Search Documents

By A. Lewis, J. Zachwieja, M. Widell, P. Zhou, W. W. Geissler, M. Svensson, A. Movahedi, H. Nordberg

Flotation collectors for sulfide minerals has been traditionally based on xanthate, thiophosphate, thiophosphinate and thiocarbamate, all derived from sulfur chemistry. Tecflote™ is a new family of patented collectors based on nitrile chemistry which can supplement or replace thiol collectors, depending on the ore types. A steep grade-recovery curve typical of Tecflote™ collectors was observed when using Tecflote™ as the main collector for the rougher and cleaner steps allowing a better recovery compared to current thiol collectors while maintaining the desired grade. Additional recovery increase has also been observed by the addition of scavenger steps using Tecflote™ collector in combination with current thiol-based collector. The selectivity seen in the lab is transferred to full scale trial and is clearly seen in the rough flotation where the increase in the rough concentrate grade of 5% after pumping Tecflote S11 directly into the tank cell. The mechanisms for Tecflote’s selectivity towards sulfides are currently under investigation and will be discussed. Results of TOF-SIMS analysis will be presented, demonstrating the collector’s selective affinity to different mineral surfaces in flotation. INTRODUCTION The history of collectors used today started in 1882 when Zeise first made xanthates. It was first used in flotation in 1925 – Cornelius Keller’s first patent (Fuerstenau, Jameson, Yoon, 2007). Between 1928 and 1930 American Cyanamid filed 7 patents for dithiophosphate, including flotation and chemical synthesis of the reagent, the first of which was filed by Christmann in 1928 (Christmann, 1933). Synthesize of thionocarbamates for mineral flotation was filed in 1954, by Dow Chemical Company (Harris, 1954). Now that the head grades have been declining over the last decades the need to find more selective collectors to extract difficult and complex ores has pushed the industry to look at different chemistries. Thiol collectors standard to the industry rely on the sulfur in the collector molecule to bond to the mineral surface. The electronic property of this group is modified by the adjacent chemical groups, such as additional S, P or N have the effect of changing the selectivity of the collector (Wills & Finch, 2016). In the case of xanthate the length of the hydrophobic group also has an effect on the selectivity with some minerals such that the ethyl xanthate is more selective against pyrite and pyrrhotite than the long chain xanthates (Wills & Finch, 2016).

Jan 1, 2019

By Paul J. Sylvester, Yeonuk Choi, Mike Nelson, Louis J. Cabri, Mike Tubrett

"The development and characterization of sulphide standards containing as many as seven precious metals has increased the efficiency and comprehensiveness of micro-analyses for deportment studies using laser ablation microprobe inductively coupled plasma mass spectrometry (LAM-ICPMS). Because trace precious metals occurring in solid solution or as sub-micron inclusions in sulphides, arsenides, and sulpharsenides are often heterogeneously distributed, a significantly large number of analyses are required. Using well-prepared samples it is possible for up to 120 analyses per day, far more than by other comparable methods. Examples will be discussed from projects focused on the deportment of Au and the platinum group elements (PGE).INTRODUCTIONBecause gold and the platinum-group elements (PGE) occur as both discrete minerals and in trace quantities in a variety of minerals (mostly sulphide, arsenide, and sulpharsenide minerals), specialized trace analytical methods were developed and applied to determine the deportment of precious metals in ore deposits, requiring sensitivities ranging originally from about hundreds to presently tens of ppb for individual precious metal or less.In mineralogical studies, micro-analytical techniques such as the electron microprobe were first applied to obtain analyses for major elements in about 1959-60, but as the instrumentation improved early attempts for PGE in potential carrier minerals indicated that reasonable levels of detection (LOD) were of the order of 300-400 ppm, depending on analytical conditions, X-ray spectral lines, and mineral matrix (e.g., Cabri and Laflamme, 1976). Eventually, the lowest detection levels by electron probe micro-analyses (EPMA) obtained for some PGE were of the order of 10s of ppm using high accelerating voltage and current for extended measuring time on peak and background (Gervilla, Cabri, Kojonen, Oberthür, Weiser, Johanson, Sie, Campbell, Teesdale and Laflamme, 2004)."

Jan 1, 2010

By D. B. Felsher

"Lakeshore Gold’s Bell Creek Mill is located in Timmins, Ontario. The mill has been in operation since 2009 and has undergone several small expansions since then. In 2012 - 2013 the first major mill expansion was commissioned raising the mill capacity from 2,000tpd to 3,150tpd. This was done through the installation of a new ROM ore truck dumping facility, jaw crusher, ore storage dome, SAG mill, leach tank, CIL tank, and electrowinning cell. This paper will cover the equipment installed to raise the tonnage as well as the commissioning of the new equipment including problems encountered and how these problems were solved.IntroductionLake Shore Gold acquired the Bell Creek Mill, along with the Bell Creek Mine, from the Porcupine Gold Mines Joint Venture, a joint venture between Goldcorp Canada Ltd. and Kinross Gold Corporation, in December 2007.The Bell Creek mill, which processed ore from the Bell Creek Mine has consistently achieved recoveries of over 95%, is a conventional gold mill circuit, involving crushing and two stage ball mill grinding, gravity and leaching, followed by Carbon-In-Pulp (CIP) process for gold recovery. The facility had been placed on care and maintenance in 2002. At the beginning of 2009, the mill had been refurbished with an initial capacity of 800 tonnes per day and was subsequently refurbished to a capacity of 1,500 tonnes per day near the end of the third quarter of that year. The Mill was then expanded in 2010 to a capacity of 2,000 tonnes per day.In late 2011, the Company commenced a 50% expansion of its milling facility, from a processing capacity of 2,000 tonnes per day to 3,150 tonnes per day. Phase 1 of the expansion, which mainly involved enhancements to the solution circuit (“back end”) and increased the mill’s capacity to 2,500 tonnes per day, was completed at the end of 2012. Commissioning of Phase 2 of the expansion, to a capacity of 3,150 tonnes per day, commenced at the end of July 2013."

Jan 1, 2015

By Joe Zhou

"Mineralogical characterization and metallurgical extraction of silver is challenging due to its complex mineralogy and chemistry. Over 200 Ag-bearing minerals have been identified and a silver-rich ore body would typically contain 5 to 10 different silver minerals. Silver can occur not only as discrete microscopic (visible) silver minerals but also as submicroscopic (invisible) silver in other minerals. During processing, silver may form passivation compounds such as silver hydroxide, silver sulphide, jarosite-like silver sulphate, silver halide or silver cyanide precipitate, all of which may negatively impact on silver extraction. Knowing the deportment of silver in the ore and its metallurgical products is important in flowsheet design and plant optimization. This paper begins with the classification of silver ores and minerals and a review of processing techniques, and focuses on the major mineralogical factors to explain why and how these factors affect silver extraction. Case studies are provided to demonstrate the application of silver process mineralogy in flowsheet design and plant optimization.INTRODUCTIONSilver was known to and utilized by mankind since ancient time. Actually, it was one of the earliest metals discovered and utilized by mankind after gold and copper.Silver is the whitest metallic element. It is rare, strong, corrosion resistant, and unaffected by moisture, vegetable acids, or alkalis. Silver is also resonant, moldable, malleable, and possesses the highest thermal and electric conductivity of any substance. The chemical symbol for silver is Ag, from the Latin argentum, which means white and shining. Although silver does not react with many chemicals, it does react with sulfur, which is always present in air at trace amounts. The reaction causes silver to tarnish, and consequently it must be polished periodically to retain its luster.Silver possesses many special physical characteristics and qualities that make it useful to a variety of industries. The photography industry is the biggest user of silver compounds. Silver forms the most light-sensitive halide salts, which are essential to developing highquality photographic prints. Silver also has the highest electrical conductivity per unit volume of any metal, including copper, so it is used extensively in electronics."

Jan 1, 2010

By A. R. Harrington

BEFORE discussing some of the technical aspects of the steam generating plants of Nova Scotia Light and Power Company, Limited, it might be of interest to go back through history and see the development of steam generation in this public utility. Back around 1902 Nova Scotia Light and Power Company, Limited, had three slide-valve engines in-stalled at its Water Street, Halifax, generating station for a total capacity of 1,800 kilowatts. The plant remained at about this size until 1910 and in 1911 a 2,000 kilowatt steam turbine was installed to raise the total capacity of the plant to 3,800 kilowatts. In 1916, a 3,000 kilowatt turbine was installed and one of the slide-valve engines was removed to make a total plant capacity of 6,200 kilowatts. The total demand in the Company's service 8rea was at that time 4,000 kilo-watts.

Jan 1, 1958

By F. D. Aaring

"IntroductionTHE PINCHER CREEK gas condensate field, in Township 3, Range 28, and Townships 3 and 4, Range 29, West of the Fourth Meridian, was discovered in 1947 by the Canadian Gulf Oil Company with the completion of Pincher Creek No. 1 well in the Madison lime-stone of Mississippian age.This discovery was the result of a great deal of detailed seismic work in the area and is a credit to the geophysical personnel of the Company. The depth of the reservoir varies from 7,400 feet to 8,200 feet subsea, with the established water level at -8,200 feet. The predicted depth was but a scant 100 feet from that found in the discovery well, at 11, 705 feet. Since the discovery of the reservoir, three additional wells have penetrated the Madison limestone and have further verified the original •seismic interpretation of the limits of this reservoir.To date, •only a very small amount of gas has been produced from this field. Consequently, the reservoir studies that have been made so far are predominantly based on investigations of the phase behaviour of the fluid and physical characteristics of the reservoir rock. In view of the above limitations, it has been necessary to set up and perform model reservoir studies with the fluids and to recover as much core from the productive Madison limestone as possible in order that it might be analysed by conventional laboratory technique and be subjected to detailed microscopic geological examination."

Jan 1, 1952

By Mark Ferra

Flotation is used in mining to produce concentrates of copper, gold and several other valuable ores. In 2017, a copper mine near Globe, Arizona improved their rougher cells productivity using technically advanced electro-hydraulic actuators in the flotation process by enabling excellent tank pulp level process stability. The new actuators controlled the dart valve position to allow pulp to leave the cell. Tank cell pulp level can change due to feed and discharge fluctuations from neighboring tanks. When traditional pneumatic actuators are used, they have sluggish response times and overshoot due to the inherent physical property of air being compressible. Electro-hydraulic actuators have the benefit of hydraulic stiffness to deliver accurate and repeatable (0.1%) dart valve positioning. The froth layer has more opportunity time to maximize mass transfer into the launderer. The results are an increase in copper recovery by 2-4%. INTRODUCTION In 2013 there was an international flotation technical conference well attended by respected flotation specialists for both mining companies and academia. During the technical session a leading metallurgist was discussing pulp level measurement and said that when he was on the cell deck he stated, pneumatic actuators air cylinders stroking up and down. The presenter then claimed with confidence that "I listened to actuator move so the pulp level in the tank was being controlled!" No one questioned his assumption and I can assert that the audience was quite technical and not shy in their critiques of speakers. The flotation community simply believed that the existing pneumatic technology was enough with no alternative. Having a stable flotation cell pulp level is critical to effective copper recovery. Controlling pulp levels in flotation cells is a complex task that includes modulating dart valves in each cell. The use of REXA Electraulic actuators will decrease the process dead time and maintain froth height in a controlled manner, especially from pulp slurry volume fluctuations from neighboring cells. By reducing flotation cell pulp level tank height variation, a copper mine in Arizona has realized a 2-4% recovery improvement by increasing the froth transfer to the launderers in the rougher cell circuits compared to pneumatic actuators. This paper examines the benefits of using an electro-hydraulic actuator to ensure proper pulp level control and reduce the process operational cost. It will focus on actuator positioning the dart valves to maintain pulp level setpoint at a copper mine in Arizona.

Jan 1, 2019

By W. H. Patterson

The history and experience of early companies in the Islands is illustrated by the typical transactions of Trans-Western from 1959 to date. Trans-Western had entered into farmout agreements with companies strong enough to carry out at least the required minimum exploratory work and then such development as might be warranted. The farmee companies were required to make deposits to guarantee work performance during the first period of validity, i.e. the first 3 years of the 12-year life of the permits, and at the rate of 5 cents per acre. At that time, a good deal of geology was available, as a result of extensive exploration that had been carried on by the Geological Survey of Canada and other geological enterprises, with field parties travelling over and camping on all of those Islands. Trans-Western's farmees then selected, from Trans-Western's priority on 13.5 million acres, what they believed were the lands most prospective of producing large oil and gas discoveries, and, having the right to trim off acreage which they considered less prospective, thereby reducing the acreage of Trans-Western and its farmees to in excess of 5.5 million acres. The farmees then commenced a 3-year program carrying out geological exploration to the required minimum of 5 cents per acre, and with some permanent and many mobile camps.

Jan 1, 1969

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is con-?ned by tectonic shear zones between marble and metapelites, extending laterally into the marble astabular, pod or lenticular oreshoots (up to 50 m x 20 m x 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical pro?les across mineralized zones con?rm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the in-situ supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly in?uenced by seasonal ?uctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent ?ooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2~10-3.8 to 10-1.4) and oxygenated (fO2~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sul?des and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+was transportedinto karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Abstract-Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is confined by tectonic shear zones between marble and metapelites, extending laterally into the marble as tabular, pod or lenticular oreshoots (up to 50 m ?? 20 m ?? 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical profiles across mineralized zones confirm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the insitu supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly influenced by seasonal fluctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent flooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2 ~10-3.8 to 10-1.4) and oxygenated (fO2 ~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sulfides and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+ was transported into karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2 in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2 increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By R. K. Netolitzky

The Weedy Lake, Tower Lake, and Wedge Lake gold deposits illustrate contrasting styles and different ages of mineralization within the same district. The discovery of these deposits was the result of systematic exploration of gold occurrences noted during research of assessment files. The Weedy Lake and Tower Lake depo its reflect a late-stage gold mineralizing event. The e deposits developed along the same major structural break, and also display simi lar mineralogy and alteration patterns. Mineralization is developed in all the lithologies present. The Wedge Lake property, while having occurrences similar to the Weedy and Tower deposits. has the more important Twin Zone which best fits a volcanogenic exhalative model. The Twin Zone has a complex structural history without a recognizable alteration halo. The setting may be proximal to a hydrothermal vent. Mineralization is hosted within a mixed ulphide/oxide/silicate facies iron formation breccia. and the gold is intimately associated with arsenopyrite. The origin and age of the brecciation is key to understanding the mineralizing event. Traditional prospecting procedures in conjunction with conventional B-horizon soil geochemistry were instrumental in the Twin Zone and Weedy lake disco,•eries. Tower Lake was a prospecting discovery partially defined by previous drill programs. This deposit was also identified by B-horizon oil sampling.

Jan 1, 1986

By Marco A. Vera

"This paper investigates the froth function in flotation and the associated upgrading process. Flotation literature has revealed that one of the main functions of the froth phase is the cleaning of bubble-particle aggregates by rejection of entrained material. The cleaning and transport processes across the froth phase exert straining forces on these aggregates on their way up to the froth surface. These forces will impact on the recovery of bubble-particle aggregates.The grade at the top of the froth (TOF) is a parameter related to the quality of particles collected by bubbles in the pulp zone (true flotation). It has recently been demonstrated that TOF corresponds to the maximum practically attainable grade described by the recovery-grade (or enrichment ratio) curve. TOF lumps all the processes experienced by the bubble-particle aggregates before reaching the launder concentrate. This paper describes a methodology for quantifying flotation performance by means of the top of the froth sample - a touch of froth.INTRODUCTIONFroth flotation may be the most important mineral processing technique, but its theory is complex and is not completely understood even though many aspects have been studied and reviewed (Teague, 1998; Wills, 1992).Two distinct particulate systems prevail in the flotation process: a pulp phase and a froth phase (Figure 1). The pulp zone had been studied extensively; however, it is only recently that techniques to measure the froth zone performance have been developed (Contini et al., 1988; Falutsu and Dobby, 1992; Feteris et al., 1987; Seaman, 2002; Vera et al., 1999b).Flotation involves a number of mass transfer processes, occurring in the pulp phase and the froth phase. The formation of the froth and its subsequent removal are considered to be two important steps of the process. Phenomena that occur in the froth phase are known to affect flotation performance significantly (Cutting et al., 1981).Because the froth has a high free surface energy (as a result of the extensive interfacial surface between liquid and air), it appears thermodynamically unstable. The foaming is a dynamic balance, as new bubbles are added continuously from the pulp, while others disappear from the top. Under steady-state conditions, the volumes of added and subtracted air are equal (Booth, 1953)."

Jan 1, 2003

AT the Annual General Meeting held in Winnipeg last March, the whole of one of the technical sessions was devoted to a special Symposium on Geological Investigations in Canada, introduced by a paper entitled The Geological Survey (lî which had been specially prepared by Dr. G. A. Young, Chief Geologist of the Survey, and had been published in the February BULLETIN, prior to the meeting. Geologists from each of the provinces contributed to the Symposium, including directing officials of the geological divisions of provincial Departments of Mines, representative geologists from the Universities, and company and consulting geologists. Space, unfortunately, does not permit publication of a complete record of the proceedings,_ or even inclusion of all contributions to the discussion. The following summary, however, gives what is believed to be a fair cross-section of the opinions expressed by representatives from each Province. The Symposium resolved itself largely into a discussion as to how the Geological Survey and the several provincial bureaus or divisions of geology could co-operate most effectively in the important task of carrying out geo-logical investigations, with avoidance of duplication of work and waste of effort, and, so far as broad principles are concerned, there was remarkably close agreement among those participating in the Symposium as to how the various types of investigation should be allocated as between the Federal and Provincial organizations. Briefly, the concensus was that the Geological Survey can render the most effective assistance by conducting reconnaissance investigations, with mapping at 4 miles to one inch, leaving to the provincial organizations the more detailed, and hence more local, studies and mapping at larger scales. There was general agreement that the preparation of base maps, essential to systematic geological investigation, is a service devolving upon the Federal Government.

Jan 1, 1940

By T. Binnert Haites

INTRODUCTION NUMEROUS examples of troubled zones, interfering with the normal development of coal seams, have been cited in the literature. From a geological point of view they can be subdivided into structural and sedimentary troubles. Of the latter type, wash-outs are usually the most bothersome. Some years ago, A. A. Thiadens and the author arrived at the conclusion that they represent fossil river-beds. A method of predicting the course of these rivers was developed, which has been successfully applied in the Netherlands coal measures, and more recently by P. Stassen in some of the Belgian coalfields and by the author in the Sydney coalfield. The Sydney coalfield has long .drawn the attention of geologists, and three main periods of systematic geological research may be distinguished. The first period, 1872-1900, is covered by the studies of Ch. Robb and H. Fletcher (32, 10-13) (1). Their detailed sections of the cliffs have lost nothing in value, and are frequently consulted today.

Jan 1, 1951

By J Petrolito

"To improve the economic and environmental performance of underground mining operations, it is common practice to return the metallurgical waste material underground as backfill. This is called hydraulic backfill and is used to fill the mined-out areas not exposed to further mining. To provide mechanical support for underground mining a cemented backfill is normally used. Since its introduction, cemented backfill has allowed mining companies to increase their ore extraction and improve working and environmental conditions. However, cemented backfill represents up to 50% to 85% of the mine’s operating cost compared with 5% to 10% for hydraulic backfill.These economic pressures have led mining companies to carry out research into the partial or total replacement of cement using a variety of alternative materials. The materials are generally site-specific materials, readily available, and cost-effective relative to cement. Such investigations have led to reduced cost of many backfill mixes while maintaining, and in some cases improving, the physical properties of cemented backfill. However, in most cases, cement still remains an integral part of any binder combination. This can be attributed to the alternative binders investigated being either non-binding materials or capable of generating only low-strength backfills, except when used in conjunction with cement.This paper provides a historical review of backfilling binder materials and their characteristics. In particular, it reviews the many alternative materials that have been proposed to either partially or fully replace Portland cement as the main binder."

Jan 1, 2005

By R. H. Walton

"In recent years the recovery of copper from low grade oxide ores has received widespread attention. The cost of treating such ores using conventional technology, such as milling and flotation, is frequently prohibitively high and copper recovery is generally low. The introduction of heap leaching, solvent extraction (SX) and electrowinning (EW) has resulted in high recoveries, good copper cathode quality and low production costs. This technology has now been successfully applied on a worldwide basis.This paper reviews the various process and design options and gives approximate capital and operating costs for a 1.0% copper ore.INTRODUCTIONAs a result of the low copper prices that prevailed for much of the last two decades, aggressive attempts were made by the industry to cut operating costs. Under such circumstances heap leaching, solvent extraction and electrowinning, to recover low cost copper from oxide ores, has received particular attention and ultimately widespread acceptance.Low grade copper ore (typically containing less than 1.0% Cu), which could not be economically treated by other methods, is placed on heaps and leached with dilute solutions of sulphuric acid. The copper rich, pregnant solution, drains from the heap into a collecting pond and is pumped to a solvent extraction plant where it is purified and upgraded. The resulting solution, termed the pregnant electrolyte, passes to the electrowinning section where the copper is recovered as high grade cathodes and sulphuric acid is regenerated, (Figure 1).This paper specifically describes the processing of copper oxides. Other copper minerals such as chalcocite and chrysocolla are also leached by dilute solutions of sulphuric acid. In practice the oxide minerals are frequently associated to varying degrees with less easily leached sulphides, such as chalcopyrite. In some cases, once the oxidized capping of the ore body is removed, the oxides are totally replaced by more refractory sulphides. Under these circumstances the leaching recovery is significantly reduced. However the principles described here for solvent extraction and electrowinning are also applicable to solutions received from heaps containing sulphide minerals, which are leached more slowly and involve bacterially induced reactions."

Jan 1, 1990

By D. A. Trotter, G. J. Goddard

"This paper describes a method of deciding on various design parameters for a sublevel caving layout. Layout design curves are obtained from the output of a computer optimization program. The program uses mathematical relationships derived from the theory of gravity flow of material to optimize the large number of interdependent design variables which are involved.IntroductionIn the design of an efficient sublevel caving mining system, a large number of interrelated variables need to be considered. Although many papers discuss individual variables, very little exists in the literature to show how these variables interact to achieve optimum results. This can lead to trial and error in sublevel caving design, which can prove costly, particularly because sublevel caving is a mining method which requires integration with sublevels above and below. With no pillars being left, experimental stopes cannot be isolated for study. Unfortunately, the complexity of layout design and the costs associated with trial and error have caused many planning engineers to choose more tried and tested mining methods.Sublevel caving works best to extract low-value ore surrounded by incompetent rock. All phases of the mining method can be highly mechanized, allowing low operating costs and high production rates. Good safety records are achieved, as workers are always in 'good' ground and the method is regular, making it comparable to an industrial process."

Jan 1, 1981

By Anton Gronningsater

AS we know, Sir Henry Bessemer introduced Bessemer converting in the steel industry about 1855. It was not until twenty years later that the principles were adopted by non-ferrous metallurgists. In 1880, Manés first produced blister copper from matte in a converter, a very important forward step in copper metallurgy. For thirty years, up to about 1910, bessemerizing of copper matte was carried out in the acid-lined converter. It is not necessary here to enumerate all the shortcomings of that operation, one of which was that it strictly limited the grade of matte that could be treated; a 35 per cent matte was low in those days. From the early days of copper converting, many and repeated attempts were made to use a basic converter lining, and the older metallurgists will remember the numerous reports and discussions in connection with such experiments. These make interesting reading. I quote from a book published in 1900: ?'The siliceous lining is as much a part of the process of copper converting as magnesia lining is in the basic bessemer treatment of phosphoric iron, and it is suicidal to attempt any other kind of lining, either water-jacketed or basic.' "Even if the silica could be introduced in this way (through the tuyeres), it would still produce another trouble in the converter. The small particles of silica, being cold, would combine very imperfectly with the iron oxide and produce granulated and pasty slags, which could not be skimmed or poured out of the vessel".

Jan 1, 1942

By H. J. McQueen

ORDER OF PRESENTATION ?INTRODUCTION TO THE VICTORIA BRIDGE ?REASONS FOR A BRIDGE AT MONTREAL ?RAILROAD BRIDGE REQUIREMENTS ?IRON PRODUCTION CANADA / WORLD AL ?METALLURGICAL INDUSTRY CANADA ?FAIRBAIRN, STEPHENSON SHIP PLATE-RIB BOX GIRDER ?VICTORIA BRIDGE (PREFABRICATED BRITAIN) ?IRON ORE SITUATION THE VICTORIA BRIDGE 1859, TUBULAR -WROUGHT IRON* 1898, TRUSS ?STEEL* (*HOT RIVETED) 1957, SPUR, LIFT SPANS ??DUCTILE WROUGHT IRON WITHSTANDS FATIGUE ?TO KEEP THE TRAINS ON TIME & ON TRACK? ??IMMOVABLE SHARP PIERS SPLIT ?THE IRRESISTIBLE ICE, STOPPED CITY FLOODS? ? ?********* ??111 YEARS-YOUNG STEEL TRUSS, (1898): ?STILL VITAL SEA-T0-SEA RAIL LINK? ? ?********* ??51 YEARS HAVE PASSED SINCE SEAWAY (1958) ?SWITCHED BRIDGE INTO DOUBLE LIFT SPANS?

May 1, 2011

By E. C. Morton

The Western Australian School of Mines (WASM) has developed a facility for the static testing of large scale ground support elements. The samples are loaded using a mechanical screw feed jack. Instruments measure the displacement and the load being applied. Methods have been developed for testing of mesh, shotcrete and membranes. Mesh samples are restrained on all sides and loaded centrally. A new large scale punch test method has been developed to evaluate shotcrete and membranes. These products are sprayed on to a sandstone substrate containing a centrally located isolated disc. The sprayed product is loaded by displacing the disk. The different test methods are described in detail. The test program involved two types of mesh, several shotcrete mix designs with different curing times and one membrane product. The force-displacement responses are used to directly compare the products. The implications for implementation of the different ground support products are discussed.

May 1, 2009