Search Documents

By A. Haldar

This study focuses on the flow characteristics of hypereutectic Al-Si alloys in thin sections. The pattern assembly consisted of spiral horizontal patterns, 6.25 mm (0.25 inch) and 12.50 mm (0.50 inch) in thickness with a common sprue. Al-Si alloys with silicon levels of 14%, 18% and 22% were poured with superheats of 60°C, 115°C and 170°C. It was observed that metal fluidity (in terms of flow length and metal velocity) increased with increase in silicon levels and superheat for both section thicknesses. It was also observed that, for a section thickness of 6.25 mm (0.25 inch), silicon level had more pronounced effect on the metal fluidity. For 12.50 mm (0.50 inch) thickness, both silicon level and superheat affected the metal fluidity. The surface hardness of the castings increased with an increase in silicon level of the alloys at the gate and the flow tip. Detailed study of the flow tip was also carried out with a view to understanding the effect of silicon level and superheat on undulated flow length, surface hardness and microstructure.

Jan 1, 2007

By Baisheng Nie, Longlong Yang, Tao Yang, Wenjie Jia

"Gas adsorption in coal is an exothermic and physical process. Temperature might change during the dynamical process. In order to get the temperature variation of gas adsorption process, the experiment system which can test the temperature variation and analyze the thermal effect was established. Gas adsorption experiments under different conditions were done by using the test system. The results show that temperature increases during the adsorption process. It is an exothermic reaction process. Also, the temperature variation and the variation gradient increase with the increasing of equilibrium pressure. The temperature variation value is smaller if the experiment temperature is higher. The paper will provide basic experimental data for explaining gas adsorption mechanism better.INTRODUCTIONChina is the largest coal producer in the world while it also has the most serious coal mine disasters. According to the statistics, there are nearly a thousand coal mines in China including more than 110 the key state-owned mines risking to happen coal and gas outburst. Hundreds of coal and gas outburst occur each year which often causes serious casualties and economic losses (State Administration of Work Safety, 2007). With the continuing exploitation of the coal resources, the depth of the Chinese coal mines increases about 100 meters every year which causes the situation of gas accident becoming more and more serious (Xie et al., 2006).At present, the real mechanism of gas adsorption, desorption and the diffusion process in coal and the influence factor of it are not so clear. And because of the limit of prediction method and the technological level caused gas accident prevention theory and technology not so valid."

Jan 1, 2015

By D. A. Garland, A. D. Jackson

"Alanx ceramic/metal composites are proprietary products developed by Lanxide Corporation who joined with Alcan to form Alanx Products L.P. in 1988. Alanx ceramic/metal composites are composed of silicon carbide in a combined alumina and metallic aluminum matrix. In laboratory slurry wear tests conducted by Alanx ceramic/metal composites have shown to perform well against other wear resistant materials. At the Kidd Creek Concentrator Alanx CG896 ceramic/metal composite was tested in two pumping applications, the primary cyclone feed pumps and the filter feed pumps. In both instances the wear rates of the parts made of Alanx CG896 were far less than the gum rubber parts traditionally used. As of year to date September 1992 the unit cost to repair primary cyclone pump parts has dropped 58% from 1991 figures. For the filter feed pumps the unit cost to maintain the pumps has dropped by 33% as compared to 1990 figures. The total savings represented by implementation of Alanx wear parts, based on projected year end unit costs for 1992, as compared to 1991 costs for primary cyclone feed pumps and 1990 figures for filter feed pumps, is $166,753. INTRODUCTIONAt the Kidd Creek Concentrator the cost to maintain the primary cyclone feed pumps and the filter feed pumps was a constant concern. Rubber wear part consumption was quite high and the manpower required was considerable. For 1991 the total cost to maintain five primary cyclone pumps was $244,062. The cost to maintain the filter feed pumps in 1990 was $72,076. A wear material was needed that would increase the time between repairs and that would increase the reliability of these pumps between scheduled shut downs."

Jan 1, 1993

By Robert B. Parsons

"For the fourth time in five years, residents of northern Canada have seen a change in the tax treatment of housing and travel costs. The latest changes announced in December 1990 by the Minister of Finance are to become effective in 1991. When will the tinkering stop?IntroductionFor man y years prior to 1987, certain travel and housing allowances received by employees in remote areas were generally considered by Revenue Canada to be tax-free, even though some observers suspected that such generous treatment was contrary to the provisions of the tax legislation. In the mid-eighties, Revenue Canada decided to reconsider the tax treatment of the mining industry's long standing practice of providing housing and travel assistance to these employees. The tax- free treatment was continued by virtue of annual remission orders, but only pending the enactment of legislation which would tackle the issue head-on and layout the rules in black and white to be seen by all. The sequence of events since then may be chronicled as follows:February 26, 1986-Finance Minister Wilson's budget present s the framework for the future tax treatment of travel and housing benefits provided to residents in remote regions of Canada.December 22, 1986-The Minister of Finance announces detailed rules to fill in the earlier announced framework.January 1, 1987-The new tax rules come into effect.April 29, 1988-The Minister of Finance announces the establishment of a Task Force to examine the existing criteria for determining the eligibility of residents of northern and isolated areas for tax benefits.October 27, 1989-The Task Force presents its report.December 7, 1990-Finance Minister Wilson announces a new system of tax benefits for residents of Canada's northern and isolatedregions.January 1, 1991-The new rules become effective."

Jan 1, 1991

By X. Cao, X. -G. Chen, K. Liu

As is well known, the standard Al-Cu 206 cast alloys have extremely low iron contents, usually less than 0.15 wt. %. Recently it is found that the iron contents of the 206 cast alloys can be extended up to 0.5 wt. % through the precise control of the iron-rich intermetallic phases. In the present work, the tensile fracture surfaces of the 206 cast alloys with various iron contents are systematically analyzed to understand the failure mechanisms. Results show that higher iron contents can reduce the tensile properties (especially the ductility) of the alloys mainly due to the increasing volume percent and size of the iron-rich intermetallics. Tensile failure mainly occurs at the iron-rich intermetallics/matrix interfaces for the platelet ß-Fe, but by the self-disassociation for the Chinese script a-Fe and Alm(FeMn). Cracking is easier to initiate and propagate along the longitudinal axis of the platelet intermetallics, but it can be deflected along the branches/arms of the Chinese script iron-rich phases, making the alloy more resistant to the propagation of the cracks, and thus the Chinese script iron-rich intermetallics are less harmful than platelet ß-Fe. In addition, it was also found that the Chinese script a-Fe has even a less damaging effect compared to the Chinese script Alm(FeMn) due to the relatively small size and compact morphology.

Jan 1, 2014

By Patrick J. Williams

Outline -An Australian View On: ?IOCG defining features and occurrence ?Variable exploration characteristics ?Extracting value (gold metallurgy) ?Recent exploration experience(case study)

Apr 1, 2005

Agenda ?Trends in Wireless Technology ?Success and Opportunities ?Improving plants efficiency ?Improving plants reliability ?Improving plants safety and security ?Wireless Ecosystem ?Lessons Learnt / Recommendations Why Wireless? ?Lower cost (no wiring cost) ?Flexibility (no wire) ?Standards-compliant wireless devices major factor enabling growth:?Standard WLAN (IEEE 802.11)?Wireless field I/Os (IEEE 802.11, ISA100.11 and WirelessHART) ??Wireless adoption will become a milestone that will rival the introduction of Fieldbus and the distributed control system (DCS) in its importance.? ARC Advisory Group

May 1, 2009

By Marc Tardif

"The way alarm information is provided to an operator can make a huge difference in the minutes following an upset. Process alarms are often looked at as a way to help avoid catastrophic failure and serious accidents. But knowing that mineral processing is so energy consuming and that raw material is not consistent, all small upsets should also be seen as a catastrophe because they can have significant impact on product cost and quality.This paper will demonstrate how it is possible to use data from process alarms to provide operators with real time, value added information that will help them take the right decision at the right time and in turn, reduce unplanned downtime by 20 to 80% and incidents by up to 50% (number and cost),and optimize energy and capacity usage.In the era of Big Data, living in a world where we are submerged with information, one of the biggest challenges is to find the right information at the right time.Alarm rationalization projects will often focus on alarm quantity, but alarm quality is also very important. It is possible, by following a simple 6-step process to turn “alarms” into truly valuable information for operators. Based on known standards (ANSI/ISA 18.2 and EEMUA 191), this process will capture the knowledge of the best and most experienced operators and process engineers, and make it readily available to everyone, right on time, when it matters the most.INTRODUCTIONWhen spending some time in a modern control room, it is easy to notice the huge quantity of information that is available to the operator. Modern operation stations feature multiple screens with HD capability. These screens display information like process display, history trends, alarms and events list, maps with geo-located information, images from live cameras, etc. However, it is harder to assess whether all this information is really helping operators: Is all the information relevant? Are process screens overcrowded? Is the information easy to understand? Does the operator know what to do with all the information? Are there too many alarms?"

Jan 1, 2016

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By Franc R. Joubin, Donald H. James

"The Algoma (or Blind River) uranium district is centred in an area of some 600 square miles on the north shore of Lake Huron, about half way between Sudbury and Sault Ste. Marie, Ontario (Figure 1). Its favourable location, adjoining the main provincial highway and Canadian Pacific Railway line which follow the lake shore, has contributed greatly to its rapid development.By Canadian standards, the district has long attracted geological attention, beginning with the discovery of the Bruce mine in 1846. It has been repeatedly prospected at intervals since then, chiefly for copper and nickel but also for lead, zinc, cobalt, silver, iron, and gold. Numerous discoveries have prompted the suggestion by Yates (13) and others that one metal-logenic province embraces the entire mineralized area from Michigan through Sudbury and Cobalt.Geological mapping was initiated by Murray in 1847, and the area attracted much interest as the type locality of the Huronian, the correlation and stratigraphic position of which are still not entirely agreed on. Subsequent contributors to the geological literature of the area have been very numerous, and the bibliography at the end of this paper includes only some of the more modern reports.The history of uranium in this part of Ontario also dates from 1847, when J. L. LeConte identified as uranium-bearing a pitchblende-like mineral which he named ""coracite"". The specimens came from Theano Point, north of Sault Ste. Marie. In 1948 a search for the source of these specimens led to the discovery of the Camray uranium field. Occurrences in this field consist of numerous small and locally rich pitchblende-bearing fractures, within or along the contacts of diabase dykes cutting Archaean granite and gneiss.None of the showings explored proved large enough to justify production, but they stimulated prospecting of adjoining areas and thus led to the Algoma discoveries.The first find of radioactive conglomerate in place was made in 1949 in Long township, and it was partially staked as the Fisher-Audette-Breton property. Rusty, overgrown rock-cuts indicated that the pyrite-bearing conglomerate had been investigated years before, probably during searches for base metals and gold. Examinations were made at this time by a number of geologists, including the senior author. In spite of high radioactivity, sampling returned only negligible uranium. The claims were allowed to lapse and the showings reverted to obscurity."

Jan 1, 1949

By Jae-Chun Lee, Sadia Ilyas

We investigate the technical feasibility of bioleaching of metals from low grade sulphidic ore. Experiments were conducted with an adapted consortium of Sulfobacillus thermosulfidooxidans and Thermoplasm acidophilum in batch bioreactors (1.5 L), small columns (10 kg ore load, 8 % S0 sludge) and large columns (80 kg ore load, 12 % S0 sludge). Approximately 83 % Ni, 85 % Cu, 55 % Fe and 81 % Zn was leached out in batch mode while 93 % Ni, 89 % Zn, 81 % Cu and 65 % Fe was leached out in column reactors. Bioleaching potential improved by acid pre-leaching, adaptation of microbial consortium and periodic bleeding of effluents.

Jan 1, 2014

By J. C. Li, Y. Zou, L. He

"The effect of rock joints is significant in characterizing dynamic behaviors of discontinuous rock masses. To reveal the relation between the transmission coefficient and the contact situation of the joint surface, an experimental study on stress wave propagation across an artificial rock joint was carried out using a modified Split Hopkinson Pressure Bar (SHPB) apparatus. All the bars and specimens were norite cored from the same site, and one surface of the specimen which contacted to the transmitted bar was sawn with a number of notches to simulate the artificial rough joint. According to a wave separation method, two strain gauges were mounted on each pressure bar at a specific spacing, then the incident, reflected and transmitted waves across the joints were obtained from the test data. It was found that the contact situation of the rock joint surface makes a different on the wave propagation. Finally comparisons of the transmission coefficients with different contact area ratios and different joint thicknesses were made respectively. The results show the effects of contact area ratio and thickness of joints on wave transmission.INTRODUCTIONJoints affect the dynamic mechanical behaviors of the rock masses significantly. When propagates across the rock masses, wave usually attenuates in amplitude and frequency due to the presence of the joint as a discontinuous interface in the rock masses. Rock joints are the main factor that affects the behaviors and properties of rock masses. Many researchers have focused on the mechanical properties of rock joints under quasi-static conditions. Nowadays, the effect of joint dynamic properties on wave propagation across rock masses is gradually taken into account in theoretical and numerical studies.The effective contact area, joint roughness, and properties of the asperities and filling materials have been found to influence the normal stiffness of joints (Bandis et al. 1983). As suggested by the International Society for Rock Mechanics (ISRM), the roughness of the discontinuities can be generally characterized by large-scale “waviness” and small-scale “unevenness” (Brown 1981). Many researchers focused on the roughness of rock joints that affects the mechanical properties of rock masses and wave propagation. For example, Brown and Scholz (1985, 1986) presented theoretically and verified experimentally a closure model of contact between two random nominally flat elastic surfaces, which showed that the joint closure property depended both on the surface topography and material properties. Pyrak-Nolte et al. (1997) presented the quantitative aperture data for three-dimensional interconnected fracture networks, which were imbedded in intact opaque rock samples several centimeters in length, using x-ray computerized tomographic (CT) imaging. Fardin et al. (2001) systematically investigated the effect of scale on the surface roughness of rock joints and concluded that samples should be equal to or larger than the stationary limit for surface roughness to be accurately characterized on a laboratory scale or in the field. Zhao et al. (2006) conducted excellent ultrasonic tests across intact cement mortar specimens, singlefracture specimens, and two-fracture specimens."

Jan 1, 2015

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By A. L. Mackie

Mine water from base metal mines is generally characterized as having high concentrations of heavy metals and low pH, resulting in the need for treatment prior to discharge to receiving waters. In this study, two high-rate clarification processes were evaluated at bench-scale: the high density sludge (HDS) process and sand-ballasted flocculation. High-rate clarification processes generate larger, denser flocs which settle more quickly than those formed in conventional flocculation processes. The HDS process uses recirculated sludge in order to seed floc formation, whereas ballasted flocculation uses microsand. Both of these high-rate processes require the addition of quicklime or hydrated lime to increase pH and allow for the formation of insoluble metal hydroxides, which can then be removed in the clarification stage. Previous research has shown that cement kiln dust (CKD) can effectively replace quicklime in conventional sedimentation processes for metals and acidity reduction to meet discharge guidelines (Mackie & Walsh 2012). CKD is an alkaline by-product of cement manufacture that has fine particle sizes and varying free lime concentrations depending on the manufacturing process. The lower solubility (i.e., free lime content) of CKD requires larger doses of material to be added to reach treatment pH targets for metals precipitation. The purpose of this study was to evaluate the treatment efficacy of high-rate clarification processes for mine water treatment, compared with conventional sedimentation, at bench-scale with conventional (i.e., lime) and novel (i.e., CKD) pH adjustment additives. Results of the study showed that all treatment processes (i.e., HDS, ballasted flocculation, and conventional sedimentation) were able to reduce target metal concentrations to well below Canadian guidelines (i.e., total zinc and total nickel < 0.5 mg/L, total copper < 0.3 mg/L) using either CKD or lime. Additionally, mine water samples treated with CKD generated lower sludge volumes than those treated with lime (i.e., 50 versus 100 mL for conventional sedimentation and 100 versus 200 mL for HDS) even with increased concentrations of solids introduced during treatment. This is most likely due to slower neutralization rates when using CKD, due to its lower solubility, as well as finer particle size. The sand-ballasted flocculation process was able to reduce final turbidity in CKD-treated samples while the HDS process did not when compared to conventional sedimentation, making the ballasted flocculation process preferable for reducing final solids concentrations in CKD-treated mine water.

Aug 1, 2013

By A. H. Duffield

"Forming part of the Prairie Evaporites, the sylvinite layer mined at Alwinsal underlies the Blairmore quicksands and the water-bearing Devonian formations. Production is achieved by a method of trackless, continuous mining of rooms, leaving pillars for natural support. The paper describes the development of the mine, and the equipment and organization employed in the operation and maintenance of the underground facilities."

Jan 1, 1972

By L. Xia, B. Hart, J. Nigim, Z. Chen

"Grinding ore is an important step in the flotation process. Not only does grinding reduce particle size and liberate minerals, it also creates conditions for reactions to occur on particle surfaces that can aide or inhibit flotation. There have been numerous studies examining various grinding regiments and the effect on flotation pulp chemistry, including autogenous grinding and using media of variable composition. There have been however, few studies looking at the effect of variability in grinding media size on pulp chemistry and subsequent flotation. This study attempts to link changes in pulp chemistry in response to variations in grinding media size to flotation recovery. It uses probes mounted in the grinding chamber (pH, Eh, DO, and conductivity) to monitor pulp chemistry changes during grinding of a Cu-Zn ore. Surface chemistry analysis by ToF-SIMS was performed on sphalerite from the mill discharge. Activator and depressant species were monitored on the mineral surfaces and their presence was evaluated in the context of variability in pulp chemistry linked to differences in grinding media and its ball size.INTRODUCTIONIt has been widely recognised that not only does grinding reduce particle size and liberate minerals but the grinding environment has a large effect on the flotation of sulphide minerals. This effect is attributed to Eh change, iron hydroxide coating on surfaces, oxygen reduction, precipitation from solution and galvanic coupling (Grano, 2009). As early as 1960, it was reported that after grinding the ores in an iron mill the natural floatability of sphalerite was reduced significantly (Rey and Formanek, 1960). Kocabag and Smith (1985) studied on the industrial circuits showing that the depression of sulphides flotation in a steel mill is possibly due to the coating of iron oxidation products. Peng, Grano, Fornasiero, and Ralston (2003a, 2003b) found that iron contamination from grinding media plays a dominant role in depressing galena and chalcopyrite flotation. Huang, Grano, and Skinner (2006) reported the same observation in the flotation of arsenopyrite."

Jan 1, 2016

By H. Kolcz, G. S. Dobby, R. Stratton-Crawley, S. W. Wilson

"The Matte Separation plant at Inco's Copper Cliff Smelter Complex is described. The continuing implementation of flotation column technology in the flowsheet in various applications is reviewed. Comparative studies on 0.038, 0.10, 1.1 and 1.8 m diameter columns have been carried out. It was demonstrated that consistent metallurgical performance was obtained with both pilot- and plant-scale units. Grade-recovery relationships for plant columns can be predicted with confidence from data obtained from test equipment. The work indicates further areas of the flowsheet in which columns present an attractive alternative to conventional cells. INCO’s MATTE SEPARATION PROCESSNickel concentrate from Inco’s Sudbury area mills has been processed in the Copper Cliff smelter for sixty years. Prior to that, Sudbury ores had been smelted directly. Historically, copper-nickel separation from smelter converter matte was achieved by the classical Orford process. In the mid-1940s Inco developed an improved separation scheme based on mineral processing methods, the Matte Separation Process. A generalized Copper Cliff Smelter Complex flowsheet is shown in Figure 1.Iron sulfide and gangue contained in the nickel concentrate are rejected in the smelting-converting process. The molten product, typically containing 50% Ni, 25% CU and 22% s, is cast at about 1000 ºC, into floor moulds and allowed to slowly cool for four days. During this period nickel sulfide (heazlewoodite, Ni,S,), copper sulfide (chalcocite, cu,S) and a copper-nickel metallic alloy precipitate and form a coarse grain structure that is amenable to separation by physical means. The phase chemistry of this system has been described previously by Sproule et al (1). This matte then becomes the feed to the Matte Separation Process.A simplified block flowsheet of the Matte Separation Process is shown in Figure 2. Matte ingots, typically weighing 20 tonnes each, are broken and crushed in a three stage crushing plant to approximately minus 0.01 m and conveyed to the Matte Separation building. Grinding is carried out in two parallel circuits each consisting of a rod and ball mill in series producing a flotation feed which is 65% minus 44 microns. Typical throughput of each grinding circuit is 650 tonnes/day. The metallic fraction of the feed is recovered by magnetic separation. This product, containing about 66% Ni and 15% CU, is a major component of the feed to the Copper Cliff Nickel Refinery."

Jan 1, 1990

"Sedimented hydrothermal precipitates of silica, now fine-grained quartz, are described from a Pb-Zn-bearing vein system. Their discrimination from the wall-accreted fine-grained quartz that is common in the shallow parts of epithermal systems is discussed. Local fine-grained (<0.3 mm) quartz accumulations occur in a suite of veins with otherwise normal drusiform and crustified infills. This sediment may fill the vein above chokes in steep segments (axial plugs), or form continuous layers within the footwall material where the vein is inclined at low to moderate angles. Pads of fine-grained sediment are deposited on the upwards-facing surfaces of wall-rock clasts and of drusiform crystals growing from the vein walls. The asymmetry of these deposits differentiates them from the more common symmetrical, crustified walllining deposits of fine-grained quartz and opaline silica, and requires a gravity-controlled, sedimentary depositional mechanism.Thin section examination shows that much of the fine-grained quartz is present as elongate prisms. The prism habit was present soon after deposition, but it is not possible to identify unequivocally the original sedimented grains. Sedimentation of vein- and wall-rock-derived detritus is also recognized. Deposition of the fine-grained sediment accompanies normal in situ drusiform growth of quartz and other vein minerals. The mammilated and spherulitic textures associated with accretion of amorphous quartz are entirely absent from the Tyndrum veins with sedimented materials. The literature on modern hydrothermal waters and physical chemistry of silica precipitation shows that precipitates of silica suspended in hydrothermal fluids are amorphous and derived from colloidal silica. It is argued that much of the suspended silica was present as quartz at the time of deposition or was converted from amorphous silica almost immediately after deposition.Hydrothermal sediments and their distribution potentially provide information on flow directions and velocity in veins. Plugs of sediment obstruct vertical flow and lead to local flows with large horizontal components. It is shown that sedimentation features occur in other deposits and can involve other minerals. If the features seen here can be scaled up to the size of major veins, they may result in up and downdip variations in mineral assemblages and abundances, which may affect grade."

Jan 1, 2007

By Z. F. Lodhi, J. H. W. De Wit, H. A. Terry

Zinc and its alloys have been extensively used as replacements for Cadmium coatings in aeronautical and automobile industries. Zn alloys with low Co or Fe have been highly investigated but coatings with higher amount of Co are very difficult to achieve due to anomalism associated with these coatings. Anomalous Zn-Co-Fe alloy is a relatively recent addition to the family of Zn alloys. It is found that the addition of Fe in the electrolyte assist in overcoming the anomalism. In this research Zn-Co-Fe alloys especially with higher amount of Co (>15%) and Fe (~1%) are investigated, after overcoming the anomalism associated with its deposition, and the corrosion resistance is compared with pure Zn and Cd. It is found that an increase in Co to higher than 25 % accounts for a shift in the OCP to a level near Cd yet keeps it electronegative to steel. The coating shows superior corrosion resistance, in terms of its sacrificial and barrier properties in 3.5% NaC1 as compared to Zn and Cd.

Jan 1, 2006

By N. Tounsi

The use of analytical modeling of continuous chip formation in conjunction with orthogonal cutting experiments was presented in the open literature to identify the coefficients of material constitutive equation within the practical range of stress, strain, strain rate, and temperature encountered in metal cutting. Identification of reliable constitutive data was hampered by a lack of a reliable model for the prediction of the primary shear zone thickness that affects directly the effective strain rate field. An original analytical model to determine the primary shear zone thickness is proposed in this paper. It is based on the mechanics governing the material flow in the primary shear zone. Based on the distribution of the hydrostatic pressure and the forces measured from orthogonal cutting tests, the model that describes the thickness of the primary shear zone is derived. To validate the model, FE simulations of chip formation using DEFORM3D were carried out for different materials and cutting conditions. The results of the analytical model are in reasonable agreement with FEM results.

Jan 1, 2006