Search Documents

By G. Ranjan

The designers and the practicing engineers have started using latest and cost effective techniques of ground improvements which utilise the weak and poor sub-soil deposits efficiently for the civil engineering construction. In the present investigation, a new concept of 'skirted granular piles' has been advocated. An effective method of construction of granular piles as an economical alternative to vibroflot, and the skirt has been developed. The construction technique is based on indigeneous know how which effectively utilises the man-power technology avoiding import of costly equipment suiting to the developing countries. Full scale insitu tests have been carried out at four sites, having different soil conditions, on virgin weak sub-soil, and improved ground by casting plain and skirted granular piles. Effectiveness of different types of skirt has been demonstrated through insitu tests. A simple analytical approach has been proposed to predict the ultimate pile capacity. The predicted values of ultimate capacity have been found to demonstrate a good correspondance. Granular pile behaviour in terms of pile depth, diameter, spacing and stress deformation characteristics of the improved ground have been discussed. A significant improvement in ultimate capacity in improved ground has been noted. This is further augmented when granular pile group is skirted.

Jan 1, 2010

By Terence P. Holman

Micropiles are employed to retrofit existing foundations, including underpinning prior to future construction operations and resupport of existing structures that have experienced distortion and settlement. This paper presents analyses of the two case histories requiring the use of micropiles in these applications. The first case history involves micropiles used to resupport a settled pump station next to an excavation which had suffered basal failure and ground loss. A compression load test pile experienced plunging failure which, after analysis of the strain-gauge data acquired during the test, was attributable to a greater degree of disturbance to the subsoils beneath the site than anticipated. After construction of the micropiles around the pump chamber a synchronized jacking system was used to lift and right the 320 kip chamber structure, followed by resupporting it on the newly constructed piles. The second case history entails the use of micropiles for direct underpinning support of existing columns prior to a utility tunnel installation within an existing high-bay warehouse structure. The design constraint that most significantly affected the successful completion of this project was the desire to bond the new piles into the existing reinforced concrete foundations. As a result of the coring method through the footing, the ultimate bond stress measured during a pullout test was more than twice that assumed in the design. Monitoring of the underpinned columns during trench excavation indicated that the system performance was acceptable. These case histories reinforce the concept that lower capacity micropiles can provide a rapid means to underpin and retrofit existing structures.

Jan 1, 2007

By Tomohiro Yamasaki

"At the pre-construction foundations of the controlled waste disposal site built at the Port of Kinuura, the clayey soil account for the most, and with lesser amounts of sand compaction piles and sand mat. The cement deep mixing method (CDM) was used to improve ground impermeability and to reinforce the foundations on the seawall. Laboratory mixing and testing was performed to determine the appropriate quantities of cement additive for clayey soil, SCP sand, and sand mat. The test results indicated that maintaining the design strength of qu = 1,550 kN/m2 would require C = 100 kg/m3 of cement additive for all three soil types (clayey soil, SCP sand, sand mat). The permeability performance needed to improve ground impermeability assumes a permeability coefficient of K = 1.0×10-6cm/s. And the clayey soil satisfied the performance requirements at C = 100 kg/m3. However, to improve grand impermeability of the SCP sand and sand mat required more than 5% of particles having diameters of less than 75 µm. Thus, in the latter two cases, the required cement adding quantity was C = 250 kg/m3. The test specimens at one to two weeks after the created with a permeability coefficient of K = 10-6cm/s became permeability coefficient of K = 10-7cm/s six week later due to the effects of cement solidification. So the permeability coefficient declined about one order. The permeability coefficient three months later tends to decline continued with a somewhat lower.INTRODUCTIONBetween 2008 and 2011, the Aichi Seaside Environment Center constructed the Kinuura No. 3 offshore controlled waste final disposal site at Taketoyo in Aichi prefecture. (see Figure 1). The disposal site offers a landfill capacity of 5.21 million m3 and measures 472,000 m2 in area, of which some 344,000 m2 is a managed controlled sector enclosed within an impermeable seawall."

Jan 1, 2015

By Richard T. Stain

"In 2001, a pile trial site was established at Limelette in Belgium consisting of 25 displacement screw piles and 5 driven pre-cast piles. Interested parties were invited to participate in a pile prediction event, whereby they would submit predicted static load test behaviour in the form of load settlement plots. These predictions could be based on soil investigation results supplied by the organizers, or dynamic load test measurements.Following the submission deadline, the organisers released the results of static load tests for comparison.Of all the six participants, including Statnamic, the SIMBAT method was independently accredited with achieving the best predictions.This paper examines at the differences between SIMBAT and other systems, and presents the correlations from the Limelette trial.INTRODUCTIONThe Belgian Building Research Institute (BBRI) initiated an ambitious research programme involving the construction and testing of some 60 trial piles spread between two sites, a clay site at Sint Kateline Waver and a sandy site at the BBRI headquarters at Limelette. The project was financed largely by the Belgian Ministry of Economic affairs. (ref 1.) This paper refers only to the second site.At Limelette, six different types of displacement pile were installed: one driven pre-cast and five cast in place screw piles - Atlas, DeWaal, Fundex, Olivier and Omega. A detailed site investigation was carried out including in-situ and laboratory tests.An international pile capacity prediction event was publicised, participants being invited to predict static pile behaviour. Predictions could be based on:"

Jan 1, 2005

By J. H. Qian

China is one of the countries with comparatively wide distribution of soft soil. In the wake of the rapid developement in the national economy and construction, the improvement technique of soft soil foundation has been perfected gradually. At the present, an integrated system of soft soil improvement has formed, features of such a system are shown by the variety of improvement methods, the complement of theoretical study to project practice. This paper summarizes mainly the following methods: lime column, vertical drain, vibroflotation and dynamic consolidation.

Jan 1, 2010

By Les R. Chernauskas

? What is Integrity Testing? ? Cross-Hole Sonic Logging (CSL) ? Single-Hole Sonic Logging (SSL) ? Typical Specifications ? Case Histories ? Observations and Conclusions WHAT IS INTEGRITY TESTING? General Definition ? Process in which the condition or structural makeup of an object can be evaluated with respect to defects such as a reduction in cross section (void or crack) or reduction in material strength (water, slurry, soil mixed with concrete). ? If the defect is severe enough, it can reduce or alter the load carrying ability of the object.

Jan 1, 2001

By Mohamed A. Eliwah

This paper deals with the determination of hydraulic conductivity of the coastal coralline limestone aquifer of Jeddah, Saudi Arabia. This coastal area has witnessed urban development and establishment of towers which requires deep foundations, excavation and dewatering of huge quantities of unconfined groundwater. It is occupied with successive layers of soft detrital and consolidated massive cavernous coralline limestone of the Quaternary age. These layers are encountered at a depth of 1.5m and extend for more than 100m. Hydraulic conductivity values were obtained by analyzing the pumping tests data under steady and transient state conditions. Hydraulic conductivity values help in selecting the proper and safe dewatering system, as well as determination of discharge rates and quantities of groundwater to be withdrawn. Test results obtained from two surveyed sites showed that the values of hydraulic conductivity are greatly variable. It ranges between 118.1 and 1559.6 m/day at the first site, whereas at the second one it ranges between 94.6 and 350 m/day. These high values are attributed to the cavernous nature of the water-bearing formation. Jeddah city could be divided into three different dewatering zones extending from north to south parallel to the coast line. Well point dewatering system could be applied in the first zone while ditches and sumps are the most suitable dewatering method in the second and third zones. Dewatering using deep wells in such highly permeable formation will require withdrawal of huge quantities of water which will be accompanied by washing out fine sediment filling the cavities in the surrounding areas. This will badly affect the nearby buildings through settlement, crakes and other structural damages. Therefore, construction of grouting plug/blanket with thickness of 3.0 m at a depth of 20.0 m is recommended. This depth will be enough to support the plug against the hydrostatic pressure. Moreover, it is highly recommended to transfer the site into closed box, by using diaphragm walls or secant bored piles.

By Alan Alhadeff

Why is mediation being hailed as the wave of the future? The high cost of putting on a trial, over-crowded court calendars and long trial delays have resulted in what prominent attorneys and leading jurists are calling a litigation crisis. In no segment of the legal world are these pressures greater felt than in the trial of the serious construction case. Furthermore, the siege mentality of both the plaintiff and defense bar often leads to a reluctance by either side to make the first reasonable offer for fear of showing weakness. Attorneys operating in the serious construction case arena express concerns that there exist insufficient opportunities for the parties to meet, tell their stories, and negotiate settlement prior to the eve of trial. Mediation, by opening lines of effective communication and encouraging meaningful settlement negotiation, has proven to be a very effective antidote to the litigation crisis.

Jan 1, 1990

By Clif Kettle

The paper will detail the design and execution of passive and active settlement control measures, the means adopted to overcome the various physical and operational constraints, and to meet specified allowable settlement criteria. The paper will highlight the close integration between the tunnelling and geotechnical contractors, designer, and Client, and demonstrate how particular practical difficulties were overcome by both the design and the construction methods.

Jan 1, 2008

By Michael W. Oakland

Weidlinger Associates was retained to evaluate the foundations supporting ten oil storage tanks at a tank farm on the east coast. The tanks were constructed over the site of a landfill which was underlain by deep organic deposits. The tanks were typically 48 ft. in height and ranged in diameter from 60 to 150 ft. The tanks were supported on both wood and steel pipe piles. After more than 35 years of service, an inspection found that up to 25 percent of the piles had separated from the mat foundation. The operations at the facility were temporarily stopped pending further investigation. Weidlinger developed comprehensive finite element models of the foundations for each tank and used random generators to conduct Monte Carlo simulations the range of scenarios of detached support conditions since it was not possible to survey all the piles below the tanks. To confirm the modeled performance and verify stability, each tank was also load tested using water with electronic instrumentation installed by Geo-Instruments. The instrumentation provided real time, web based monitoring during testing in areas which would otherwise be inaccessible during loading. Through inspection, complex modeling and sophisticated load testing, Weidlinger and Geo-Instruments were able to show that all but one of the tanks could safely be put back into service. This paper details the analysis, Monte Carlo simulations and instrumentation and load testing performed for this unique project.

Jan 1, 2009

By Lee S. Vanzler

Atlantic Wharf involved the construction of a six-level underground parking garage and a 32-story high rise tower along the historic Boston Harbor waterfront. The site, historically known as ?Russia Wharf,? consisted of filled land initially created in the late 1800s by extending the shoreline toward the harbor as the urban population and land needs grew to support expansion of commerce and trade. Redevelopment required solutions to address relics of waterfront structures (granite block seawalls, piles, and piers), weak subsurface soil conditions, tidal groundwater levels, and contaminated soils resulting from previous site usage and filling. The foundation system, consisting of drilled shafts with column loads up to 14,000 kips (62,272 kN), concrete diaphragm wall (slurry wall), and up-down construction methodology, was chosen to address these factors. As a prerequisite for development, selected portions of the façades of the former historic buildings were required to be preserved, protected, and incorporated into the final building configuration. The historic façades were temporarily braced and supported prior to the demolition of the buildings and commencement of below-grade construction. This paper will describe the considerations in the selection of up-down construction methodology along with a discussion of the design and performance of the concrete diaphragm wall and drilled shaft foundations. Up-down construction methodology shortened the overall construction schedule while addressing the lateral bracing requirements for the concrete diaphragm wall and restrictive ground movement tolerances to protect adjacent structures. Below-grade construction was completed in March 2010, and the building was opened for tenant occupancy in January 2011.

Jan 1, 2011

By Nabil F. Ismael, Mohamed El Deeb

"The behavior of laterally loaded step tapered bored piles in calcareous sand was examined by field tests. Lateral load tests were carried out on straight and step tapered bored piles 5.3 m long embedded 5 m below ground level. All piles were installed by augering. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles have a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads. Test results indicate non linear response and substantial increase in lateral capacity and decrease of deflection for the step tapered piles compared with the 0.2 m diameter straight shaft piles. However, beyond a depth of 40% of the pile length, the strengthening of the pile section by enlargement of its diameter had little effect on the lateral capacity and the deflection of step tapered bored piles.IntroductionFor many structures on pile foundations the ultimate capacity under lateral loads is important and may be the controlling factor in foundation design. Examples include transmission tower foundations and fender piles at sea port facilities. Increasing loads on these structures has resulted in piles of large diameter and depth at a significantly higher cost.In this work, the use of step tapered bored piles with a larger diameter along the upper segment of the piles is examined by field testing and analysis on single piles in calcareous desert sands. Lateral load tests were carried out on straight and step tapered piles 5.3 m long embedded 5 m below ground level. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles had a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads for step tapered bored piles."

Jan 1, 2005

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By Scott M. Mackiewicz

This project includes replacement of the historic vertical-lift span Meridian Bridge (U.S. Highway 81 over the Missouri River) that connects Yankton, South Dakota with rural Cedar County, Nebraska. The new 76-foot wide, 1,590-foot long steel plate girder structure required the use of drilled shaft foundations that extended into the underlying Carlile Shale formation. Designers indicated that an individual drilled shaft capacity of about 2,000 kips will be needed at each of the river piers, and based on the subsurface information, 8 to 10-foot diameter drilled shafts extending to about 115-foot would be required for support of the bridge structure. An Osterberg Load Test was performed on one test shaft to determine the ultimate skin friction and end bearing of the Carlile Shale. This paper describes the design and installation of the load test drilled shaft as well as presents the load test results as compared with predicted design values determined using FHWA methods.

Jan 1, 2008

By Yoshio Mitarai, Takeshi Nagatome, Yosuke Tanaka

"This paper describes an application of lightweight soil in a deep water area to stabilize an existing quay wall at the Port of Tokyo. Super Geo Material, abbreviated SGM, is a type of lightweight soil, which consists of dredged cohesive soil, cement and air foam, and is applied in coastal development work, such as port and airport construction. This paper reports a SGM construction project at the Port of Tokyo by using a SGM special plant vessel, which was deployed for the Tokyo International Airport (TIA) Expansion Project in order to achieve large-scale and rapid construction. The key issue in SGM construction is quality control. One key quality issue is control of the mix proportion of SGM in consideration of volumetric changes due to air foam-breaking during pumping and air foam shrinkage due to water pressure when SGM is placed in deep water. A smart technique for placing SGM is also necessary to prevent quality deterioration when SGM is placed in deep water, for example, increased bulk density and decreased shear strength due to water absorption. This paper introduces an actual case of SGM construction with a particular focus on quality control of SGM during construction.INTRODUCTIONSuper Geo Material, abbreviated SGM, is a lightweight stabilized soil which is used in coastal development work in Japan (CDIT 2008). SGM is applied as a backfilling material behind existing quaywalls or above underground structures in order to reduce earth pressure on the existing structure and improve seismic resistance. SGM has been applied in many coastal development projects. In particular, SGM was used at the Tokyo International Airport (TIA) Expansion Project (Haneda Airport) as the backfilling material at a quay wall at the joint between the reclaimed area and pier part in a new runway (Nagatome et al. 2010a & 2010b, Yamatoya et al. 2010, Mitarai et al. 2011). In this project, large-scale and rapid SGM construction was implemented by the special SGM plant vessels within 6 months under the condition of limited construction period.This paper introduces a new SGM construction project at the Port of Tokyo in 2011. This project employed the special SGM plant vessel, “Ryujin Mark II”, to achieve large-scale and rapid construction within a limited period. SGM was also placed in a deep water zone at the maximum water depth of approximately 15 m. Thus, quality control of SGM was a key issue for meeting project requirements. This paper describes the actual SGM construction in the Tokyo Bay area and quality control techniques for SGM, considering volume changes due to pumping and placement below water."

Jan 1, 2015

By Todd Nottingham

Channel deepening of major ports is challenging designers to explore innovative solutions to ensure stability of bulkheads, such as for the Oakland Inner Harbor. This particular challenge was met with the use of the SPIN FIN® Tension Pile for restraint of an HZ combination wall along the Oakland Inner Harbor Shoreline in Oakland, California. A SPIN FIN pile is a pipe pile with welded plates at the pile tip that increase pile capacity. A brief history of the project will be provided as well as results of pile load tension tests, pile strain gauge, and wall deflection under construction loads. Tension pile load deflection results will be discussed with recommendations toward establishing deflection-based ultimate load criteria. A discussion of predicted wall loads and field observed wall loads will be provided.

Jan 1, 2008

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

By Sara Moshfeghi, Seyyed Majdeddin Mir Mohammad Hosseini, Abolfazl Eslami

"Due to variety of current pile bearing capacity methods based on the cone penetration test (CPT), for optimum design, it is necessary to evaluate the performance of such methods in different geotechnical conditions. Geotechnical databases including piling and in-situ testing records have been recognized as useful tools for analysis, design and economical construction. In order to evaluate pile bearing capacity methods, AUT-CPT&Pile database has been compiled including 450 full scale pile load tests and CPT sounding records. This database consists of different pile types with a relatively wide range of geometries and various soil conditions. Forty three records of piles driven in sand deposits were then employed to evaluate effects of ultimate capacity interpretation criteria from load displacement diagrams. The Davisson offset limit criterion, the Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter were compared to estimated capacities from ten CPT based design methods currently used in practice. The Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter lead to reasonable results, the Brinch Hansen 80% criterion showed less scatter. For evaluating the accuracy and the precision of CPT-based methods, the results were compared to estimated capacities. Results of comparison indicate that the CPT-based methods mainly predict the pile capacity withreasonable accuracy.INTRODUCTIONAmong the different approaches of estimating the pile bearing capacity, in-situ tests, especially, the cone penetration test (CPT) are favored due to the cone similarities with piles in modes of installation as well as fast and continuous profiling. This trend is practically well established where deep foundations are to be constructed in soft to medium subsoil deposits (Eslami and Fellenius, 1997; Mayne and Niazi, 2009).Employing different design methods results in a wide range of values which complicates the selection of an appropriate one to determine the pile bearing capacity. Several studies by Briuad and Tucker (1988), Eslami and Fellenius (1997), Abu Farsakh and Titi (2004), Schneider et al. (2008) and Eslami et al. (2011) confirm disparity of different design methods predictions. Thus, for optimum design, it is necessary to evaluate and compare the performance of current methods.Geotechnical databases are known as helpful tools in research and practical applications for optimizing analysis and design and are mainly used for management and interpretation of data, evaluation of design methods, calibrating LRFD or ASD design factors, etc. Pile lateral and axial load tests are examples of databases in geotechnical engineering. A summary of several CPT and pile load test databases is presented in Table 1."

Jan 1, 2017

By Sepideh Damavandinejad Monfared

"In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the behavior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands. IntroductionMicropiles are small diameter (typically less than 300 mm), cast-in-place, drilled, and grouted replacement piles with steel pipes which after being conceived in Italy (Lizzi,1978), were originally developed for underpinning existing structures (Bruce et al.,1990) to arrest and prevent structural movement, upgrade loadbearing capacity of existing structures, repair or replace deteriorating or inadequate foundations or raise settled foundations to their original elevation."

Jan 1, 2017

By Jack Hayes

The design and construction of deep foundations involve many uncertainties. For the designer there are uncertainties regarding soil and ground water variability, regarding sampling and lab testing, regarding analytical techniques and regarding construction technique. The latter being the uncertainty over which the engineer has least control and which may have the greatest impact on capacity. Foundations with a high design factor of uncertainty can be very costly. Foundations designed with a high factor of uncertainty may have a low factor of safety, which can be even more costly.

Jan 1, 2000