Search Documents

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

By Junhwan Lee

Pipe piles can be either closed- or open-ended piles. Pile load capacity for a closed-ended pile consists of the shaft and base resistances, while, for an open-ended pile, it consists of shaft, soil plug, and annulus resistances. In order to investigate the pile load capacity of both closed- and open-ended piles, two field pile load tests were performed. For the open-ended pile, the fully instrumented double-walled system was used to separately measure all the components of the pile load capacity. The soils at the test site were predominantly granular soils with relative densities varying from loose to dense with increasing depth. The incremental filling ratio (IFR), which affects significantly the load capacity of open-ended piles, was also measured during pile driving. The test results indicated that the total load capacity of the closed-ended pile was higher that that of the open-ended pile, mostly due to the difference in shaft capacity. The shaft and base load capacities of the open-ended pile were 44% and 20% lower than the corresponding values for the closed-ended pile.

Jan 1, 2003

By J. Tanner Blackburn, James R. Gingery, Lisheng Shao

Rigid inclusions consist of grout columns installed using displacement auger or vibrated tooling. The columns are typically installed in an array to provide support for footings, mats, or embankments. Due to the relative small column diameter and low replacement ratio, the surrounding soils typically have minimal densification or improvement. A gravel load transfer platform is commonly used above the rigid inclusion head to distribute stresses more broadly to the supported structure. The axial stiffness and geotechnical engineering mechanics of rigid inclusion design are similar to those of deep foundation systems, but they are typically only lightly- or un-reinforced and are not structurally connected to the above-grade structure. The popularity of rigid inclusions is increasing in the Western U.S., where many urban areas are subject to moderate to high seismic hazard levels. However, the performance of rigid inclusions under seismic loading is poorly understood, and seldom addressed in current designs. The elements are brittle, with limited or no ductility and relatively low moment capacity, and therefore may be prone to damage under seismic loading. Three modes of seismic loading should be considered: inertial loading from the structure, kinematic loading from vertically propagating shear waves, and kinematic loading from ground failure- related permanent ground deformation. This paper focuses on the first two modes. A simplified procedure for evaluating kinematic and inertial loading of rigid inclusions is described, and its use is illustrated through application to a site in Southern California. The results show that moderate to severe kinematic loading can generate plastic hinges in the rigid inclusions. Engineering consequences of this hinging could include settlement or bearing failure. INTRODUCTION In this paper the term ‘rigid inclusion’ (RI) refers to grout or grouted aggregate columns that are installed using either drilled or vibration displacement techniques. They are commonly installed in arrays to support vertical loads from footings, mats, or embankments. RIs are not structurally connected to footings they support. Rather, it is typical for a dense gravel load transfer platform (LTP) to be installed as a cushion between the RI head and supported footing or new fill. In cases of RI support of fill embankments, the LTP may be reinforced with horizontal layers of geogrid.

Jan 1, 2018

By Q. M. Huang

In 1979 our company undertook the project of infra-structural work of White Swan Lake Hotel, (International class ) Guangzhou. Visit to the site showed that it was situated at the riverside, covering an area of 54,000 M2 with 30,000 M2 of which reclaimed from Pearl River. The material used for reclamation was black sand which was dredged from the nearby riverbed. The sand had the properties of high permeability and very low internal friction. The basement of the building was 6.2 m below ground level and 3 m lower than the riverbed. Apart from the pile foundation, a diaphragm wall was to be constructed prior to the commencement of excavation work for basement. A feasibility study was carried out to determine the method of construction which would maximize utilization of the plants and equipment that were available in the execution of the aforesaid foundation works. This report concerns only the construction of the diaphragm wall and the performance of the plants employed. A detailed delineation of the construction method is herein discussed

Jan 1, 2010

By James J. Anderson

In this talk I will report on an effort to reassess the risk of pile driving to juvenile salmonids migrating through Puget Sound. The study was motivated by the concern of the construction industry that provisions restricting pile driving during the spring migration is resulting in an unbalanced burden to the industry. In simple terms the industry wants to know if some construction can be conducted in the spring without harming the juvenile fish. Fisheries agencies have agreed to reconsider their regulations in the context of additional studies. So, in this talk I will present some thoughts on risk assessment in general and the results of our study to assess the impact of pile driving on Snohomish River juvenile pink and chum salmon that migrate through the Navy Homeport construction site at Everett. The research, which is being carried out by the Fisheries Research Institute at the University of Washington, was planned and is supported in a joint effort including: the Washington Department Fisheries, National Marine Fisheries Services, U.S. Fish and Wildlife Service; General, Manson, and Hurlen construction companies, the Department of Transportation and a number of Puget Sound ports authorities. I will first briefly discuss the early life history of the juvenile salmon the regulations are designed to protect Second, I will outline the legal criteria required for risk regulation and some specific thoughts on how a reassessment of pile driving risk might be approached. With this basis I will report on our research and how it can be applied to a new risk assessment.

Jan 1, 1990

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

By Benoit Virollet

Over the last 10 years the diameter of unbraced, unlined and unanchored circular shafts has grown dramatically in many parts of the world. This progress has taken place through improvements in: construction methods; concrete rheology; and design capabilities. Excavation equipment has become more precise in terms of operator control and ability to correct alignment of digging elements leading to better alignment tolerances. Also contributing to the increases in shaft diameters is the evolution of design models. A better understanding of soil structure interaction is being incorporated into the analyses in terms of radial soil stresses and imposed loads on the shaft. This paper provides an overview of the recent progress made in circular shaft construction, the primary design considerations, and some innovative uses of efficient arc elements to develop unsupported structures of other shapes. In addition, a summary of recent circular shafts constructed worldwide is provided.

Jan 1, 2006

By Ramon Varghese, A. Boominathan, Subhadeep Banerjee

Pile raft foundation system has been accepted as an economic foundation design for high rises and heavily loaded structures. Seismic response analysis of PR foundation systems involves complex pile-soil-pile interaction as well as raft-soil-pile interactions, for which simplified methods have limitations. Kinematic rocking of a pile group is known to be influenced significantly by the pile configuration. The presence of an embedded pile cap, or a raft, as in the case of a piled raft can further alter the dynamic characteristics of a pile group-soil system. In the present study, frequency dependent kinematic response factors are evaluated for piled raft foundation, using the substructuring approach based ACS SASSI program. Performance of the numerical analysis methodology is first evaluated with results from analytical and experimental studies reported in literature. The effect of pile layout on kinematic response is then studied for a piled raft in clay system based on a centrifuge shaking table test reported in literature. Kinematic response factors and horizontal impedances were determined for varying pile spacing ratios. The influence of raft has been found to increase kinematic translation by up to three times in the piled raft in clay system. Pile configuration is found to play a significant role in kinematic rocking of piled rafts. The presence of raft is observed to significantly reduce dynamic rotational stiffness coefficient in the dimensionless frequency range of 0.23 to 0.6, and increase damping coefficient after a dimensionless frequency of 0.4, for all pile configurations studied. The effect of an embedded raft is hence an important consideration while evaluating foundation input motion as well as impedances of piled raft foundations. INTRODUCTION The Piled raft foundation (PR), is a composite foundation system that facilitates load sharing between pile and raft. It is an economic foundation option for high rises and heavily loaded structures. Soil structure interaction (SSI) in PR system involves raft-soil-pile, and pile-soil-pile interactions which needs to be considered in static or dynamic SSI analysis. The effect of pile can have substantial influence on foundation input motion, for seismic analysis (Di Laora et al. 2017). Piles are observed to depress a wide spectrum of the seismic excitation (Fan et al., 1991, Di Laora & de Sanctis, 2013). Although kinematic response of pile groups have been extensively studied in the past, the influence of the presence of raft on kinematic response characteristics of pile groups has not received much attention.

Jan 1, 2018

By Johannes Labenski, Christian Moormann, Johannes Aschrafi

"Open steel pipe piles are used for various applications in costal engineering, port structures and increasingly important for offshore structures. During the installation of open steel pipe piles the formation of a plug has an influence on the installation process of the pile and also on the final bearing capacity. The formation of the plug depends on different factors, e.g. the pile diameter and the installation method. This paper starts with a structured overview about analytical methods (API, EAP-EAU, UWA-05, HKU-12, Modified API) to calculate the axial bearing capacity of open steel pipe piles. The numerical simulation of the installation process of open steel pipe piles has to fulfill high demands, i.e. to accurately represent the penetration of the pile inside the soil, the formation of the plug and also the stresses and strains during the installation. A numerical back analysis of a comprehensive field test, using the Coupled Eulerian-Lagrangian (CEL) method and a hypoplastic constitutive model for sand, reveals the stresses and displacements of the soil and of the piles. The analysis provides a comprehensive understanding of soilpile interaction.INTRODRUCTIONThe particular difficulty in the numerical simulation of plug formation, is that the effect of plugging inside open ended steel pipe piles has not been fully investigated. In scientific papers different approaches are documented to explain this phenomenon. Some are based on in-situ tests and others are based on numerical simulations. One of the challenges is to determine the end bearing capacity and shaft friction of the steel pipe pile. Different approaches have been developed over the years to determine them e.g. from Randolph et. al. (1991, 1994) and Paik et. al. (2003). Recent approaches are the ICP-05 Method (Jardine 2005), the UWA-05 Method (Lehane 2005) and the HKU-12 Method (Yu & Yang 2012a). A comparison of some methods can be found in Schneider et al. (2010). A plug inside an open steel pipe pile can be visualized as a spatial bracing of soil between the inner surfaces of the pile, cf. Lüking (2010).. However according to Lüking & Kempfert (2012) this bracing only exists for the height in the end of the pile equal to twice its diameter.To identify a plug inside a pile, there are different measurable parameters. One parameter is the development of stresses around the pile during and after its installation. Henke (2013) measured the inand outside horizontal stresses at the pile tip during the installation. The results showed higher stresses on the inside compared to the outside. To validate his measurements he performed a numerical back-analysis of the measured installation process and got matching results."

Jan 1, 2017

By John J. Vieaux

Allowable loads on Dynamically-Cast-In-Place Piles (the Franki type) can be correlated with N values from the Standard Penetration Test. Using a constant developed by Nordlund, a conservative value for load-carrying capability of a DCIP pile is developed. The DCIP pile and method of installation is briefly described.

Jan 1, 1984

By N. Shariatmadari

Two dry docks are currently under construction on the northern banks of the Persian Gulf by Iran Shipyard and Offshore Industries Co. (ISOICO). The construction of these dry docks forms a huge civil offshore project. The foundation system include more than 6500 large diameter (40-48 inch) spiral pipe piles with embedded depth varying from 18 to 25 meters. Extensive geotechnical subsurface investigations were carried out in the project site in order to provide enough information and proper perspective on the underlying soil layers. The results of geotechnical investigation indicated that a 20 m thick dense silty sand layer exist which can be considered as the main bearing stratum. Due to short clear distance between the piles (less than 3 m) refusal occurred for some piles, accordingly led to actual length less than their design length. To verify and in-situ evaluation of piles capacity, static and dynamic full scale loading tests programme were performed. The data from 40 static compression and tension and also 50 dynamic tests with PDA were interpreted and analyzed by current approaches and CAPWAP software. The results of analysis demonstrated that the safety factor of bearing capacity of piles must be increased to reach a safety factor of about 1.8. To achieve this purpose the interaction of combined piled-raft system has been realized.

Jan 1, 2007

By Cory J. E. Yacyshyn

Anchored steel pipe piles are being used more frequently in British Columbia for shoreline projects such as public ferries, cruise ship docks, containership terminals and locally in the expansion of the Vancouver waterfront convention center. While a 36? diameter driven pile may provide adequate compression loads it will not always achieve enough penetration to provide the required tension loading. That is why bundles of threaded anchors or strands are drilled through the center, past the pile tip, and anchored into the underlying strata. Drilling up to 250 feet deep through the piles in variable water bearing strata presents challenges. Southwest Contacting Ltd. (SWC) recently completed the three largest anchored pile projects in BC; Vancouver Port and Convention Center Expansion, Vanterm Container Terminal and the new Prince Rupert Cruise Ship Terminal. This paper will present the separate challenges encountered drilling the anchors. At Prince Rupert, the recently completed Northland Cruise Ship Dock ultimately required a cased system to drill and install triple thread bar anchors. When 200 foot long steel pipe piling was unable to penetrate the highly fractured gneiss/schist bedrock to obtain a seal and consolidation grouting was unsuccessful, a modified cased system was advanced deep enough into the rock to eventually seal. The 3-#20 bars were changed to 12-strands since the bars wouldn?t fit through the smaller cased hole. The options were limited because each dolphin only had enough room for a small hydraulic drill rig that wouldn?t have the power to fully case the holes. The Canada Place Pier Extension in Vancouver?s Harbor led to the development of an innovative tip design used later at Vanterm. The 36? diameter steel pipe piles were driven closed end but modified to permit drilling through a concrete plug at the base. The driving of the piles at Canada Place often knocked out the plug so we were faced with 50 feet of sand up inside the pile when the drilling started. This led to discussions on how to safely remove the sand, solidify the tip, and continue drilling to get past the tip without undermining the pile. Finally, Vanterm Berth Extension was completed with a unique drilling system because the pile tips stopped in hydraulic sands, as opposed to the native till. We were faced with advancing the casing to the till without undermining the base of the pile. With 100 psi water pressure at the pile base after we broke through the concrete plug, the trick was to prevent charging the sand with our 250 psi air which liquefies it and forced it up our drill casing. And of course, it has to happen just before Christmas holidays!

Jan 1, 2004

By Paul J. Axtell

Self-hardening cement-bentontie (c-b) slurry walls were constructed as shear walls to stabilize the downstream slope of Tuttle Creek Dam near Manhattan, Kansas. The slope stabilization was required to protect the existing pressure relief well system located at the downstream toe of the dam. The wells require protection from slope deformation induced by liquefaction of the foundation sands during or immediately after the design seismic event. The shear walls are transverse to the axis of the dam, unreinforced, and relatively brittle members that may be exposed to relatively large shear strains, and possible cracking, during or immediately after shaking. An extensive laboratory investigation was conducted on recovered core samples to optimize the mix design and stabilization scheme. Furthermore, as is the topic of this paper, a portion of the laboratory investigation was to determine the large-strain, or post-peak, shear strength of the c-b material for use in limit-equilibrium slope stability analyses and numerical deformation modeling to assess the magnitude of permanent deformation caused by the design earthquake. These data may be beneficial to other projects that are considering the use of unreinforced c-b slurry walls for seismic retrofit purposes.

Jan 1, 2010

By Shinji Sassa, Naoki Takahashi, Eiji Kohama, Wakaki Tsuda, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"Abstract Deep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. Column-type solidification, however, has been thought to have little effect as a liquefaction countermeasure, because the shear deformation of unimproved soil between the columns cannot be reduced. In recent years, experimental results have been reported that imply that solidified columns can reduce the shear deformation of unimproved soil around them. A new arrangement has been proposed to mitigate lateral flow induced by liquefaction. In this study, a series of dynamic centrifuge model tests was conducted to verify the lateral flow resistance of stabilized columns. The results indicate that stabilized columns can reduce the lateral flow of liquefied ground if the column displacement and the column head rotation are restricted. This paper concludes that it is important to restrict the displacement and the rotation of the column head by surface improvement to mitigate the lateral flow of liquefied ground.INTRODUCTIONDeep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. The solidified body formed by the deep mixing method is usually block or lattice shape, composed of solidified columns that overlap each other horizontally. Lattice-type solidification has been shown to be effective as a liquefaction countermeasure despite the presence of unimproved soil inside the lattice wall, because the shear deformation of the interior soil is restrained by the wall (Suzuki et al., 1989). On the other hand, it has been thought that column-type solidification cannot reduce shear deformation of unimproved soil around columns, because the displacement of a solidified column is less restricted than that of a lattice wall. Column-type solidification has been reported to have little effect as a liquefaction countermeasure, but to be superior in terms of construction cost and applicability around existing underground structures (Koga et al., 1986). However, there are experimental results implying that solidified columns have reduced the shear deformation of unimproved soil and mitigated its liquefaction (Yasuda et al., 2003; Tanaka et al., 2003). Yamamoto et al. (2006) conducted dynamic analyses of ground improved with lattice- and column-type solidification. Their results showed that column-type solidification with an improvement ratio of more than 35% reduces excess pore water pressure generated by earthquakes. Furthermore, the new column arrangement shown in Figure 1(a) has been proposed to mitigate lateral flow induced by liquefaction. It was developed and has been verified using dynamic model testing in a 1 g field (Takahashi et al., 2010a; 2010b; 2013; Towhata et al., 2010). The stabilized columns in this configuration interrupt lateral flow in any direction, unlike those placed in square and triangular arrangements."

Jan 1, 2014

By Lawrence F. Johnsen

In 1989, the Connecticut Department of Transportation authorized the evaluation and design for a reconstructed Route 1 bridge over the Quinnipiac River in the City of New Haven, Connecticut. The project extends from the intersection of Route 1 with East Street, easterly for approximately 3/4 mile to the intersection of Route 1 with Wheeler Street and Stiles Street. The reconstructed roadway will be relatively on-line and widened to provide for four lanes of vehicular traffic and a single-track railway line. The existing bascule bridge and approach spans, which were constructed in 1924, will be replaced by a 270-foot span lift bridge and new approach spans. The lift bridge will have a main lift span weighing approximately 3000 tons, second largest after the Burlington Northern Bridge over the Williamette River in Portland, Oregon. The new bridge will widen the navigation channel to 24 0 feet and provide vertical clearances of 13 feet when closed and 62 feet when open. The project is located in an industrial area. Adjacent properties include retail gasoline sales, auto repair, railroad transport and bulk storage of petroleum. Existing structures include the Yale Boathouse and several retaining walls serving as containment dikes for petroleum storage tanks. The Yale Boathouse, located on the east bank of the river, was constructed in 1909-1910 and is eligible for listing in the National Register of Historic Places.

Jan 1, 1993

By Geoffrey D. Collins

This paper deals with the construction of the Effluent Outfall Diffusers which form part of the outfall for the Deer Island sewage project. The work was executed 15 km out to sea in Massachusetts Bay and required the drilling, installation, grouting and accurate determination of the actual position of 55 riser shafts in 33.5 m deep water. Although not strictly a "foundation", the contractor's approach to the installation of the diffusers was a logical development from many marine foundation projects executed by the Contracting companies over the last decades. The only previous application of this design of outfall had been in Australia where offshore oil drilling techniques had been adapted for use in riser installation.

Jan 1, 1994

By Walter I. Paniagua

Drilled shafts and precast concrete piles were installed for the foundation of several structures in a reconfiguration project of a refinery in Minatitlan, Veracruz, in the Gulf of Mexico. The soils are alluvial deposits of flat land from the Coatzacoalcos River, which are embedded with layers of sand, soft clay, and peat. As part of a QC/QA program, load tests, both static and dynamic, axial and lateral, were performed. In this paper results of 32 axial tests are presented, in which typical load-displacement curves were measured at the top of the foundation elements; from the interpretation of these plots, data were recorded for ultimate side shear and in some cases for end bearing capacities, which are compared with the theoretical results of the final stage of the foundation design. The comparison shows that under allowable loads, side shear determines the bearing capacity of piles, even when the tip is embedded in a hard layer. Underestimation of the side shear is evident; therefore design criteria, as well as the methods used for obtaining soil parameters, should be reviewed.

Jan 1, 2007

By Matthew Janes

Quality control procedures are increasingly important with today's higher capacity foundations and complex loading conditions. The need for a mobile, repeatable, nondestructive and economical load test method led to the development of an entirely new approach. The system described involves using solid propellant fuels to accelerate a reaction mass off the test pile. The force required to accelerate the reaction mass upward acts equally downward on the pile. Very high forces may be applied to the pile in a controlled, linearly increasing manner. The duration of the applied load is approximately 100 milliseconds. This rate of loading is slow enough to allow the pile and soil to react together as a composite rigid body. Pile/soil accelerations and velocities are low, typically 1 g and 1 m/s respectively. The effects combine to produce pile and soil response no longer dominated by the transfer of force via stress pulse (as with impact). Instead the pile force increases throughout the length of the pile, with pile top and toe stresses building in unison with time. This emulates the stress condition during static pile loading. Finally, state of the art instrumentation systems are used to obtain test data. Displacement is monitored directly using a laser datum and integrated receiver located at the centre axis of the pile. Force is also monitored directly using a calibrated load cell. Data is acquired and digitized using a 386 PC with user friendly software capable of producing load deflection curves and time histories in the field seconds after testing.

Jan 1, 1990

By P. V. Chandramohan

"In ports, piled berths are designed and constructed for berthing of ships with a finite draught. Piles in a bridge foundation also have a large free stand above scoured level. The piles of these structures have to withstand large horizontal forces imparted by the impact of the approaching vessels or due to longitudinal and transverse action in a bridge. It is also imperative that these piles have to project out of the dredged / scoured bed. These piles are normally designed as slender compression members subjected to bending also. They are subjected to vertical load tests for assessing the soil resistance. Lateral load tests, as a rule, are also stipulated. IS and IRC codes stipulate a deflection criteria for lateral load test to arrive at the capacity. These tests are usually conducted on a working pile by jacking out two piles. At the time of the test, pile will be free headed. But in service, piles are fixed head. There is a large difference in deflections between a fixed head and a free headed pile. Besides, a free headed pile will be subjected to a much higher bending moment than the fixed head one. This will put the working test pile under risk of breaking during the test. The problem is analyzed with case studies. INTRODUCTION Vertical capacity of piles is assessed by static formulae. This formula is based on the soil properties obtained from random soil exploration and laboratory and in-situ testing. Since soil is not a homogeneous medium, properties can vary. The design parameters taken for computations may be different from the ones at the interface of the pile with the soil. The best way is to find out is by a load test. The code IRC:78-2014 has rightly stated that initial load test is part of the design process. This is true with the vertical load test. But there are certain problems with the purpose and inference of the lateral load test. In both the tests the criteria for acceptance is the quantum of movement of the point of application of the load. In the former, the movement is vertical and depends more on the compression of the soil than the compressive strain in concrete. But in the latter, this movement is partly on account of the flexural rigidity of the pile and partly due to the horizontal compressibility of the soil. The role of rigidity of the pile is more when compressibility of the soil is higher. Lateral load test is done by jacking one pile against another because it is difficult to get an independent horizontal reaction. Please see Fig.1 Photo."

Jan 1, 2015

By Joseph C. Gillen

This paper discusses the design, construction, and performance of the support of excavation system used at The Atlantic Building jobsite. The support of excavation system had to be adaptable to the different conditions surrounding the site. These conditions included support of four historic building façades, including the nine-story Atlantic Building, as well as support of three historic row-houses along two walls. Directly adjacent to the site is the historic Ford?s Theatre and townhouse. Across a 15? alley is the American Immigration Lawyers Association (AILA) Building, and across a 30? alley is the Federal Election Commission Building and another ongoing excavation. Of historical note, these two alleys were the escape route for John Wilkes Booth following his assassination of President Lincoln. With the excavation being 53? to 58? deep, the system included driven and drilled soldier piles, drilled bracket piles, and two modified tangent walls. The bracing included tiebacks, corner braces, wales, cross lot struts, and a specially designed support system for the nine-story façade. The footprint of the excavation included 12 corners and all alleys and streets were to remain open during construction. The performance requirements for system movement at Ford?s Theatre and AILA Building were ½ inches in the horizontal direction. The modified tangent walls were used in these areas to provide stiffness. The soil conditions at the site were fill material on top of a shallow, sandy, silty, gravel layer on top of a deep layer of soft organic silt and clay. Below the silt and clay layer was fine sandy material at the subgrade.

Jan 1, 2006