Search Documents

By S. Foged

Umicore and MWH jointly demonstrated that mechanical dewatering of goethite and neutralised tailings significantly increased the life of a 30 ha tailings pond and improved the operation of the pond. Umicore operates one of its zinc production plants in Balen, Belgium. As part of its production process, an excess of neutralised and goethite¬containing tailings is generated. These have historically been stored inside large lined ponds. As the storage area of the current goethite pond was nearing its capacity, Umicore studied the potential for an extension to the existing embankment. However, this extension would face intense regulatory scrutiny, because the environmental and safety impacts were considered important. Together with Umicore, MWH suggested and investigated an alternative treatment approach consisting of mechanical dewatering prior to storage. A feasibility study was prepared where wet storage was compared to dry storage. Differences in safety risks, environmental impacts and economic costs were outlined. The study demonstrated that the life of the tailings pond could be increased from 6 to 22 years, seriously reducing the environmental impacts and safety risks at no significantly higher cost than would have been incurred with the continued operation of the existing pond. The results of the study are presented in this paper.

Jan 1, 2006

By J. -C. Sztuke, M. Cao

ABSTRACT The correlations between froth recovery of coal and air recovery were investigated using a hybrid mechanical flotation column. The particle slurry was fed onto the surface of air-water two phase froths to carry out the tests. Froth recovery was taken as the recovery of particles into the froth product, whereas air recovery was determined by the froth height method. The relationships between froth recovery and air recovery were nearly linear, with greater slopes for more hydrophobic particles. Inside the froth phase, the particles were stratified, with hydrophobic particles concentrated in the upper region and hydrophilic particles in the lower region.

Jan 1, 2013

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012

By Jack F. McQuat, Ross D. Lawrence

"Most geologists and mining engineers, in the course of their professional careers, frequently become involved with the appraisal of metalliferous mineral deposits and develop a familiarity with and standard approach to the evaluation of these deposits. When the same individuals approach the industrial mineral field, however, their usual approach pattern can be rudely disturbed.This paper highlights the difference in appraisal approach and outlines the factors common to both but which have entirely different emphasis. These comprise geological appraisal, analytical requirements, the importance of transportation, marketing requirements and standards, including appropriate allowances for product development, and marketing penetration.Out of these ""different"" considerations, however, a pat-tern or standard approach emerges which is as common to the industrial mineral field as that used either consciously or subconsciously in the metallic field.The paper reviews the different factors and points of emphasis and offers an outline of the common pattern of appraisal for industrial minerals."

Jan 1, 1971

By N. Novikov, M. Jastrzebski, N. Kryzhanovskaya, D. Shevchenko, I. Kapran, N. V. Novikov, T. Koehler, B. Zaporozhets

"The PFK FeNi Smelter was re-commissioned by Solway Resources in 2002, ending a long period of economic decline in the adjacent town. In 2009 Hatch was retained to design, supply and install a custom furnace crucible that would accommodate a capacity increase from 34 MW to 40 MW and increase campaign life through binding and cooling technologies, as part of ongoing improvement efforts. The involvement of PFK personnel was critical to the successful integration of the new furnace technology with the existing process and operational practice. The furnace upgrade project was completed in 18 months during 2010 – 2011. Since start-up, the furnace has exceeded production expectations, operating successfully at 42 MW.INTRODUCTIONAfter ceasing operations in the 1990’s, the Pobuzhsky Ferronickel Combine (PFK), located in central Ukraine, was stripped of useful equipment and deteriorated while dormant. The surrounding town experienced a period of economic decline throughout the 1990’s. Solway Industries purchased the complex in 2002 and began a systematic incremental program to re-commission the smelter using both local expertise and specialists from other parts of the former Soviet Union. This led to the re-birth of PFK as a successful toll-smelting complex, and a renaissance for the surrounding economy.As part of the continuing improvement program, PFK approached Hatch in 2009 to study the possibility of a capacity expansion from 34 MW to 40 MW. It was decided, based on the results of the study, to design and install a custom furnace crucible integrating the unique PFK FeNi process with modern Hatch furnace technology. This novel approach had many benefits, including: maximum re-use of existing furnace components (off-gas, feed equipment and transformers), minimal impact on upstream and downstream equipment and building structure, and the retention of a familiar operating regime. The latter was a key factor in the success of the project, as it allowed the extensive operating expertise of the PFK staff to remain highly relevant to the upgraded furnace. This led to minimized capital investment, a rapid start-up and no significant operational challenges switching over to the new equipment incorporating Hatch furnace technology."

Jan 1, 2012

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By The Hollinger Mill Staff

MR. E. L. Longmore (l), in presenting this paper at the Annual General Meeting, suggested that it was neither desirable nor necessary to read any but the briefest portion of the paper. He wished to emphasize that the scale of the milling operations at the Hollinger not only provided several units in continuous operation to ensure that the test work was being carried on under normal conditions, but also provided a large and competent staff to supervise such an extensive experiment and to criticize intelligently the recorded results. He wished to acknowledge the enthusiastic co-operation of the group of assistants whose excellent work was responsible for the confidence with which the conclusions could be presented. The following data were given as a supplement to the published paper. Following conclusion of the test work described in the paper, the size of the balls fed to the mill was changed from 3-in. diameter to 2Yz-in. Within a short time, a gradual rise in the tonnage rate took place and, as no other condition had been changed, the increased tonnage was credited to the changed character of the ball load. At present, the average daily tonnage for the mill with low discharge is 1,507 tons, an increase of 77 tons over the 1,430 tons ground when feeding a 3-in. ball. A similar increase in tonnage should be credited to the high-discharge test, if the 2;Y2-in. ball had been used at that time. This would raise the 1,117 tons ground at that time to a new figure of 1,177 tons. From a study made to determine those factors influencing the rate of pulp flow through the low-discharge mill, it became evident that the ball screen used on the high-discharge mill must have been restricting the flow through the mill, although this was not recognized at the time. Accord-ingly, it was decided to repeat the high-discharge run. Additional length was added to the 21-in. ring grizzly originally used, and the length of the reverse spiral was increased. The end of the grizzly was left open so that, if necessary, excess pulp might flow out. A coarse mesh 3 ft. by 3 ft. flat screen was provided to catch stray balls.

Jan 1, 1937

By G. E. Agar, W. B. Kipkie, R. A. Tenbergen

"This paper describes the successful pilot plant testing of a flowsheet, developed at Inca Ltd.&apos;s J. Roy Gordon Research Laboratory (JRGRL), for improved separation of the constituent minerals in a bulk copper-nickel concentrate.The flowsheet utilized the fact that xanthate concentration on the mineral surfaces is the most important variable affecting the high lime separation and that reduction of the xanthate concentration could be affected by an oxidative conditioning stage.When the adsorbed xanthate was reduced to a suitably low level, chalcopyrite and pyrrhotite could be floated to leave a high-grade nickel concentrate as the residue. Sodium cyanide was added to the froth product 10 depress pyrrhotite and any remaining pentlandite. The temporary depression of chalcopyrite by the sodium cyanide was overcome by introducing a conditioning step following cyanide addition . The advantages of the flowsheet; improved copper-nickel separation, operation without heating of the pulp, production of both high-grade nickel concentrate (29.5% Ni, .26% Cu) and copper concentrate (<0.5% Ni, 30% Cu) were all realized.IntroductionLaboratory test work undertaken at Inco and described previously(1) has demonstrated the importance of low xanthate concentrations on the mineral surfaces in the copper-nickel separation at the Copper Cliff mill.It was determined that oxidation of the separator feed (a cleaned bulk concentrate, grading about 11% Cu and 11% Ni) to lower the xanthate concentration on the mineral surfaces prior to separation significantly improved the quality of the separation (CI 4)*, particularly when no cyanide is used, but also when cyanide is added. As well, it was found that the oxidation permitted a pentlandite-pyrrhotite separation - the oxidation step brought about a decrease in the flotation-rate of pentlandite leaving pyrrhotite and chalcopyrite largely unaffected. Consequently, it was possible to produce a highgrade pentlandite product (30% Ni, 0.3% Cu) at ~83% Ni recovery , as well as a high-grade copper concentrate (0.5% Ni, 30% Cu at -96% Cu recovery)."

Jan 1, 1985

By F. Qi, T. Frišcic, C. Mottillo

"One of the principal goals of modern industry is to minimize the environmental impact and increase the materials- and energy-efficiency of transforming raw materials into valuable products. This paper will highlight our latest laboratory-scale research in low-energy, low-solvent reactivity of metal oxides and their conversion into popular metal-organic frameworks (MOFs), zeolitic imidazolate frameworks (e.g. Basolite® Z1200 component ZIF-8), and metallodrugs (e.g. bismuth subsalicylate, active component of Pepto-Bismol®). Mechanochemical ion- and liquid-assisted grinding (ILAG) and ""accelerated aging"" techniques will be presented, along with novel low-energy and solvent-free approaches, inspired by geological weathering processes, for converting metal oxides into metal-organic materials. INTRODUCTIONThe development of environmentally-friendly processes, which would in the same time be more materials- and energy-efficient than the existing ones, is one of the central concerns of modern chemical research. In that sense, the focus of the chemist has been mainly on the preparation of carbon-based organic molecules and adaptation of traditional organic synthesis to the recently delineated ideals of Green Chemistry. However, there is a growing realization within the chemistry community that significant energy, materials, and ecology-related benefits can be achieved and, indeed, targeted in the transformations of materials that are typically associated with inorganic chemistry and minerals processing. The principal aim of this highlight contribution is to illustrate how, through the use of approaches associated with solventfree chemistry and mechanochemistry (James et al., 2012), one can develop a clean and efficient system of chemical and materials transformations involving oxide precursors that normally belong to the realm of inorganic chemistry and mineral processing. In particular, this contribution will provide an overview of the recently developed mechanochemical and solvent-free reactivity of metal oxides towards small organic molecules. These mechanochemical reactions, including the methods of liquid-assisted grinding (LAG, Frišcic & Jones, 2009) and ion- and liquid-assisted grinding (ILAG, Frišcic, 2010), have so far provided a radically different means to construct advanced metal-organic materials (e.g. porous metal-organic frameworks, [MOFs] or metallodrugs) by rehabilitating metal oxides as precursors, eliminating the use of bulk organic solvents, and avoiding the use of high temperatures."

Jan 1, 2012

By R. S. Bigelow

Part 1.- Metal Mines Early experiments with mechanical loaders in metal mines were confined largely to machines of the shovelling type and generally air-operated. Although the first application of the scraper to metal mines dates back to 1910, it was not until about twelve years ago that it came to be used extensively. Generally, the scraper gives better results in metal mines than in coal mines, as degradation due to soft bottom and breakage are not factors, but it has a wide range of application and is successfully used in the mining of salt, potash, gypsum, zinc, copper, and a variety of ores, from soft material to hard chunky ore which settles compactly. Today, the scraper has replaced to a large extent the shovelling type of machine in metal mines. Scrapers have offered an inexpensive solution for the mucking problem and are now employed in most mining districts throughout the world. They are operated by labourers of all colours and degrees of skill. Each installation, however, requires individual study on the part of the mine mechanical department to determine the type of scraper, horsepower of hoist, and most economical speed of rope, as well as method of rope rigging. Unfortunately, the scraper has no power to select pay ore from waste and its suitability for use under circumstances which might require sorting of the ore can only be decided by a weighing of the economic factors involved

Jan 1, 1931

By J. E. Ryan

General Description Due to the extreme cold weather experienced in Flin Flon during the winter months, thought and precaution were necessary in the design of the plant buildings. The machine shop, carpenter shop, drill shop, and coal plant buildings are similar in the building materials used in their construction. They are sided with two-inch shiplap, insulated with celotex and asbestos paper, and covered with corrugated iron on all side-walls. Roofing consists of 2 by 4 lumber on edge, laminated, and further covered by celotex and three-ply roofing. These buildings are heated by means of unit heaters. The heaters are primarily steam-heated radiators, through which the air of the buildings is circulated by electrically-driven fans. Our machine shop is located to the east of, but central to, the main operating buildings of the mine and plant, and is so connected by a net work of tracks as to be able to serve all portions of the entire plant conveniently. The building is divided into two bays, the main bay 53 ft. by 340 ft., and the east bay 24 ft. by 340 ft. The shop office and drafting room, a two-story annex 24 ft. by 30 ft., is located on the west side of the shop. The arrangement within the shop is such as to house conveniently the several departments, namely, heavy machine tool section, repair floor section, boiler shop heavy tool and floor section, blacksmith heavy tool and forge section, tool room, electric welding rooms, stock room, tin and copper shop, and electrical parts and armature winding and repair shop (see Figure 1). All the heavy tools, the repair floor section, and railway tracks are so located in the large open bay as to be fully serviced by an electrically operated 15-ton bridge crane, with a span of 50 feet and a travel the full length of the shop. A standard-gauge railway track, branched off the main line, penetrates the full depth of the building. This track lies along the extreme east side of the main bay, allowing easy entrance and movement of rolling stock and heavy machinery, loaded on standard flat-cars, to the repair floors in the main bay. Eight jib cranes, affixed to building columns, further facilitate the heavy repair work throughout the various shop divisions. Our light and heavy machine tools are standard equipment, not unlike tools used in mine, mill, and railway shops.

Jan 1, 1935

By Håkan Schunnesson, Kirsten Holme

"When mining high grade, narrow ore bodies, the mining method often implies a very detailed knowledge of the ore contacts to avoid unacceptable ore loss and waste rock dilution. During the past decade, the use of microprocessor based drill monitoring equipment has become an accepted technique, even for percussive drilling. On the basis of the recorded drill performance, such as penetration rate, torque pressure, thrust etc., a fast evaluation of the lithological sequence of the ore zone can be made. In order to evaluate the potential of percussive drill monitoring to pro-vide detailed information of the geometry of the ore body, the technique was tested in the Viscaria copper mine in Sweden during 1996.To provide understandable information to the mine geologist, great emphasis was placed on the separation between the drilling response generated by variations in rock conditions from variations caused by the operator and the drill system. Due to the complicated geology in Viscaria, the drilling response presented to the geologists was separated in two independent signals, one representing the hardness of the rock and one representing the in homogeneity(fracturing) of the rock. With those signals a good separation between different rock types in the ore horizon was achieved.The experience from the Viscaria copper mine is that drill monitoring not only can be used to locate contacts between rock types, but also to characterize rock conditions and, often, also to specify the exact rock type present. Because it is possible to get the drill monitoring information very quickly it is a valuable complement to diamond drilling for increasing the specific knowledge of the geology and the ore body."

Jan 1, 1997

By H. Dean

"Mine hoisting machinery, of which wire rope is an essential part, is developing, in Canada as well as in other parts of the North American continent, into highly sophisticated equipment. Heavier payloads are now required to be raised from steadily increasing depths at higher rates of speed and production. These hoisting conditions have, of necessity, brought about a major change in the production of steel roping wires and the wire ropes manufactured from them.Operators and designers of hoisting equipment are requesting a very much more efficient ratio of strength to weight in hoisting ropes, so that heavier loads may be raised from greater depths by ropes which will provide a predeterminable life span on which the operator may depend.The cost of wire rope to the operator is very low indeed, usually less than $0.01 per ton of payload, but the cost of unexpected shutdown periods, due to rope maintenance or change, can be extremely high -particularly in operations where a continuously high rate of production is an absolute necessity. Mine hoist ropes with a higher strength to weight ratio are now being made and used in some areas of Canadian mining, and a general understanding of the performance we may expect from them is required."

Jan 1, 1968

By H. Salomon-de-Friedberg

The amount of pyrite in copper concentrates fed to the CESL Process can vary appreciably. The fraction of pyrite that oxidizes influences both capital and operating costs and is therefore an important variable. The present paper explores operating conditions that influence the extent of pyrite oxidation and the probable overall reaction chemistry under CESL conditions.

Jan 1, 2014

By L. L. Bolton

The Department of Mines as at present constituted has evolved from the organization which came into existence following the passage of the Geology and Mines Act by the Dominion Parliament in 1907. At the outset, it may be said that it is not a function of the Department of Mines, nor of any of its branches, to administer the mining rights vested in the Crown. The title to Crown lands in the provinces of Nova Scotia, Prince Edward Island, New Brunswick, Quebec, Ontario, and British Columbia ( with the exception of certain specified areas, such as Indian Reserves, Ordnance Lands, the Railway Belt of British Columbia, and the Peace River Black) is vested in the respective provincial governments ; the title to Crown Lands in the provinces of Manitoba, Saskatchewan, and Alberta, the Yukon and Northwest Territories, and in the Canadian Arctic, is vested in the Dominion Government, and matters pertaining thereto are (with a few exceptions) administered by the Department of the Interior, Ottawa. Nor are statistics of mineral production at present collected and published by the Department of Mines. This function did belong to the Geological Survey from 1886 to 1906, and to the Mines Branch from 1907 to 1920; but commencing with 192l this duty was transferred to the Dominion Bureau of Statistics, consequent upon the decision of Government to place the collection of all statistics under the direction of one officer.

Jan 1, 1929

By James A. Robertson

"This paper is the result of a continuing investigation begun in 1953 by government geologists and mining companies. Previous work is reviewed and the development of several stratigraphic nomenclatures and correlation schemes is traced, culminating with the interim report of the Federal-Provincial Committee on Huronian Stratigraphy formed in 1966.The stratigraphy, structure and correlation of the Huronian rocks of the Blind River area and the region between Sault Ste. Marie and Sudbury are reviewed. The area is underlain by three Precambrian units: (1) the Archean greenstones and granites, (2) the Huronian sedimentary and volcanic rocks and (3) the post-Huronian intrusive rocks. The Huronian rocks, largely quartzite and conglomerate with greywackes, argillites and carbonates, were laid down in shallow water transgressing over the eroded Archean basement. Thickness and facies changes indicate a northwesterly source, northerly overlap and deposition controlled by basement topography. Polymictic conglomerates, occurring at least at three horizons, represent tillites and are associated with varvites with dropped clasts. These are best developed in the Gowganda formation, which varies from a continental glacial environment in the north to a marine glacial environment in the southeast.There were at least three phases of post-Huronian igneous activity, probably related to several periods or phases of late Precambrian deformation and metamorphism: (1) sills of Nipissing diabase and rather younger diabase dikes; (2) the Cutler Granite and Croker Island Complex; and (3) dikes of Keweenawan olivine diabase.Copper mineralization is associated with the Nipissing diabase. The uranium ores are found in pyritic quartz-pebble conglomerate near the Huronian Archean unconformity, particularly in ancient valleys; they are considered to be placer deposits modified by later events. Uranium production from the Blind River camp to the end of 1966 was 128,160,096 pounds U308 valued at $1,203,840,848 derived from 56,077,179 tons of ore grading 0.11 per cent U308.Within the Blind River and adjacent areas, future discoveries will probably be the result of costly systematic deep-drilling programs accompanied by detailed geologic studies of the type carried out by oil companies and probably computer-oriented."

Jan 1, 1969

By A. Pearson, Auld. F. A., S. O. Colbeck

"To minimise mine shaft maintenance over the long-term, some potash mine shaft sinking projects have required the provision of a continuous fully welded waterproof steel liner over a substantial depth to achieve zero water ingress. This brings many challenges, including the implementation of a bottom-up construction sequence incorporating extensive waterproof welding and how to ensure the integrity of the welded liner when subject to substantial temperature fluctuations that are likely to occur with a composite steel-concrete liner placed within an artificially frozen shaft excavation. This paper highlights the key challenges and discusses multiple mitigation measures including vertical shaft movement joints and a combined structural-thermal analysis approach. INTRODUCTION Whilst the application of combined steel and concrete shaft liners using a fully welded steel liner is not new and has been used in several previous projects, most notably at Lanigan (Storck, 1968 & Roesner, 1980), recently the need to provide a continuously welded steel waterproof liner for over 800 m length of shaft for a potash mine has been considered. The need for a fully continuous welded steel liner arises from the perceived benefits of providing a fully dry shaft environment to; increase the life expectancy of the shaft; reduce routine maintenance particularly combatting salt accretion and minimising wash down practices; and improve long-term ground stability by preventing salt dissolution. Whereas previous projects have employed discontinuous sections of steel liner, when a fully continuous liner is employed longitudinal shaft strains from thermal changes result in significant deformations that must be either explicitly accommodated or resisted. Note, these thermal vertical expansion forces are more than capable of lifting the shaft collar and head frame structures should they be fixed in place. Typically, shafts are designed to resist vertical forces (collar loads and self-weight) by creating mechanical interlock with the adjacent ground. In competent rock this occurs incrementally with the construction of the shaft liner, and occasional hitch/crib structures are constructed as intermediate foundations to guarantee the transfer of vertical forces at distinct horizons. Usually this means cribs are constructed at first rock head, above the station level, and at the sump, although sometimes additional cribs are formed when entering and exiting weak strata or when a change in shaft liner construction is required."

Jan 1, 2019

By John Kostuik

"This paper discusses the outlook for uranium resources, and comments briefly on the measures needed to meet market objectives. Areas of recent exploration interest are also discussed.THE PREVIOUS SPEAKER has capably described the truly phenomenal growth in demand for energy from all sources. The basic factors -population growth and industrial development -which will create energy demand are so fundamental to national economies that the ascending energy demand curve will be little affected by short-term factors.Because of the economic and practical advantages of nuclear power and the degree of present acceptance by electric utilities, there is no doubt that uranium will be a principal source of primary energy in industrial countries -and this will happen within a decade. Indeed, during this period it will be the fastest growing source of energy, capturing, for example, more than half of the electric utilities' expansion in the United States by 1980. The ready availability of energy sources from domestic and foreign resources is so essential to industrial nations that the long-range outlook for their adequacy is of prime importance. There has been international concern about the availability of uranium resources at reasonable cost to adequately support and foster the development of the nuclear power industry. Canada, fortunate in having established reserves and a potential in excess of any forseeable domestic demand, can confidently look forward to being a principal supplier to the industry."

Jan 1, 1969

By Walter Herd

For the past eight years, No. 2 mine of the Cumberland Railway & Coal Co., Springhill-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Depart~ of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. °This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room-and-pillar method was employed, and in January of that year (there being a cessation of work from March to August due to labour troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine, was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In ?the interval, development work for longwall retreating below the 5,900-foot level was vigorously pushed.

Jan 1, 1929

By L. Lafrenière

A trend in mining exploration is to increase the number of geophysical parameters collected and interpreted for geological features in a given area. Airborne technology now allows us to simultaneously combine electromagnetic, gravity, aeromagnetic and radiometric surveys. We report the results of a multiparameter survey conducted in the area of Kamiskotia, Ontario. This area is located near and on the West side of the multi-metalliferous Kidd Creek deposit. Various metallic occurrences are reported in the studied area. Integrating multiple parameters in the interpretation produces a more detailed pseudogeological map than what has already been published. 3D interpretation has been undertaken using some of these parameters and suggests that future work is required in 3D earth model solutions in order to fully use all parameters.

Aug 1, 2013