Search Documents

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By F. Mohamm

"Recent changes in regulations and scientific advances concerning selenium bioaccumulation have placed greater importance on non-biological treatment systems for selenium control. Mining wastewater contains hexavalent selenium (selenate) as the predominant aqueous species and possibly small amounts of tetravalent selenium (selenite). Non-biological removal of selenite is accomplished readily and cost effectively by ferric co-precipitation and adsorption using ferric oxyhydroxides sourced from ferric salts or iron anodes in electrocoagulation cells. Selenate on the other hand is difficult to remove. It is often incorrectly assumed that electrocoagulation is suitable for removing both selenite and selenate. Selenate removal efficiency by electrocoagulation is low and the amount of waste residue produced high. In contrast, BioteQ’s Selen-IX™ process removes selenate very efficiently and produces a much smaller amount of stable residue. The process combines selective ion exchange with electro-reduction of selenate in electrocells that physically resemble electrocoagulation cells but are designed and operated differently. This paper summarizes four years of pilot scale demonstration on a wide range of mine waters and discusses the key benefits and limitations of Selen-IX™. The pros and cons of combining ion exchange with electro-reduction in comparison to direct electro-reduction of selenate are also reviewed.INTRODUCTION Selenium in Mining and Mineral Processing Effluents Similar to sulphate and metals, selenium presence in mining and mineral processing wastewater originates from minerals contained in the mined deposits. Therefore, no organoselenium species are typically present in these kinds of waters and inorganic species including selenite (SeO32-), selenate (SeO42) and elemental selenium account for the majority, if not all, selenium present in these streams. Elemental selenium is not always present in mine water but is often contained in smelter wastewater. To comply with new environmental regulations, a successful water treatment plant must remove selenium from all these forms effectively and economically without generating by-products that are difficult to dispose of or manage. Elemental selenium can be dealt with using filtration or gravity separation in clarifiers often assisted by flocculants and/or coagulants. Mine impacted waters typically contain other forms of suspended solids which are removed from water in this way. Once the solids are removed, the selenium species that remain untreated are the dissolved forms. In mining waters this is mostly selenate with small fraction of selenite. In smelter wastewater, the majority could be selenite. It is well established that tetravalent selenium is readily removed from water by using ferric iron co-precipitation at pH > 4 (NAMC SWG, 2010). Ferric hydroxide/ferrihydrite solids act as the adsorbent for tetravalent selenium when it is in one of the ionic forms of biselenite or selenite. This treatment for tetravalent selenium is highly efficient. Therefore, tetravalent selenium removal is generally not an issue and is often easily incorporated into lime neutralization or unit operations such as electrocoagulation used for removing other metals present in mine impacted waters. Another option of dealing with tetravalent selenium is sulphide precipitation in acidic pH which produces SeS2 and can separate selenite from other metals and/or sludge produced at neutral to alkali pH."

Jan 1, 2017

By Lewis Martin

Whereas many researchers and mine engineers have conducted tests using different types of grout, grout ratios, and physical modifications of the cable to determine cable bolt load characteristics, few studies have been conducted on cables fitted with internal instruments. Those studies that have been done have concentrated on cable behavior averaged over significant cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed . This paper documents test results on these modified cable bolts. Three tests were conducted at SRL on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over significant cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable and thereby allow interpolation of maximum possible loads on a cable.

May 1, 2002

By G. Minhas, M. Pule, Y. Laffitte, M. c. McGurn, T. Tzanetakis, Peacey. J., R. Susilo

Titanium (Ti) metal production from titanium tetrachloride (TiCl4) using magnesium (Mg) as a reducing agent is the well-known Kroll process. A chloride route is used to avoid oxidation of the titanium sponge. The sponge is consolidated into ingots and can then be made into powder by melting and atomizing or by hydriding/dehydriding. Attempts at direct powder production have met with difficulties, including low Ti yield and the formation of very fine particles (particles between 25-100 µm are desired). This paper discusses two methods to produce Ti powder in a molten salt medium using magnesium powder as a starting material instead of a pool of molten magnesium. The first method is a direct reduction of gaseous TiCl4 injected in the melt with the magnesium powder in suspension in the molten salt. The second method is a two stage TiCl4 reduction reaction where recycled Ti was used to form titanium dichloride (TiCl2) in the first stage followed by addition of magnesium powder into molten salt in the second stage. A correlation between Ti yield and processing variables such as TiCl4 to Mg ratio, Mg particle size, TiCl2 concentration in the melt, and reaction temperature was studied. The Ti powder formed was also analyzed for particle size distribution. Despite challenges and difficulties encountered, this paper shows some promising results which could provide guidance to others working on direct Ti powder production.

Jan 1, 2015

By D. Warkentin, T. Yeomans, R. Tavakoli, A. Nacu

"One of the most successful commercial methods of extracting gold from ores involves solubilizing gold as a gold cyanide complex, followed by adsorption of the complex onto activated carbon. The gold cyanide is subsequently eluted from the carbon to produce a concentrated gold solution suitable for electrowinning to recover the precious metals. Stripped carbon is treated in a kiln under a flowing steam atmosphere to reactivate its surface, allowing it to be reused. The aim of this study was to investigate the gold elution using a mixture of sodium hydroxide and isopropyl alcohol in both batch and continuous tests, with the eluates being electrowon on carbon foam cathodes. The effects of various factors, including alcohol content and sodium cyanide addition were studied. The addition of alcohol considerably improved gold elution kinetics, while the presence of sodium cyanide did not have a significant impact on either elution efficiency or kinetics. In all cases, efficient electrolysis was shown to be an important factor in maintaining effective carbon circuit operation.INTRODUCTION Gold dissolved as Au(CN)2- complex during cyanidation is recovered either by cementation with zinc powder, also known as the Merrill-Crowe process, or by adsorption into activated carbon through Carbon-in-Pulp (CIP) or Carbon-in-Leach (CIL) processes. Activated carbon loaded with gold is then eluted and gold is subsequently recovered by electrochemical methods. Conventional elution processes such as atmospheric and pressurized Zadra processes, involve stripping with a cyanide (0.1–0.2% NaCN) and sodium hydroxide solution (1–2% NaOH) at high temperature (90–140°C) over long elution times of 8 to 72 hours. In the Anglo American Research Laboratories (ARL) elution process, the acid-washed loaded carbon is pretreated with a strong sodium cyanide and sodium hydroxide solution (1–5% NaCN and 1–2% NaOH), followed by elution with water at 110–130°C. Solvent-assisted elution processes have also been reported, such methods use varying concentrations of alcohols (methanol, ethanol and isopropanol), ketones, or glycols to enhance atmospheric elutions at temperatures up to 95°C (Muir et al., 1985; Ubaldini et al., 2006; Espiell et al., 2008; Soleimani & Kaghazchi, 2008). The present work investigates the efficiency of isopropanol in the gold elution process, as well as the methodology of evaluating gold stripping processes in the lab setting"

Jan 1, 2017

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities for the nickel industry, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTION The process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic. A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities. These suggestions are particularly applicable to the nickel industry, where the majority of our firm’s prior hydrometallurgical experience was obtained. This paper is an update to an earlier publication (Martin, 2004), offering an opportunity for a new generation of metallurgists and engineers to learn the specialist requirements of pilot- and demonstration-scale plant design, which are key functions in the development and commercialization of new processes."

Jan 1, 2017

By Krishna Parameswaran

In this paper, we attempt to answer an often asked question, how can metal mining be compatible with the principles of sustainable development. Starting with the classic Brundtland Commission definition of sustainable development as "development that meets the needs of the present without compromising the ability of future generations to meet their own needs," we make the case that mining is or should be sustainable, using examples of sustainable practices at ASARCO LLC, an integrated U.S primary copper producer. These examples cover the entire mining cycle starting with exploration, mining, beneficiation, smelting, refining, closure and post-closure and post-mining land use. It is hoped that the presentation will challenge the mining industry to even greater innovation as future mineral development projects are planned.

Jan 1, 2015

By Eric Barnard, Andreas Nashitati, John Tero, Guy Deschênes, Setta Mbalamba, John Rajala

The Otjikoto Mine, owned at 90% by B2Gold Corporation, is located 300 km north of Namibia’s capital city of Windhoek. The reserves from the open pit mine, estimated at 25.9 million tons with an average grade of 1.28 g/t Au, contain gangue minerals, pyrite and pyrrhotite, and have an estimated 10 year mine life. The feasibility study included an optimisation of gold leaching using CSTR for the original design. The results of the test work were used to establish the design criteria. Gravity tails from three composites (drill cores), representing the major ore types, were used. The XR3 sample (gravity tails) contained 0.32 g/t Au, while the XR2 and XR1 gravity tails samples (used for variability) contained, respectively, 0.30 g/t Au, and 0.47 g/t Au. The optimum leaching conditions were: a pre-treatment of 7 h at pH 10.5 with 100 g/t lead nitrate, DO > 5 ppm followed by cyanidation at 300 ppm NaCN, pH 10.0, DO > 5 ppm for 48 h. The gold extraction was 91.5% (97.2% overall extraction gravity/leach) and the cyanide addition was 0.57 kg/t NaCN. Increasing the DO to 16 ppm did not show any economic benefits. No pre-treatment or a 4-h pre-treatment reduced the gold leaching kinetics. The XR2 and XR1 gravity tails samples had gold extractions of 92.9% and 92.3%, respectively. At the plant scale, an 11 h pre-treatment is used followed by 42 h cyanidation with 250 ppm NaCN and an average DO of 8 ppm and 230 g/t lead nitrate in 2016. The cyanide addition was 0.49 kg/t NaCN. The commercial operation started on February 28th, 2015. The overall gold recovery and production were 98.4% and 145,696 ounces for 2015 and 98.1% and 166,286 ounces for 2016. It was found that retention times, gold content of leach residues and cyanide addition are comparable for the lab and the plant. Details of the Otjikoto process flowsheet are discussed in this paper along with the results of the lab leach optimisation test program and the plant leach circuit performance and improvements.

Jan 1, 2017

By R. Luchese de Moraes, J. A. Matthews, C. Feliciano Bruzual

The role of biomass char in blast furnaces has been re-examined by scientists worldwide, as a feasible option to reduce the carbon intensity of ironmaking. This contribution makes a technical and economic analysis of the ferro gusa industry in Brazil, with the last 172 charcoal-Blast Furnaces operating in the world. A key strategic question is presented: what is the current status and future prospects of biomass use in Blast Furnaces? Findings provide significant implications to metallurgists: while ferro gusa from charcoal is regarded as carbon neutral iron with low impurities, there are limiting factors that hinder the further proliferation of charcoal-BFs: biomass generation requires vast extensions of arable land and aggregates have low production capacity. Additionally, most of the charcoal is presently generated in beehive kilns with low yields. These elements combined make charcoal-hot metal expensive in price. With respect to the future prospects of biomass, the injection of small biochar particles through the PCI rigs in BFs (here coined Bio-PCI) and iron ore sintering may offer a practical alternative to significantly reduce the CO2 emissions in the ironmaking process.

Jan 1, 2015

By G. J. S. Govett

World mineral production is dominated by six countries - the U.S., the U.S.S.R , Canada, South Africa, Australia and China - which also hold most of the reserves of the world?s minerals. For the developed and centrally planned countries, there is a strong positive correlation between the mineral production of a country and its land area: there is no correlation between mineral production and land area for the less developed countries. These facts imply that, after taking due account of geological controlling factors, a country may expect to produce minerals in approximate proportion to its land are a provided that political, economic, and historical factors are conducive to mineral exploration and mining. Contrary to popular political belief in many parts of the world, the developed countries are the major source of mineral imports for the industrialized countries. Moreover, exports of ores and minerals account for a relatively small par t of world trade, and are an important factor in the export picture of only a few of the less-developed countries. The looming resource confrontation between the developed and the less-developed countries is based largely on the false premise that the industrialized countries of the world are minerals-poor and owe their wealth to cheap minerals from the less-developed countries. The data presented refute this. Geological controls are relatively minor in the present distribution of world mineral production; political and economic factors are dominant. It is argued that an expansion of world trade in minerals - based on increased exploration and new forms of finance for mining ventures - rather than cartels, price-fixing and trade restrictions is by far the preferable solution to the problem of redressing the legitimate grievances of the poor countries of the world.

Jan 1, 1977

By Gordon W. Hines

This paper, dealing with network planning in an industrial complex, discusses the type and size of project that can be handled on a manual basis. After a review of the fundamentals of network planning, and specifically of the Critical Path Method, the author analyses several different types of projects, each with its own characteristics. Some can be handled in conjunction with a computer, but others can be dealt with equally well without one. Among the projects discussed are a blast furnace reline, the installation of a billet mill flying shear, and routine maintenance-type operations.

Jan 1, 1967

By David Rahal, Des Erasmus, Ken Major

"Over the past twenty years there has been an increased emphasis on fine grinding in the minerals industry. This spurred the development of a range of new fine grinding equipment in the 1990s. At that time, the Knelson-Deswik mill was developed in South Africa for the pigments industry.Knelson Milling Solutions currently offers a wide range of laboratory, pilot and production scale mills. These mills bridge the gap between traditional low speed vertical mills and the high speed horizontal mills (tip speed < 3 and > 15 m/s respectively). They are designed to run at tip speeds between 10 and 12 m/s and are capable of operating with very dense grinding media. The result is a power intensity that is higher than the low speed mills and overlaps that of the high speed mills. This allows the mill to be customized for a wide range of grinding applications.A case study at Aquarius Platinum’s Kroondal Mine shows that the Knelson-Deswik technology can produce a consistent product size despite feed variations. It also shows that the throughput was proportional to the slurry density at Kroondal. The case study identified increasing the slurry density as a process change that can increase throughput and reduce the specific energy consumption.INTRODUCTIONThe increasing complexity and finer grain sizes of modern ore bodies have increased the importance of effective mineral liberation in obtaining acceptable grades and recoveries (Jankovic, Valery and La Rosa, 2003; Lichter and Davey, 2006; Napier-Munn, Morell, Morrison and Kojovic, 1996). This trend has increased the significance of fine grinding technology because the input energy increases exponentially as the required product size decreases from 100 to 10 microns (Gao and Weller, 1993a).The US Department of Energy recently provided the context for the potential energy savings in the US Mining Industry (BCS, 2007). They reported that grinding consumes approximately 494 TBtu/year. This was over double the consumption of the second highest equipment category, diesel materials handling systems (211 TBtu/yr). The proportion of grinding energy allocated to fine grinding can only be expected to increase as finer ore deposits are mined. It is therefore critical that fine grinding efficiency continue to improve through the selection of appropriate equipment and the development of best practices for existing applications."

Jan 1, 2011

By Mingxia Liu, Hao Li, Qi Liu

"Laboratory batch flotation tests were carried out on fine (-20 µm) hematite to investigate the non-polar oil’s influences when sodium oleate, octyl hydroxamic acid, or oleyl hydroxamic acid were used as a collector. Batch flotation tests were performed with artificial mixed minerals (hematite:quartz = 1:1) under natural pH condition and kerosene was utilized as the model oil. The experimental results showed that kerosene emulsion behaved differently when used in conjunction with the three collectors. Kerosene helped improve the flotation when sodium oleate or oleyl hydroxamic acid was used as a collector. Nevertheless, it reduced concentrate weight yield, grade and recovery to a noticeable extent when octyl hydroxamic acid was used as a collector, especially at low dosages. In addition, single hematite batch flotation kinetics tests coupled with water recovery measurement were carried out to study the role of kerosene at different collector dosages. It was observed that water drainage and the resulting froth destabilization by kerosene was dominant at low collector dosages, especially in the flotation using octyl hydroxamic acid. At higher collector dosages, the water drainage and froth destabilization effect by kerosene was possibly counter-balanced by the higher hematite hydrophobicity and bubble surface tension gradient, which led to more stable froth layer.INTRODUCTION The minerals industry is facing a steady decline in ore grade, compounded by increasing complexity of mineral dissemination. As a result, the ore has to be ground sufficiently fine to have a suitable degree of mineral liberation, which produces large percentages of fine and ultrafine particles outside of optimal size range for ore dressing. Due to the unique characteristics of fine particles, i.e., small mass, high specific surface area, and problems such as increased solubility of complex minerals (Finkelstein, 1997; Finkelstein & Allison, 1976; Fornasiero & Ralston, 2005), high reagent consumption, fast surface oxidation in the case of sulfides (Collins & Read, 1971; Klassen & Mokrousov, 1963), severe particle entrainment (Subrahmanyam & Forssberg, 1988; Warren, 1984), low flotation rates (Glembotsky, 1953; Philippoff, 1952; Ye & Miller, 1988), slime coating (T. K. Mitchell et al., 2005; Parsonage, 1984), etc., flotation performance of these finely ground ores is very poor in terms of low concentrate grade and recovery."

Jan 1, 2017

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

The present work aims at some process modifications in specified metallurgical processes, wherein CO2 can be used successfully as an oxidant for decarburization in steelmaking and applied in some non-ferrous metals production processes. During the decarburization of Cr-containing high alloyed steels, the present researchers investigated the possible use of CO2 instead of Ar-O2 mixture and could successfully decarburize the steel melt without significant loss of alloyed Cr to the slag phase. A mathematical model was developed based on the bubble formation accompanying the chemical reaction: C(molten steel)+ CO2(gas)= 2 CO(gas). The model predictions were tested by laboratory scale (1 kg) experiments carried out in an induction furnace and very good agreement between the model predictions and experimental results were observed. A national project has been sanctioned in China for the implementation of CO2 in decarburization of ferroalloys as well enable the addition of pig iron in the electric arc furnace process when the scrap supply is limited. New processes have been developed for the utilization of CO2 in the case of non-ferrous processes. A novel method of treatment of Al dross by leaching with water and capturing the evolved NH3(formed by the hydrolysis of AlN) has shown very promising results.

Jan 1, 2015

By Frederic M. Langevin

?? Introduction ?? LaRonde ?? History of Seismicity and Rockbursting ?? November 27th 2002 Rockburst ?? April 1st 2006 Rockburst ?? December 11th 2006 & January 11th 2007 Rockbursts ?? Seismic Risk Management Plan ?? Conclusions ?? Located in Northwestern Quebec (Can.) ?? In operation since 1988 ?? Reserves at Shafts #1 and #2 depleted ?? Production now comes entirely from Penna Shaft ?? Deepest single-lift shaft in the western hemisphere (2240 metres) ?? 7300+ tonnes per day ?? 2007 Reserves (proven & probable): ?? By-products: Ag, Cu, Zn ?? Sinking #4 Shaft (LaRonde II winze)

Feb 1, 2008

By Paul Voigt, Mike Hourn, Glenn Stieper

Sable Zinc Kabwe Limited ("Sable") is a base metal processing plant, two kilometres south of Kabwe Town in Central Province, Zambia. The region has a rich history in mining and minerals production, being a major lead and zinc producer from the 1900s up to the mid-1990s. In 2006, a copper plant was built at the Sable processing site to treat third-party copper and cobalt oxide ores and concentrates. The oxide leaching plant included whole ore leaching, solvent extraction and production of 8,000 tpa LME Grade A copper cathode. The plant was placed on care and maintenance in 2014, and Glencore Plc ("Glencore") took the opportunity to convert the plant using a minimal budget, to an Albion Process™ plant to treat local refractory copper concentrates unsuitable or uneconomic for smelting. The Albion Process™ plant comprises an M100 IsaMill™ operating in acidic conditions such that raffinate from the downstream process is recycled back to slurry the concentrate delivered to site thus maximising copper tenor in solution and reducing water consumption. The finely ground concentrate feeds an oxidative leaching plant using the existing stainless steel oxide leach reactors converted to Albion Process™ duty by fitting HyperSparge™ supersonic oxygen injectors and gas dispersing agitators. The leached slurry is then directed to the existing solid/liquid separation equipment, and the PLS is then sent to the existing SX/EW plant. The plant also allows for cobalt recovery from the raffinate. The plant was designed based on testwork on regional copper concentrates. The plant was designed to toll treat a range of concentrates, and so the design was flexible With the flexibility of the Albion Process™ being one of its distinct advantages, the plant was ideally suited for tolling regional concentrates. The plant was commissioned and ramped up in six weeks using low-grade Zambian copper concentrate, and produced exclusively LME Grade A copper with over 99% leach recovery in the Albion circuit. INTRODUCTION The Sable Zinc Kabwe Limited ("Sable") process plant is located 2 km south of Kabwe town and 140km north of Lusaka in Central Province, Zambia. In 1902, rich deposits of zinc and lead were discovered with mines and processing plants operating in and around the town until mid-1994. In 2000, the Kabwe Mine tailings dams were sold to Sable, a newly established company, as part of a purchase deal for other plots and facilities. Up until 2004, Sable produced zinc cathodes in an SX/EW plant treating wash plant tailing material. In 2004, Sable was acquired by the South African mining company Metorex Limited ("Metorex"), and in 2006 a copper/cobalt SX/EW plant was built to produce copper cathode from malachite ore supplied from the Democratic Republic of Congo. In 2011, Jinchuan Group International Resources Co. Ltd acquired Metorex and Sable was in turn sold to a subsidiary of Glencore Plc ("Glencore").

Jan 1, 2019

By Jim Sadowski, Steve Stewart, Bob McMurdy, Martin Nevens

"Mohawk Garnet has been operating a small pilot plant near Sudbury, Ontario for several years attempting to produce commercially viable garnet. The challenges of operating a pilot scale mining, processing, and product handling operation as a full time plant have led Mohawk Garnet to seek a better way. In co-operation with Mohawk Garnet, Outotec (USA) Inc. has taken on the technical and design challenges of increasing garnet product from twenty tonnes per day to two hundred tonnes per day.Outotec performed a comprehensive test and flowsheet development program applying Outotec’s density separators, spirals, flotation, and other technologies to design a successful process for the separation and recovery of the valuable garnet for Mohawk.This paper explores the test program, the process flowsheet development work, plant design and preliminary engineering of a new garnet processing. The various technical challenges, process technologies involved, and design concepts will be discussed.INTRODUCTIONMohawk garnet has been operating a small-scale garnet mine and process plant in Wahnapitae, Ontario near Sudbury.The current operation was intended to be a pilot plant and so only produces 20-25 tonnes of garnet concentrate per day. The garnet is bagged and sold for use as abrasive. The process is inefficient with low yields, poor material handling and very high cost per tonne. Mohawk garnet approached Outotec to help them improve their garnet process and transform themselves into a larger scale and more efficient operation."

Jan 1, 2010

By Yaw Boadi, Andrew McCallum, Sandy Gray, Yavuz Atasoy, Peter Wemyss

"Various full-scale test programs and installations of the InLine Pressure Jig (IPJ) have provided evidence that pre-concentration of the difficult to leach sulphide mineral through gravity can provide significant increases in economic recoveries. The continuous gravity concentrates are intensively treated either by re-grinding or Intensive Cyanidation. Data from various mine sites worldwide is presented. Treatment of complex ore bodies with this low cost methodology may render previously uneconomic ore bodies financially viable and assist in the recovery profile of transitional ore.INTRODUCTIONThe use of gravity is made extremely attractive in complex ore situations due to the low cost of operation, typically a few cents per ton operating cost and lack of chemicals.Gold mines which suffer from poor recovery due to complex mineralogy such as Stibnite, Arsenic, Carbon, Telluride, Silver and other pacifying agents such as Iron, which can form coatings, can all benefit from the process proposed in this paper. The key issue is not overall recovery as much as one of economic recovery. The key to this is maximised recovery at the lowest possible capital and operating cost. Other options such as flotation are reviewed but are not seen in many instances to be the panacea due to issues discussed in the paper. The use of the InLine Pressure Jig in the re-circulating load of the milling circuit is a cost effective means of recovering a sulphide/gold concentrate containing the complex mineral assemblages which require re-grinding and intensive leaching for optimised gold recovery.The benefits of Jig Assisted Grinding (JAG) are many and the challenge over the past years has been developing, understanding, implementing and evaluating the benefits of various flowsheet models. This has involved the reconciliation of results in plant scale trials back to the original laboratory test program. The following paper outlines the insights gained in this area through extensive work carried out by many people across both laboratories and plant sites in Australia and overseas. The examples in this paper are some of the work carried out on a few selected sites but similar work has been carried out on other sites such as Penjom, Granny Smith and Agnew. This work has eventuated in several installations which we believe have great importance in the future of the gold processing industry. They will lead the way forward to the modern all-gravity plants of the future.Compared to flotation, for the recovery of sulphides, gravity is a simple option. The simplicity generally translates to low capital and operating cost."

Jan 1, 2004

By Charles "Chick" Rodgers

"The Key Lake uranium mine is the largest single uranium producer in the world. It is owned 2/3 by Cameco Corporation and 1/3 by Uranerz Exploration and Mining. Cameco is the operator. Current production is fourteen million pounds per year of uranium oxide (U308).The mine's location is 570 kilometres north of Saskatoon on the southern edge of the Athabasca Basin approximately at latitude 57° 11 'north and longitude 105° 34' west. Access to the mine is by an all-weather road and a private airstrip.The mill was commissioned in 1983. A molybdenum plant was constructed in 1989 in response to increasing molybdenum content in the yellowcake or final product. Early test work had showed that the first ore body to be mined, the Gaertner deposit, would present few problems with regards to molybdenum in the product. However, the test work also showed that the higher molybdenum content of the Deilmann ore, the second Key Lake orebody to be mined, would result in increased molybdenum concentrations. Without the molybdenum plant, penalties would become excessive and some product might not accepted by the refineries.This paper will describe the current Key Lake mill process with emphasis on the molybdenum solvent extraction process. It will cover the chemistry of the process, process development in the mid 1980's, and current operating practices.The Key Lake milling process consists of five individual plants, crushing and grinding, leaching -counter current decantation (CCD), solvent extraction, yellowcake/crystallization and bulk neutralization (Figure 1. Simplified Mill Flowsheet). A detailed mill flowsheet can be found in the appendix."

Jan 1, 1996

By Iina Vaajamo, Jani Jansson, Lauri Pesonen

In pyrometallurgical operations, structural integrity of a high temperature furnace plays a crucial role in the overall safety, profitability and ecological footprint of the plant. Furnace integrity is related to how reliable a furnace is and it can be compromised, for example, by having poor operating and maintenance practices, an inefficient cooling system and flaws in the overall furnace design. These flaws and poor practices might lead to unexpected shutdowns, production losses, increased emissions, or worse. This paper presents the main factors to consider when engineering a furnace and developing its operating practices, while ensuring safe and reliable operations without compromising process efficiency and quality of the final products. In this respect, Outotec’s solutions for the cooling system and for automation systems like PROSCON, Process Advisor, Sentinel and our Smelting Information Management System, are also introduced.

Jan 1, 2015