is principally in the form of chalcopyrite with lesser bornite. Gold occurs as small grains, typically associated with copper minerals. In the upper portions of the orebody, oxidation and water table movements have resulted in near surface leaching of the copper and below the leached zone, supergene enrichment resulted in chalcocite mineralisation. The circuit operates with a semi-autogenous grinding (SAG) û ball mill circuit, feeding a bank of OK200 rougher cells. Rougher concentrate is reground in an IsaMill prior to entering a cleaner circuit consisting of three stages of cleaning and one stage of cleaner scavenging. The concentrate typically assaying 24 per cent Cu and 6 - 7 g/t Au is hauled for over 1000 km across the border to the Port of Sriracha in Thailand, and stocked in sheds at the wharf from which it is shipped to various Asian smelters. This paper discusses the successful commissioning and ramp up to design tonnage and metallurgical performance. In addition, a program to optimise both the comminution and flotation circuit is detailed with reference to grinding efficiency, flotation residence time and size by size mineral recovery.

Jan 1, 2009

By B, R E. Browner, H R. Watling

A number of hydrometallurgical treatment methods are being developed to extract copper from chalcopyrite flotation concentrate including microbial leaching and ferric sulfate leaching. However, chalcopyrite is difficult to process efficiently by hydrometallurgical methods as it exhibits slow reaction kinetics. Comparative leaching tests do not always satisfactorily explain or predict observed copper recovery, acid consumption, or differential leaching of minerals. This is especially true when reactive gangue constituents are present. The aim of this study was to determine how the leaching regime (microbial versus ferric sulfate) affects both the extraction of copper and residue mineralogy. Chalcopyrite flotation concentrate was leached at 30¦C and 65¦C using a pure culture of Acidithiobacillus ferrooxidans and a mixed consortium of thermophiles, respectively. In addition, the concentrate was leached at the same temperatures using 0.1 M ferric sulfate. Microbial leaching of chalcopyrite extracted more copper than ferric sulfate oxidation of chalcopyrite at 30¦C, demonstrating that the microbes promoted the solubilisation of copper at this temperature. This result was confirmed by leach solution analyses and residue analysis using quantitative X-ray diffraction (QXRD). More chalcopyrite was oxidized with ferric sulfate at 65¦C than at 30¦C (as expected). QXRD confirmed that pyrite reacted during ferric sulfate leaching at 65¦C but was relatively unreactive during lower temperature leaching. The high ferric ion concentration in the ferric sulfate leach at 65¦C led to significant precipitation of jarosite. This phase was only detected in small amounts at 30¦C in both the microbial and ferric leached residues. Sulfur also precipitated in the ferric leaching at 65¦C whereas no sulfur was detected in the microbial leached residue. Quartz was a relatively unreactive mineral phase regardless of the leaching medium and temperature. QXRD analysis indicated the residue mineralogy differed with different leaching regime.

Jan 1, 2004

In mineral asset valuation the use of any valuation method requires the input of competent and independent technical professionals. A resource valuation must be as transparent as possible to allow others to assess the validity of their underlying assumptions. Materiality is a dominant factor in all valuations and a valuer should set out the basis for the subjective decisions made in this regard. Any valuation methodology must comply with the requirements of the law, practice notes and guidelines issued by the various relevant authorities and professional bodies. The valuation methodology chosen to value a mineral asset depends upon the amount of data available on that asset and the reliance that can be placed upon those data. Mineral assets generally fall into one of three broad categories, depending upon their state of development, ie whether they are at the exploration, development or operating stage. Naturally there are transition phases. Hence, there are ""Grass Roots"" Exploration Areas and Advanced Exploration Prospects; Pre-Development Projects and Developing Mines; and Operating Mines. The features of each of these mineral asset status categories are described, mainly in terms of the confidence in the contained identified Resources/ Reserves. The various subjective methodologies available for the valuation of ""Grass Roots"" Exploration Areas and Advanced Exploration Prospects -are specifically reviewed. The pitfalls in adopting a ""recipe"" approach are noted. It is the author's view that the Expected Value Method (based on the probability adjustment of the output of a Discounted Cash Flow/ Net Present Value model) has little application in the valuation of exploration mineral assets, so it is only briefly addressed. The methodologies reviewed are listed below. ò Multiple of Exploration Expenditure Method (expenditure based). ò Joint Venture Terms Method (expenditure based). ò Geoscience Rating Methods (eg Kilburn - area based). ò Comparable Market Value Method (real estate based). ò Rules of Thumb (eg $/Resource or production unit; % of in situ value). Some recent Prospectuses are used to provide examples of their misinterpretation and misapplication.

Jan 1, 1994

By McAllister J

Oxygen was in restricted use at Port Kembla until tonnage oxygen became available for steelmaking in the open hearth furnaces. In adopting the new process various modifications to furnace design and operation were necessary and some of these, including increase in roof height and variation in firing and draft control, are discussed.The design of oxygen lances is also discussed and various steelmakingtechniques considered.Steel production increased with oxygen roof lancing-one- furnace producing 8,507 tons in one week-but new problems, such as rate of refractory wear, and disposal of fumes, were created.Design of future open hearth oxygen furnaces is predicted.INTRODUCTIONIn the post-war era, the availability of "tonnage" oxygen caused a major revolution in steelmaking techniques. Various pneumatic processes showed that steel can be madeat a very fast rate and that oxygen steelmaking can be applied to open hearth furnaces. Methods used are surface impingement with roof lances, bath injection with door lances, flame enrichment with fuel firing, mixed gas and oxygen firing, and enrichment of normal combustion air by oxygen injection into the flue systems.Owing to its previous restricted availability and high cost, oxygen was used in rather small quantities in the open hearth furnaces at Australian Iron and Steel Pty. Ltd.(A.I. & S.), Port Kembla, until about the middle of 1960.At that time tonnage oxygen became available and roof lancing commenced on No. 33 furnace at No. 2' open hearth shop.

Jan 1, 1962

By D La Rosa, A Jankovi, A Dance, W Valery

This paper presents the methodology for optimising blasting and comminution processes in terms of fragmentation developed by Metso Minerals Process Technology Asia-Pacific and South America (MMPT). The methodology is called process integration and optimisation (PIO) and involves a number of steps: benchmarking, rock characterisation, measurements, modelling/simulation of blasting and comminution processes and where required, material tracking. The measurements collected while at site are combined with rock characterisation and definition of ore domains to model the complete process chain. These data are used to develop site-specific models of blast fragmentation, crushing, grinding and flotation. This allows customised blast patterns to be developed that optimise both crushing and grinding performance. For each domain, blast designs are recommended to generate the optimal fragmentation size for downstream processes. The objective is to minimise the overall cost for the entire process and the changes often have a positive impact on the mining operation. Process constraints such as wall stability, ore dilution, muck pile characteristics, size of mining equipment, size and installed power of crushing and milling equipment and other process bottlenecks are considered in the blast designs. This methodology has allowed many operations around the world to significantly increase their production: generating typically five to 20 per cent higher concentrator throughput. A number of case studies will be discussed in this paper to describe the structured approach taken and demonstrate the benefits that are achievable. This paper will focus on the role of blasting in the optimisation of the entire mine to mill process chain and discuss elements of the PIO methodology: rock characterisation, fragmentation modelling and measurement, the relationship between fragmentation and mill throughput and material tracking.

Jan 1, 2007

By N Meyer

This paper presents a research project referring to the stability of submerged walls of open pit mines and the actual state of development. Obviously the slope stability analysis is always a rather complex problem, because it is difficult to reduce the problem to a design scheme and to define the available in situ soil strength. Especially the design of submerged slopes represents a problem. The state-of-the-art slope stability analysis is based on a simplified modelling of slope failure and soil behaviour and with this predicted stable slope inclinations of sand slopes below water-table are less then half the angle of internal friction. Slope angles calculated like that canÆt satisfy the mining companies. One of the problems that have to be solved is the reliable determination of the long-term stability of non-cohesive, submerged slopes, which is not only dependant on geotechnical and hydrogeological parameters of the subsoil, but is also significantly influenced by how the slopes are made. The research project points at the relations between mining and geotechnical engineering with the main aim to find a more suitable stability analysis which takes both soil behaviour and mining influences into account.

Jan 1, 2003

The Youga gold mine in Burkina Faso, West Africa, is scheduled to produce first gold in the third quarter of calendar 2007. The project is expected to produce 540 000 oz of gold over 6.5 years, from a conventional open pit carbon in leach mine. The direct capital cost of the project is US$47 M. Etruscan Resources Inc, a Canadian based gold exploration and development company, holds 90 per cent of the project company Burkina Mining Company SA (BMC). The state of Burkina Faso is free-carried for the remaining ten per cent of BMC. RMB Resources Limited, of Melbourne Australia, has arranged a US$35 M project finance facility for BMC (the Borrower) as the majority of funding for the Youga project development. The loan facility was provided by RMB Australia Holdings and Macquarie Bank Ltd (the Lenders) each as to 50 per cent in the lending syndicate. The Lenders also provided a gold hedging facility to guarantee a minimum price for the projectÆs gold production. Burkina Faso is a francophone country, part of the Economic and Monetary Union of West Africa (UEMOA). The project financing is the first such facility to be arranged for a mining project in Burkina Faso, with little or no precedent available in other UEMOA countries. Therefore, while the Youga gold project is forecast to be a robust project applying conventional mining and processing methods, a number of legal, technical, commercial and social issues required identification, evaluation and resolution before the loan could be established. This paper describes that evaluation process and the resolution of these issues. In-house experience and expertise in both the LendersÆ and BorrowerÆs teams has facilitated a greater understanding and æownershipÆ of the issues and hence provided comfort with risks which might not normally be taken in conventional project developments and project financings. As a result, blanket external reviews were not required by the Lenders. A long-standing relationship between Etruscan and RMB Resources also facilitated solutions to a number of issues. Nevertheless, a degree of flexibility by the Lenders, the Borrower and Etruscan was required to successfully close the financing.

Jan 1, 2007

In November, 1967, a four strand curved mould continuous casting machine coupled with a 50 ton basic oxygen furnace began producing billets for the rod mill and new merchant mill at the Newcastle Steelworks. To date over 500,000 tons of carbon and alloy steels have been cast at the rate of 20,000 tons per month, the major part for the wire industry. Many alterations have been made to the plant to simplify the process, improve quality and increase production. Casting parameters have been developed for each different type of steel. The quality of the final product has been influenced most by casting temperature, secondary cooling and casting speed. All these factors have been controlled and good results are reproduced. More exacting requirements of liquid steel quality have brought about the use of higher lime/silica ratio slags during steelmaking to control phosphorus revers- ions and standard ladle additions of manganese suicide and ferro aluminium for more effective deoxidation.

Jan 1, 1972

As near surface deposits are increasingly mined out and pit widths beginto exceed the reach of practical direct-casting stripping machines, high haulage costs can make truck-shovel pre-stripping operations uneconomic. This is compounded because the rate of inflation for diesel fuel oil, lubricants, tyres, etc. exceeds the general rate of inflation. The use of conveyor transport systems, long established in terracemining operations in weak materials, e.g. engineering soils, can provide a viable haulage alternative in pre-strip operations and in some open pit settings. The paper describes the engineering requirements and basic economics of such systems.

Jan 1, 1985

By B Delaney

For worker safety, mining companies are required to stop production and inspect hoist ropes. Visual inspection is generally done daily and EM inspection occurs every three to four months. During visual inspection, rope speed is generally reduced so an inspector can look for problems. In EM testing the LMA and LF traces are printed on a paper strip chart and a skilled operator interprets these traces. Mining companies only find large defects during visual inspection and are sometimes concerned about the content of EM trace information. This paper will present research outcomes that show how muck can be hoisted while performing a complete visual rope inspection at full speed. Other research results will show that digital signal processing can increase the amount of information available to the EM rope inspector. The research was funded by Inco, C-CORE, three AMIRA International sponsors and six sponsors from the Canadian Deep Mining Research Consortium (DMRC). The research will be commercialised in 2005.

Jan 1, 2005

By Wymer DG

The concept of hydro power in deep mines is based on the exploitation of the hydrostatic head that can be gained as refrigerated cooling water descends in shaft pipe columns from the surface, to provide hydraulic power for machines at the working face. This paper describes the work done on two important aspects of the controlled distribu-tion of the high pressure water within a mine, namely the control of pressure under normal operating conditions, and the control of flow in an emergency situation following a pipe breakage. Suitable methods of control have been determined using theoretical techniques to model the steady and unsteady flow behaviour of the water in the pipeline, and taking into consideration the environmental constraints on the types of control devices that can be used. The preferred approach is one in which the high pressure water itself is used as the control medium. The control valves themselves can be fairly conventional in design, but in the case of pipe break protection it is shown that a less conventional approach based on the use of a hydraulic fuse gives improved control performance.

Jan 1, 1985

By R Austerberry, S Green

Highly weathered ground, limited collar options and the need to achieve a desired outcome at the lowest possible cost led to the need to adopt a construction approach that had no established design methodology. The newest ventilation shaft at Mandalay Resources’ Costerfield Operations had to be established to a depth of 30 m through poor ground best described as ‘sticky swelling clay’, some of which was contained within an old backfilled pit.The ability to excavate a traditional presink was not possible due to limited space and the introduction of men into the shaft was to be avoided due to the associated safety risks and corresponding increase in cost. Piling in conjunction with raise boring and remote fibrecrete application was identified as a possible solution that could achieve the desired outcome at an acceptable level of risk.Construction of the piles was challenging and required continual refinement until an acceptable level of productivity could be achieved. Limitations on concrete delivery was taken into consideration to ensure hole stand-up time was acceptable and re-drills were not required. The adoption of a set process from alignment, drilling, concrete placement and testing ensured the desired design was achieved. Mine operators should consider the use of piling as a method of shaft stabilisation for the portion of raise bored shaft that passes through the weathered zone.The importance of quality control and attention to detail through the entire shaft construction process cannot be underestimated as issues such as insufficient geotechnical investigation, pile and pilot hole deviation, concrete and fibrecrete quality, as well as delays in the application of fibrecrete can place the success of the project at risk.This paper outlines key learnings from a client’s perspective with regards to the concept, planning, design, execution and completion of a 3.1 m diameter raise bore shaft through both weathered and highly structured ground at the Augusta Mine.CITATION:Green, S and Austerberry, R, 2014. Piling and raise bore construction – key learnings from a client’s perspective, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Evans A. F

Arising out of the increasing demands for efficiency in modern ore-dressing operations has grown a requirement for fuller knowledge of the characteristics of the ore treated. In part, this is being met by improved methods of study of the mode of occurrence of the constituent minerals, and of the intricacies of their physical relationships.A typical instance of the need for such a study is the presence of some undesired mineral in a flotation concentrate or tailing, which may be due either to mechanical association through insufficient grinding, or to incomplete separation in the flotation operation.Again, with modern practice in fine grinding, which often requires that from 70% upwards of the ground ore shall pass a 200-mesh screen, it is obviously impossible to obtain data on comparative grinding efficiencies, for instance, unless there is adequate knowledge of the size-composition of the material passing the finest available screen.Studies like these can be made satisfactorily only after size-separation (which may be carried out conveniently by elutriation) and by actual visual examination with the aid of a microscope, and the minute size of the mineral grains to be examined has necessitated the development of a new technique of sizing and microscopic examination.

Jan 1, 1932

By S M. C Verryn

Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis of metallurgical products. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine process control. Knowledge of the crystal structures of the major phases is essential for Rietveld analysis, and these are well known for most minerals and major phases in metallurgical products. It provides the basic structural information necessary for the determination of mineral stoichiometry and for elucidating solid solution behaviour. Modern methods, such as simulated annealing and charge flipping, permits the determination of crystal structures from powder data. Unit cell data can be used where conventional microchemical analysis is unable to provide an answer to the extent of solid solution in ilmenite roasting. Unit cell data (by XRD) is used to determine the amount of roasting necessary for the development of magnetisation to be able to separate chromite from an ilmenite concentrate. Phase quantification is probably the most widely used application of XRD analysis. It is used for materials balance in the minerals and cement industries, and it is finding novel applications in the iron and steel industry. Applications of XRD in high-temperature metallurgical processes are increasing. In this paper the phase chemistry of iron ore sinters, the evaluation of subsolidus reactions in titania slags and the identification of furnace accretions are discussed. Despite the success of the Rietveld method in phase quantification, the method still needs further development in the quantification of closely related or polytypic phases. The quantification of pyrrhotite phases using various Rietveld programs still gives ambiguous results. This is also true for the different SFCA phases in iron ore sinters. Clearly the analysis of similar phases, differing only in the presence of weak superlattice reflections is still problematic.

Jan 1, 2008