Search Documents

By J. P. Harrison, N. Bozorgzadeh, M. Dolowy-Busch

"It is common in rock engineering practice to characterize the triaxial strength of intact rock by using only data samples of small size. Practical guidelines such as ASTM support such sample sizes. In this paper, we investigate the reliability of the Hoek-Brown strength criterion estimated from such samples. For this purpose, we use an unusually large published set of triaxial strength data to randomly select a large number of data samples of small size to simulate the situation that frequently encounters in practice. The samples are generated with different arrangements with regards to the confining pressure. We fit the Hoek-Brown criterion to each of these samples, obtain estimates of strength parameters and compare them to those obtained from the complete data set. Our analysis suggests that estimates based on small samples are not reliable and can lead to both over- and under-estimation of strength.Additionally, we use these small samples to investigate the statistical methods for obtaining design values of strength as suggested by limit state design standards such as Eurocode 7. We show that, if used in conjunction with small samples, these methods do not guarantee a safe estimate of strength and in many cases lead to highly over-conservative estimates.We present a potential solution to this problem by augmenting the small data sets with Bayesian informative priors to give much more reliable estimates of strength. We conclude with suggestions for the development of informative prior distributions."

Jan 1, 2015

By Kristie Tarr

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

Oct 1, 2010

By Stephen R. Grano, Jon Glatthaar, Philippe Steinier, Christopher J. Greet

"The importance of the oxygen content of sulphide mineral pulps in determining which reactions occur, and their subsequent influence on flotation behaviour is grossly underestimated in most operating concentrators. While pH is routinely monitored, Eh and dissolved oxygen measurements are obtained infrequently. However, dissolved oxygen measurements in conjunction with other pulp chemical parameters (i.e. pH, Eh, and EDTA extractable metal ion analysis), can provide valuable insight into where and what type of reactions are occurring within a circuit. Unfortunately, these readings yield “instantaneous” measurements of the pulp chemical parameters.What is needed is a means of establishing how reactive a pulp is, and how this reactivity changes as components of the system are manipulated. Oxygen demand provides an opportunity to do this. Several attempts at measuring the oxygen demand of a pulp have been made in the past with varying degrees of success. Most notable among these are Noranda and BOC Gases.Learning from these experiences, Magotteaux have developed the MagO2 ® demand vessel to measure the oxygen demand of mineral pulps. This paper described the apparatus, and through a case study on Broken Hill lead/zinc ore demonstrates how the MagO2 ® demand vessel is used.INTRODUCTIONThe role of oxygen in flotation is complex. While a considerable body of work exists demonstrating the strong involvement of oxygen in the interactions between sulphide minerals and collector (Gaudin and Finkelstein, 1965; Gaudin, 1974; Woods, 1984; Laajalehto, Nowak and Suoninen, 1993), the presence of oxygen can also affect the oxidation state of sulphide and non-sulphide minerals, which can impact on their flotation behaviour. Further, sulphide mineral oxidation is related to their oxygen demand (Spira and Rosenblum, 1994)."

Jan 1, 2004

By P. Wanjara, M. Xiao, M. Jahazi, C. Poon

Using a robotic 4kW Nd:YAG-laser system, Inconel 718 (1 mm sheet) was welded with and without filler wire to investigate the effect of processing parameters, including power input and welding speed, on the weld geometry, microstructure and mechanical properties. By means of both nondestructive testing and microscopic examination, the weld quality was studied to determine the nature of the welding defects (porosity, cracking and bead shape) over the processing range of 3-3.5 kW for the power input and 4.5-6 m-min-1 for the welding speed. Application of the design of experiment methodology permitted the examination of the relationship between the process parameters and mechanical properties, from which the optimized laser welding conditions could be determined for joining Inconel 718. In particular, the research results indicate that Nd:YAG-laser welding technology can achieve defects free, mechanically sound welds with narrow fusion and heat effected zones.

Jan 1, 2006

By Dr. Rory Cameron, Dr. Terry Cheng, Dr. Nadia Mykytczuk, Ian Bedard, Kristie Tarr, Ruth Joseph

Pyrrhotite-rich tailings from Sudbury, Ontario mining activities are known to contain significant amounts of EV metals, such as nickel and cobalt.  CanmetMINING has developed a novel bioleaching process for recovering the nickel and cobalt (both critical for vehicle electrification) from tailings that incorporates partial neutralization and iron removal in the bioleaching circuit; bench- and pilot-scale tests have resulted in excellent nickel and cobalt recovery over a range of temperatures.  However, this process generates a new bioleach residue, which is heavier and more voluminous than the original tailings due to pyrrhotite oxidation and jarosite formation during the bioleaching process. This residue can be problematic for long-term disposal. A possible solution being studied for this issue is using mine backfill as a disposal mechanism.  Underground backfilling allows for effective re-purposing of mine waste, however the backfill must also be able to withstand a certain load, since in most cases it is used as an underground construction material, such as in cut-and-fill mining methods.  Therefore, the composition of the mill tailings must be such that when combined with a binding agent and pumped underground, the slurry or paste is then able to withstand a certain load within a certain period of time.  Unfortunately, high-pyrrhotite content tailings, commonly found on mine sites in Ontario and Quebec, are reactive and can easily oxidize and produce acidity and/or metal-laden drainage under some disposal conditions. This means that the pyrrhotite in the tailings can lead to acid mine drainage if stored on surface, however, it can also cause strength degradation if re-purposed in too high a concentration in underground mine backfill.  The research being done at CanmetMINING related to the bioleaching process is aimed not only at recovering nickel and cobalt from mine tailings, it is also being used in an attempt to neutralize the tailings to reduce acid mine drainage and backfill strength degradation. This paper reports on research designed to evaluate different options for transforming the bioleaching process residue into iron oxide phases, for better environmental footprints if stored on surface, as well as increased disposal possible, if re-purposed as underground mine backfill material.  

May 4, 2025

By Adam Jordens

Along with gravity separation and froth flotation, magnetic separation is one of the most common techniques for separating minerals. Minerals are separated by a magnetic force that is dependent on a combination of the applied magnetic field, the magnetic field gradient and the magnetic properties of the minerals themselves. Minerals may be classified as diamagnetic, paramagnetic or ferromagnetic based on the way they interact in a magnetic field. The magnetic susceptibility of a material may be determined by using a vibrating sample magnetometer to determine the magnetic moment of the material in an applied magnetic field and then converting this measured moment into the material?s magnetic susceptibility. In the case of rare earth minerals, magnetic separation is commonly used to remove ferromagnetic iron-bearing gangue minerals and to concentrate paramagnetic valuable minerals such as monazite and xenotime. These magnetic separation steps are frequently preceded by a gravity separation step as many iron oxides and rare earth minerals have specific gravities that are much larger than those of typical gangue minerals. By varying the magnetic field intensity it may be possible to use magnetic separation to selectively separate the paramagnetic and ferromagnetic minerals that report to the concentrate after gravity separation. Test work on a Canadian rare earth ore has shown that a gravity concentration step using a Knelson concentrator was able to selectively concentrate heavy magnetic minerals as evidenced by increased recoveries, relative to the Knelson tailings and fresh feed, after processing through a wet variable intensity magnetic separator. Mass pull to the Knelson concentrate was 4.5 % and the magnetic recovery of this concentrate, at 0.94 T, was approximately 40 % higher than the magnetic recovery from the Knelson tailings (70 % versus 30 %). The products of the wet high intensity magnetic separation were also analysed using a vibrating sample magnetometer to determine the magnetic susceptibilities of the various concentrate and tailings products.

Aug 1, 2013

By Sadough vanini Ali

Hot deformation behavior of functionally graded steel (FGS) was investigated via conducting hot compression tests at different temperatures and strain rates. Functionally graded steels consist of ferrite, austenite, bainite and martensite layers that are made by diffusion of alloy elements during the melting process. The zenerhollomon parameter has been used to describe the flow stress variations as a function of temperatures and strain rates. The parameter values for all the layers via using the boundary conditions was determined based on composite graded behaviors. Furthermore by applying the rule of phase mixtures, the whole strain rate applied on composite would be the sum of layers strain rates considering the layers volume fraction, while the layers have the same stress. Consequently the composite flow stress for each strain rate and temperature was determined.

Oct 1, 2011

"This document establishes standards and guidelines for scientific and technical disclosure by Issuers listed on the TSX Venture Exchange on their mineral properties. It incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.1. Introduction1.1 General(a) This Appendix establishes standards and guidelines for scientific and technical disclosure by Issuers on mineral properties. These standards and guidelines should be applied prudently and with common sense by those Issuers in conjmction with the applicable requirements of section 1.2.(b) This Appendix incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and -written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.(c) This Appendix is not intended to be exhaustive or all-encompassing and greater detail may be appropriate and required in certain situations. Issuers are encouraged to contact Exchange technical staff where they are not certain about the requirement for disclosure on mineral properties."

Jan 1, 2003

By Rocky (Yaokun) Wu

This paper introduces the development and application of a new cable anchor - Cable-Lok for pre-stressed cable bolting in mines. Cable-Lok is a spring-loaded cable anchor suitable for the drill hole diameter of 50 and 65 mm (2" and 2.5") in medium soft rock to hard rocks. The cable anchor is automatically set on installation and the cable can be tensioned immediately to provide active and primary support throughout its length. Post-grouting can be conducted independently. In comparison with the conventional cable bolting, Cable-Lok anchor will greatly speed-up the cable bolting circle and decreases the cost of cable bolting. Cable bolting anchored with Cable-Lok anchor has wide application in mines, e.g. pre-stressed cable bolting in large span drifts and intersections for permanent rock support, or in hanging walls or stopes for temporary support, or cable lace anchoring etc. This paper introduces the principle of pre-stressed cable bolting and the specifications of the Cable-Lok anchor, presented the testing results in laboratory and the application cases in mines.

Oct 1, 2010

"These guidelines set out information on timely disclosure of news releases which are intended to provide, existing shareholders and potential investors, factual information on which a reasoned investment decision can be made.Consider the problems and concerns raised by the following hypothetical news releases:Natural Resource Company""The Company has recently optioned a large and exciting gold property near the ""XXX"" gold discovery area. In describing the property, the Company's independent consultant has said: ""The favourable location of, and some of the results of prior work done on the property give the Company a worthwhile mineral exploration opportunity .... "". The Company proposes to expeditiously conduct a sizeable exploration program on the property as soon as the appropriate financing has been arranged.""Non-Resource Company""Based on discussions with several European countries, the Company anticipates that it will have orders to ship over 200,000 crates of widgets to those European countries over the next two years. These orders, which considerably exceed the Company's forecasts for the first year, represent a projected profit to the Company in excess of $1,000,000 over the next five year period.""GuidelinesTimely disclosure news releases are intended to provide, to both existing shareholders and potential investors, factual information on which a reasoned investment decision can be made. National Instrument 43-101 Standards of Disclosure for Mineral Projects provides requirements for disclosure of a scientific or technical nature for a mineral resource company.The examples do not provide sufficient detail and are misleading because material information is omitted. The following guidelines should be observed when preparing a news release:"

Jan 1, 2003

By S. Rash Ahmadi

One of the most important elements in power plants is rotors and repairing the damaged rotors is very important in view point of economics. One of the most complicated problems in power plants is increasing of stiffness of the turbine rotors. This problem which occurs mainly due to thermal shock or rubbing makes to exit damaged rotor from service. These elements can be repaired effectively by heat treatment methods. Tempering heat treatment is the most common solution for straightening of damaged rotors but it requires having good knowledge about heat treatment parameters (temperature and time) and their affects on fundamental properties of rotors. In this article, a suitable method is introduced in order to modify the increased stiffness in journal part of rotors due to martensite transformation, using heat treatment tempering process.

Oct 1, 2011

By S. Rash Ahmadi

Thin brittle coatings are deposited or developed on component surfaces for different reasons. In many practical applications the coatings are stressed by externally applied loads. Under such conditions, coating failure can occur. In this paper the probability of the extension of surface crack in coated materials due to cylindrical sliding indentation is analyzed. Contact loading problems typically result in multi-axle and strongly inhomogeneous stress fields near the contact surface. This property which strongly affects the stress intensity factors is taken into account in the failure analysis. Edge cracks were selected to model the actually accruing surface flaws. A suitable method is described for calculating the contact stress fields in coating and substrate. The coating is idealized as a brittle-elastic layer of uniform thickness, which is bonded to the surface of a half space. Method of linear elastic fracture mechanics are then used to calculate the load required to cause fracture in the coating.

Oct 1, 2011

By G. S. Hume

"THERE HAS BEEN a marked growth in the petroleum industry in Canada since the end of the war. The rate of growth in the demand for oil products has exceeded that in United States, although the per capita consumption is still less. Estimates of the consumption of petroleum and petroleum products in Canada in 1951 are approximately 154,000,000 barrels, which is slightly more than 11 •barrels per capita, whereas the estimated consumption in United States for the same period, according to World Petroleum, is placed at 2,619,- 970,000 barrels. This, on the basis of a population of 154,000,000, would be equivalent to 17 barrels per capita. The increase in consumption of the petroleum and products is world wide. World production in 1951 has been estimated (Oil and Gas Journal) at 11,700,000 barrels a day or more than 41;4, billion barrels for the year. United States production increased 13.7 per cent to 6,143,000 •barrels a day and Canada'.s ,, total production increased about 65 per cent from a total of 29,091,235 •barrels in 1950 to an estimated (Dominion Bureau of Statistics) 48,096,800 barrels in 1951.The trend to use increased amounts of petroleum and petroleum products, particularly in the United States and Canada, has also been supplemented by increased use of natural gas. The rate of expansion of the consumption of natural gas in United States in the past few years has been very rapid, increasing from 2,600 billion cubic feet in 1940 to 5,975 billion in 1950, with the proven reserves in the same period increasing from 85,000 billion to 186,000 billion cubic feet."

Jan 1, 1952

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

"The standards set out requirements of the Toronto Stock Exchange for company’s providing information to investors, regulators and/or the media regarding their mineral properties. In addition, information contained in new releases, continuous disclosure documents [annual report], or other forms of communication [printed investor relations materials and electronic publications] are also subject to these standards.1.0 INTRODUCTIONThe disclosure of the results of exploration and development activity on mineral properties mustcomply with the requirements of the Toronto Stock Exchange Policy Statement on Timely Disclosure, theOntario Securities Act and all applicable policies and rules of the Ontario Securities Commission and anyother securities regulatory body having jurisdiction over an issuer listed on the Exchange. In particular,the requirements of National Instrument 43-101 must be followed.The purpose of the standards is to set out the requirements of the Toronto Stock Exchange when acompany provides information to investors, regulators and/or the media regarding its properties, whethersuch information is contained in a news release, a continuous disclosure document such as an annualreport, or other form of communication, including, but not limited to, printed investor relations material andelectronic publications such as Internet Web sites. These standards do not apply to prospectuses orlisting applications, the standards for which are contained in the policies and rules of the securitiescommissions and the Exchange. These standards are also not intended to establish requirements for thecontent of technical reports.Any information published by or on behalf of a company must comply with these standards. If acompany becomes aware of information published by others regarding its mineral properties which ismaterially misleading to investors, it should take appropriate action to correct such information orotherwise make it known that it is not responsible for publishing such information and does notnecessarily agree with such statements.Disclosure concerning mineral properties should identify the ""qualified person"" as defined in NI 43-101 who is responsible for the work conducted on the property and such person shall have read andapproved of the technical disclosure."

Jan 1, 2003

By S. Rash Ahmadi

Welding is highly reliable and efficient metal joining process. In welding the metal adjacent to the weld joint is subjected to severe thermal conditions. As a result, complex changes in metallurgical structure occur in this region. These changes in structure depend on the material and the temperature history experienced. Friction stir welding (FSW) is relatively a new welding process in which, heat is generated by friction between the tool and the workpiece. The amount of heat conducted into the workpiece determines the quality of weld, residual stress and distortion of the workpiece. The objective of the current work is to study the transient temperature in a friction stir welding. So, a three dimensional transient analytical model is used to study the thermal distribution during the welding. Heat input from the tool shoulder alone is considered in the model. The process parameters like axial load, welding speed and tool rotational speed, used in actual FSW process are taken to build the model. This analytical model is very useful for select the optimized affected parameters in friction stir welding. The model illustrates the comprehensive equation including actual affected parameters in FSW and it can be used for different materials. In addition to the above the thermal history finds application in design of welding tools.

Oct 1, 2011

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

By A. E. M. Warner, P. J. Mackey

Copper metal is produced in large or small tonnages in almost all countries of the world—handling raw materials in the form of either as-mined or milled ores, custom concentrates, or other custom materials including scrap and recycled copper. The scale of operations and type of technologies used around the world varies widely. There is a certain concentration of both mining and smelter-refinery production as a total of ten countries produce some 80% of world mined copper, while ten countries—mostly different ones— produce about 80% of smelted and refined copper. As a result, international copper trade is significant. The present paper takes the reader on a virtual tour of the copper plants throughout the world with a focus on smelter facilities. Operations and technology employed at each plant visited are discussed including a brief historical sketch. Future trends identified during the world tour are also discussed. The present authors considered sufficient time was required for a thorough study tour and settled on eighty days—the same as that for the celebrated fictional story of world circumnavigation in the 1870s. INTRODUCTION The celebrated French writer Jules Verne published his book “Around the world in 80 days” in English in1873 and it is the story of Phileas Fogg and his French valet Passepartout circumnavigating the world in 80 days in the fall of 1872 on a £20,000 wager (equivalent to over 2 million pounds today) from the exclusive Reform club in London. This is an interesting period for copper as it started trading on the London metals Exchange in 1876 and the start of global copper production chains started to take off at this time with the rapidly increasing electrification of the world. The production chain includes mining, mineral processing, smelting, refining and fabrication. Since 1880 annual world copper production has increased by over 150 times from 154,000 tonnes in 1880 (nominally considered as smelted copper—essentially the only route at the time to marketable copper) to over 23 million tonnes today (including total refined copper of 19 million tonnes of smelted copper including scrap and 4 million tonnes by solvent extraction-electrowinning), in tandem with increased electricity usage, along with significant transportation usage and for manufactured products (Figure 1).

Jan 1, 2019

By J. J. Gillman

"The coal deposits from Cape Perce on Cape Breton Island have been known to supply the coal requirements of the people living in or visiting the area for close to 300 years.A major block of coal has been identified off Cape Perce, which has several seams from which coal can be taken. The initial development by the Cape Breton Development Corporation will be in the Harbour Seam and constitutes the Donkin-Morien Development Project.The CBDC's confidence in this indicated resource is based on its knowledge of the Sydney Coal Field and from boreholes driven into the block during the summers of1977, 78 and 79. In 1980, further geological data were gathered from surface drilling and an intermediate-depth high-resolution seismic survey. The surface facilities for the Donkin-Morien Development Project will be located on the northern half of the cape, with access declines extending 3.9 km in a north-northeasterly direction to the Donkin block of coal reserves. The development has the potential of supplying all the coal needed f or the future electrical power generation requirements of Nova Scotia for many years to come.The planned mine, for which a project definition study has recently been completed, will have a production rate in excess of 3 million tonnes per year.IntroductionAt the Second CIM District 1 Meeting held in Halifax in October 1980, a background paper on Phase II of the Donkin-Morien Development Project was presented. The project involves a 3.2-million-tonne, saleable, underground coal mine. At that time, the chronological sequence of events had unfolded, starting with the initial boreholes through to the feasibility study, and on through site clearing and site preparation. This led to engineering design contracts for the portals and the two tunnels to be driven to intersect with the Harbour Seam close to 4 km from their entry point."

Jan 1, 1982