Search Documents

By M. Silva, G. Olivares

In a leach pile, the drainage layer or commonly known as the cover layer has been a matter of discussion due to the multiple phenomena or events that occur within it which impacts negatively the leaching process. All these events are directly related to the loss of draining capacity and irregular flow net due to an excessive compaction and entrapment of fines reducing the flow velocity which in turn cause more fines to get trapped. Over time the problem will continue to worsen rapidly and accelerating continuously like a geometric progression. When the cover layer gets to a certain level of deterioration, the only alternative to continue operating safely is to replace the entire cover material, a huge cost for any mining operation. TESRA has developed a solution to counteract the accelerated advance of the deterioration of the drainage layer. The solution consists of using large agricultural tractors coupled to a proprietary design of a heavy- duty subsoiler-ripper for deep tillage for loosening and breaking up the ground at various depth and with different legs spacing from 0.4 m or above. Also, if the ground still requires additional breaking, TESRA proposes the use of a rototiller that breaks any lumps to homogenize the ground to a certain particle size. With the subsoiler-ripper/rototiller combination equipment a layer of 0.5 m deep is properly treated to match closely the original conditions of the ground thus regaining the flow net as close as to the original seepage condition. Once the ripping is completed the subsoiler-ripper tool is replaced with another that is similar to a plow and thus continue with the installation of drainage pipes. The tool digs a Y-type profile trench allowing the pipe to sit precisely at the bottom of the trench, contributing additional lateral and lower support. This tool controls the installation depth of the drainage pipe at different inclination grades and also eliminating any irregularities that may block the flow of the leaching solution. Sometimes the obstructions block completely the flow of the solution. The main result of this methodology is the reduction of groundwater levels and at least 2% less humidity in the leaching gravel due to an increase in the draining capacity of cover. The methodology developed by TESRA applied during a couple of cycles of a dynamic leach pile has proven to be a real alternative to remedy and recuperate the cover close to its original conditions. The methodology requires only one large tractor and two accessories operated in different stages while replacing the more traditional and less efficient machinery such as the Bulldozer, Motor-grader, and backhoes.

Jan 1, 2019

By T. C. Chudy, C. C. Hamilton, G. R. Lane

The selection and provision of mineralogical services to assist in developing a GeoMetallurgical program for a Cu Porphyry Mine in South America is covered in this paper and presentation. The objectives of the study were to provide a rapid mineralogical scoping protocol to support and confirm results of sequential Cu leach data and to provide detailed mineralogical analysis of four composites and products on which locked cycle test-work were performed. Results showed good reconciliation was achieved between measured chalcopyrite and secondary Cu mineral contents with leach data using a linear intercept mineralogical procedure by TIMA (Tescan Integrated Mineral Analyser), as well as a generally positive correlation between pyrite and Cu-sulphide grain size. Size-by-size analysis of Composite feeds and test products was used to outline comparisons between feeds on a mineralogical basis and provide liberation and association data with which to diagnose and better explain performance. Identifying key mineralogical drivers to Cu recovery and concentrate grades using these results, a greater understanding of the role of chalcocite and pyrite on metallurgical performance was established. INTRODUCTION As a global supply of copper, porphyry copper deposits are typically very large, often in excess of a billion tons of ore (Keeney, Walters, & Kojovic, 2011; McMillan & Panteleyev, 1980) with grades typically between 0.2 and 1.2% Cu, and up to 2% Cu in places. They are also a source of gold. The complexity of copper porphyries arises from their classically zoned nature, the type of host rock, as well as whether or not they have been overprinted by oxidation, weathering and supergene enrichment (Sillitoe, 2011). Zones of alteration and other geological attributes give rise to varied mineralogy, ore mineral textures and material properties, all of which result in different processing characteristics. Due to the interdependencies of geological and processing characteristics, it is vital to study links between the geology at the macro-scale and mineralogical features down to millimeter and micrometer scale (mineral content and texture) and their influences on mineral processing behaviour (Cropp, Goodall, & Bradshaw, 2013). The growing field of GeoMetallurgy aims to provide an Orebody Knowledge framework by which to gather such information as it pertains to: (1) Understanding and predicting likely flotation response; (2) Guiding relevant test work to investigate and validate links, interdependencies, theories and data interpretation/evaluation; (3) Populate a block model with relevant information and; (4) Implement and refine the model for ongoing optimization and control. Specific questions addressed by using mineralogy often include flotation diagnostics as aids to interpretation, causes of dilution and losses to tailings, as well as guidance to sampling for test work (Cropp et al., 2013).

Jan 1, 2019

By James R. Hein

Manganese nodules form at the sediment surface of abyssal plains throughout the global ocean at water depths of about 4000-6500 m. The nodules form a continuum from purely hydrogenetic (all metals from seawater) to purely diagenetic (all metals from sediment pore waters), which will determine which metals of potential economic interest are enriched in the nodules. Another important factor in metal enrichment is whether diagenesis in the bottom sediment is oxic or suboxic. There are several nodule fields in the deep ocean that have received much attention with regards to economic potential, the most important being the Clarion-Clipperton zone (CCZ) in the NE Pacific, where the International Seabed Authority (ISA) has signed 12 contracts for exploration areas, each spanning 75,000 square kilometers. Those nodules are rich in nickel (mean 1.3 wt. %), copper (mean 1.1 %), and manganese (28%), with moderate amounts of cobalt (mean 0.2%), molybdenum (587 g/t), and lithium (129 g/t). A conservative estimate is that there exists 21,100 million dry tonnes of nodules in the CCZ, yielding more manganese, twice the nickel, three times the cobalt, and four times the yttrium than the entire land-based reserve base (economic plus marginally economic plus subeconomic reserves) for each metal. Total rare-earth elements (REEs) as oxides average 0.09% in CCZ nodules, a potential byproduct even at that grade because the heavy REE complement averages 26%, compared to less than 1% for the large land-based carbonatite REE deposits. The price for HREEs is much greater than for the light REEs. For comparison, the REEs in deep-ocean ferromanganese crusts are 3 to 5 times greater than nodules and the HREE complement averages 18%. Of the 12 CCZ contracts, 7 are with States (China, France, Germany, Japan, Korea, Russia, and a group of States (IOM); and 5 are with companies: G-Tec Sea Mineral Resources NV, Nauru Ocean Resources Inc. (NORI); Tonga Offshore Mining Ltd (TOML), UK Seabed Resources Ltd (Lockheed UK), and Marawa Research and Exploration Ltd. Three other nodule fields that have received attention are in the Peru Basin, which has nodules very rich in manganese (34%) and lithium (mean 311 g/t), the Penrhyn Basin (Cook Islands Exclusive Economic Zone), with nodules very rich in cobalt (mean 0.4%); and the Central Indian Ocean Basin (CIOB), where India has an exploration contract with the ISA. CIPB nodules have mean nickel, copper, and manganese contents of 1.1%, 1.0%, and 24% respectively.

May 1, 2013

"The Schist Lake mine, owned and operated by the Hudson Bay Mining and Smelting Co., Limited, is situated on the northwest arm of Schist Lake, 4 miles southeast of Flin Flon, Manitoba.The deposit was discovered early in 1947, during a diamond drilling program exploring small copper showings along the west shore of the lake. The orebodies came to surface between the mainland and the north end of Stitt Island.Production began in August, 1954, at an initial rate of 300 tons per day. Underground workings have been carried to the 1,700-foot level, where exploration work is now being done.General GeologyRocks of the area are Precambrian lava flows, with associated pyroclastic breccias and tuffs, and related minor intrusions. Their general strike is northwest and their dip is nearly vertical. Shearing is common and is related to the activity which caused intense folding and much faulting in the area. The larger faults and the fold axes trend a few degrees west of north. The lavas are mainly andesitic but a layer of sericite-carbonate schist, which is probably derived from a fine-grained, grey quartz porphyry, occupies most of Stitt Island and extends into the mine area. It is within this layer of schist that the ore deposit occurs (Figure 1).The OrebodiesThe ore occurs as tabular to lens-shaped bodies which strike northwest, dip nearly vertically, and plunge at 60 degrees to the southeast. The ore zone is 800 feet long and has been traced for a distance of 2,000 feet along the plunge (Figure 2). The maximum length of continuous ore within this zone is 200 feet. Widths of individual ore lenses vary from a maximum of 35 feet to a minimum of 2 feet.The ore consists of three distinct types: massive sphalerite-pyrite, massive chalcopyrite-sphalerite, and disseminated chalcopyrite-pyrite. The No. 1, or eastern, orebody is predominantly massive sphalerite-pyrite. The western part of the No. 2 orebody is massive chalcopyrite-sphalerite. The disseminated ore forms the eastern part and the lower end of the No. 2 orebody. All three types of ore, with patchy distribution, are found in the smaller lenses below the 1, 100-foot level.Metallic minerals, in order of deposition, are pyrite, arsenopyrite, chalcopyrite and sphalerite, galena, enargite, and gold. Both massive types of ore exhibit banding in many places, probably as a result of the selective replacement of schist. The disseminated ore was formed as a filling of the interstices in a brittle chert rock which appears to have been crushed by the same forces which produced the schist."

Jan 1, 1949

By W. Petruk

"D. Doyle How large is the beam to which you referred? Are we considering Watts, Griffis the probe of a 1 micron sized particle?& McOuatReply Yes. The beam would be about 1 micron. We could enlarge or reduce it depending on the current in-put.D. Doyle Then chemically bound material we might not see. If you are restricted to 1 micron then you would not be able to separate things smaller than this. Is this not so?Reply We won't be able to analyse it but we will see it as the scanning electron microscope has a resolution down to about 0.1 microns. We should be able to get the general composition of such a grain plus its surrounding grains. We feel we can then make a reasonable estimate if it were as small as 0.1 microns. An accurate analysis would be achieved with grains of 3 and 4 microns.D. Doyle Would this have an application in the hydrocarbon field?Reply The lowest atomic number would be sodium. We wouldn't be able to go below that atomic number. Anything with sodiumor a larger atomic number would enable us to analyse the carbon.M. Fairwether Do you have any policy relating to priorities. For instance areCominco companies going to be limited in the amout of samples permitted to give everyone a chance because quite frankly our company, and I'm sure all base metals companies can hardly wait for the installation of this equipment. I can forsee two years back-log of work in the first month.Reply Quite frankly, I haven't looked at this. At the present time the work is under the START program but I suppose we will have to look at possible changes. Anything under the START program has first line priority.B. Thorndycraft Will the briquetting of samples be automated as well? Pinson MiningReply No, not at this point. Our polish section laboratory is first-class and can turn out 18 polish sections a day which is more thar we can handle.B. Thorndycraft With the capability of this machine to operate in a hands-off manner perhaps it could start to look for the 5 micron gold particle in tailings?Reply I have such a program using a wave-length spectrometer rather than the energy dispersive. The wave-length spectometer is about 10 times as sensitive and would scan the section much faster. A one inch diameter polished section would be scanned in about 7 hours for anything 1 micron or larger."

Jan 1, 1984

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been conducted, thereby providing a unique opportunity to examine the geochemical evolution of a sulfide rich mine>tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% alumino silicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, S042-, Cu, Zn and Pb (up to 10 000 mglL, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively). In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tin oxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SOi-, Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents. Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massivesulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By M. B. McClenaghan

"The Matheson area of northeastern Ontario is of great interest for mineral exploration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has become an important exploration method. The Ontario Geological Survey&apos;s Black River-Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift (< 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (> 3.3 S.G.) and fine (- 250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (< 50 um) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of = 3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By T. Liu, C. Shi, T. Fu, M. Zhong

Water inrush in coal mines is induced by the imbalance of the groundwater flow field and the engineering geo-mechanics field. Therefore, to prevent water inrush it is important to predict the critical hydraulic pressure of water inrush in coal seam floors. This paper will investigate a method for conducting theoretical forecasting of the critical hydraulic pressure of water inrush in coal seam floors by adopting the combination method of a genetic algorithm-neural network. First, the topology structure of a neural network (NN) based on genetic algorithms (GA) will be determined and then the critical pressure of water inrush in a coal seam floor using the chosen NN will be predicted. Finally, theoretical forecasting results will be compared with actual measurement results to determine the feasibility and applicability of this method.

Jan 1, 2008

By F. Chiesa, Jeremy Carignan, B. Duchesne, D. Levasseur

"Aluminium A206 (AlCu4) is one of the strongest aluminium casting alloys with tensile properties approaching those of ferritic ductile iron. If the specification on the silicon content (< 0.05%) is easy to achieve during alloy ingot production, it is not the case in a foundry, where returns are used which are not perfectly cleaned from the silicate containing molding sand (Olivine). In alloy A206, the Si content is controlled in order to avoid the formation of a low melting point intermetallic phase (such as phase Q Al5Cu2Si6Mg2); these phases will melt during the solutionizing heat treatment to which alloy A206 must be subjected to develop its outstanding mechanical properties. This incipient melting may deteriorate the mechanical properties of Alloy A206 if the solutionizing treatment is applied at the standard temperature of 530°C.In the present study, a lower temperature solutionizing (520°C) was applied to a high Si content 206 alloy in order to reduce or eliminate the possible incipient melting. This was carried out on a complex shape industrial casting weighing 14 kg (31 lb) and 560x410x250 mm (22x16x10”) in size poured in aluminum 206 with a high silicon content (0.22% vs 0.05% max for alloy A206). Twenty ASTM E8 subsize tensile specimens were excised from two locations in the casting in order to compare the tensile properties for the two solutionizing temperature used (530 and 520°C). Optical and SEM microscopy allowed to investigate the causes of the differences in the properties observed between the 2 zones of the casting studied for 3 different heat treatments. INTRODUCTIONIn spite of their “textbook” outstanding mechanical properties (Up to twice the strength and elongation of the widely used A356 alloy), aluminum-copper alloys of the 2xx series are seldom used because of their propensity for hot tearing [Li, 2011], the segregation of copper [Cho, 2003], and their sensitivity to stress corrosion cracking [Jean, 2009, p. 113)]. Also, because of their wide freezing range and high thermal conductivity, a wide mushy zone makes feeding difficult, unless strong temperature gradients are created by liberal use of chills and risers in the critical zones of the part. Because they are prone to hot tearing, grain refining of Al-Cu alloys is particularly important, titanium playing a major role in the process [Sigworth, 2003]; grain refining has also been shown to be beneficial to fatigue strength [Jean, 2009, p. 103]. The practical basis of foundry practices pertaining to these alloys is outlined in an AFS webinar [Weiss, 2014]."

Jan 1, 2016

By H. Scott Swinden

"ForewordA symposium on base metal deposits was held in Bathurst, New Brunswick, from June 10-13, 1990, sponsored jointly by the Geological Surveys Branch of the New Brunswick Department of Natural Resources and Energy, the New Brunswick Prospectors and Developers Association, and the Geology Division of the Canadian Institute of Mining, Metallurgy and Petroleum . Papers prepared for the symposuim are being published as a series of articles in the CIM Bulletin. This second paper (the first was by Fyffe, et al., in Vol. 83, No. 938) in the series presents an overview of the paleotectonic settings of massive sulphide deposits in the Dunnage Zone of Newfoundland with emphasis on volcanic geochemistry.ABSTRACTCambrian and Ordovician volcanic sequences of central Newfoundland, which record the history of the Iapetus Ocean, are prolific hosts to volcanogenic massive sulphide (VMS) deposits. Geochemical, isotopic and geochronological studies show that the vestiges of Iapetus in Newfoundland probably record a complex series of island arcs and back-arc basins that were marginal to, rather than part of, the main ocean basin of Iapetus. The geochemical and isotopic data provide a means of characterizing the tectonic environment of individual volcanic sequences, and allow us to identify a number of distinct tectonic environments in which VMS depositiontook place.Four tectonic environments have been identified as being associated with VMS deposition: (I) back-arc environments hosting VMS deposits include both N-MORB-type ophiolites (e.g. Skidder?) and volcanic sequences with oceanic island (or within plate) tholeiite characteristics (e.g. Great Burnt Lake); (2) primitive arc environments include both supra-subduction zone (SSZ) ophiolites (e.g. Betts Cove, Rambler) and volcanic/epiclastic sequences (e.g. Point Leamington, Duck Pond) and are characterized by abundant arc tholeiites, with lesser refractory lavas and rhyolites; (3) mature arc environments comprise dominantly thick felsic and mafic volcanic piles in the Buchans - Robert&apos;s Arm Belt (including the Buchans camp) and are characterized by dominantly calc alkalic basalt and andesite; and (4) continental rift environments occur in the Hermitage Flexure area (e.g. Strickland deposit) and are characterized by dominantly felsic volcanic sequences.Island arc environments are by far the most prolific hosts to VMS deposits. Patterns of VMS distribution in central Newfoundland show that similar tectonic settings may be recorded by very different stratigraphic sequences (e.g. both ophiolites and thick volcanic/ epiclastic sequences may record primitive arc rifting) and emphasize the importance of the rifting in VMS generation, irrespective of the details of the tectonic or stratigraphic setting. The ability to judge the prospectiveness of a volcanic sequence by using whole rock geochemistry to evaluate its tectonic environment may prove useful in area selection at the grassroots exploration level."

Jan 1, 1991

By W. K. Muwais, R. G. Cuddy

"The Lower Cretaceous McMurray Formation contains the bitumen reserves of the Syncrude Mine in northeastern Alberta. This formation comprises sediments deposited sequentially in fluvial, estuarine and marine depositional environments. The Syncrude Base Mine area consists mostly of estuarine sediments, as much of the original marine sediments have been eroded away. These estuarine deposits consist of channel-fill sediments and interchannel tidal flat sediments with the channel-fills comprising most of the orebody.Channel-fills contain, among other lithologies, interbedded sand, silt and clay rich layers that often occur as sequences of inclined beds with dips up to 25 degrees or more. A detailed knowledge of the distribution of these inclined beds, their lithological characteristics and their continuity is very important in assessing the risk of mine highwall instability . Techniques used to identify and characterize adverse structures are reviewed. INTRODUCTIONGeneralThe Syncrude Canada Ltd. oil sand mine is located within the surface mineable portion of the Athabasca Oil Sands area about 40 kilometres north of Fort McMurray in northeastern Alberta, Canada (Fig. I). The company commenced large-scale strip mining of oil sands in June 1977in the area, referred to as the Base Mine, situated in the southeast corner of the company&apos;s two lease areas (Fig. 2).The mining method (Fig. 3) utilizes large electric drag lines operating on a single bench with highwall depths up to 60 metres. Feed grade oil sand (= 6 wt.% bitumen) is mined by draglines and windrowed parallel to the highwall crest. Lower grade oil sand « 6 wt. 0J0 bitumen) occurring as waste bands is selectively mined by the draglines and cast back into the mined out pit or placed on the bench and hauled by truck. The windrowed feed is delivered to the extraction plant by a bucket wheel reclaimer and conveyor system. Stripping of Recent, Pleistocene and Cretaceous overburden units is done outside the conveyor systems by mobile equipment. The 4.5 kilometre long mine is split into four quadrants for planning and scheduling purposes, with each quadrant having an individual dragline-bucketwheel-conveyor system.Surface mining of oil sand at Syncrude requires the removal of vast quantites of material. The design of the open pit mine relies heavily on knowledge of the distribution of ore and waste materials, and on the physical characteristics of these materials.The geology of the oil sand below the dragline bench at the Syncrude Mine is complex. Geological, geotechnical and hydrogeological factors play an important role in the design and operation of the mine. This paper describes aspects of the geology that impact on the design and operation of the mine. Some of the methods and procedures adopted by Syncrude to successfully overcome difficulties that the complex geology creates are discussed."

Jan 1, 1989

By D. T. A. Symons, M. M. Kapnistos

"Gravity profiles were established over five known Middle Silurian pinnacle reef s in Lambton County, southwestern Ontario. The profiles were approximately 3 km long, with stations every 60 m. Four fairly recent technological developments were used which now make the gravity method relatively efficient and inexpensive compared to the techniques available two decades ago. These are: (1) a La Coste-Romberg model G gravimeter to measure the gravitational attraction with a sensitivity of 0.01 mgal; (2) a Sokkisha model B-2 semiautomatic engineers level to measure the station elevations with an accuracy of 0.5 cm; (3) a Huntec FS-3 hammer reflection seismograph to determine the overburden thickness to an accuracy of ± 7%; and (4) a modern microcomputer to process the data sets and mathematically filter the gravity values. Thus, two men can measure and analyze approximately 1 km of profile per day and obtain the residual gravity profile to an accuracy of ± 0. 05 mgal. Positive gravity anomalies of 0.17 to 0.72 mgal were observed along all five profiles that approximately delineate the dimensions of the known pinnacle reefs, which have an average height of 120 m, diameter of 1500 m and depth to top of 575 m. The relative ease of the gravity survey method makes it a cost-effective technique for hydrocarbon exploration in southwestern Ontario. IntroductionPinnacle reefs are important sources of oil and gas. Although the pinnacle reefs in southwestern Ontario are small, they may contain commercial pools of oil and gas because of their proximity to refineries. They are also useful for subsurface storage of gas to meet the winter surge in gas demand.At present, geophysical exploration for new pinnacle reefs is done primarily by relatively expensive seismic methods, which are also limited in southwestern Ontario by prohibitions on blasting. Gravity methods of exploration were attempted more than two decades ago in this region. (Pohly, 1954); however, the level of technology at that time made the method marginal in sensitivity and quite expensive. Several subsequent developments- gravimeters with greater sensitivity and operating ease, ""self-levelling"" levels for elevation control, hammer seismic reflection units for determining overburden thickness and portable microcomputers for efficient data analysis-have significantly improved the precision and cost effectiveness of the gravity method. Five known pinnacle reefs were selected in Lambton County, southwestern Ontario (Fig. 1), to test the effectiveness of integrating these developments to locate and define additional reefs. Isolated reefs were chosen to avoid the problem of the gravity effect s of one reef interfering with those of a neighbouring reef. The surveys were facilitated by choosing reefs with a concession road passing directly over them ."

Jan 1, 1980

By M. C. Ethier, A. L. Laramie

"The Granisle and Bell Copper mines were officially put into production in 1966 and 1972, respectively. The Granisle Mine was purchased in late 1979by Noranda and the two operations were amalgamated as one division. Both mines were closed in 1982after sustaining heavy financial losses during a period of low copper prices beginning in 1981.This paper describes the resumption of operations at the Bell Mine in 1985 after its shutdown period of three years and the dramatic and sustained improvements in productivity and efficiency realized as a result of a commitment by employees and management to the application of Participative Management and Employee Involvement principles. After a general description of the effects of such a philosophy on the operation as a whole, and a comparison to the operation&apos;s last full year as a producer, it deals with the practice of this philosophy in the maintenance department at the Bell Mine and the superb results realized.IntroductionThe Bell Copper deposit was discovered in 1963 and came onstream as a 10000 ton s per day open pit mine in the fall of 1972. Identified reserves at that time were 46 million tons of ore containing 0.50% copper. The mine shared facilities of the townsite of Granisle with the nearby Zapata-Granby mine which had established the community six years earlier.Because of easy grinding ore and improvements to milling circuits, Bell&apos;s throughput rate was increased to 17 000 tons per day by the late 1970s. In the open pit, improvements resulted in mining of additional reserves with higher stripping ratios. At startup, a half ton o f waste was mined for every ton of ore processed.By the end of 1982, with 48.2 million tons already mined, the Bell Mine had identified additional mineable reserves of 39.4 million tons containing 0.52% Cu.In November 1979 the Granisle Mine was purchased from Zapata-Granby. The two mines, with a total of 700 employees, were operated under common management as the Babine Division until 1982 when low copper price s forced the closure of both for an indefinite period.The outlook for copper prices remained bleak and only 50 people were retained on the payroll to maintain the two plants, most of them working on a part-time schedule.The population of the Village of Granisle dwindled from over 1500 inhabitants to under 500, as people moved away to seek other employment.Prior to the shutdown, the Bell Mine employed 370 people and pit extraction averaged nearly 50000 tons per day of which 16000 tons was mill feed, and the remainder waste. Total cost to produce a pound of copper was C$1.36 in 1982."

Jan 1, 1990

By Otto Engel

"A multipurpose program for a hand-held programmable TJ-59 calculator and PC-100C printer facilitates the evaluation of various mineral processing tests and the calculation of mass and metal balances. Its application is demonstrated by some example problems. Detailed user instructions are given for each application.IntroductionThe program listed in Appendix I is written for a programmable Texas Instruments TI-591 PC-100C calculator I printer combination. The program is applicable for the evaluation of:1) screen analyses;2) flotation test s; and3) mass and metal balances.Each application is demonstrated by an example problem and corresponding detailed user instructions. The ""measured"" data in the examples are fictitious and do not represent a real operation.The steps in using the program are the same for each of the three types of application, viz.:1. Enter the number of product fractions and press ""A"".2. Enter the measured weights (0) of each fraction and press ""RIS"" each time. After the last fraction has been entered, the printer automatical1y displays the total weight.3. Press ""B"" to calculate the weight distribution (Y). Once ""B"" is pressed, the printer automatically displays the weight distribution of all fractions.4. If the accumulated weight distribution (EV) is also needed, press ""RIS"". The printer now displays these data. This step is optional and may be bypassed.5. Press ""2nd A"" to prepare for entering of the measured metal assay (M).6. Enter the measured metal assays of each fraction and press ""RIS"" each time. If analytical data exist for more than one metal, each data set has to be entered separately in one sequence.7. Press ""C"" to determine the ""calculated"" head assay (MA) of all fractions.8. Press ""RIS"" to calculate the metal distribution (R). Once ""RI S"" is pressed, the printer automatically displays the metal distribution of all fractions. This operation is optinal and may be bypassed if desired.9. Again press ""RIS"" to obtain the accumulated metal distribution (ER). This operation is optional and may be bypassed.10. Press ""D"" to calculate the gangue distribution in the concentrate (W). One ""D"" is pressed, the printer automatically displays the data for all fractions. This operation is optional and may be bypassed.11. Press ""RIS"" to obtain the accumulated gangue distribution (EW). This operation is optional and ma y be bypassed.12. For more than one metal, press ""E"" to clear the memory for storing the assays of the next. Then press ""2nd A"" and start entering the assays of the next metal as described previously (6 to 11). Steps 5 to 12 may be repeated as many times as desired."

Jan 1, 1982

By J. A. E. Bell

"Inco has shifted part of its traditional extractive research effort at its J..Roy Gordon Research Laboratory in Mississauga toward new, value-added products. Most of the effort is being expended on new Ni powders for batteries and new Ni-coated products which will be produced in Inco&apos;s carbonyl nickel refineries. New products under development are Ni-coated powders, Ni-coated fibres and ultra-fine Ni powders. Other new products for advanced material applications include controlled expansion composites, NiGOLD strip, Thermal barrier coatings on Inco alloys, and plasma coatings.Research and Corporate Strategic ThrustsThe newest strategic thru st of the company is to increase the value of the primary metal products. These new products are to be in addition to any new alloys or downstream alloy fabrication.Historically Inco has had the highest research expenditures in the extractive metallurgy field in North America. This has resulted in many new processes including flash smelting , matte separation, fluid bed roasting, pressure carbonyl refining and cobalt electrowinning which have contributed to establishing Inco as the lowest cost nickel producer. The recession of the 1980s caused a restructuring of Inco research and corporate goals .As shown in Figure I, from 1975-1982, i.e. pre-recession, Inco spent around 33 million dollars per year on research. Some 48070 of that sum was spent in Corporate Laboratories in Sterling Forest in the United States and in the United Kingdom , mostly on alloy associated research. A further 10% was spent on alloy research at the alloy production facilities in Hunting- ton, West Virginia, and Birmingham and Hereford in the United Kingdom. On extractive research, 13% was spent by process technology groups at the plant s, 20% at the pilot plants in Port Colborne and 9% at the J. Roy Gordon Research laboratory.The relative research expenditures (Fig. 2) have decreased so that today they are at the same level as 1975-80. The research as a per cent of sales has been cut from 2.2% to 1.2% of normalized sales. A normalized sale price of $4.00/lb Ni was used in the 1988 figures. This was partly achieved by closing Corporate Laboratories. Most of the essential alloy research was moved to producing plants and total alloy research is now 27%.A new thrust initiated in the 80s was mining research which now accounts for 20% of research expenditures. Over a period of the past five years this research has doubled the mining productivity in Inco. The pilot plant expenditures have been cut in half. One entire research station at Port Colborne was converted into a platinum group metals intermediate refinery. The decrease in pilot plant expenditures has been compensated by full scale plant trials devoted to the S02 abatement program at Sudbury."

Jan 1, 1990

By E. Bratygin, G. Gazaleeva

"The article describes the analysis of methods and criteria of selectivity of optimal ore preparation schemes. Traditional criteria based on study of physical-mechanical properties of ores give the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production.Further on estimation is given to different criteria of the crushing selectivity, the new criterion is offered, the definition of which is done by results of an optical microscopy– the estimation of a valuable mineral release degree. The final estimation of the crushing process selectivity L? is performed by a calculation of a ratio of the valuable mineral free grains quantity in a desired size grade of a crushed material to the valuable mineral free grains quantity in a desired size grade of a raw product.Besides, optimality assessment of using the specific crushing unit is preliminary performed according to a maximum crushing degree of a material, however, the priority is given to the maximum selectivity criterion. The check of the proposed criterion was done when comparing the crushing of niobium bearing ores of the Vishnevogorskoye deposit in cone inertial and centrifugal impact crushers. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion L? showed that the centrifugal impact crusher (CC) has the value of the selectivity criterion lower than the cone inertial crusher (CIC). For the crusher CC the criterion L? is 0.82 – 0.87 units, whereas for the crusher CIC – 1.43-1.755 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 120°, peripheral speed of a cone rotation – 1,420 rpm, specific energy consumption – 6.99 kW?t/t.INTRODUCTIONIt has been shown that the most efficient techniques of mineral raw materials disintegration are selective crushing enabling to produce liberation of particles at maximum use of destruction techniques by borders of minerals cleavage. These days, such techniques are usually called special disintegration techniques (Jankovic & Valery, 2015), and they are used in 3–4 crushing stages. The selection of optimal crushing techniques is performed based on the following main parameters:- degrees of crushing, calculated based on granulometric features of raw and crushed products;- selectivity criterion defined according to useful mineral release and slime ability degree; and- traditional criteria (Gazaleeva et al., 2015) of choice based on study of physical-mechanicalproperties of ores gives the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production."

Jan 1, 2016

By Q. Shi, Q. Feng

"The influence mechanism of chlorite on the flotation of pyrrhotite was investigated through flotation tests, Zeta potential measurements, optical microscope photos, solution ion measurements and absorption measurements. It is observed that, the addition of chlorite influences the flotation of pyrrhotite seriously. The IEP (isoelectric point) of pyrrhotite and chlorite is 7.6 and 4.3 respectively, in the condition of slight alkalinity, both pyrrhotite and chlorite are negatively charged, and the hetero-aggregation will not occur. With the existence of oxygen in solution, the iron ions are dissolved from pyrrhotite surface because of the oxidation of pyrrhotite during pulp conditioning. The dissolved iron ions adsorb onto the surface of chlorite in the forms of iron hydroxyl and iron hydroxide, and the adsorption results in the opposite charge of chlorite surface. As a result, the hetero-aggregation between pyrrhotite and chlorite occurs. The adsorption of chlorite changes the surface property of pyrrhotite and restricts the adsorption of amyl xanthate onto pyrrhotite surface, and then decreases the flotability of pyrrhotite.INTRODUCTIONIn sulfide ores processing, magnesium silicate bearing gangue minerals often report to the concentrate causing downstream processing problems as well as increased smelting costs. Talc,chlorite and serpentine are gangue minerals commonly encountered in complex sulfide ores (Engel, Middlebrook, & Jameson, 1997; Pietrobon et al., 1997; Witney & Yan, 1997; Chen, Grano, Sobieraj, & Ralston, 1999a, 1999b; Bremmell, Fornasiero & Ralston, 2005; Senior & Thomas, 2005; Wang, Somasundaran, & Nagaraj, 2005; WieseHarris & Bradshaw, 2007). All of them are characterized with uniform crystal structures consisting of silicon-oxygen tetrahedron and magnesium-oxygen octahedron. The magnesium-oxygen octahedron layers are broken during the liberation of serpentine to expose the magnesium-oxygen bonds with strong ionicity and hydration, which results in natural hydrophilicity of serpentine. In water, the hydroxyl on serpentine surface ruptures and dissolves into the aqueous phase while the Mg2+ remains, resulting in surface positive charge (Tao, 2012). As serpentine has a positive potential at alkaline condition, it is therefore likely that it will attach through electrostatic attraction to the negatively charged mineral surface and reduce both the flotation rate and recovery of target minerals (Lu et al., 2011). For talc, characterized as good natural hydrophobicity, the liberation comes from the interlaminar fracture to remain molecular bonds on surface with weak hydration. Being naturally hydrophobic, talc easily reports to flotation concentrates, thus reducing concentrate grade (Shortridge, Harris, Bradshaw, & Koopal, 2000; Beattie, Huynh, Kaggwa, & Ralston, 2006). Meanwhile, both molecular bonds and magnesium-oxygen bonds are exposed on chlorite surface when liberation occurs, resulting in moderate natural hydrophobicity between serpentine and talc (Tao, 2012). And thus the mechanisms of influence of chlorite on sulfide ores are more difficult to study."

Jan 1, 2016

By E. Fiset, T. Hennebel, F. Verbruggen, A. Prévoteau, K. Rabaey

Arsenic (As), bismuth (Bi) and antimony (Sb) are known to affect the quality of copper deposits in copper electrowinning operations. The codeposition of As was previously believed to occur only at current densities far exceeding the range of typical current densities for copper electrowinning. In this study, we investigate the copper electrodeposition on different pretreated stainless steel (SS) substrates from bleed electrolyte in galvanostatic mode at –45 mA/cm². Scanning electron microscopy (SEM) micrographs illustrate that during the initial phases of copper nucleation and growth, the current density was locally increased due to the pretreatments. It was reasoned that the codepostion of As could possibly occur in normal electrowinning conditions, but the risk can be substantially reduced by good SS substrate handling and maintenance practices. INTRODUCTION The presence of As, Bi and Sb is known to have a deleterious effect on the copper cathode quality in copper electrowinnings (Hiskey & Maeda, 2003; Hoffmann, 2004; Xiao, Cao, Shen, & Volinsky, 2012; Xiao, Cao, Mao, Shen, & Ren, 2014; Jafari et al., 2017). They are known to influence both the chemical and physical quality of the copper as they can contaminate the copper (Jafari et al., 2017) and affect the copper deposit structure (Hiskey & Maeda, 2003; Kim, Kim, & Chung, 2009), which contributes to a degraded market value of the copper (Tuddenham, 1984). The incorporation mechanisms of these impurities are believed to occur mainly through slime inclusion (F. Xiao et al, 2012) and electrolyte inclusion (Hiskey & Maeda, 2003). Other studies suggested that codeposition of these impurities is possible by their standard reduction potential being close to the one of copper (Xiao et al, 2014). Hiskey and Maeda (2003) investigated the copper electrodeposition on a copper electrode substrate in Cu electrolytes with a Cu, H2SO4, As, Bi, Sb composition representative for commercial copper tankhouses. The combination of voltammographic techniques and Auger electron spectroscopy showed that As was the first impurity to be electrodeposited from this electrolyte, yet at potentials where the limiting current density of the copper electrodeposition reaction is exceeded. The copper tankhouses usually operate at a current density ratio of 0.3 to the limiting current density in order to achieve tolerable copper quality deposits. The codeposition of As could be considered impossible in this current density condition. However, it is known that during the initial phases of electrodeposition on foreign substrates, a substantial part of the reaction proceeds by growth of individual nuclei where the current density is locally high and diffusion limited (Radisic, Ross, & Searson, 2006). Furthermore, it was observed that copper nucleation on TiO substrates occurred preferentially in the scratched oxide free areas which could serve as parts with high localized current densities (Chang, Choe, & Lee, 2005).

Jan 1, 2019

By Lassi Klemettinen, Ari Jokilaakso, Dmitry Sukhomlinov, Pekka Taskinen

The solubilities and distributions of molybdenum and iridium in iron silicate slag and copper-iron mattes were studied using an equilibration-quenching technique and subsequent direct phase composition analyses by EPMA (Electron Probe X-ray Microanalysis) and LA-ICP-MS (Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry). The equilibrations were carried out on a wide matte grade interval, ranging from 55 wt-% Cu to 75 wt-% Cu, in pSO2 = 0.1 atm at 1300°C. The results in equilibrium with a solid iridium-molybdenum alloy indicated an iridium solubility of 150–500 ppmw in the sulphide matte, depending on the matte grade, and a molybdenum solubility of 100–600 ppmw. Iridium was distributing predominantly in the sulphide matte with the distribution coefficient of 10+3 - +4 but molybdenum deported predominantly in the slag with Lm/s(Mo) = 0.02–0.1. The effects of alumina and lime additions in the smelting slag were also examined. INTRODUCTION Iridium is a highly siderophile element (HSE), which means that it is incompatible with the sulphide forming elements and possesses a small solubility in mattes, such as copper- and nickel-iron sulphide melts. Molybdenum behaves only modestly in that way (Walker & Li, 2008; Righter et al., 2017). They both are known to be trace elements accompanying copper and nickel sulphide ores. No solubility data, however, are available for them in copper-rich sulphide mattes. Geochemical data on the behaviour of Ir and Mo deal mostly with low-iron silicate systems, e.g. basaltic melts, and high-sulphur sulphide solutions and mattes (Ertel et al., 2008; Fonseca et al., 2007). They also indicate that Ir and Mo dissolve in silicate melts primarily as oxides and not as electrically neutral metal species. Most geological data of iridium focus on high-sulphur systems of the monosulphide composition and typically Fe-Ni mattes where copper is a trace element (Fleet et al., 1996; Sattari et al., 2002). Direct solubility measurements for mattes and iron-lean silicates have also been made using pure Ir or an Ir alloy as the saturation phase (Borisov & Palme, 2000; O’Neill & Eggins, 2002; Makovicky & Karup-Møller, 1999; Ertel et al., 2008; Mungall & Brenan, 2014). A recent summary about the solubilities of HSE’s in iron- and sulphur free silicates is available in Laurenz (2012). The thermodynamics of molybdenum partitioning between oxides and Fe-S-O melts was studied by Mengason et al. (2011). Their results indicate strong accumulation in the iron-rich sulphide in reducing conditions (pO2 = 10-9.6 atm in Ni-NiO equilibrium at 1050°C). Molybdenum dissolves in iron-lean silicate melts as MoO3 species in oxygen pressures above the Fe-FeO equilibrium and as MoO2 in more reducing conditions (Farges et al., 2006; Righter et al., 2017).

Jan 1, 2019

By P. Espinoza, I. Yutronic, J. Olivares

"Compañía Minera Doña Inés de Collahuasi&apos;s (CMDIC) Concentrator Plant is located at 4300 meters above sea level, approximately 2000 kms north from Santiago, Chile. The concentrator has three grinding lines. Each one, Lines 1 and 2, have one SAG mill at the primary grinding stage followed by a secondary grinding and classification stage consisting of one ball mill, two hydrocyclone batteries and a sump with two pumps. Line 3 has one SAG mill (Gearless Mill Drive), followed by a secondary grinding and classification consisting two ball mills, four hydrocyclone batteries and a sump with four pumps. Average throughput for these three lines is 150 Ktons per day. Peak values of 180 ktons per day have been achieved.Since late 2008 and throughout 2009 and 2010, Operations and Automation areas developed an optimization program for the grinding process, considering the implementation of Model Predictive Controllers (MPC) for the three SAG mills, and later, extending MPC to the secondary grinding and classification stages. The implementation of a MPC solution was based on stability considerations (high variability of the SAG process, high interaction between sump level control and classification efficiency, etc), requirements for an automated and consistent operation, the need to maximize throughput under timevarying scenarios and, in the long term, optimization of grinding process considering Specific Energy Consumption, among other parameters. MPC solutions had proven control robustness and strong optimizing capabilities in terms of helping in discovering new operational points and so achieving all of the aforementioned goals.On the first stage of the program, MPC implementation considered identification of dynamical process control models based mainly on historical data, in order to know the impact of a group of Manipulated Variables over Controlled Variables. Also, the impact of measured Disturbance Variables was modeled in order to take into account the high impact and interaction of these variables over the processes. At the end of this stage, 4 controllers were successfully operating for the 3 SAG mills and the secondary grinding and classification process. In response to challenges made by the working group, the second stage of the development of control applications in the grinding process required to achieve a design and implementation of a solution capable of governing the milling process, in addition to stabilization and optimization of both processes (SAG milling and secondary grinding), to integrate from a point of view of process control and automation. Therefore, in the second stage, MPC performance was continuously monitored and optimized through advanced tuning, inclusion of more process models (with proper step tests), redefinition of specific optimization criteria and adjustment to new process needs.Finally, successful MPC implementation at Collahuasi has proved that fast development and deployment of process control solutions is possible and allows immediate process stability, higher throughput, specific energy consumption reduction, and successful product size control, among many others."

Jan 1, 2012