Search Documents

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By E. Heikkinen, J. Suikkanen, T. Siren, J. Valli, M. Hakala

Diametrically faced borehole breakout observations are a fairly good indication of magnitude of the secondary stresses acting perpendicular to the borehole. In cases of low in situ stresses, where borehole breakouts are not observed naturally, it is possible to increase the prevailing stress state around the borehole by increasing the rock temperature. When the temperature is increased sufficiently, thermally induced borehole breakouts will occur. By implementing the temperature increase in boreholes located at excavated tunnels, it is also possible to study the effect of the near-field stresses caused by the excavation. The near-field stress state changes as a function of borehole depth, thus increasing the information available from experiment. To study the feasibility of this proposed low cost method, a Borehole Thermal Spalling (BTS) experiment was executed in ONKALO Underground Rock Characterization Facility, in Western Finland in 2014. The first borehole pilot test with the method was conducted in ONKALO at the POSE niche in already at May 2010, with the second pilot test following in August 2010 at Äspö HRL. The major objective of the experiments was to define the trend of the maximum in situ stress component, while also providing knowledge of the in situ spalling strength of the ONKALO rock mass. The stress state in ONKALO is nearly isotropic in horizontal layer, causing problems for the use of more traditional stress measurement methods. With boreholes heated over long interval, the weakest rock parts are observed to fail, thus providing statistical confidence. For these reasons, continuous test sections have an advantage in ONKALO, compared to spatially limited stress measurement methods such as overcoring and hydraulic fracturing. The BTS experiment is conducted in 9 meter deep vertical boreholes located at the POSE niche, situated -345 m depth below the ground surface. The boreholes used within the BTS experiment are located in migmatitic granite, in an experiment area where the surrounding stress state and the rock strength are fairly well known. The prior knowledge of the stresses is favourable for the experiment, as it requires careful planning and iterations to determine the appropriate heating power domain. Too low heating power will not be sufficient to cause borehole breakout, while too high heating power causes breakout in all directions thus making determination of stress direction hard or impossible. The initial state of the borehole and induced borehole breakouts will be monitored using acoustic televiewer logging (ABI) and optical borehole logging (OBI) imaging techniques. Fracture mechanics modelling is used in planning of the experiment, also in back-analysis to link the observed breakout angle to stress state. Both the pilot test in 2010 and BTS test in 2014 resulted in similar borehole breakout direction. The results are in line with so called EDZ & VT1 stress interpretation, revealed the maximum horizontal component bearing the magnitude of 21.5 MPa, with the trend of 166°.

Jan 1, 2015

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, W. L. Mason, John J. Justen

"A miscible displacement pilot, using a slug of LPG driven by separator gas, was conducted in the Cardium Reservoir of the Pembina Field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gas phase, an .experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to cakulate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones, and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in con-trolling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir."

Jan 1, 1960

By John S. Stevenson

THE Twin "J" Mine, operated by Twin "J" Mines, Limited, represents an amalgamation of the old Lenora, Tyee, and Richard III mines (see Figure 1) on mount Sicker, eight miles by road, northwesterly, from the city of Duncan, on Vancouver island. These mines produced 253,000 tons of copper-gold ore between 1898 and 1909 (see Table I). During the more recent period of production from these properties, July, 1943, to May, 1944, Twin ?J? Mines, Limited, mined and milled ore with values mainly in copper and zinc, and minor values in gold, silver, and lead. Figures are not available for this later production. Field work at the property was started by the writer in 1941 and continued in 1943 and 1944.

Jan 1, 1945

By Mario E. Rossi

Geostatistical conditional simulations are becoming increasingly popular as tools that provide models of uncertainty at different stages of a mining project. They have been used as grade control tools in daily operations, to assess the uncertainty of minable reserves at the project?s feasibility stage, and to assess mineralization potential in certain settings. Other applications include assessment of recoverable reserves, resource and reserve classification, and drill hole spacing optimization studies. All large-scale applications of conditional simulations intend to benefit from the ?correct? (or ?accurate?) characterization of uncertainty, adequately describing the variability observed from the data and its impact on the final objective. The objective of this paper is to compare the ad-hoc ?uncertainty model? provided by a traditional classification scheme with the probability intervals resulting from a conditional simulation model. It is argued that the uncertainty model derived from the use of classification schemes is of little practical use to the mining company or operation. The paper emphasizes differences in uncertainty based on the size of the mining unit considered and the extraction method, and local geological differences. Most importantly, it discusses confidence intervals for these mining units, as compared to the relative precision envisioned by a typical classification scheme. The application described in this paper is taken from a medium-sized Cu open and underground mine in northern Chile, and it demonstrates the impact of several variables on the resulting conditional simulation models. It also compares a more ?traditional? resource classification scheme applied, and the wide difference in local confidence intervals for each mining unit.

May 1, 2001

By J. A. Harle

Introduction When considering power in Alberta, there automatically come to mind ideas of either hydro or thermal generation, leaving in one's thought an uncertainty as to which one would propose. There is frequently an obvious source of power in some locations on our fastflowing rivers, the major possibilities being described in the report on Surface Water Supply and Water Power of Alberta issued by the Alberta Government in 1948, but it must be realised when reading that report that the sites so described will require extensive geological and other surveys before they can be exploited, and account must be taken also of the transmission distances involved in each instance. From a conservation point of view, where water power can be economically developed and power transmitted to the load centres, this should be done, and our thermal resources should be husbanded for our coming generations, especially if our water resources are falling owing to glacial shrinkage.

Jan 1, 1951

By J. W. Craig

CHROME ore, which is used in Canada in the production of ferro-alloys, in a variety of refractories, and indirectly in many chemical industries, is both commercially important and scientifically interesting. The sight of chromium metal is familiar to all of us in the home, the office, the automobile. Chromium is synonymous with armaments: it is understood to be one of several essential metals in tanks, which played an important role in the defeat of France in the spring of 1940. Chromium, in other forms, comes into our daily lives by way of paint and leather, of the familiar green ginger-ale and beer bottles, and more indirectly in every pound of steel produced in the .Dominion. Necessary to our civilization in peace and war, the ores of chromium occur in many corners of the earth. This paper attempts to describe the chemical constitution of chrome ores, their world distribution, and the various chrome products and their industrial applications in Canada.

Jan 1, 1940

By Mengsu Hu, Yuan Wang, Jonny Rutqvist

Material interfaces and typical boundary conditions are boundaries influencing the existence, uniqueness and stability of numerical solutions of water flow in heterogeneous media. The Numerical Manifold Method (NMM) with a two-cover-meshing system is an ideal method to handle boundaries, considering its flexibility with no need to adjust mathematical nodes onto boundaries, the meshing efficiency, and its integration precision. In this study, we derive and compare two new approaches for boundary constraints, i.e., a discontinuous approach with Lagrange multiplier and a continuous approach with jump function in the frame of NMM. In the discontinuous Lagrange multiplier method (LMM), Dirichlet boundaries or the material interfaces are regarded as discontinuities which are linked by Lagrange multipliers. In the continuous Jump function method (JFM), the material interfaces are regarded as inner interfaces, where the refraction law is realized by constructing jump terms with discontinuity of hydraulic gradient in its normal direction. Both the continuous and discontinuous approaches make full use of the aforementioned advantages of NMM and are established based on a clear physical meaning of water flow by our energy-work seepage model. The newly derived boundary-constraint approaches were coded into an NMM water flow model and tested for precision and efficiency on different simulation examples. We first tested both LMM and JFM for an idealized heterogeneous model, comparing the numerical results with analytical solutions. Then we tested both approaches with a heterogeneous model and compared the results of hydraulic head and specific discharge. We proved that both approaches are very suitable for material boundaries considering the accurate realization of the boundary constraints and the flexibility with no need for mesh-conforming.

Jan 1, 2015

By Louis Frost

"A FIRE which forced the sealing -of the east side of Dominion No. 16 Colliery in the Town of New Waterford, Nova Scotia, occurred on October 6th, 1952 (Figure 1).So far as can be ascertained, the fire was first noticed in the roof of No. 7 East Lateral, after a brushing shot had been fired in the pavement. There appears to .be no doubt that this shot •blew out, igniting a small feeder in the roof.Regular air measurements and air samples, taken over a long period prior to the fire, indicated that the ventilation was adequate, for at no time had the percentage of CH4 in the general air current exceeded one per cent in this location. The last regular monthly samples and air measurements, taken at the end of September, showed the condition of the ventilation to be:Return at the Top of No. 8 East WallQuantity .... 27,700 cu. ft. per min.CH4 .......................... 0.32 per centC02 ................................ 0.10 per centHowever, in the week preceding the fire the mine examiner on four occasions had reported small feeders of gas at the face of the brushing in No. 7 East Lateral.Figure 2 is a diagram of the working place where the shots were fired. The face brushing had been shot down at 3 :45 p.m. and cleaned up. Two 'hurdle screens' had also been erected, one close to the face brushing and the other fifteen feet from the face."

Jan 1, 1953

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By S. Dominguez, E. Gebrehiwot, S. Richardson, S. Sandoval

Copper electrowinning/electrorefining (EW/ER) is powered by direct current (DC) rectifiers that typically generate 30,000 to 70,000 amps and a bus-bus voltage of 200 to 500 volts DC. Tankhouses are designed so that DC current flows through “cell lines” which contain individual EW/ER cells electrically connected in series. Electrolyte composed of copper sulfate and sulfuric acid in water forms the “liquid conductor” that connects the metallic conductors in this circuit. In this setting, stray current is a DC current that strays from and therefore bypasses the tankhouse circuit by finding a path to ground, often through the electrolyte in pipelines that feed into and discharge from the cells, or through dried electrolyte (i.e. sulfate), which is also electrically conductive. Tankhouse workers can be exposed to shock hazards if they become part of a stray current path to ground. This presentation details examples of stray current shock hazards in electrolytic tankhouses and provides voltage and amperage measurements associated with stray current in these examples. A review of critical safety controls in EW/ER tankhouses that will mitigate the risk of employee shock from stray current is also provided. INTRODUCTION Electrolytic tankhouses are designed to deliver relatively large amperages of DC current to a series of electrolytic cells in which copper is plated out of solution using the classic anode-cathode pair geometry within each cell. Electrolyte is the “liquid conductor” that transfers current in between the metallic conductors of the cell. The metallic conductors include inter-cell copper bus bars and the anodes and cathodes themselves. It is sometimes forgotten that electrolyte as a conductor is capable of delivering DC current outside the designed circuit of a tankhouse. Stray current is a DC current that strays from the tankhouse electrical circuit by finding a path to follow other than the designed path. Safety becomes a concern when there is a risk of an employee becoming part of an accidental stray current path, thereby suffering an electrical shock. In 2016, Freeport-McMoRan (FMI) suffered a fatality at one of its copper electrowinning tankhouses. The forensic analysis concluded that stray current from the tankhouse rectifier contributed to the fatality. An employee accidentally fell into contact with a metal flange at the end of an HDPE pipe that was collecting cell overflow electrolyte from the tankhouse. DC current passed through the employee to ground, creating a shock that was judged to contribute to his death. The situation was exasperated because the employee was unconscious, and therefore was exposed to the stray current for several minutes before being found. In addition, the employee’s clothing was saturated with liquid, and the employee was found kneeling in puddled liquid on the ground. FMI immediately began an investigation into the root cause of the stray current that was measured at the scene. Sufficient electrolyte had accumulated in the HDPE pipe such that a continuous path was formed between it and electrolyte that was continuously overflowing from energized electrowinning cells. The metal flange on the pipe was the metallic conductor that carried the current to the employee from the electrolyte inside the pipe. Current then flowed through the employee to ground. Because of this incident, FMI undertook an extensive review of the hazards of stray current in EW/ER. FMI’s tankhouse workforce received a Tankhouse Electrical Safety training course developed in- house to insure worker understanding of stray current hazards. Tankhouse design changes were implemented to better insulate workers from stray current. Personal protective equipment (PPE) standards were also reviewed and changes made.

Jan 1, 2019

By Guichao Wang, Geoffrey M. Evans, Graeme J. Jameson

"In this paper we present a new method for studying the detachment of particles from bubbles in a rotating turbulent eddy. The eddy is formed in a wall cavity in a two-dimensional water tunnel with transparent walls. When water flows through the tunnel, a vortical flow field develops in the cavity. The properties of the eddy can be modulated by changing the free-stream velocity of the water in the tunnel. Bubbles are pre-loaded with one or more particles in a fluidized bed flotation device located beneath the vortex cavity. Loaded bubbles are released one at a time into the cavity, and the motion of the bubbleparticle aggregate is studied using a high-speed video camera. The diameters of the particles and the bubbles, and the number of particles initially attached to the bubble, can be varied. The trajectories taken by the bubbles are quite complicated. In some cases, the bubble moves to the centre of the eddy, and particles rotate around its axis. If the rotational speed is sufficient, particles may detach due to centrifugal force. However, other modes were observed, including inertial detachment due to rapid changes in direction of the surface of the bubble, because of changes in trajectory of the bubble as a whole, or because of pulsations and oscillations of the bubble surface. Clusters of bubbles held together by particles were seen to form and reform. In the traditional explanation for the detachment of particles in flotation cells, it is assumed that particles detach from bubbles rotating in an eddy due to centrifugal force (Schulze, 1977). Although the conditions assumed in Schulze's theory may exist, it is only one of a range of phenomena that can lead to the detachment of particles from bubbles in a turbulent vortex.INTRODUCTIONThe recovery of particles by flotation methods is dependent on the particle size. The recovery in the existing flotation machines reaches a peak for particle size, typically in the range of 20 to 100 µm. This size range varies as a function of the particle’s properties (type and composites). For coarser particles, the recovery drops very quickly (Gaudin, Groh & Henderson, 1931; Jowett, 1980). If the upper size limit can be increased for flotation, dramatic savings in the grinding energy can be achieved."

Jan 1, 2016

By M. Oliazadeh, A. Vazirizadeh

"The inclusion of small amounts of silicon, phosphorus and sulphur in iron ores or concentrates can have a profound effect on the steel making process and thus on the final iron and steel products. In nature however, it is inevitable that iron deposits contain unwanted elements. Each element has its own distinct effect on the final steel product. The effect of high silicon is the formation of gray iron. Phosphorus mainly increases hardness and strength, lowers solidus temperature and increases fluidity and cold shortness. Finally sulphur contamination causes cracks in the iron texture when smelting and forms white iron when casting. Overall, the acceptable level of phosphorus, sulphur and silica in the iron concentrate should be less than 0.04%, 0.15 % and 1.5 % respectively.Scarcity of high grade iron ores necessitates using lower grade ores with higher amounts of impurities. The purpose of iron concentrators is to increase iron grades to an appropriate level suitable for steel making as well as removing impurities. Although many impurities can be traced in the ore, the most predominant impurities are limited to one or two elements. In this paper the beneficiation methods for removing SiO2, P and S are presented, including flotation, and the parameters that need to be considered in the design of beneficiation plants are discussed. Finally industrial cases are discussed along with their metallurgical performance.INTRODUCTIONIn metal sector, value of iron ores and concentrates is determined by iron percentage as well ascontent of:• Useful elements (Mn, Ni, Cr, V, Ti): natural alloying elements in steel• Deleterious impurities (S, P, As, Zn, Pb, K, Na): impair metal properties or complicate operational process in blast furnace• Fluxing components (Si, Ca, Mg,, Al)Sulphur and copper result in red-short, phosphorus is the cause of cold brittleness and arsenic and copper decrease welding characteristics. Sulphur should not exceed 0.15 in commercial ore. Acceptable sulphur content in ores and concentrates for producing sinter and pellets is 0.6%max, as sintering and heat hardening of pellets remove sulphur 60-90%. Phosphorous content in ores, sinter and pellets is limited to 0.07%-0.15%. 0.00.1% As max, 0.1-0.2% Zn max and up to 0.2% Cu are allowed in iron-ore part of the blast furnace burden for the production of standard conversion pig iron. Slag-forming components are divided into basic oxides (Ca, Mg) and acidic (Si, Al). Higher ratios of basic to acidic oxides are preferred since this reduces raw fluxing material."

Jan 1, 2016

By K. Mayhew, K. Murray

The CESL Copper Process was developed as a hydrometallurgical alternative to smelting and refining for copper sulphide concentrates. As the majority of such concentrates contain appreciable gold and silver values, effective recovery of these metals is essential to the economics of this technology. Unfortunately, conventional cyanide processing cannot be used on the residue from the copper process, clue to its unusual characteristics when compared with naturally occurring gold and silver ores. An abundance of elemental sulphur, as well as the presence of cyanide soluble copper, leads to the formation of both thiocyanate and copper cyanide which is detrimental to process economics clue to excessive cyanide consumption. This, however, can be reduced to acceptable levels by process innovations such as pressure cyanidation and cyanide recovery. This paper outlines the successful application of the CESL Gold Process to various gold-bearing copper concentrates from bench to demonstration scale.

Jan 1, 2011

By N. J. Contini, R. W. Knopp

"In March 1988, old Denver flotation cells were removed from Dickenson's Arthur w. White Mill, and a new flotation circuit, consisting of four Prochem rougher cells and a Hydrochem agitated cleaner column, was commissioned. The refractory portion of the gold in the ore is associated with arsenopyrite, therefore the flotation circuit is set up to produce a saleable sulphide concentrate. Tailings from the leach circuit are conditioned prior to being pumped as feed to the flotation circuit. The prototype Hydrochem agitated column has been in operation as a single cleaner stage for rougher concentrate. The effect of flotation circuit changes on gold recovery data, as well as cleaner concentrate production, and development work to achieve the target results, have been investigated. Flowsheet modifications and the resulting circuit performance data, along with test results to date, will be presented.INTRODUCTIONThe mill is capable of treating 1000 stpd of ore averaging approximately 0.30 oz/ton Au. The ore is crushed and ground to 75% - 200 mesh. Gravity concentration, cyanidation, and Merrill - Crowe precipitation yields 84% gold recovery. Detailed descriptions of the comminution, gravity separation, and leaching circuits, as well as background information have been presented elsewhere (Suttill, Van Weert et al). The target cleaner concentrate grade is 1.0 oz/ton Au for custom smelting and refining. Historical gold recovery values of the old circuit was approximately 20% of the gold present in the float feed at the target grade. The recovery value objective set for the new circuit during the planning stages was 50% of the gold present in the flotation feed at 1.0 oz/ton Au in cleaner concentrate."

Jan 1, 1989

By A. N. May

"This paper describes the present approach of the Mines Branch to the problem of measuring the stress condition in the interior of rocks surrounding underground openings. An instrument, which will be referred to as a stressmeter, has been developed at the Mines Branch to measure un-directional stress changes in absolute units. There are two modes of operation of this stressmeter. It can be regarded as a fixed instrument, in which case it is installed at the end of a diamond drill hole and left in position to record any subsequent stress changes taking place. Alternatively, three of the stressmeters can be used in conjunction with a trepanning opera-tion to allow the existing stress condition to be determined. The initial laboratory work and subsequent experiences in the field with the stressmeter are described. All the field development work on the stressmeter was made possible through the co-operation of Canadian Refractories Limited, Kilmar, Quebec."

Jan 1, 1960

By W. P. Campbell

Foreword At the outset, it should be stated that this paper does not pretend to present a panacea for the ills that 'frozen' wells are heir to, but rather is an attempt to bring to the attention of those whose special concern it is, a little theory and some facts, which have been brought to light recently, in connection with the problem of 'freezing' as it applies to naphtha-producing wells in the Turner Valley field, and to draw some conclusions that follow from the facts discovered. It should also be stated that the investigation is not to be regarded as in any sense complete, but in progress. Doubtless new facts will be brought to light from time to time which may modify present ideas on the subject, but whether favourable or contrary, these will be welcomed, as the purpose of the Department is to secure as complete information as possible of the factors contributing to 'freezing', since this must be the first step to an intelligent attempt to remedy or prevent its occurrence, if such can be done. It is possible, too, that the cause or causes of freezing may not be the same in all cases, but whether this be so or not will have to be determined later as new information comes to hand. Introduction One of the worries which must constantly confront the operators of gas-naphtha producing wells in Turner Valley-although all, fortunately, have not met with it-is the possibility of the occurrence of what is commonly called 'freezing' (going off production).

Jan 1, 1930

By D. G. F. Hedley, F. Grant

"In 1958, the Ontario Department of Mines appointed a committee to study the accident situation and mining methods used in the uranium mines in the E1liot Lake district. This committee reviewed the existing knowledge on mine design, pillar support and roof spans and came to the conclusion that scientific knowledge had not yet reached the stage of producing rational design procedures which would reduce the dependence on trial-and-error methods. Since that time, the Mining Research Centre has made numerous stress measurements in two mines to define the pre-mining and pillar stresses. A comprehensive series of tests has been done in the laboratory to measure the compressive strength of the rock; a geological survey of the region has been made to evaluate tectonic stresses; and a survey was done on mining conditions with regard to stable and unstable pillar configurations. This information has been used to evaluate pillar design as effected by pillar width and height, depth below surface, extraction and pre-mining stress fields. The resultant design of pillar widths and corresponding extraction as the depth increased is in line with past and present experience in these mines. The information available on roof stability is still insufficient to design stable stope spans with the same degree of confidence; experience and trial-and-error methods are still required."

Jan 1, 1972

By Liu Liu

In the recent 10 years the rapid development of Chinese steel industry has attracted the attention of the world. The technological progress of converter steelmaking has played an important role in this process. First of all, slag splashing has been extensively adopted by Chinese steel companies in various sizes of converters from largest to smallest ones, and even including those using special hot metal containing V and Ti. Remarkable metallurgical results have been achieved. Up to now the average converter campaign life has reached nearly 10,000 heats, and the longest exceeds 30,000 heats in three melt shops. Based on this process, the long-life combined-blowing converter steelmaking technology has been developed. Slag splashing has been used to form a gas permeable "slag mushroom" on the top of bottom nozzles to protect the nozzles. In order to keep the effective bottom blowing, furnace bottom thickness control technique has been developed to prevent the furnace bottom growth. It makes the service life of bottom nozzle the same as the converter campaign life (average 10,000 heats and longest > 30,000 heats). The complete combined blowing was ensured through out the furnace campaign. Concentration product [C][0] is in the range of 0.0023 ~ 0.0030%, the T.Fe in the slag is lowered by 4 ~ 6%, and the [0] in steel is decreased by 100 ~ 250 ppm.

Jan 1, 2004

By M. Venkatraman

The limit of Hall - Petch relationship in ultra fine grained steels has been examined based on dislocation pile-up mechanism. When the grain size becomes small the dislocation multiplicity ceases resulting in very low work hardening rate in these materials. An approximate analysis of the theories of hardening indicates that H-P relation is obeyed up to 100nm. It appears that grain refinement is not the suggested approach to improve toughness as well as strength below a critical size.

Jan 1, 2004