Search Documents

By P. Hale

"The trend to drives of more than 10,000 hp on large-capacity ball and autogenous mills for increased operating efficiency has been limited by factors in the conventional drive system. A solution to this problem, using modern developments in static converter technology, is the concept of driving the mill directly without gearing using a low-speed, low-frequency synchronous motor with a cyclo-converter power supply.This paper presents various practical arrangements of mill and low-speed motors giving the specific advantages of each system. The means of controlling inrush currents on starting and of spotting by the use of variable-frequency control are outlined in general form. Several gearless ball mill drives are scheduled for start-up in European cement plants and further orders have been placed."

Jan 1, 1970

By S. Malkin, Z. Shi, H. Attia, D. Chellan

An experimental investigation is reported on creep-feed grinding of a nickelbased alloy (IN718) using conventional aluminum oxide grinding wheels. Straight surface grinding expe.riments were conducted on nickel-based alloy blocks over a wide range of grinding conditions with straight oil as- grinding fluid applied at high pressure. Grinding power, forces, workpiece surface roughness, and radial wheel wear were measured. Specific material removal rate as high as 64 mm2/s was Used without burning the workpiece, which can be attributed to the extremely low specific energy of 12.6 J/mm3. It was found that the grinding wheel under the present test conditions had a strong capability of self-sharpening as indicated by the stabilized power, forces, and surface roughness after an initial short transient.

Jan 1, 2006

By E. De Souza

Two comprehensive surveys, which focus upon backfill practices and the economics of backfilling in underground mines in Canada, have been conducted. The two surveys were designed to assess operational practices and costs associated with the wide scope of filling operations that must be met by individual mines, ranging from raw material feed to the preparation plant, through underground backfill transportation, to in-stope product placement. This paper presents the current state of backfill usage in Canada, identifies trends in minefill practices and provides mine operators with an updated database of information upon which they might compare their own practices and costs with present trends throughout the industry.

May 1, 2003

By D. Stone

"The Beal Mountain mine near Anaconda, Montana, is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of approximately 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges."

Jan 1, 2002

By Rui Wang, Engang Wang, En Jiang, Anyuan Deng, Xingwu Zhang, Fei Wang

In this paper, the rectangular strands of Incoloy 800 superalloy were fabricated with a pilot vertical continuous caster in Northeastern University, China. In the processing, an electromagnetic stirring (EMS) is applied on the secondary cooling zone to control the solidifying structure and segregation of elements in the strands. The solidification structure of Incoloy 800 superalloy strands were investigated at different electric parameters and casting parameters. The research results show that the EMS can effectively restrain the dendrite growth and increase the ratio of equiaxed grains in Incoloy 800 superalloy strands as applied a suitable electric parameters and cooling condition in the process of continuous casting. The evolution of dendrite crystallization in Incoloy 800 alloy strands from the surface to its center during the solidifying process was investigated with and without EMS.

Jan 1, 2014

By Julia Pflieger, Manfred Russ, Johannes Gediga

This paper shall show an economic feasible approach to implement Greenhouse Gas (GHG) reduction measures into the mining and metallurgy industry. The goal to improve energy consumption is directly linked to the reduction of GHG emissions and therefore directly in correlation with the economic viability. A baseline scenario of the considered reference system and of the respective reference year has to be defined, mapped and analysed. In a second step an analysis of the same operation using available and prospected Best Available Technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified reduction potentials are reported and the GHG emission reductions are put into relation to the investment cost of the new process technologies / process adaption to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap implementation into the company's business operations. The GHG reduction roadmap is developed using ratios between GHG reduction and investment / operating cost to get an indication for a sequence for implementing carbon emission reductions measures.

Jan 1, 2010

By G. B. Harris

A process for the recovery of copper from the waste oxide copper of a mined-out sulphide orebody is described. Hydrometallurgical recovery of copper from this and similar wastes has been tried several times previously without success. Leaching is carried out by sulphuric acid in columns under conditions that minimise the iron content of the pregnant leach liquor, and copper is then recovered by ion exchange rather than the more conventional solvent extraction. The resin is stripped by spent electrolyte and copper is electrowon. Results are presented for testwork originally carried out in 1993, and repeated in 2006, and the novel aspects of the process, leaching and ion exchange, are discussed. Finally, preliminary order of magnitude capital and operating costs are given, demonstrating that the process is cost effective.

Jan 1, 2007

By H. R. Stoger

"In 1994 world trade grew by 9%, the fastest annual increase since 1976. Dry cargo shipping rates are at an all time high.Panamax size bulk carriers are receiving19 000 US dollars per day for trans Atlantic round trip voyages. This is good news for the ship owners but not such good news for the industrial users of ocean shipping.The main emphasis of this paper will be on bulk carriers, the charter market and what industrial companies can do to reduce their costs of ocean transportation which is critical to Canadian exporters. Let us look at the charter market in general.Bulk carriers come in four main sizes:1.The Capesize bulk carriers of 110 000 to160 000 tons that are primarily used to transport iron ore and coal;2.the Panamax bulk carriers of about 70 000tons dwt. This is the largest size (with a beam of 105 ft) that can transit the Panama Canal.3.the Handymax bulk carriers of 40/45 000tons dwt; and4.the Handysize bulk carriers of 20/35 000tons dwt.The handysize vessels are usually craned or geared and carry a variety of bulk cargoes including steel. Ship sizes have increased over the years and the mining industry now uses primarily capesize or Panamax bulk carriers.International chartering is conducted through an international network of shipbrokers. There is usually one broker representing the ship owner and another broker who represents the charterer. The major chartering centers are London and New York but a great deal of chartering activity is conducted in regional markets such as Hongkong, Oslo, Montreal and Hamburg.The Biffex Index or Baltic Freight Index is a good measure of dry bulk freight rates. The Biffex is composed of ten major routes. In May1995, the Biffex was at 2310 points. A year earlier it was at 1354, an increase of about 56%."

Jan 1, 1996

"Here, we statistically proved that giant earthquakes occur at lunar phases specific to each subduction zone. Enough attention during the lunar period, especially when seismicity is occurring, will significantly reduce damage from giant earthquakes. Two case studies in which giant earthquakes occurred after seismicity in dangerous lunar phases were discussed, and the mechanisms underlying why giant earthquakes occur around neap tide at some subduction zones were explained by prohibition of giant earthquake occurrences due to high strain rates at spring tides at N–S subduction zones. The prohibition was statistically proven for uniaxial creep tests on Inada granite with slight stress disturbances. INTRODUCTIONIn previous studies, we showed that from 1900 to present, giant earthquakes (MW ??8) have occurred at lunar phases specific to each subduction zone (Fujii & Ozaki, 2012; Ozaki & Fujii, 2012). Although we later proposed a possible reason for these occurrences, the study lacked statistical analyses (Fujii et al., 2013). Therefore, this paper shows the results of such statistical testing and presents case studies for the Tohoku 2011 and Chile 2014 events, thereby providing updated data on giant earthquakes through July 2014."

Jan 1, 2015

By B. I. Whittington

This paper examines the effect of cation type (i.e. NH4+, Na+ and K+) and anion type (i.e. SO42- and C1-) on the extraction of nickel during the pressure acid leaching of a Western Australian laterite ore. The results are compared with testwork conducted with other Western Australian nickel laterite ores and the possible process implications of adding an additive to a plant autoclave are considered. Addition of either (NH4)2SO4, Na2SO4 or K2SO4 increased both the nickel extraction and the acid consumption, provided that the level of additive was not too great. For example, the nickel extraction of 93% increased to above 96% in the presence of additives, but decreased to 94% when, for example, NH4 levels increased from 7 kg/t ore to 21 kg/t ore. The relative stability of the jarosite species formed when additives were present influenced the amount of jarosite in the residue and, hence, both the final free acidity and overall nickel extraction. The use of Cl- versus SO42- salts as additives had little effect on overall nickel extraction or overall free acid values, although the presence of SO42- additives appeared to enhance nickel extraction kinetics over the first 60 minutes of the reaction. In contrast, manganese extraction was enhanced by the presence of Cl- additives.

Jan 1, 2004

By C Kumar

Scaffolds are temporary structures built to facilitate construction activities on site. A considerable amount of resources are allocated to scaffolding on industrial projects. Variability in geometrical features and space accessibility of structures on industrial projects, in addition to involvement of different trades that share the use of scaffolds, requires an extensive understanding of scaffolding requirements. Hence, it?s important to plan and estimate scaffolding man-hour requirements for the different construction areas on an industrial site. Contributing factors involved in such estimates include the list of trades that work in a construction area, trade working hours, volume of work, geometry of equipment erected, etc. A simulation template for predicting scaffold erection man-hour values for individual construction areas in an industrial project was developed in Simphony 4.0. The template is based on mapping the geometry of equipment and other factors to man-hours of scaffold work. The template facilitates the use of distributions as inputs and produces a range estimate of scaffold man-hours. The mapping is based on a linear regression model derived from existing project data from PCL Industrial Management Inc. The template is being further developed to incorporate the ability to predict scaffold erection schedule and material requirements based on construction work areas or equipment lists of an industrial construction project.

Aug 1, 2013

By N. Saracoglu, R. H. Wallis, J. E. Betz, F. L. Jagodits, B. R. Krause

"Geophysical test surveys were conducted with various methods (EM, lP, gravity and magnetic) over the McClean uranium deposits of the Canadian Oxy- lnco Joint Venture. The result s were assessed to judge the contribution each method might make toward further discoveries of graphite-associated uranium occurrences.The best drill targets have proven to be discontinuities in graphitic conductors and locations where the tatter are intersected by fracture zones in the Athabasca. The tests demonstrated that the preferred combination of geophysical survey s is horizontal loop EM to locate graphitic conductors in the basement and VLF-EM to locate the fractures.IntroductionThe discoveries of the McClean North and South uranium deposit s (Fig. 1) are essentially geophysical successes resulting from drilling MaxMin delineations of INPUT airborne electromagnetic responses (Saracoglu et al., 1983). After the initial discovery in 1979, various geophysical methods, techniques and instruments were employed to test their effectiveness in this environment and to guide exploration for other deposit s of a similar nature in the remainder of the 260 km2 property.The McClean uranium deposits lie below 150 m to 180 m of overburden and Athabasca Group. Radioactive signatures might be expected; however, the Athabasca Group acts as a barrier to radioactive emanations. Fortunately, the uranium mineralization is associated with graphite in the crystalline basement. Prior drilling of ground electromagnetic anomalies confirmed that EM surveys could locate and out line basement graphitic conductors. However, as there were many anomalies, most of which could not reasonably be expected to be associated with uranium , there was need to identify additional parameters, related to mineralization, which could be detected geophysically and used to narrow the search."

Jan 1, 1986

By D. Stüben, G. P. Glasby

"Abstract - Shallow submarine hydrothermal fluids from Paleohori Bay off the Greek Island of Milos have been investigated in detail. The extensive gas and warm (max. 93°C) water vents are enriched in major components such as C1-, Na+, Si, Ca2+, Mn, PO4 3-, NH4 +, K+, Sr2+, H2S and CH4 and depleted in Mg2+, O2 and SO4 2- relative to ambient seawater. Based on zero-Mg calculations, it is deduced that the submarine vent fluids are related to the geothermal reservoir beneath Milos which has a similar chemical composition. Fluid samples from each vent in Paleohori Bay represent a mixture of hydrothermal end-member fluids derived from the upper and deeper geothermal reservoir systems of Milos, a mantle-derived source, a high-chloride fluid resulting from phase separation of geo thermal fluids and a steam-heated CO2-rich meteoric water. Résumé - À l’île de Milos dans la mer d’Égée, des fluides sous-marins hydrothermaux en eau profonde ont été récherchés en détail près de la baie de Paleohori. Les larges émanations de gaz et d’eau chaude (temperature maximale: 93°C) sont enrichies en constituants principaux tels que de Cl-, Na+, Si, Ca2+, Mn, PO4 3-, NH4+, K+, Si, Sr2+, H2S et CH4 et appauvries en Mg2+, O2, SO4 2- comparé à l’eau de mer environnante. Selon le calcul du zéro-Mg, nous en déduisons que les fluides sous-marins hydrothermaux sont dérivés du réservoir géothermal sous l’île de Milos car leur composition chimique est la même. Les prélèvements des fluides de chaque source hydrothermale représentent un mélange de fluides hydrothermaux dérivés des réservoirs géothermaux supérieur et inférieur, d’une source dérivée du manteau, d’un fluide très enrichi en chlorure produit par la séparation des phases et de l’eau météorique enrichie en CO2 et chauffée par la vapeur."

Jan 1, 1999

By André Piché

"Over the last ten years, several developments have been undertaken to conceive a machine capable of carrying out simultaneously all the mining tasks in hard rock deposits: cutting, mucking, hauling, ground support and dust control.The main advantages of continuous mining over conventional drill and blast is the elimination of the cyclical nature of the actual methods. Other advantages sought are improved stability of mine openings, higher productivity, lower costs, and a cleaner and safer mining environment. Noranda has con-tributed to these developments in a major way. As a member of HDRK, Noranda participated in the development of two mechanical continuous mining machines; the TM60 and the Wirth. Noranda also undertook a development of its own based on the utilization of electricity to break rock. This technology is called plasma blasting (PBT). The concept of plasma blasting is illustrated in Figure 1.When the operating voltage is reached (18kV), the energy is released through a high current switch (500k A) into a coaxial powercable. It is then delivered to the tip of an electrode inserted into a drill hole which is filled with an electrolyte (water). When the energy reaches the electrolyte, it is instantaneously transformed into a high temperature, high pres-sure plasma that produces a shock wave capable of breaking rock(1).After initial testing of the plasma blasting technology in the lab and in the feld, two experimental platforms were constructed. The first one, a test bench, was erected at the Noranda Technology Centre in Pointe Claire, Quebec.(2)The second one is a rock breaker prototype based on a standard diesel-powered carrier (Fig. 2). Each platform was equipped with a 300 kJ pulsed-power module.In 1993, the rock breaker prototype was used for an extensive series of tests in the field. During that campaign, over 700 oversized boulders were blasted. The results of the tests demonstrated that more durable components for PBT were needed. The test bench was then used to successfully develop and test long-lasting components (probe, switch, cable, connector) that can be adapted to industrial platforms leading to the commercialization of the technology."

Jan 1, 1996

This work illustrates the potential of two welding processes for joining AA1100-16 vol.% B4C metal matrix composite: laser welding process using a 4 kW Nd:YAG laser and Friction Stir Welding. A comparison is made between these two welding techniques in terms of microstructure and mechanical properties of welded joints. A large amount of brittle needle-like phases, together with some residues of B4C particles were observed in the fusion zone of laser welded joints. The use of Ti filler can improve the microstructure and increase the joint efficiency from 63% to 75%. On the other hand, the friction stir welding process being a solid state welding technique is interesting as it avoids the formation of brittle intermetallic phases. In addition, the breakage of B4C particles and the grain refinement of the matrix were observed in the weld zone. Consequently, FSW joints show much better mechanical properties than laser welded joints. Up to 100% joint efficiency can be achieved by FSW for annealed AA1100-16 vol.% B4C materials.

Jan 1, 2011

By M. Marchese

It is no secret that scarcity of fresh water is an issue that at a global level in the years to come will have a major impact on the business landscape. A number of projects, beyond the mining sector, could remain on paper only due to this. At the same time, this situation is seeing the rise of new business opportunities, such as development of technologies for more efficient usage of water, water recycling, and desalinization of sea water. Despite that most of Chilean mining facilities are located in the driest area of the world, business has developed strongly and actively for more than a century. However, the negative effect on the water reservoirs and the environment is, lately, resulting in the reduction of the authorized water rights. Holding Water Rights for any given volume does not guarantee that the resource will be available when needed. A recent report from the United Nations on global climate change indicates that global warming can be directly related to changes in the natural and human environment. Chile would not be an exception. The reduction in snow levels in the high Andes and reduced rainfall during the so called "Bolivian winter", have directly affected the replenishing of the underground water reservoirs in the lower parts of the valleys, where most of the extraction of the resource takes place. Mining facilities shall be designed to reduce potential environmental effects, using proven technologies, and considering the best practices available. These measures shall constitute a complete structural framework for the environmental impact assessment (EIA) of the Project. The measures to prevent and mitigate the impacts on the water resources shall be considered during the design stage of a mining project. Current and future mining projects in Chile are conscious that the increasing pressure on the limited water resources is becoming unsustainable, and are already facing the water scarcity and social pressure by implementing sea water desalination plants, including long pressurized pipelines to the mine sites (e.g. Escondida, Candelaria, El Morro, Regalito). This paper presents, in summary, an analysis of the present and potential future scenarios.

Jan 1, 2007

Drilling is a common process in mining and petroleum engineering applications which have different objectives. For example, drilling deep boreholes in tight gas formations and gas shales is becoming more popular in the oil and gas industry. By contrast, drilling deep small sized holes for mineral exploration in hard rocks is performed to obtain samples for grade analysis purposes. In both applications optimising the drilling process includes using the most effective operating parameters such as rotation speed and weight-on-bit in order to maximise the rate of penetration. Obtaining the optimum drilling parameters requires sensitivity analysis over a range of data, which would be costly and time consuming during real field operations. Therefore, conducting several experimental simulations in the lab would be very beneficial before field operations begin. A drilling rig was designed and developed to simulate various drilling scenarios. The rig works in conjunction with an existing true triaxial stress cell (TTSC) which is in use for different petroleum related applications. The rig allows drilling into a cubic rock sample of up to 300 mm size. Three independent stresses can be applied to the sample to simulate real in-situ field stress conditions while the sample may be saturated with fluid. A significant feature of the rig is its ultra-high speed rotation which can rotate up to 8000 rpm: this is to simulate hard rock drilling for mineral exploration applications where large weight-onbit could damage the bit cutters. With the proposed design, a drilling fluid of any type can be circulated in the simulated borehole similar to the real situation, to study its effect on drilling performance. The TTSC drilling lid is equipped with torque and drag measurement systems which are two important drilling parameters to be recorded during drilling operation. It is believed that this new drilling rig will open opportunities for performing major new applied research in the area of more efficient drilling in both oil and gas bearing formations and mineral exploration applications.

Aug 1, 2013

By T. T. Chen

A detailed mineralogical study was carried out to characterize the products generated in a conventional copper refinery anode slimes treatment circuit. The anode slimes, which are first leached in sulphuric acid media under an oxygen pressure to dissolve the copper and much of the tellurium, were found to contain various Ag-Cu selenides, PbSO4, Ag, Au and BaSO4. The resulting Ag2Se, Ag3AuSe2, Se, Au, PbSO4, BaSO4, SnO2 and silicate-rich leach residue is dried and pelletized. It is subsequently roasted to convert the selenium to Ag2SeO3, volatile SeO2 and water soluble Na2SeO4. The roasted product, which was found to consist of Ag2Se, PbSe, PbSO4, BaSO4, Ag3AuSe2, Au and Sn02, is smelted and refined in a Dore furnace to produce a Dore metal that contains a (Ag,Au,Pd,Cu,Pt) alloy together with traces of CuO and a Cu-Pb oxide phase. Parting plant mud shown to contain AgC1, Ag, Au, (Au,Ag,Pd), Ag2Cu2O3 and Ag20, and scrubber mud containing PbSO4 and AgC1 are also fed to the Dore furnace. The Dore furnace sequentially separates a silica slag which was found to consist of Ag, Sn02, BaSO4, Pb-Sb oxide, Fe-Sb-Ni-Cr oxide and a Pb-rich silicate phase, a soda-rich slag containing Na2CO3.H2O and Na2(Se,Te)03, and a niter slag containing Na2TeO3, Na2(Se,Te)03 and a Na-Te-Se-Pb-Ba-Cu oxide phase. The Dore metal is electrorefined in Moebius cells to yield high-purity silver and a gold mud which was shown to consist of a (Au,Ag,Pd,Cu,Pt) alloy and traces of CuO. Silver is leached from the gold mud and the resulting gold sand is cast into anodes and electrorefined in Wohlwill cells to produce pure gold.

Jan 1, 2007

By Christopher A. Jacobs

Project managers aim to maximise the NPV of their projects, but don't always appreciate the relationship between mine throughput, project value and the discount rate being used to evaluate their projects. Rate of production or throughput is perhaps one of the most crucial decisions a project manager must make, but if this choice is made arbitrarily, much effort may be spent on a feasibility study that does not optimise project value. The timing of the study in relation to the stage of exploration is examined and simple techniques are presented that project engineers and managers can use to home in on a production rate which will give their project the greatest chance of success.

May 1, 2006

By Lynn I. Kelley

Potash is the primary industrial mineral produced in Saskatchewan, followed, in terms of gross value, by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium chloride brine and "clinker." Potentially economic deposits of kaolin, diamond and building stone are under evaluation.

Jan 1, 2001