Search Documents

By Jim Henry

I would say mainly the cost. I showed only 3 cases. One of them was the one that Allen just described and there were two other cases. In those cases it was fairly easy to develop a solution using limited mobility grout to treat the soft soils suitable for the limited bearing pressures required by the structures. LMG readily provided a fairly reliable system for the foundation support at a reasonable cost.

Feb 10, 2003

By A. E. Fiorato

A test program was conducted to evaluate use of high-strength concrete in drilled shafts (caissons). The objective of the program was to determine if internal temperatures developed during cement hydration, or other characteristics of high-strength mixes, affect in-situ strength and stiffness. This paper covers strength results. Two 10-ft (3.0-m) diameter by 40-ft (12.2-m) deep caissons were constructed using two different commercially available high-strength concretes, a "low-heat" and a "high-strength" mix. Measured 6x12-in. (150x300mm) moist cured cylinder strengths at 56 days were 13,690 psi (94 MPa) for the "low-heat" mix and 17,130 psi (118 MPa) for the "high-strength" mix. Compressive strengths and moduli of elasticity of cores taken from the caissons were compared to those of companion cylinders made during casting of the caissons and stored in a moist room. Strengths of 4x8-in. (100x200 mm) cores taken at four ages and tested between 34 and 398 days averaged 81% of strengths of 6x12-in. (150x300 mm) moist cured cylinders at corresponding ages. In-situ (core) strengths of the caissons did not appear to be measurably affected by temperature. However, the data indicate that core strengths were sensitive to level of consolidation, as reflected in entrapped air voids. Overall, the results indicate that high-strength concretes can be used in drilled shaft (caisson) foundations.

Jan 1, 1991

By A. Lyndon

Vertical and lateral load tests were carried out on two 13 m deep bored cast-in-place instrumented piles, socketed into weathered sandstone. The first pile, 1200 mm in diameter, was loaded vertically to a maximum of 16000 kN and then loaded to failure under lateral load (1900 kN). The second pile, 1500 mm in diameter, was tested under lateral load up to a maximum of 2400 kN. It was found that the deflections of the 1200 mm pile were more than twice those of the 1500 mm pile under similar loads. The soils on the site are not easily tested in the laboratory, or by conventional insitu site investigation techniques, parameters needed in design can only be reliably obtained from pile test results. In this report shear moduli are back analysed from the vertical load test and the two lateral load tests. For these similarly installed piles very different design parameters were determined from the lateral load tests, the only known major difference between the piles being that the 1200 mm pile was loaded vertically before it was loaded laterally. Changes in G values needed to match performance under vertical load if applicable to lateral loading could have accounted for a significant amount of the difference.

Jan 1, 1989

By Brian Maroney

In this paper an overview of the California Department of Transportation's (CALTRANS) bridge design criteria is presented. Special emphasis is focused upon seismic design and retrofit criteria. Topics include earthquake load definitions, foundation and structure type selection, structural earthquake analysis, and structure behavioral requirements.

Jan 1, 1993

By S. P. Lin

The numerical models of nonlinear piles for deep foundations are studied in this paper. The purpose of these is to clarify the mechanical behaviour of deep foundation nonlinear piles subjected to axial and lateral loadings. Based on the site data of p-y curve as well as t-z curve of foundation soils, it is possible to evaluate pile performance under above mentioned loads by means of combined FEM/FDM models. Numerical examples are presented in tall building and offshore jacket for illustrating the technique, it show high efficiency of these models. Some information to be interested by design engineers are given, especially for those who pay very concerns on the interaction behaviours of structure and its pile foundation.

Jan 1, 2010

By Elizabeth Varghese, Sanket Rawat, Prachuryya Kaushik, Ravi Kant Mittal

"Geo5 Software is gaining popularity worldwide due to its expediency in analysis and design of pile foundation. The analysis is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards. Moreover, the ultimate resistance of pile in the software is based CSN 73 1002, Fellenius method, NAVFAC DM 7.2 and Tomlinson method. Due to the specificity in calculation of ultimate resistance, it becomes necessary to validate the results arrived using the software for better accuracy. Furthermore, the above-mentioned methods are not necessarily popular in every design offices. Therefore, an attempt has been made to predict the efficiency of Geo5-v15 software to analyze the pile foundation by comparing it with the results obtained using the analysis based on Indian Standard IS 2911:2010, performed with spreadsheet specifically designed for the same purpose. The accompanying outcome of the comparison and several shortcomings found in the design part associated with the software has been highlighted in the later part of the paper. Besides, the optimization tool present in the software is also described for the more efficient and economic design of pile foundation, hence contributing as practical aid to structural engineers.INTRODUCTIONThe analysis of individual pile foundation and pile in groups can be said to include the three main important parameters – Ultimate bearing capacity, Settlement and Structural Design. The first two parameters are to be evaluated to check the reliability of foundation against ultimate limit state and serviceability limit state. The third parameter includes the analysis of pile against both horizontal and vertical load. This parameter mainly intends to evaluate the size of foundation and the amount of reinforcement. Geo5 is a software which can expediently compute the above mentioned three parameters just by the mere input of the necessary factors. The ultimate bearing capacity analysis in Geo5 is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards depending upon the drained and undrained condition of soil (Bowles, 1968; CSN 73 1002,1987; Felenius,1991; NAVFAC DM 7.2,1984; Tomlinson,1977). However, the method mentioned in IS 2911 (2010) is not the same and have slight variations in way of evaluating the parameters which affect ultimate bearing capacity. Therefore, it becomes necessary to evaluate the efficiency of Geo5 with respect to the value of ultimate bearing capacity and therefore, asserting the confidence in the software based method for the convenience of the designs in Indian Scenario. The present study aims to evaluate the efficiency of Geo5 v-15 software in predicting the ultimate bearing capacity of pile foundation. The results of the software are compared with the bearing capacity calculated using IS 2911 (2010) with the help of excel sheet. Moreover, as the software is frequently put under revision, therefore a comparison of this version has also been made with the latest version of Geo5 (2017) to check whether the latest revision has accounted for the discovered shortcomings. The design steps performed in the software is also shown. As Geo5 make use of IS 456 (2000) for the design purpose, hence it can be considered as reliable with respect to the estimate of the third parameter. Furthermore, the optimization process is also shown in the later part of the paper to emphasize the simplicity of the software in economizing the design cost."

Jan 1, 2017

By B. Sivarama Sarma, Biswabikash Rout

"Seepage control has to be achieved with plastic concrete cut-off diaphragm walls in dam structures. Materials selected for construction of cut-off walls must be durable, impermeable and have stiffness comparable to the surrounding soil.Plastic concrete provides a feasible and economical solution for construction of durable and impermeable cut off walls for dam structures. Plastic concrete wall should not be understood as a concrete wall with similar mechanical properties of concrete used in buildings, piles and spillways sections. Though it consists of the same materials as those of conventional concrete it has the major differences in end product due to predominant addition of bentonite slurry in the mix with very high water cement ratio. This makes the hardened concrete with very low compressive strength less than 5MPa and high failure deformations after the peak load.This technical paper examines a case study, the typical specifications on demand for construction and the issues corresponding to misunderstanding of the material as a structural grade concrete material. Conclusions were drawn based on a few project site quality data and trial mix experimental data. The anomalies in specifications on demand for construction of curtain wall in a dam structure were removed with modifications.INTRODUCTIONDiaphragm walls which are constructed in trenches made of plastic concrete basically serve the function of seepage control under confined measures. They should have the ability to sustain and undergo large plastic strains as compared to conventional concrete. The three basic mechanical properties of plastic concrete cut-off walls are to have least permeability, minimum strength to retain its shape and ability to undergo large deformations under confined loading conditions. The constituents of plastic concrete are cement, bentonite, coarse and fine aggregates, chemical additives to improve flow of concrete and sometimes to retard the setting time and water."

Jan 1, 2017

By Roger A. Bullivant

The introduction of this size and type of piling rig is intended to address a multipurpose foundation activity. The 8000 denotes the size of equipment that is attached to the mast, namely 8000 Kg. Larger equipment can be carried subject to adjustment of rig geometry. The 8000 series rig will easily accept hydraulic piling hammers and CFA equipment, but for the purpose of this discussion it will be equipped with an auxiliary power pack that is matched to twin vibrators. The design of the siamesed vibrators allows long tube equipment or piles to be driven with a short mast configuration that provides a lower overturning risk. It is easily adapted within minutes to carry out other foundation requirements that are required on the same contract. The piling and ground consolidation activities that can be undertaken by the 800 series machine are:-

Jan 1, 1995

By Edward Jacobsen, Patrick J. Lydon

"The ongoing expansion of the Oak Creek Power Plant in Oak Creek, Wisc., includes a tunnel bored in rock that connects to four vertical intake shafts approximately 1.5 miles (2.4 km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to install these intake shafts. In spite of delays that shortened the May to September construction season by up to 50%, four shafts and liner assemblies were drilled in 2005 and 2006. The shafts were connected to the tunnel in 2007 by mining upward to reach the lower portion of each liner and then removing its internal bulkheads so that lake water fl owed into the tunnel. The project is one of the largest private construction projects ever undertaken in Wisconsin. The expansion adds 1,230 megawatts of generation. In addition to the tunnel and offshore work, there will be 16 miles (26 km) of railroad track and 6 million cubic yards (4,600,000 m3) of earth work. The 27 ft (8.2 m) diameter tunnel, drilled some 150 ft (46 m) below the surface of Lake Michigan, originates onshore at a pump house. A structural slurry wall was constructed as the foundation for the pump house. The tunnel passes to the south near the current water intake before bearing east toward the new offshore intake shafts, which are 12 ft (3.6 m) diameter by 108 ft (33 m) long steel liner assemblies. These were grouted in place from approximately 3 ft (1 m) above the crown of the intake tunnel and then to 20 ft (6 m) below the lake bottom.Site GeologyOffshore. The plant site is north of the Racine-Milwaukee county line in an area affected by glacial activity. The soil conditions encountered at each shaft location were consistent, with noticeable variations occurring in the top of rock elevations that sloped downward from the innermost to the outermost shaft."

Jan 1, 2008

By Tatiana Tronda

"The territory of Belarus is characterized by nonhomogeneous ground conditions. In some cases soft ground layers can reach tens of meters in depth. Application of piles and other conventional foundations is rather difficult and expensive in such complicated conditions. Alternatively for the first time dry concrete columns were applied to improve the saturated soft soils at two sites. As there is no design methods for calculation of bases improved by dry concrete columns static penetration and static load tests were carried out to check the bases on availability. Considerable increase of toe resistance and Young modulus was achieved for all types of soil. Practical application, technology and test results are described in the paper. According to comparative calculations the cost of foundations on the base improved by dry concrete columns can be 32-75% lower than the cost of conventional pile foundations depending on ground conditions.INTRODUCTIONPile foundations, sand cushions or dewatering are usually applied in complicated ground conditions which are caused by presence of saturated soft soils. If the depth of soft soils reaches 20 m or more, conventional foundations have limited application, high labor and construction cost. A rational solution in such conditions is a ground improvement of upper soft soils. It allows the loads to be transferred on upper ground layers and the stresses to be dissipated considerably before reaching underlying soft ground layers.One of the effective ground improvement methods for saturated soft soils is the reinforcing by dry concrete columns (Fig. 1). The method allows saturated soft soils to be compacted and be drained at the same time. As a result strength and deformation characteristics of natural soils improve (Tronda 2013, ?????? 2014).Unfortunately, there is no design and computing methods for the ground improvement by means of dry concrete columns. However, at present the methods are under development on the basis of theoretical and experimental researches.TECHNOLOGYThe dry concrete columns are fulfilled in pressed wells according to technology of vibrostamped piles. Wells are pressed by vibratory hammer with the closed ended casing (Fig. 2) that provides compaction of surrounding soft soils. Then the casing is filled with dry concrete mix (Fig. 3). The casing end remains on the design depth and the casing is removed by vibratory hammer. The removing of the casing with vibration enables compaction of dry concrete mix inside the well. Dry concrete mix drains surrounding saturated soft soils improving its properties and the compaction speeds up the consolidation process. Over time the dry concrete columns fasten absorbing water from surrounding saturated soft soils that is need for hydration of cement (Fig. 4, 5)."

Jan 1, 2016

By P. V. Chandramohan

"The paper deals with the arrangement of structural members for a retaining structure used as a berth in the port of Krishnapatnam. The height of retention is 24.3m. A T-shaped diaphragm wall acts as the retaining surface. A relieving platform has been provided at the top to ease lateral earth pressure on the wall. The diaphragm wall is tied back to a combination of vertical and raker pile. Later, this arrangement was altered to replace the relieving platform with just lowering of ground level below the berth. The tie back was changed to a classical A-frame anchorage. At certain reaches, installation of piles pointing towards the rear was obstructed by a conveyor structure. The anchorage was then changed to include a vertical pile and a pile that points towards the front of the berth. Change in position of inclined pile alters the force in the pile from compression to tension.GeneralPort is a major link in the multimodal transport chain. Berth is the heart of the Port infrastructure. It is here the ocean freight changes to land transport. The change-over, warrants special type of heavy duty handling equipment. The equipment and the process necessitate deep seated foundations. On one side of the berth, deep drafted ships would be berthed. But adjacent to this heavy duty cranes would be operating at the deck level. Berths are of various types. Some are founded on piles and may project into water. Some operators prefer a retaining structure. At the port of Krishnapatnam, a retaining structure was preferred. Dredged level at the berth was to be -20. Deck of the berth was at +4.3. This meant that the height of retention of soil was 24.3m. Ports are generally located near the coast. Subsoil in the port area generally consists of cohesive material of low shearing strength. The berth has to cater to imposed vertical and horizontal loads.Structural functionFor bulk cargo and containers, berth has to support the two crane tracks. These tracks will carry heavy wheel loads of the crane. Besides, the space between the tracks would be used for stacking of cargo or hatch covers. In short, the deck will be subjected to heavy surcharge. This vertical load will manifest as additional lateral force on the retaining wall. Since the height of soil to be retained is high, it is a practice to relieve the lateral earth pressure due to the heavy surcharge of the wall. This is done by providing a relieving platform. The surcharge of superimposed load on the deck and the self-weight of the soil up to a few metres below would be relieved by a suitable platform. This vertical load would be transferred directly to deeper levels through piles. Mooring pull is a horizontal force exerted by the vessel on the bollards towards water side. Berthing force is exerted by the vessel during berthing, through fenders and acts towards land side.Diaphragm walls are usually employed as the retaining face. If the height of retention is less, these walls can cantilever out but in the case of large retention, they have to be tied back. The ties are to be anchored on to suitable arrangements like a dead-man or an A-frame. Berthing structure in the early stages at Krishnapatnam port is shown in fig 1."

Jan 1, 2015

By Joanna Bzówka

Nowadays, there are some new requirements for the supermarket floors. The floors are loaded by high point- and moving-loads. In spite of this fact, it is necessary to ensure the stiffness of the floor and the stiffness of its support. When pile foundations are designed in the case of weak soil, the piles are recommended under the foundations of the supermarket and also under the floor layers. The example of foundation of a typical supermarket located on long­standing municipal dumping ground is presented. Indirect foundation - CFA piles, 0.5 m in diameter and 4.5 to 20.0 m long, was de­signed. Fifteen trial loading tests were carried out.

Jan 1, 2006

By James C. Scott

Compression and tension load testing were performed on bored concrete piles installed to depths of 18 to 34 meters below excavation levels for a large mixed-use development in Kuala Lumpur, Malaysia. The 900 mm diameter piles were installed in weathered graphitic schist bedrock. Load testing confirmed the side shear and end bearing capacities of the piles. The work formed part of the investigations for the 56,000 m2 site which includes a 79-story office tower, hotel tower, apartment tower, retail complex, and plaza area underlain by 4 to 6 basement levels. The paper provides the results of the site investigations, pile-load testing procedures, pile-load settlement behavior, and shaft load distribution.

Jan 1, 2007

By Louay Owaidat

The United States Army Corps of Engineers (USACE) Sacramento District awarded a $64 million construction contract in February 2020 to the Maloney Odin Joint Venture for 3 mi (4.8 km) of levee improvements along the Sacramento River East Levee (SREL). This project kicked off approximately $1.5 billion of work to upgrade levees along the American and Sacramento Rivers and widen the Sacramento Weir and Bypass. The project received the 2021 ASCE Region 9 Project of the Year Award. Contract 1 improved levees along five segments of the river, the longest segment being a 2 mi (3.2 km) reach from Garcia Bend Park to the Freeport Intake Facility in the Pocket neighborhood of Sacramento.

Oct 1, 2022

By Kazimierz Gwizdala

In the paper the method for estimation of settlement of vertically loaded piles in a group is presented. The method is generally based on the hybrid procedure with non-linear solution for single piles and with interaction between them for the low-strain shear modulus. Some attention is paid to the influence of deformation and strength parameters used in calculations. The applied model is verified in the framework of the research programme carried out recently in the Geotechnical Department of Gdansk Technical University. It concerns monitoring and analysing the settlements of the existing structures on piles. A comparison of calculation and measurements results for two tested buildings is presented as an example.

Jan 1, 2002

By Sandeep Pattnaik

Spring stiffness of soil and rock at different depth is often required for a pile structural model. If the pile is rested in multiple layers of soil, then it is rather more complex to simulate the soil in a structural model. The spring stiffness will vary based on density of soil strata over the depth. When a pile is socketed in weathered rock followed by a soil layer, a sudden change in subgrade modulus can influence the pile deflection drastically. Determination of soil spring and simulation of the pile in this condition required correct interpretation of subgrade modulus. The conventional approach of pile spring calculation underestimates the spring stiffness by ignoring underlaying stiffer layers. A finite difference method (FDM) of analysis can reasonably estimate the p-y of soil / rock based on subgrade modulus of each layer. However, the transition between the layers can be better simulated as per the deflection pattern of the pile. The lateral deflection of the pile is mainly dependent on the stiffness of soil layer surrounded by the pile. Generally, the lateral influence of a pile varies from 4D to 6D depending on the soil type. Therefore, soil spring stiffness around the pile would require special attention of a Geotechnical engineer to avoid uncertainty in the prediction of pile behaviour. In this paper, emphasis has been given to develop an approach for pile spring stiffness design. A standard software program LPile has been used to develop p-y curves of soil and rock layers at different depths and then converted to soil/ rock springs over the depth. Modulus of Subgrade Reaction as given in IS 2911 (Part2) was also used to correlate the spring value for different type of soil. Obtained analytical results were compared with full scale field trial for lateral deflection of pile. A good agreement between these two approaches has been established. The effect of soil structure interaction in the structural model shall be simulated by assigning an equivalent vertical and horizontal soil spring, which is developed by Winkler’s soil spring approach. A simplified design principle for calculating the pile spring is discussed in this paper. This approach has been extensively used in Mumbai metro elevated line pile design.

Nov 1, 2022

By Scott Dodds

"The Oxford Hydroelectric Station was a unique project that incorporated a variety of dam strengthening methods to stabilize the facility in order to meet the standards required by Federal Energy Regulatory Commission (FERC). The dam stability and Probable Maximum Flood (PMF) remediation work consisted of (1) construction of a new emergency spillway; (2) installation of 75 high capacity rock anchors; (3) construction of an anchored concrete powerhouse buttress; (4) construction of cast-in-place and sheetpile flood walls; and (5) design and construction of a permanent soil nail wall. INTRODUCTIONThe Oxford Hydroelectric Station is one of 11 hydroelectric facilities owned and operated by Duke Power along the Catawba/Wateree River. The Catawba River originates in the foothills of the Appalachian Mountains just west of Morganton, North Carolina. The river flows east out of the mountains and, at a point just below the Oxford Dam, the Catawba River turns and heads southeast. The Catawba River continues to flow southeast past Charlotte and into South Carolina where it eventually becomes the Wateree River. The Wateree River eventually flows in to the Atlantic Ocean.Located a few miles east of Hickory, North Carolina, the Oxford Dam and Hydroelectric facility is in the upper reach of the Catawba River. Oxford Dam creates the third impoundment along the river known as Lake Hickory. Lake Hickory is well known locally for providing many outdoor activities such as boating, jet skiing, canoeing and fishing. The dam and powerhouse were put into operation in the spring of 1928.Key features of the dam include a short embankment section on the south end of the structure, a 391-foot (119m) long south bulkhead and powerhouse, 540-foot (165m) long gated spillway section and a 235-foot (71.6m) long north bulkhead. The maximum height of the dam is approximately 100-feet (30m) from the crest to the dam/rock interface. (See Figure 1).The work associated with this project is the result of licensing requirements of the Federal Energy Regulatory Commission (FERC) which mandates that all hydroelectric facilities have the capacity to safely discharge runoff created by a critical rainfall event defined as the probable maximum flood (PMF). Duke Power, a division of Duke Energy (DUKE) submitted an initial PMF report in 1992 which indicated that at the Oxford Dam would be overtopped by approximately 10-feet of water during the modeled PMF event. Given the duration and depth of the overtopping, significant damage to the facility and a possible breach could result. Therefore, modifications to the existing facility were necessary to satisfy the report of the PMF model."

Jan 1, 2005

By Don W. Dotson

In 1962, Kondner prepared several papers dealing with hyperbolic stress-strain response of cohesive soils. The following year, Brinch Hansen proposed 80% and 90% failure criteria for stress-strain behavior of cohesive soils. Fellenius was instrumental in popularizing these failure criteria for pile load tests and offered a direct solution equation for the failure load according to the 80% failure criterion. Since the 90% Criterion has been incorporated into the International Building Code, equations for the direct solution of the failure load at the 90% Criterion would be useful to practicing engineers. This Technical Note supplies the derivation methodology for the 80% Criterion and provides expressions to determine the load and deflection at failure for the 90% Criterion.

Aug 1, 2013

By Chandramohan P. V

A unique tension pile where the pull is at a point a certain distance below the top of the pile. The pull is transferred by a cable consisting of high tensile strands. The HDPE duct of the cable prevents bond between the strands and pile concrete in upper portion. While soil friction on the pile will act downwards on the whole length, there is tension in the bottom portion of pile, there will be compression at the top portion.

Nov 1, 2022

By Krishnendu Mandal

"For a multi-story building project in Kolkata, a pile load testing program was conducted to minimize pile performance uncertainty resulting from variable subsurface conditions and to verify the pile load vs. settlement response. The program consisted of performing five (5) instrumented load tests on augured cast-in-place (ACIP) pre-production test piles. Vibrating-wire strain gages and extensometers were installed in the test piles at strategic locations to enable measurements of the load vs. deformation behavior of the test piles. This paper presents a description of site subsurface conditions, test pile installation, instrumentation setup for a maintained load test (MLT), static compression pile load test results, and pile instrumentation result interpretation. Average mobilized unit shaft resistance values are calculated.2.0 INTRODUCTIONThe project site is located in Kolkata, near river Ganges, and the proposed development plans consist of constructing six (6)25-story (G+25) towers; see Fig. 1 and Fig. 2 below for approximate site location and proposed development layout, respectively. The buildings were designed to be supported on ACIP piles. A field load test program was implemented to verify sub-surface conditions and pile design. The test program consisted of installing Five (5) instrumented test piles numbered LP1A and B through LP6A and B, and performing static compression load tests on these piles. The piles were instrumented with vibrating-wire strain gauges and extensometers, so that the pile shaft resistance distribution along pile length and the pile toe resistance could be interpreted using direct instrumentation measurements."

Jan 1, 2015