Search Documents

By John Wise

Significant movement to an existing slurry wall which serves as a retaining wall on 'O' Street in Southeast Washington, D.C. initiated the Department of Public Works for the District of Columbia to invite specialty contractors to propose a rehabilitation and stabilization for the failed slurry wall. Nicholson Construction Company proposed and was awarded a contract for the construction of an anchored precast lagging and soldier pile wall to be located approximately 4 feet in front of the existing structure with granular fill placed between the new and existing walls. Stabilization of the existing slurry wall also included drilling horizontal weep holes and demolishing the failed panels down to the existing ground surface. A new and improved drainage system was also constructed to increase the amount of water directed toward the existing storm sewer system running along 'O' Street. This paper provides a detailed account of these construction activities.

Jan 1, 2003

By Daniel A. Thome, Robert C. Janke

"Installation of permanent soil nails through distressed mechanically stabilized earth retaining walls is a cost effective and aesthetically pleasing solution when using the appropriate equipment and drilling methods for installation. A forensic investigation was performed on an existing mechanically stabilized earth retaining wall to determine the possible causes for the excessive horizontal displacements and visual structural flaws found along a portion of the wall. Reports concluded that the visual shifting was due to a number of factors including improper drainage in the vicinity of the wall and unsuitable compaction of the backfill material. Conceptual designs were proposed to the owner and the installation of permanent soil nails through the existing precast panels was determined to be the most practical solution. A total of ninety-three permanent soil nails were installed to lengths of up to 40 feet (12 m) through sand backfill and silty day fill using a hydraulic rotary percussion drill attached to a tract mounted excavator.IntroductionThe Illinois State Toll Highway Authority awarded Contract RR-03-5144 in the summer of 2004. Construction work for the project consisted of the rehabilitation of two existing concrete culverts and approximately 100 linear feet (31 m) of mechanically stabilized earth (MSE) retaining wall. The retaining wall is located below the southbound lanes of the Tri-State Tollway near the intersection of Federal Highway 41 in Wadsworth, Illinois as shown in Figure 1.Reports were prepared by Applied Technologies in cooperation with Giles Engineering Associates to determine the condition of the MSE wall and recommended conceptual designs to extend the service life of the wall.Nicholson Construction Company (Nicholson) wasselected as the design-build geotechnical subcontractor to install the recommended permanent soil nails through the existing precast concrete panels of the MSE wall. Rehabilitation of the wall involved the installation of ninety-three permanent soil nails through the existing wall, along with soil nail verification tests and proof tests on production nails."

Jan 1, 2005

By Timothy J. Myers

Expansion and the economic growth in the southwestern region of Missouri necessitated the expansion of State Route 249 and the construction of a new interchange to provide service to the Joplin, Missouri area. The project is located above a former lead and zinc mine in Jasper County, Missouri and includes a five bridge interchange connecting State Route 249 and US Route 171. The variable subsurface conditions, both natural and manmade, prompted the design team to use ground improvement via grouting and small diameter micropiles to provide support for several of the bridge foundations on the project. The scope of work included mine shaft closures, 56,000 ft of overburden and rock drilling, 11,139 ft of micropiles, 524 cy of balanced/stabilized high mobility grouts, and over 8,700 cy of low mobility grout. The selection of the grout used was based on the actual subsurface conditions. Low mobility grout (LMG) was used in voided conditions and for closure of the mine shafts encountered during the excavation. High mobility grout (HMG) was used in fractured rock with the goal of improving the mechanical properties of the rock underneath the future bridge footings and controlling grout volumes during micropile installation. The split spacing method was utilized for both LMG and HMG holes. Geology of the project site subsurface consisted of extremely variable bedrock with strong to very strong limestone, chert, breccia, extremely weak shale, and weak to strong sandstone. Previous activities associated with the mining disturbance (such as partial filled vertical mine shafts, shallow and deep mine horizons, modified hydrology including artesian conditions) further complicates the site subsurface conditions. Real time monitoring and recording of all drilling and grouting parameters was conducted to assist in the evaluation of in-situ geological properties of the site in order to modify the ground improvement and micropile program as necessary. This paper will discuss the design and execution of the ground improvement and micropile program. The project is an excellent example of the use of multiple ground improvement and foundation support techniques combined with real time data analysis to provide a foundation support solution for a complex geological environment.

Jan 1, 2009

By Andrew Pontecorvo

The design of foundations for the tall buildings of lower Manhattan rely on the use of high capacity, rock anchors to resist overturning forces generated by lateral loads from wind, earth, water and, to a lesser degree, seismic forces. Once completed, the proposed towers at the World Trade Center (WTC) site will be among the tallest buildings in New York City. The towers are exposed to coastal winds and from several levels of below grade structure soil and water loads. The design loading required under the current New York City Building Code (NYCBC) is similar to the requirements of the building code used to design the original WTC Twin Towers. We will compare how rock anchors were deployed in the Twin Towers and how they are used in the new buildings. Changes to the building code are less significant that the changes to the design of the structure; that is how the outer skin or perimeter structure interacts with the building core. The result is a significant increase in the number of rock anchors required for the new buildings when compared to those installed in the original WTC Twin Towers.

Jan 1, 2011

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By Arturo Ressi di Cervia

The utilization of diaphragm wall construction in Hong Kong began in 1974 with the construction of the New World Center, the first diaphragm wall job built in the British Colony. That landmark job of which I am presenting a few slides and a schematic description, embodied all of the difficulties and problems which are encountered in the difficult geology of Hong Kong. A small rocky island in the South China Sea, Hong Kong provides one of the finest natural harbors in the world. It is its splendid harbor, coupled with the enterprising attitude of the Hong Kong Chinese and the laissez-fair attitude of the British government which has resulted in the explosive growth of this speck of land soon to revert to the political control of mainland China.

Jan 1, 1993

By Ray Schmahl

The Glenwood Canyon is a 13 mile long river gorge formed by the Colorado River approximately 2 miles East of Glenwood Springs, Colorado and approximately 150 miles West of Denver Colorado, (See Drawing #1). The canyon walls rise some 800 feet from the river elevation on either side of the river. The South-side river bank is occupied by the Denver and Rio Grande Western Railroad. The Northside is currently occupied by completed sections of Interstate 70 and US Highway 6. The railroad was built in the late 1800's and a hydroelectric power generating station was built in about the center of the canyon in the early 1900's. The Highway 6 platform was completed in the 1930's. The design and alignment for Interstate 70 thru Glenwood Canyon began in the early 1970's. The Highway thru Glenwood Canyon was designated a scenic Highway by the United States Congress, thereby allowing certain deviations from standard Interstate requirements. Environmentalists objections to the construction of Interstate Highways thru Glenwood Canyon resulted in especially careful design to avoid adverse environmental impacts. As a result, in many areas the new Highways will have restored the canyon to its more native configuration than what was the case in the building of the US 6 Highway platform.

Jan 1, 1990

By Racquel Nottingham, Marc Mastrantuono, Freddy Lopez

In the digital era that we live in, connectivity and mobility play a decisive role in our daily activities. In this context, insufficient telecommunication infrastructure gives origin to the so called “dead zones” (areas with poor or non-existing cell phone reception), which hinder economic development in small communities and in many rural areas, since they remain invisible to a larger marketplace due to the inadequate cellular coverage. Several countries are working to identify these dead zones and with this information, establish strategies together with mobile providers in order to improve the existing mobile networks by expanding the coverage areas. As a result of the analysis, it is expected that thousands of telecommunication towers for 4G and 5G networks will be erected in the coming years. Telecommunication towers are slender elements that require large shallow foundations to verify primarily the safety against overturning. However in remote areas, it can be advisable to consider alternatives to the conventional shallow foundations, in order to optimize the use of materials (concrete, reinforcement steel, etc.). The following article presents an overview of intervention projects, where telecommunication towers were founded on micropiles. The micropiled foundations allowed to reduce considerably the dimensions of the originally planned shallow foundations. Furthermore, the use of micropiles allows for additional optimization, in combination with pre-fabricated foundations (i.e., precast concrete elements, etc.). This paper will focus mainly on the design and the execution of the micropiled foundation.

Sep 8, 2021

By Brian Isherwood

TransCanada Pipelines, Calgary (TCPL) is one of North America's leading transporters of natural gas through its energy transmission business. TransCanada also operates significant complementary businesses in energy marketing and energy processing in North America and internationally. The main trunk pipeline crossing Canada comprises as many as six pipes, 30" to 48" diameter delivering up to 7.8 trillion cubic feet of natural gas per day. To maintain the maximum operating pressure of 1000 psi, it is necessary to provide compressor stations at 60 to 100 km spacing. One such station is located at Potter, in northern Ontario, some 80 km north of Timmins, referred to as Station 102. The station contains two compressor plants, 'A' and 'B' Each incorporates a gas turbine driven centrifugal compressor unit. 'A' Plant uses an aero-derived gas generator (jet engine) rated at 15 MW (19,000 HP).

Jan 1, 1997

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

By Rolf Katzenbach

The principle questions related to the design of deep foundations especially in soft soils are the stability and the cost optimised settlement reduction to prevent possible damages and to minimise the deformations of the adjacent infrastructure. The present develop­ments in the design of deep foundations lead to the design approach of the Combined Pile-Raft Foundation (CPRF) which offers a lot of new possibilities, e.g. the utilisation of the CPRF for horizontal loading or the use of the subsoil as a geothermal storage system.

Jan 1, 2006

By Osama El-Fiky

There are many types of deep foundations currently being used in the San Francisco Bay Area, one of the most common being driven precast, prestressed concrete (PC/PS) piles. PC/PS piles are frequently selected for use due to of ease of installation, availability, and relatively low cost. Disadvantages of using PC/PS piles are noise, vibrations, pollution, front-end delays due to indicator pile programs, and reduced flexibility. An acceptable alternative to driven PC/PS piles was selected for construction of foundations for the heavy housing and administrative buildings at the San Francisco County Jail #3 replacement project in San Bruno, California. The pile type selected, the Auger Pressure Grouted Displacement (APGD) pile, was chosen to reduce noise, vibrations, installation time, and cost, and to allow for greater flexibility of installed pile lengths. This paper presents a case history of the use of APGD piles that were substituted for driven PC/PS concrete piles for the subject project. Standard and quick loading pile load tests were performed to confirm adherence with the design criteria originally used for the driven PC/PS concrete piles. The APGD piles were found to increase shear strength around the piles similarly to driven displacement piles. In addition, this paper presents the methodology used in monitoring APGD pile installation.

Jan 1, 2002

By Juan M. Antorena

A dynamic testing program was performed to evaluate installation procedures, assess capacity of 610-mm (24-inch) diameter open ended steel pipe to evaluate set-up and provide minimum pile tip elevation based on the dynamic testing results. The program was performed for a marine terminal project consisting of a 570-meter (1900-foot) long, overwater railroad trestle. The project location is Santa Marta, Colombia, South America. The subsurface profile generally consisted of 4m (12 ft.) of water and soft to hard silty clays. The piles were installed to an approximate tip elevation of -22 meters (MSL). Three piles were initially dynamically monitored during installation and then later monitored during restrike driving to evaluate pile drivability and bearing capacity including time related capacity increases due to soil "set-up". Knowledge of change in pile capacity with time after end of initial driving is important for design of pile foundations.

Jan 1, 1995

By Tariq B. Hamid

Deep excavation is commonly associated with construction of different deep below-grade structural elements (e.g., basement walls and slabs, tunnels, retaining walls, tanks, utilities, etc.) Deep Excavation Retaining Systems (DERS) are required when open cuts with safe slopes are not possible. Careful analysis, design, and planning of the DERS are required to provide safe below-grade construction and secure nearby structures from damaging effects that may result from the deep excavation. Selection and design of temporary or permanent DERS (e.g., soldier pile and lagging, sheet piling walls, secant pile walls, tie backs, etc.) can have significant impact on time, cost, and performance. In order to design DERS using conventional methods, it is necessary to obtain shear strength parameters, angle of internal friction (ø), and cohesion (c), of retained soils. Residual shear strength parameters (ø'res, c'res) obtained from drained direct shear tests and triaxial tests on saturated samples have been commonly used in practice for the analysis and design of DERS. However, there are cases where ground water table remains at or below the base of excavation during the design lifetime of DERS. In such cases, the soil above the ground water table is in an unsaturated state. Therefore, it is important to account for the unsaturated conditions of soils in order to optimize the design of DERS. This paper is focused on implementing the basic concepts of unsaturated soils mechanics including matric suction and soils-water characteristic curve (SWCC) to estimate design shear strength parameters of unsaturated soils (i.e., ø°, c', and ø') for the design of a cantilever sheet pile walls, a typical case of study of the DERS. The results of this study indicate that the determination of unsaturated soil strength shear strength parameters is simple. In addition, using unsaturated soil mechanics theories has an outstanding impact on the design of retaining systems.

Jan 1, 2006

By Upendra L. Karna

The pile capacity gain with time evaluated and implemented for the construction of the Route 21 Viaduct in Newark, NJ, U.S.A is discussed in this paper. The project consisted of the replacement of more than 3.2 km of viaduct and ramps. The project site consists of thick residual materials deposited by the Wisconsin Glacier over sedimentary rocks. The upper portion is glacial-lacustrine deposit underlain by marginal morainic till and stratified drift. Subsurface investigations identified significant variations in layer thickness and grain size consistency. The site was characterized into 4 Soil types, based on subsurface soil behavior. Closed end 600 mm and 450 mm diameter driven pipe piles were used for the foundation. Loading tests conducted during an advanced construction contract, established that a significant soil set-up could be expected. For the first construction contract, a pilot loading test program consisting of 112 dynamic loading tests and 77 re-strikes (at 2 to 4 weeks) using the PDA (Pile Driving Analyzer) with CAPWAP (Case Pile Wave Analyses Program) was conducted to establish the soil set-up behavior. Nine (9) quick static loading tests were conducted to substantiate the long-term pile capacity. Based on the loading test results, average set-up factors were established and utilized for developing production pile driving criteria. Bearing resistance with depth was analyzed and reviewed. The set-up factors varied significantly, ranging from 1.05 to 1.89, and averaged about 1.30. Conclusions are derived. Set-up factors behavior for each soil type plotted by linear regression are presented and discussed. An appropriate set-up with time relationship for a glacial soil is suggested.

Jan 1, 2006

By Hou Shitao

With the development of Wuhan's city planning in China, new buildings of moderate and high store have been increasing day by day. Precast concrete piles or cast-in-site piles were used in the major foundations of the buildings. In process of their design and construction geotechnical engineers are concerned very much about practical bearing capacity and construction quality of pile foundations. In order to grasp accurately the cases static loading or vibration test is used generally to judge them. At present, the major questions in existence are that although a load is applied directly on pile and measured datums are reliable for static loading test, it must take a lot of work and longer time and engineering cost is higher. A vibration test has the advantages of which checking up of pile quality can be performed rapidly, the test is simple and convenient, and scope measured wide. But bigger error exists generally in measured datums. Therefore, it is nesessary to make vibration test on piles more perfect for pile foundation engineering. It is stated in paper that adapted technique of vibration test on piles is quite right in developmental direction sense for pile foundation. There are a great variety of vibration test methods on piles. A few of methods which often are adapted in practice can not meet the need of different practical engineering. It is also an important question whether the instruments of vibration test and relevant computer softewares make a response accurately for practical case. Different sequence of operation and technical requirements comes into being some influence directly on the test results. Meanwhile, different combination of soil stratigraphy, soil texture, groundwater and pile could cause different error of test datum. It is necessary to analyse and judge objectively the results of vibration test. Therefore, on the basis of developing and perfecting further the technique of vibration test, the applied technique of vibration test should be standardized so that better test results can be obtained.

Jan 1, 1991

By N. S. Yet

This paper shall present the design and construction of bored pile and diaphragm wall for the proposed MHA complex in Singapore. The work was carried out by L&M Foundation Specialist Pte Ltd and PWD Consultants Pte Ltd was the consultant for this project. A brief description of the project is first presented to illustrate the scope and scale of the work involved, which includes the construction of bored piles and diaphragm walls and installation of steel stanchions in the bored piles. This is followed by a description of the methodology used to analyse and design the wall and bored piles. As both towers in this project are supported on bored piled foundation and are constructed by top down construction method, the analysis of the wall has taken into consideration the sequence of work phase by phase and this was carried out by means of a commercial finite element program called CRISP. Modelling of the problem will be briefly described and the findings from the numerical analysis will be presented. This is followed by a description of the structural and geotechnical design aspects of bored piles. The paper shall then describe the difficulties encountered for this project and solution used to solve the problem. The subsoil condition will be described with special mention on the encounter of very strong granitic rock at depth above the maximum excavation level of the basement at certain locations, hence necessitating the drilling of rock for a considerable depth for both bored piles and diaphragm wall. At this juncture, the construction method used to drill through the rock will be briefly described. For construction of bored piles, penetration of rock was carried out by chiselling or drilling using reverse circulation rigs. For construction of diaphragm wall, it requires the employment of Bauer hard rock cutter which uses cutting wheels fitted with roller bits and are capable of excavating into granitic rock of compressive strengths more than 100 MPa.

Jan 1, 2000

By Yin Zongze

The pile foundation of Sutong bridge pylons is an extra large pile foundation. The length of piles is 115m, and the diameter of the piles is 2.5-2.8m. Since the traditional design method may not determine the settlement and capacity reasonably for such a large pile foundation, the finite element method is used to study stress and deformation of the foundation. The interface element is set to simulate the possible slide between piles and soil layers. The hyperbolic model is taken for soils. Parameters are determined from triaxial test first, and then modified by back analysis on basis of in-situ loading test. The computation results show that the axial force of piles changes with the location of the pile. Outer piles support greater axial force and also friction. The settlement will not be greater than 26cm. The stress and deformation of the pile cap, the abutment, are obtained too. The whole foundation is safe.

Jan 1, 2006

By Mario A. Terceros H., K. Rainer Massarsch

"ABSTRACTThe Expander Body (EB) technology has been used successfully to increase the pile toe capacity of bored piles in loose to medium dense soil. An important advantage of the EB system is the ability to monitor the EB expansion process, which provides important information regarding soil strength and soil stiffness. This information, obtained for each installed pile, can be used to determine the actual shape and pile toe area. The expansion pressure can be used to design the pile base capacity.The Expander Body system has been recently improved by incorporating the possibility of post-grouting of the soil below the expanded pile toe. This improvement measure provides additional strength and stiffness to the pile toe and reduces pile settlement.The shaft bearing capacity of bored piles can be increased by using a soil displacement auger, which avoids soil decompression and increases lateral soil stress. This paper describes the principle of the EB system. During the past 20 years, a large number of EB piles have been installed in Bolivia and elsewhere, providing a sound database. Results from field loading tests are presented. A comprehensive study of test piles with and without EB base has been carried out which demonstrates the improvement effects that can be achieved by the EB pile system and the combination with the displacement auger pile method. A design concept for the EB pile system with the full displacement auger pile is presented. A high degree of quality control can be achieved by monitoring the entire pile installation process, including the displacement pile and the Expander Body.1. IntroductionIn many regions of South America, soil deposits consist often of predominantly loose to medium dense sands and silts, often with high groundwater table. In the Santa Cruz area in central Bolivia, such soils are frequently quaternary sediments, deposited by the river Piray. The city of Santa Cruz is located at the right bank of the river.The most common deep foundation method during the last 30 years has been cast in situ piles, augered and concreted under support of bentonite slurry. The design of such piles has been based on SPT results. However, SPT is often performed without quality control and the reliability of geotechnical data is therefore often poor. Traditional methods of pile installation with simple well drilling equipment of insufficient capacity are frequently used. Such methods lack basic requirements of quality control. Such piles have usually low toe resistance and work mainly by shaft resistance . Although the construction process and materials are cheap, the final product has variable and limited capacity. However, the most serious deficiency is that actually achieved pile capacity and pile settlement can be erratic and difficult to predict, leading to uncertainties with regard to actual foundation performance."

Jan 1, 2014