Search Documents

By M A. Tuck

Atmospheric air on a moisture free volume basis consists of approximately 21 per cent oxygen. The current minimum threshold for oxygen in Australia is 19.5 per cent. Atmospheric air generally will also contain water vapour and will also pick up further moisture as it flows around a mine ventilation network. This paper details the results of a study to determine how much oxygen depletion can occur due to the sole impact of increasing the moisture content of air and the potential impacts of this on ventilation system design. The study shows that the moisture content can have a significant impact on the oxygen concentration in mine air. The main factors controlling the impact are the barometric pressure, dry bulb temperature and relative humidity of the air.CITATION:Tuck, M A, 2015. What is the oxygen depletion potential of ?water vapour?, in Proceedings The Australian Mine Ventilation Conference, pp 173–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By P G Simpson

The Sundance gold mine, located 2.5 km east of the town of Batchelor in the Northern Territiory, has produced over 5300 oz of gold since it was discovered in 1978. Sundance is unique in the Pine Creek Inlier in that the ore is hosted in palaeo-karst detritus and crystalline magnesite of the Early Proterozoic Coomalie Dolomite. This paper presents a summary of the geology of the mine, and describes the methods used during the two periods of mining.

Jan 1, 1994

By A Hilli, K Kosmara, J Steyn

PT Nusa Halmahera Minerals (PT NHM) is an Indonesian joint venture company owned by Newcrest Mining Limited (75 per cent) and PT Aneka Tambang (Persero) (25 per cent). PT NHM operates two underground gold mines, Kencana and Toguraci at the Gosowong mine site in North Halmahera District, North Maluku Province, Indonesia.On 8 February 2016, a major ground movement occurred in the K-Link orebody of the Kencana underground mine, effectively blocking the only two access ways to the stoping area. Following mine clearance, it was found that a Solo production drill rig operator, who had been drilling in the Level 10 Extraction Drive was still underground, cut off from the rest of the mine by the ground movement.Communication, nutritional and logistic supply to the trapped operator was established with the breakthrough of two diamond drill holes. A range of technical expertise and opinions from both on and off-site were sought and two options were chosen for implementation of the rescue operation. The rescue was completed successfully on 16 February 2016 with the operator being rescued in good physical and mental health.CITATION:Kosmara, K, Hilli, A and Steyn, J, 2017. Eight days entrapped – PT Nusa Halmahera Mineral’s rescue of a trapped miner, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 155–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Toussaint LF

A brief history of the mineral sands industry is given from a radiation protection standpoint, with gamma radiation and inhalation of radioactive dust being identified as the main sources of radiation exposure of persons working in the plants. The principal sources of gamma radiation exposure are identified and the history of early bagging methods is discussed. The concept of ALARA is introduced and the impact of the "bulka bags" (and more effective monazite storage facilities) are detailed as illustrative examples of dose minimization, together with the requirements for the transport of monazite. The dose from radiation received from inhaled dust is dependent on a number of parameters of the dust, some of which are not well known. ICRP 30 (1978) makes recommendations relating to the intake of radionuclides by workers. These recommendations are discussed with respect to the inhalation of dust containing thorium. The possible pathways of radioactive material throughout the body are also described. The effect of having parameters that differ from ICRP 30 is discussed and suggestions are made relating to measurements that can be carried out to more accurately determine these parameters. Since in some instances the exposures to dust yield personal doses which may exceed the annual ICRP 30 based limits, it is necessary to define more accurately parameters of the dust so as to determine more accurately personal Doses.

Jan 1, 1986

By S F. Wang, J J. Yin

Dust pollution poses a persistent challenge within mining processes, giving rise to a spectrum of concerns, including occupational diseases, mechanical degradation, diminished visibility, and the potential for dust explosion incidents. Existing dust detection and monitoring methodologies face limitations, including insufficient measurement accuracy and intricate processing procedures. Consequently, a comprehensive identification and evaluation system rooted in image processing technology is proposed to facilitate real-time measurements of dust pollution in mining worksites. The study primarily employs grey scale average and fractal dimensions to characterise particle features evident in collected dust images. As a result, the data processing platform can dynamically process data and present dust pollution conditions. Notably, this research integrates the monitoring and assessment of dust pollution with the systematic adjustment of mining parameters, ventilation parameters, and strategies for dust reduction. Through statistical analysis of dust concentration and particle size during mining processes, rock properties such as components and cuttability can inform mining parameters. This information, in turn, guides detailed excavation strategies, including cutterhead speeds, torque, and excavation speed. Similarly, analysing dust characteristics derived from images is a valuable resource for gaining deeper insights into the efficacy of implemented ventilation strategies. By harnessing vision-based information detailing dust concentration and distribution, a wealth of direct guidance becomes available for refining ventilation parameters. This encompasses crucial aspects such as the selection of appropriate ventilation systems tailored to the specific mining environment and the optimisation of operational conditions for ventilation fans. Additionally, the detailed information derived from the visual data allows for strategic decisions on factors like the spatial arrangement of ventilation outlets and the calibration of airflow rates. Moreover, precise choices for dust reduction measures and parameters can be made based on the prevailing dust conditions. Upon real-time monitoring of dust pollution using the proposed method, corresponding measures such as spraying and foaming can be promptly implemented. Crucial parameters, such as spray angles and volume, are integral to these application processes. In essence, the proposed method assumes a pivotal role in not only dust monitoring but also the formulation of preventative and control measures within mining processes.

Sep 1, 2024

By Lawson E, Purkiss S. A R, Van Ashwegen p C

It is only in the past decade or so that industrial exploitation of biological resources and techniques has become regarded as a distinct discipline. Commonly referred to as Biotechnology, it embraces biochemistry, microbiology and the engineering sciences and is mainly aimed at the biological conversion of suitable raw materials into desired end products. The catalytic agents are more often than not bacteria although other micro-organisms such as fungi are used. The range of micro-organisms used is wide and the choice depends upon the desired end product, which in turn depends upon the metabolic attributes, genetically engineered or otherwise, of the cells. The metabolic diversity of micro-organisms has been applied to processes such as antibiotic production, food processing, brewing and chemical production, and of course extraction of metals from ores. Metabolic diversity is, to a certain extent, based on nutrition, which, in its simplest form, can be divided into energy source, carbon requirements and nature of the electron donor producing reducing power to the cells. The source of energy may be light, in which case the organisms are phototrophic (eg green plants, algae). The carbon requirements and reducing power may come from organic sources. These organisms are then called heterotrophic (eg man and most bacteria, including the well known Escherichia colt). However, there is a group of bacteria whose energy metabolism depends upon chemical redox reactions, use inorganic carbon (CO2) and obtain their reducing power from reduced chemicals such as metal sulphides. These are known as chemolithotrophs. They play an important role in mineral recycling in nature and are also ideal for extraction of metals from ores. This is because they are extremeophiles being acidophilic (grow at very low pH) and sometimes also thermophilic (grow at very high temperatures). These bacteria operate in such hostile environments that competition, or contamination, by other organisms does not occur. Extraction of metals from ores by chemolithotrophic bacteria is commonly referred to as biohydrometallurgy. Other related areas are bioadsorption of metals from dilute solution,- microbial treatment of metal contaminated wastes and removal of toxic chemicals produced or used during mineral processing. This paper basically reviews the work that Gencor has undertaken in the field of biohydrometallurgy and the advancements it has made in commercialising the technology, but also touches on certain long-term areas of research that are currently under investigation.

Jan 1, 1995

By J Mauk, J Rowland

The Karangahake epithermal Au-Ag mine consists of two main lodes, the Maria and the Welcome/Crown hosted in Miocene andesites. Mineralisation is strongly constrained to major structures and is genetically linked to dynamic tectonic processes. Two main periods of faulting are represented in the deposit: 1. NE striking right-lateral/normal oblique linked spatially and temporally with the mineralising system, and 2. ESE striking right-lateral/normal oblique post-mineral faulting that displaces the lodes. Paleostress analyses performed on a limited kinematic data set indicate NW-SE extension during the formation of the vein system. Veins and lodes strike NNNE and accordingly contain a strike-slip component. The kinematics of vein formation at Karangahake is broadly consistent with that of other deposits within a NNE-trending belt of deposits. Oblique shear on deflecting structures will create zones of compression and dilation. Dilatant zones created on steep structures create fluid pathways potentially focussing large volumes of fluid from deep parts of the system into dynamic structures.

Jan 1, 2003

By M S. Manono, K C. Corin

The optimisation and process developments surrounding the beneficiation of Cu-Ni-PGM ores is of fundamental importance when considering the continued rise in global demand for these precious metals. The selective sequential flotation of these ores is accompanied with various processing challenges such as the successful separation of the Cu-Ni-PGMs from non-sulfide naturally floatable gangue and pyrrhotite. Reagents such as sodium iso-butyl xanthate (SIBX) and sodium carboxymethyl cellulose (CMC) have proven to significantly improve the selectivity of the flotation process in their respective roles. The use of recycled water with abnormal inorganic electrolyte concentrations can modify the selectivity of these reagents, as ions may adsorb onto minerals such as pyrrhotite, thereby hindering or promoting the hydrophocity and floatability of pyrrhotite. Process water quality effects on the behaviour of pyrrhotite may have negative or positive influence on the recovery and grades of the wanted Cu-Ni-PGMs as valuable minerals associated with pyrrhotite such as pentlandite may be affected in like manner. Thus, the impact of concentrator process water quality on the behaviour of pyrrhotite needs to be determined. In this study synthetic process water at various ionic strengths was investigated against various CMC dosages to understand the behaviour of pyrrhotite during the flotation of a Cu-Ni-PGM Merensky ore in a batch flotation cell. This study showed that pyrrhotite grades increased with an increase in CMC dosage for fixed ionic strengths whereas the recoveries of pyrrhotite increased with an increase in ionic strength until 3SPW, then a trend of a decrease in recoveries was seen with 5SPW resulting in the lowest pyrrhotite recoveries. Furthermore, this study showed that moderate CMC dosages of 100 g/t resulted in the highest pyrrhotite recovery for all four ionic strengths of synthetic process water tested. It can be said that to maximise value recovery from Cu-Ni-PGM ores, understanding the behaviour of pyrrhotite against degrading water quality and reagent suites could be of paramount importance given the sensitivity of pyrrhotite to oxidising chemical conditions.

Aug 24, 2022

By N Burgio

Block cave mines are often thought of as rock factories where high volumes of production are mined from a fixed area suggesting little requirement for geological input and control. Yet caving operations have peculiar and specific technical requirements from prefeasibility through to post-mining reconciliation. Whilst essential elements such as resource definition, geological interpretation and sampling strategies are common to all mining methods, planning for a block cave requires a different emphasis and philosophical approach in how we deal with these issues. We will examine why a geoscientist’s input is critical towards the successful planning, design and monitoring of a caving operation.

Aug 22, 2011

By T Kon, K Ohno

Slag foaming is an important control item in the process of refining molten steel. This study aims to investigate the factors controlling slag foaming by observing the bubble formation behaviour resulting from the chemical reaction between iron oxide and Fe-C alloy in the slag. In this study, 0.06 g of Fe- C alloy was introduced at the bottom of a BN crucible, and 6.0 g of slag (SiO2:CaO:Fe2O3 = 40:40:30) was placed on top of it. The crucible was positioned inside an infrared image heating furnace, where the temperature was rapidly raised to 1370°C at a rate of 1000°C/min in a nitrogen stream, and then held at that temperature for a predetermined time before rapid cooling. Following rapid cooling, the internal structure of the sample was examined using a high-resolution X-ray CT device. The spherical equivalent volume was calculated based on the number of observed bubbles and their equivalent circle diameter. Additionally, the relationship between the volume ratio of small bubbles in the slag volume and the distance from the bottom of the crucible was determined, along with the calculation of bubble density and volume ratio. Under various experimental conditions, numerous bubbles with equivalent circular diameters ranging from 200 to 300 μm were consistently observed. The density and volume fraction of bubbles with circular equivalent diameters between 200 and 500 μm showed a tendency to increase as the distance from the bottom of the crucible increased. Bubbles with equivalent circular diameters of 500 μm or more consistently exhibited lower bubble densities, regardless of their height within the crucible. The formation of larger bubbles is attributed to a decrease in iron oxide concentration within the slag as the reaction progresses. However, this is believed to be due to their higher buoyancy, resulting in shorter residence times within the slag and a reduction in the number of encapsulated bubbles.

Aug 21, 2024

By C V. Deutsch

"Geometallurgical variables often cause problems to conventional geostatistical workflows. There are many variables; some are compositional and some are non-additive. They often show: complex multivariate relationships undersampling relative to conventional grade variables unequal sampling; that is, all variables are not available at all data locations.A variety of approaches have been developed over the years, but geostatisticians remain mostly focused on modelling rock types and a few grade variables with an abundance of data. The problems are reviewed and a chained workflow is presented where appropriate techniques are employed in sequence to permit reliable spatial prediction of geometallurgical variables. The spatial models may be used to assess the value of additional data, for prediction of process performance, for improved mine planning and other optimisation tasks. The chained workflow will include data transformations such as ratios and normal scores that make the variables amenable to geostatistical modelling. Data imputation techniques to account for missing values are considered with special consideration to spatial correlation with the available data. Decorrelation techniques such as the principal components, min/max autocorrelation factors and projection pursuit multivariate transformation are employed to manage massively multivariate modelling. Full distribution modelling must be considered to avoid biases in the prediction of non-additive variables. The post-processing of geometallurgical models must be streamlined for robustness and efficiency. The precise workflow varies according to the specific purpose of the study. Guidelines and thoughts on best practice are presented.CITATION:Deutsch, C V, 2013. Geostatistical modelling of geometallurgical variables - problems and solutions, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 7-16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By D Giurco

As part of global systems of mineral production and consumption, the Australian minerals sector is facing sustainability challenges across technological, social, ecological, economic and governance domains, as well as between local, national and global scales. To ensure that the Australian minerals sector progresses towards sustainability, it is imperative to understand the possible ways in which AustraliaÆs mineral resources could support sustainable futures. A significant research gap exists between the complex nature of questions concerning minerals sustainability and the reductionist methods available to deal with them. This paper argues the need for broader, more integrated approaches to questions concerning minerals sustainability, which can address multiple human perspectives, complex and æmessyÆ patterns and processes across multiple organisational, temporal and geographical scales and whole systems of mineral production and consumption. To inform the development of a new approach to minerals sustainability, this work reviews the contemporary understanding of the Australian minerals sustainability problematic, from the perspective of the Australian minerals sector (Minerals Council of Australia), the Australian research sector (Mudd 2007a, 2007b; Mudd and Ward 2008) and a multi-scale international project (MMSD 2002). This review shows the focus of current responses to the minerals sustainability problematic, identifies the need for an integrated approach to questions of minerals sustainability and addresses how different approaches are informed by underlying and unarticulated assumptions about the tolerability of tradeoffs between different societal goals, the treatment of uncertainty and the application of different conceptual geographical, organisational, temporal and life cycle scales to define the minerals sustainability problematic. The Mineral Resources Landscape proposed, offers an expanded conceptualisation of minerals sustainability, to link minerals production and consumption in an integrated assessment across the entire minerals supply chain, connecting social, ecological, technological, economic and governance domains across local, national and global scales. The key leverage points governing change in the Mineral Resources Landscape are identified as: the material source, extraction and production technologies, level of service and value, and consumption patterns. Mapping the key challenges facing the minerals sector, as identified in the review herein, indicates that the boundaries defining traditional conceptualisations of minerals sustainability focus on the material source and technology and ignore two very key drivers of the Mineral Resources Landscape û the æservicesÆ minerals offer to society and the æconsumption trendsÆ which assimilate these services into society. Understanding these overlooked aspects of the Mineral Resources Landscape, along with the conventional areas of focus, is essential for identifying the Australian minerals sector as a provider of sustainable mineral services. This insight prompts a reconsideration of the role of minerals services and consumption trends, together with the role of the material source and technology in shaping change and the emergence of sustainable systems of Australian minerals production and consumption, across multiple scales and domains.

Jan 1, 2009

Water Savings and Coal Product Compromise

Sep 13, 2010

Current NSW Government policy requires searching for more than just minerals during an exploration program - add endangered fauna and archaeological relics for a start.

Jan 1, 1995

The seemingly insatiable world demand for mineral and energy products is continuously pushing out the frontiers of exploration and development in countries around the Pacific Rim.

Jan 1, 1990

The degree of ionicity-covalency of complex compounds is discussed here as a prospective criterion for selection and purposeful synthesis of sulfhydril and oxhydril collectors. Theoretical predictions of flotation behaviour were confirmed by flotation of a number of ores.

Jan 1, 2005

The paper examines the current status of risk and accepted practice in mining geomechanics. It explores some deficiencies in human capital, risk analysis and our future technical needs, and suggests ways of improving our estimates of slope reliability through knowledge sharing and research.

Jan 1, 2003

This paper looks at the development in management education for engineers at the undergraduate level with particular reference to mining engineers. The management core content of the engineering degree course at Ballarat C.A.E. is described is some Detail.

Jan 1, 1986

By Bojcevski D

The deportment and textural relationships of silver bearing phases are key characteristics in understanding the behaviour of silver ores in flotation tests or processing plants. These characteristics are however difficult to define and quantif

Jan 1, 1997