Search Documents

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By R. Lee Wooten, David R. Shields, Darren D. Clark

"Borehole permeability tests that measure flow or head changes in boreholes located within seepage barrier walls are commonly used to estimate the in situ permeabilities of those walls for quality control and assurance. The current state of practice for estimating permeabilities from these barrier wall borehole tests is to use equations published by M. J. Hvorslev in 1951. Hvorslev’s borehole test equations model an infinite stratum of uniform permeability, which is not the actual condition for a test performed in a low permeability barrier wall located within a high permeability stratum. We examine and develop alternative equations based on line source analytical models, which more closely match barrier wall test conditions. We describe how these alternate equations can be used to estimate barrier wall permeabilities from borehole tests and compare the results to those obtained from the Hvorslev models. We also provide recommendations that consider differing upstream and downstream water levels.Barrier Wall Permeability Tests - State Of PracticeThe installation of seepage barrier walls has become more common in a variety of applications ranging from dams and levees to contaminated sites requiring retardation of groundwater flow. The types of seepage barrier walls and installation methods include soil-bentonite, soil-cement-bentonite, concrete, self-hardening slurry, geomembranes, and sheet piles, installed with various soil mixing, slurry-supported trench, and driving methods.Owners and contractors have used a variety of methods to evaluate the permeability of these seepage barriers. The following table lists commonly used quality control/assurance tests for evaluating the permeability of a seepage barrier."

Jan 1, 2016

By Shawna Munn, Sarah Speir

Cedarvale Station is one of 25 new Eglinton Crosstown light rail transit (ECLRT) stations along Eglinton Avenue in Toronto. It is an interchange station with the existing Toronto Transit Com- mission (TTC) University subway line and is located at the intersection of two major thoroughfares. The new LRT tunnels run below the existing Yonge Spadina subway line and required total excavation depths of 20 m (65 ft) to facili- tate construction of the new station.

Jan 1, 2023

By William F. Anderson

A series of pile load tests (maintained load tests, constant rate of penetration tests at different rates, and statnamic tests) was carried out on an instrumented model pile installed in clay beds prepared by consolidation of a slurry in a calibration chamber. The total load, shaft resistance and end bearing during the pile load tests were investigated. Following this, alternative methods of deriving the static load-settlement curve from a Statnamic test in clay taking into account damping effects have been proposed. These methods have then been used to interpret a statnamic test on a full size instrumented pile installed in a stiff glacial till.

Jan 1, 2006

By Sushant Upadhyaya, Deniz Karadeniz, Ahmed Mohamed

Soil setup analysis provides opportunities for efficiencies in pile foundation design and installation. Soil setup gain with time was evaluated as part of the foundation design and installation for twelve bridges along the Interstate 64 corridor between York County and Newport News in Virginia. The substructure elements of the bridges consist of driven precast prestressed concrete piles or H-piles. This case study describes lessons learned to understand the soil setup phenomenon during the installation of the piles in coastal plain. We were able to make expedited decisions during construction by analyzing previously performed pile dynamic analyzer (PDA) test results within the project alignment. Data evaluation included analyses of PDA data obtained from initial driving and restrike after a few hours to 5 weeks. The test data showed pile resistance increase up to twice in most cases and as high as four times in some cases. Foundation design and acceptance based on soil setup can provide opportunities for cost savings and advanced scheduling during construction.

By Diane Reid, Antonio Marinucci, Robin Mao

Super Cells are an innovative, open-shaped bi-directional static load testing device used to promote concrete flow during placement while utilizing greater cross-sectional area of the pile to achieve large applied axial loads at relatively low hydraulic pressures (≤ 250 bar). This paper describes the results of multi-level load testing performed on a sacrificial drilled shaft that was 3.8 m (12.7 ft) in diameter and 110.6 m (363 ft) in length for the Jiaxing-Shaoxing River Crossing Bridge that spans Hangzhou Bay in Shaoxing, China. The test shaft was instrumented with embedded strain gauges and telltale rods along with displacement transducers at the top of the pile to measure the load-induced displacements along the length of the shaft. Load testing was performed twice using a Super Cell placed near the tip of the shaft, prior and subsequent to tip post-grouting, and then again using a Super Cell placed higher in the shaft. The axial resistance for the tested conventional drilled shaft was more than 5 times greater than the estimated axial resistance. In addition, the axial resistance after tip post-grouting (347,100 kN (39,033 ton)) was about 5.3% greater than the ungrouted axial resistance (329,600 kN (37,050 ton)). INTRODUCTION During the past few decades, the magnitude of axial, lateral, and flexural loading has considerably increased due to updated design codes, larger superstructures, and the manner in which extreme event loading (e.g. seismic and scour) is incorporated into design. The diameter and depths to which bored piles or drilled shafts are constructed have increased considerably during the last three decades due to the advancements in equipment technology and capabilities. In addition, monoshaft foundations have become increasingly used, as one large drilled shaft is able to replace a group of smaller diameter piles connected by a cap. Correspondingly, adequate strata, for both side and end resistance, must be discovered/determined as well as achievable to be able to construct the required foundations to support the greater design demands. As design demands have increased, the need to ensure integrity, quality, and performance of a constructed drilled shaft has become ever more crucial. Load tests are essential to validate design assumptions of side and end resistances, to assess the behavior and load transfer characteristics of the constructed drilled shafts, and to evaluate construction methods. Load tests utilizing a bi-directional static load testing (BDSLT) device can achieve considerably large applied axial loads and can be performed more economically, in less time, and in a much safer manner than conventional top-down static load testing methods.

Jan 1, 2019

By D. Cantali

This paper will be presented in two parts. The first part will present the latest advancements in pile installation techniques using state-of-the-art press-in piling technology by Giken. By pressing in sheet piles and large modulus contiguous steel tube pile walls – as opposed to the more traditional installation methods using percussive hammers or vibrators – retaining structures can be constructed effectively noise and vibration free. For over water and coastal projects with limited access, this provides significant environmental benefits in the form of minimising the construction foot print and the impact to surrounding communities and the marine natural habitat. Typical noise and vibration data will also be presented. The second part of this paper will review the current manufacturing techniques for sheet piles and introduce innovative new materials used in the current piling market for embedded sheet pile walls. Materials include long service life non – ferrous materials such as new age plastics and fibre reinforced polymer piles. Their excellent long term performance and durability make them an effective solution in the marine environment. For steel piles, a number of steel grades with reduced corrosion characteristics will also be discussed including a newly developed steel to combat corrossion in the low water zone, an area often exhibiting the highest moments in a retaining wall. A number of project case studies will also be presented to reinforce their relevance in today’s changing construction landscape.

Nov 1, 2022

By Jewels Stover, Charles A. Luxford

Oklahoma City is undergoing a replacement program for an existing 66in (1.675m) water pipeline that conveys raw water from Atoka Reservoir to the City. This pipeline currently crosses the Canadian River on elevated piers and is subject to flood hazards. To replace the existing pipeline and mitigate flood damage concerns, two parallel microtunnels will be constructed below the river channel. Access is from construction shafts located near the midpoint of the tunnels; opposing drives are launched from each shaft. This geometry dictated shafts of significant depth – exceeding 120 ft. (37m). To accommodate the casing pipe segments and microtunneling machines, a minimum shaft diameter of approximately 34 ft. (10.4m) was required. Due to the difficult geologic setting, a reinforced secant pile compression ring is specified by contract in the top 70 ft. (21.3m) of these construction shafts to provide a very low permeability support system.

Sep 8, 2021

By Mihir B. Roy

"Coal transported by rail for Thermal Power Plant in Haldia, West Bengal, India, was to be received and stored in Coal Complex comprising of Wagon Tippler, Track Hopper, Junction Houses and network of horizontal and inclined tunnels. The site was very soft with high ground water level. Deep excavation and dewatering posed great difficulty. Original plan was to drive about 1000 m of steel sheet pile and well sinking which had major impact on cost and time. High ground water was identified as the main problem. Controlling water level and maintaining it would allow open excavation over major areas. Scheme for lowering aquifer with one and two-stage well-point dewatering system was developed following basic principles of groundwater and seepage. Arrangements of wells, installation and pumping were worked out in detail. Water levels could be lowered below bottom levels of excavation. Design of sheet pile was modified under lowered ground water condition. Overall length and depth of sheet pile were reduced drastically. Open excavation was possible in segments over major areas. The scheme was highly successful in smooth and fast progress of underground works. The works were completed safely months ahead of schedule time and with significant saving in cost.INTRODUCTIONThe Coal Receiving Complex of thermal power plant comprised of 250 m long 8 m deep Track Hopper (TH), 12 m deep Wagon Tippler (WT) with provision for addition of another Wagon Tippler. Track center lines of TH and WT were very close. Coal unloading facilities were connected with a network of underground tunnels and Transfer Points (TP) upto Pent House (PH). The facilities were optimized in a compact layout within about 400 m x 120 m area. Initially excavation for TH was started adopting side slope of (1 V : 1.5 H) with 2 m wide berm and dewatering by in-pit sump and pump. When depth of excavation reached about 5-6 m, failure occurred over a long stretch as shown in Figs. 1a - 1b photos. Further work was stopped to develop scheme for carrying out deep excavation and civil works safely."

Jan 1, 2015

By Dennis J. Riley

A. This outline addresses what a sub-contractor, or a subsub-contractor should do to get paid in the event the general contractor or building owner files for bankruptcy. B. Negotiating payment terms. Progress payments vs. "pay when paid". How a sub or subsub can avoid financing the contract. C. Court interpretation of "pay when paid" clauses allow postponement not excusal of payment. See, e.g., Seal Tite Corporation v. Ehret. Inc., 589 F. Supp. 701 (D.N.J. 1984) (where the court held that the general contractor could not delay payment indefinitely to the subcontractor in the event of non-payment from the owner); United Plate Glass Co. v. Metal Industries. Inc., 525 A.2d 468 (Commw. Ct. Pa. 1987) (where the court held that payment from owner was not a condition precedent to paying subcontractor but instead a timing mechanism indicating when payment should be made); But see. Straham v. Landis Construction Co., 499 So. 2d 417 (La. App. 4 Cir. 1986) (where the court strictly interpreted the "pay when paid" clause).

Jan 1, 1991

By Jamey Rosen, Georgette Hlepas

Verticality data collected from panel and pile elements of seepage barrier walls describe the shape and position of those elements in three dimensions. These data are used to determine if a barrier wall is constructed as designed and if it meets the owner specifications with respect to tolerance (i.e., if each element is sufficiently close to vertical) and overlap (i.e., do adjacent elements overlap sufficiently to prevent leakage). Contractors use verticality data to confirm that their work matches the design, and owners use verticality data to verify the contractor’s work and confirm that specified criteria were met. Project Information Management Systems (PIMS) technology has been applied to the management, visualization, and analysis of verticality data. This paper will provide examples of how contractors and owners have used a PIMS to compile and synthesize data collected during excavations (e.g., from Cutter Soil Mixer and Hydromill drill rig telemetry), and from measurements of completed excavations (e.g., using the Koden ultrasonic tool), and used those data to model excavation geometry. We will present case studies of using these models to estimate backfill placement volumes, and to evaluate the verticality tolerance and overlap between elements.

Sep 8, 2021

By Vishal Pathak, Shailesh A. Godhuly

Ground Modification System in terms of Jet Grouting for soil strengthening and mass stabilization was engaged for a power plant project in an international power project, engineered by L&T-S&L. The site Geology consist of cohesionless type of sandy alluvial deposits (silty fine sand) as the main formation. Ground water table is encountered at shallow depth. Geological interpretation is done using soil investigation data along with CPT’s. This paper discusses design and implementation of jet grout technique to improve the mechanical behaviour of soil. To distribute load evenly from superstructure, a layer of growmast (drainage blanket) is laid above jet grout columns. Settlement evaluation is done using Finite element analysis with Plaxis 2D and Settle 3D. In the project, selected equipment foundations are resting on jet-grout columns including vibratory equipment like 144MW Gas Turbine etc. The project has been commissioned in September 2021 and operating with full capacity.

Sep 1, 2022

By Eric S. Lindquist

Two microtunnel access shafts were constructed using the Cutter Soil Mixing (CSM) method in the San Joaquin Delta region of California, east of San Francisco. Unlike conventional slurry walls and diaphragm walls that utilize concrete, soil mixing relies on blending the soils in situ with a cement slurry to create a soil-cement wall. Cutter Soil Mixing technology utilizes two sets of vertically mounted cutting wheels rotating about a horizontal axis to produce rectangular panels of treated soil. Overlapping of the soil mixed panels enabled the construction of two circular shafts. CSM panels were constructed to a depth of 29 m (95 ft) for the microtunnel jacking shaft and to a depth of 19 m (63 ft) for the microtunnel receiving shaft. The site presented several challenges, including the high depth of treatment, the variable nature of the alluvial soils, and the high water table. This paper describes the CSM technique and presents the design, construction, quality control measures and advantages of using this method for this project.

Jan 1, 2010

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By Nasr Sheta

"After Hurricane Sandy, the stability of an earth slope in the Atlantic Highlands, New Jersey in the United States was deteriorating due to slumping soils and erosion from flooding. A slope stability evaluation indicated the slope did not satisfy the requirements of the local building code. A triple-tier, pile-supported and mechanically stabilized earth wall was designed and constructed to stabilize the slope. The construction was planned from a 3-m-wide roadway and, because of rough terrain and limited work space at the site, a cast-in-place drilled-pile construction was deemed impractical due to slow pile production. An alternative procedure was utilized by pre-drilling holes, and installing precast tip-and-shaft-grouted (PCTSG) piles, which extended to competent soils to improve slope stability. A grade beam, connecting the PCTSG piles along with soldier beams and concrete lagging were used to form the lowest tier of the slope stabilization, while the middle and higher tiers were built as mechanically stabilized earth. The stability of the proposed stabilization was analyzed using 2-D non-linear finite elements. After construction, monitoring of the wall continued for about 8 months to check its performance, and indicated lateral and vertical wall movements were less than 25 mm and 6 mm, respectively, indicating effective slope stabilization.INTRODUCTIONStabilizing earth slopes using piles to connect near-surface unstable soils to underlying stable ground masses has been investigated by many researchers, who presented various approaches to evaluate the contribution of the pile system towards improving the stability of the slope. Some of these approaches consider the piles as structural elements receiving forces from the upper sliding ground mass and transmitting these forces to the underlying stable one. The force from the top sliding mass is applied at between one third and one half of the pile embedment into the top sliding mass, Anagnostopoulos et al. (1990), Fukuoka (1977) and Matsui et al. (1988). The point of application of the sliding force was explored based on successful case histories while addressing the safety factors for both geotechnical and structural design, Vessely A. et al. (2007). The development of numerical analysis techniques utilizing the method of finite elements (FE) also enabled better analysis and design of slopes stabilized using piles. A FE-based approach was successfully utilized to design slope stabilization with target safety factor based on the shear and bending demands and the spacing of the piles, Pradel D. et al. (2010).After Hurricane Sandy in October 2012, the stability of many properties constructed atop earth slopes located along the coast of the Atlantic Ocean has become a concern due to storm-induced erosion. This paper presents the analysis, design and construction of a hybrid slope stabilization system utilized at one of these storm-impacted properties, which is located in the Atlantic Highlands, New Jersey in the United States. The subject property consisted of a two-story residential dwelling and a parking structure, and was built on top of an about 8-m-high earth slope having crest at about elevation 10 m (el 10) and toe at about el 2."

Jan 1, 1900

By C. Dai, S Raathiv

The Waikato Expressway is one of the New Zealand Transport Agency’s (NZTA) seven roads of National Significance. Coffey is part of the City Edge Alliance engaged by NZTA for the Hamilton Section of the project. The 22km Hamilton Section is the largest and most geotechnically complex section of the Expressway. The Mangaonua gully in Sector 6 is the most challenging geotechnical area of the project for piling works. Together Coffey and Brian Perry Civil have carried out the temporary and permanent design and construction of embankments, piling works, retaining walls and soil improvement works for the bridge construction. The design and construction works were governed by weak alluvial layers and artesian pressure layers several meters beneath the ground level. This paper presents the action taken to improve the foundation of temporary platform, control the artesian pressure, prevent bentonite leakages into the highly permeable alluvial layer and challenges in the base grouting process. This paper summarises the key components in the construction and supervision of bored piling works and outlines innovative solutions for challenges which we faced during the construction.

Nov 1, 2022

By Robert L. Goehring, Fred Munene

This case history for three major additions to a tire manufacturing plant in north Georgia discusses the impact of highly variable Karst (sinkhole) geology on both foundation design and construction. For Phase 3, alternatives were considered for a heavily loaded mixing tower with up to 2,000 kip column loads. A non-traditional approach of using auger cast piles was adopted. To satisfy a risk-averse Owner, a pile load testing program including strain gauges was conducted. One test pile was cored full depth to demonstrate effective bearing on steeply inclined rock. For Phase 4, similar methodology was used at another critical mixing tower structure associated with that phase and the installation procedure was refined to reduce grout take. In Phase 5 construction, another mixing tower and the equipment pits were supported on auger cast piles. After pile installation, a sinkhole opened up between two equipment pits. Remedial grouting was performed. Development also required construction of a R&D building over a 96 inch diameter RCP storm sewer. Auger cast piles were used to support the building to avoid overstressing the existing pipe and risk separating joints. This case history outlines lessons learned while constructing auger cast piles in Karst and proving quality was built into the foundations.

By Arash Khosravifar, Ali N. Ibrahim

"Large areas of Iraq are covered with collapsible soils namely gypsiferous soil which is often used as the foundation soil for structures. In particular, the Mosul Dam foundation is comprised of high contents of gypsiferous soils. Intrusion of water through the foundation soil dissolves gypsum which acts as the binding material between soil particles. This phenomenon results in the formation of collapsible soils which can cause serious damages to the dam structure. The failure of Mosul Dam, with a reservoir as large as 11 billion cubic meter of water, can be catastrophic. In the past, Mosul Dam Authorities have been remediating the soil foundation by injecting cement mortar. This method has been proved not economic; therefore, new, more efficient, methods are desperately needed.This research study focuses on finding practical methods to remediate collapsibility of gypsiferous soils by improving their geotechnical properties. This study presents remediation of collapsible gypsum-rich soil by grouting. Three types of stabilizer materials were used to make the grout; (1) sodium silicate (Na2 O3 Si) which is a well-known chemical soil stabilizer, (2) bentonite slurry, and (3) silicone oil. The purpose for using these stabilizer materials is to provide an impermeable layer (waterproofing coat) around the gypsiferous soil particles and to fill the voids that may occur in the soil as a result of gypsum dissolution when subjected to water.A series of double oedometer (collapse) tests and direct shear tests were carried out on gypsiferous soils before and after remediation by grouting. The results show that the soil compressibility decreases in the grout-treated gypsiferous soil by reducing volumetric strain. Consequently, the potential for collapsibility decreases too. It was also shown that grouting, increases the shear strength of the soil at confining stresses smaller than 250 kPa by increasing the cohesion combined with a slight reduction in the internal friction angle.INTRODUCTIONGrouting is one of the ground improvement techniques which is often used to improve the loose foundation soils. Bruce (2003) provides step-by-step procedures on using grouting techniques for sealing dams and other water reservoirs. Grouting can be classified as permeation grouting, compaction grouting or hydraulic fracturing. Permeation grouting is an effective way to send the grout into the ground without disturbing the soil structure, i.e. free flow of grout into the soil voids where grouting is accomplished by injection of a fluid-like material that is capable of forming a gel and binding the soil particles together. Grout materials may be solution grouts or suspension grouts. The permeation grouting technique is generally used to minimize ground permeability and to control ground water flow, but it can also be used to strengthen and harden the ground (Raman et al., 2012)."

Jan 1, 2017

By Charles Winter

The Ohio Department of Transpor- tation's (ODOT's) $228 million 1-480 Valley View Bridge project was needed to keep traffic flowing on one of the state's busiest freeway segments. Deterioration from age and steady high- traffic volumes necessitated the replacement of the existing decks of the I-480 east- and west-bound bridges over the Cuyahoga River Valley in suburban Cleveland. To facilitate this work without creating tremendous backups and traffic delays due to long-term lane closures, the project included design and construction of a new four-lane bridge in the median gap between the existing 1-480 bridges. Now complete, the new center bridge allows for all four lanes of I-480 to be maintained in each direction while deck replacement and other repairs are made to the existing bridges, while also providing increased capacity after project completion. ODOT awarded the project to the Walsh Design-Build Team (DBT) in late 2017. This article describes how the Walsh DBT, with Jacobs Engineering as the DBT lead design firm, incor- porated an innovative approach to the design and construction of the driven pile foundations for the new I-480 center bridge. I-480 crosses approximately 200 ft (60.9 m) above the Cuyahoga River Valley. With an overall length of 4,150 ft (1,265 m) and spans ranging from 180 to 300 ft (54.8 to 91.4 m), the design and construction of the foundations for the new center bridge were critical to the success of the project. Due to their overall height and span lengths, the foundation loads for a typical pier consisted of a factored vertical load of 22,000 kips, (100 MN) plus significant overturning forces due to horizontal loads and thermal effects.

May 1, 2022

By Fabio Santillan, Lyndon Bedford

"This paper presents the main features of the Wolf Creek Dam Foundation Remediation Project, highlighting the innovative construction approach and stressing on how the collaboration between the contractor and the owner became a key element for the success of this project.The main rehabilitation contract, $341 M, was awarded in 2008 for the construction of a 980,000 sqft concrete barrier. Most of this 2ft-wide concrete barrier wall is being built to depths reaching 277 ft using innovative construction techniques proposed by the contractor and under quality control measures that exceed by far the industry standards.The construction of the barrier wall entails the use of nine different foundation techniques which run concurrently following very stringent requirements in terms of verticality, distance between open elements, strength, permeability and dimensions that control the installation sequence of each barrier wall element.The innovative construction approach by the contractor and the collaborative efforts by the contractor and the USACE (“US Army Corps of Engineers”) have brought this unique and very difficult project to a successful completion, setting new standards in the dam foundation industry and nine months ahead of scheduleINTRODUCTIONWolf Creek Dam is on the Cumberland River in south central Kentucky. It provides hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. The lake is a source of recreation that has attracted more visitors (4.89 million) than Yellowstone National Park (2.87 million).The dam and its adjacent reservoir reside upon a heavily Karst bedrock foundation. In late January 2007, the USACE placed the dam under a 'high risk' for failure designation. As a temporary measure, the pool elevation was lowered to 680 ft Above Main Sea Level (“AMSL”), 80 ft below its maximum capacity, with huge impacts to the local economy while the major, and ambitious, $ 594 million remediation program to bring the dam back to its full operating condition was carried out.The main rehabilitation contract of $341 million was awarded in 2008 for the construction of a 980,000 sqft concrete cut-off barrier. Most of this 2ft-wide concrete barrier wall has been built to depths reaching 277 ft using innovative construction techniques under quality control measures that far exceed the industry standards."

Jan 1, 2015