Search Documents

By Marco D. Boscardin, Benjamin H. MacKinney, Kenneth R. Allard, Kenneth A. Pidgeon, Adriane G. Boscardin

This paper presents a case history for a unique application of a system of vertical micropiles with horizontal soil nail bracing and shotcrete facing for underpinning. The system was used to support and protect an existing 2-story hospital building during demolition and renovation. The goal was to limit building movements and have the building remain in use during construction of an abutting addition. Soils at the site consisted of clean, loose to dense, sand and gravel. The original underpinning design was revised after the initial excavation revealed unsuitable soil conditions for traditional underpinning pits. An alternative system consisting of vertical micropiles (hollow bars) through the footing, combined with shotcrete and soil nails was proposed, accepted by the owner, and successfully constructed. Excavation depths were up to 15 feet (4.6 m) below the existing footings. Wall movements were monitored at regular, horizontal and vertical intervals along the hospital wall, and less than 0.6 inches (15 mm) of settlement and 0.1 inches (3 mm) of horizontal displacement throughout underpinning and construction were reported. The challenges with the original proposed support of excavation design and other alternative approaches considered will also be discussed.

Oct 1, 2022

By Juan M. Pestana, Jeremy M. Gasser, Cuneyt Gokmen, Paul J. Sabatini, William Tanner, Daniel J. Woeste

An access pathway and working platform were designed and constructed for equipment access for a Deep Soil Mixing (DSM) pilot study over a coal combustion residual (CCR) surface impoundment (SI). The DSM pilot study was conducted to evaluate slurry mix designs and construction techniques for installing DSM columns up to 95 feet deep. Two-dimensional (2-D) limit equilibrium and 2-D finite element analyses were used to evaluate multiple failure mechanisms including: (i) bearing capacity, (ii) punching shear of mixed ground and underlying CCR, (iii) effect of fluidized DSM columns on working platform stability, and (iv) liquefaction. The analysis results were used to design ground improvement required to increase bearing capacity and stability of the CCR under the proposed equipment access route. A long-reach excavator was used to perform shallow bucket mixing and walk onto the CCR SI atop previously mixed cells following a minimum cure time and acceptance of quality control test results. Prior to mobilizing the DSM rig, a static load test was conducted to evaluate performance of the working platform. Both the access pathway and working platform demonstrated acceptable performance under the design loads during the DSM pilot study. This case study emphasizes the economic and safety benefits that can be realized by appropriately designing critical temporary work items such as access pathways and working platforms in difficult ground conditions. INTRODUCTION A Deep Soil Mixing (DSM) pilot study was conducted at a coal combustion residual (CCR) surface impoundment (SI) to evaluate slurry mix designs and construction techniques for closure design of the SI (Site). Sluicing of CCR at the facility ceased and closure will be initiated based on requirements in the final United States Environmental Protection Agency (USEPA) Rule for Disposal of Coal Combustion Residuals from Electric Utilities, 40 CFR 257, effective October 19, 2015. The proposed closure approach involves constructing a DSM containment structure (DSM Wall) to separate the SI into two areas: (i) a closure by removal area; and (ii) a consolidate and cap-in-place area. The proposed DSM Wall would retain the CCR within the consolidated closure footprint and provide a barrier between the two areas of the SI. The predominant CCR in the SI where the pilot study was conducted were fly ash and bottom ash. CCR materials in surface impoundments are generally soft and saturated as a result of being sluiced into place and can present stability and safety challenges when performing earthwork activities.

Jan 1, 2019

By Thomas G. Tavernaro, Jeffrey A. Schaefer

"The $106 million Olmsted Approach Walls Project, completed in the spring of 2004 by Massman Construction Co., Kansas City, MO, is one phase of a new $1.4 billion Corps of Engineers locks and dam facility located at Mile 964 on the Ohio River, approximately 17 miles (27.4 km) upstream of its mouth at the Mississippi River. When completed, the Olmsted Locks and Dam (Figure 1) facility will replace two aging locks and dams (Locks and Dams 52 & 53) built in the 1920’s, and produce an estimated $600 million annual economic benefit to the nation through reduced lockage time and operation and maintenance costs. PROJECT OVERVIEWThe Olmsted Approach Walls Project consisted of “in-the- wet” construction of four fixed nose pier structures, four floating concrete approach walls, one fixed wall and related underwater excavation, grading and stone placement. Over 12,000 tons (11,000 tonnes) of structural steel and pre-cast concrete elements, up to 335 tons (304 tonnes) in weight, were safely erected during the project.To support these massive structures, the Louisville District of the U.S. Army Corps of Engineers teamed with INCA Engineers, Inc., Bellevue, WA to design thirty seven 10’ (3m) diameter shafts (cast-in-place steel-shell piles) capable of maintaining elastic behavior below ground while resisting barge impact loads, extreme head-on collisions from runaway tows, and environmental forces from river current, wind, and seismic events.The shafts (typically 150’ (45.7m) in length) were founded 100’ (30m) into the riverbed through alluvium, a very consolidated fine sand and clay Cretaceous soil, and finally into a hydrothermally altered rock. Thirty seven shafts were installed under open river conditions at the site, a group of four shafts at each nose pier-pylon location (Figure 2), and 21 at the fixed land wall. Due to difficulty in achieving the required casing tip elevation the team developed a design modification that was successfully implemented for 27 of the shafts.Concurrent with the work at Olmsted, eleven pontoon segments for the four floating approach walls were constructed at a graving yard in Paducah, KY, developed by Massman Construction Company specifically for the project. While the pontoon geometry varied, the pontoons averaged 350’ (107m) in length, 40’ (12.2m) in width and weighed 4,500 tons (4,082 tonnes). The longest of the four walls, at 1,700’ (518m) was comprised of five interconnected pontoons."

Jan 1, 2006

By C. Y. Liu

This paper principally deals with the application of caisson foundation in the Chinese bridge building industry, the different types of caisson foundation adopted, and their spheres of application. Caisson foundation has been used and speedily developed for bridge works in New China, and a number of new innovations have been made in its design. Especially in deep water foundation, the Nanjing Bridge over Changjiang has attained one of the deepest bridge foundations in the world. There are six types of deep caisson foundation being now in use in China, namely:

Jan 1, 2010

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

By Luo Yang

It has been known that after initial pile driving, pile capacity gain over time (set-up) could constitute a significant portion of the total pile capacity. In the past, there has been very little guidance for incorporating pile set-up capacity in design. This may be due to large uncertainties involved in predicting the pile set-up. A comprehensive statistical database is developed to describe the increase of pile axial capacity with time, known as set-up, when piles are driven into sand. Based on the collected pile testing data, pile set-up is significant and continues to develop for a long time after pile installation. The statistical database shows that a lognormal distribution can be used to describe the probabilistic characteristics of the predicted set-up capacity using Skov and Denver?s equation. The main objective of this paper is to incorporate the set-up effect into a reliability-based Load and Resistance Factor Design (LRFD) of driven piles in sand. A First Order Reliability Method (FORM) is used to derive separate resistance factors that would account for different degrees of uncertainties associated with the measured short-term capacity and the predicted set-up capacity from the proposed semi-empirical equations. The incorporation of set-up effects in the LRFD helps improve the prediction of the total capacity of driven piles, resulting in more economical design. A practical design procedure within LRFD framework to incorporate the pile set-up effect is outlined at the end of the paper.

Jan 1, 2006

By Patrick van der Schaaf

"During 2016, foundation piling works were completed to allow for the construction of a production and storage/handling terminal in Rotterdam. It is there that steel foundations will be produced for offshore wind farms and the oil and gas industry. Several Dutch contracting companies were involved in constructing: foundations for an assembly hall, a barge quay and a deep-sea quay wall. For the hall foundations, cast in situ concrete vibro piles were created. Open ended steel casing piles were also installed due to very high cone resistances which made it impossible to perform cast in situ piles in certain areas. The quay wall was constructed with open ended steel casing piles in combination with sheet piles. A deep-sea quay wall was also constructed to provide enough storage area for the offshore mono piles. This project was unique and challenging due to the use of different foundation technologies in challenging circumstances and soil conditions. This paper will give an insight into the Dutch use of varying foundation piling techniques for deep-sea quay wall constructions. It can be concluded that even experienced local contractors can be surprised by variations in soil conditions. It will also show how the contractors adapted to the difficult circumstances.PROJECT OUTLINEThe project consisted of a barge quay near the assembly hall with a length of 500 metres, width of 42 metres and a height of 35 metres, and a deep-sea quay wall 480 metres in length. This paper concentrates on the foundation works for the construction of the deep-sea quay wall. The construction of the deep-sea quay wall consisted of a combination of open ended steel casing piles with a diameter of Ø 1420 mm and a wall thickness varying between 21 and 23 mm. The lengths of the steel casing piles varied between 32 and 37 metres. Between the steel casing piles triple PU 28 sheet piles were installed with lengths varying between 26 and 29 metres. In the Netherlands, a combination of open ended steel piles and sheet piles is known as a “combi wall”. For the deep-sea quay wall a steel combi wall was shored with steel H- section profiles that were driven in a raked position whilst being injected with grout, so called MV-piles. The MV piles for this project consisted of steel HEB 600 sections with lengths from 52 up to 59 metres and were installed with angles varying between 42.5 and 47.5 degrees. For a detailed overview regarding the project specifications reference is made to table 1 which is presented below."

Jan 1, 1900

By Peter Middendorp

Pile foundations are widely applied in the Netherlands because of the soft soil conditions. One of the popular pile types are cast-in-situ piles, which have to be integrity tested to get accepted. Integrity testing has been applied for more than 30 years, with the number of integrity test performed nowadays exceeding 400,000 per year and subsequently there is a substantial amount of practical experience with this testing method. This paper will deal with some basics of integrity testing and describe some of the techniques that have been adopted in the Dutch pile testing practice, like detection of pile head defects with a spike type hammer pulse, and the site average or pile group average for the qualitative interpretation of measured signals.

Jan 1, 2006

By K. Madhusudan Reddy

Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load?deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.

By Mohsen Elsayed, Amr Sallam, Ahmad Mohamed, Xuebing Zheng, Mohamed Alrowaimi

The foundation is an essential component of the wind turbine that ensures continued operation under stable and safe conditions. Both shallow and deep foundations are utilized to support wind turbines including gravity spread foundation, anchor foundation, pier or drilled shaft foundation and pile and pile cap foundations. Conventional methods were typically utilized to design the wind turbine foundations. With the advances in numerical modeling in the geotechnical field, foundation designers may utilize numerical analysis to design wind turbine foundations. Geotechnical numerical packages allow modeling structural components and soil-structure interaction that is usually neglected in conventional methods. Furthermore, the subsoil conditions, geometries, stress-strain behavior, boundary conditions and load staging can be modeled, minimizing the assumptions and generalization. This results in better understanding of the stress strain behavior of the foundation leading to optimized foundation designs. This paper includes a brief review of current foundations used to support wind turbines with an emphasis on post tensioned single pier foundations. The current conventional foundation design methodologies and state-of-the-art foundation design utilizing numerical modeling of the single pier foundation will be discussed. Two case histories where the single pier foundation, designed using numerical modeling, were utilized to support the wind turbines will be presented. INTRODUCTION The foundation is an essential component of every wind turbine that ensures continued operation under stable and safe conditions. Turbine manufacturers provides load specifications for designers to be utilized for wind turbine foundations design. Loads include bending moments, torsional moments, lateral forces and vertical forces in both operational and extreme wind conditions. Essential specifications under seismic conditions might also be provided in seismic prone areas. Turbine manufacturers also include foundation design criteria including minimum rotational stiffness, minimum horizontal stiffness, maximum allowed inclination and maximum allowed lateral movement under both operational and extreme loads. Geotechnical explorations and evaluations are typically performed at early stages of the wind development projects. The field explorations usually include Standard Penetration Test (SPT) borings, Cone Penetration Test (CPT) Soundings, geophysical surveys, and laboratory tests to define soils stratification system and soil strength and compressibility characteristics. The most critical soil parameters for turbine foundation design are shear strength parameters (cohesion and friction), shear modulus, Poisson’s ratio, and unit weight. The depth to the groundwater table is also a crucial parameter in design. Advanced field explorations techniques such as Dilatometer Tests and Pressuremeter Tests may also be utilized. Laboratory tests for foundation design typically include index parameters, consolidation and triaxial tests.

Jan 1, 2019

By William B. Conway

This paper will describe the large caisson pier foundations for four of the bridges crossing the Mississippi River in the New Orleans area; and will discuss some of the unusual problems encountered during their sinking. Certain settlement phenomena experienced during their service life will also be related: The four bridges in order of their construction: The Huey P. Long Bridge, River Mile 106.1, completed in 1935 The Greater New Orleans Bridge No. 1, River Mile 96.0, completed in 1958 The Hale Boggs Bridge, River Mile 121.6, completed in 1983 The Greater New Orleans Bridge No. 2, River Mile 96.1, completed in 1988 Each of these bridges employed large open-dredged concrete caissons as foundations for one or more of the river piers, with the smallest being the 65ft by 102ft caissons for Piers I and II of the Huey P. Long Bridge and the largest being the 99ft by 214ft caisson for Pier II of the Greater New Orleans Bridge No. 2. The Huey P. Long caissons are founded in a dense fine sand at -170 while all of the other bridge caissons are founded in hard preconsolidated clay at elevations varying from -150 to -185. The Huey P. Long Bridge is currently being widened without increasing the caisson foundations under any of the river piers; and the design reasoning that led to this decision is presented.

Jan 1, 2013

By Ramdane Bahar

The new Algiers airport building is a reinforced concrete building of more than 80 thousand square meters of floor slabs. It is located at Dar-EI-Beida, near the old passenger terminal, about 20 km east of Algiers. The project is designed to receive about six millions passengers annually and leaves the possibility of future extension. Due to the presence of a top layer of compressible soil and great concentrated loads transmitted to the foundations, the building is to be founded on 1730 bored piles of 1.2 meter diameter varying in length between 14 and 28 m. Construction work started in 1986 and was interrupted in 1996 due to financial difficulties when the structure was almost complete. The structure was left unattended for more than three years without any weatherproofing and in 1999 a new firm was appointed to complete the work and hence an evaluation of the existing structure was necessary. This paper describes and discusses the foundation design, construction supervision, site quality control and assessment by the parallel seismic method of the deep foundations built in cohesive soils. The variation in soil conditions and identified geotechnical and hydrogeological problems associated with the development of the area, required a thorough knowledge of the soil conditions. A variety of tests, involving more than 200 locations, were carried out. The ground investigation, pile tests as well as different problems encountered during piles construction, are presented.

Jan 1, 2002

By M. B. Wechsler

An analysis is developed for determining the maximum loading, as well as the potential uplift of the piles on bridge pier foundations. There are considered piers supported on two through seven rows of piles, and related to two simply supported collinear superstructures of any structural material. The study leads to different types of influence lines for various load combinations. For load combinations containing vertical loads only, the related influence lines are similar to those as for the bending moments of a virtual span covering the two actual spans, as well as the gap between the two superstructures; and, in this case, the heavier loads should be positioned in the vicinity of the pier. While, in the case when vertical loads are acting together with hori­zontal forces, the related influence lines will indicate where the heavier live loads should be positioned. And they will also indicate on which portions of the spans the live load should be avoided.

Jan 1, 1989

By Ke Yang

Drilled shafts are widely used as foundation system for sound walls to resist lateral loads. The design method based on the ultimate lateral capacity, such as Broms method, is often used for sound wall foundation design. Allowable Stress Design (ASD) is currently used for deep foundation design. However, by October 2007, all states Department of Transportations are required to use the Load Resistance Factor Design (LRFD) approach for the design of foundation in highway projects. There is a need to develop a calibrated resistance factor in LRFD lateral design of drilled shafts supporting sound barrier walls. This paper provides resistance factors for design of laterally loaded drilled shafts supporting sound walls using Broms method based on the study using reliability based method and fitting to ASD method. Additionally, the resistance factors for static lateral load tests are recommended. Furthermore, a methodology to update the resistance factors using Bayesian approach by incorporating the on-site full-scale lateral load test results is presented. To illustrate the Bayesian update methodology, two lateral load tests in Colorado were employed to develop the updated resistance factors.

Jan 1, 2007

By George Piscsalko

"Quality control of drilled shafts and CFA piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult or not possible to fully inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. CFA piles are cast with no ability to inspect the shaft prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and CFA piles. This paper will compare evaluations by three existing non-destructive test (NDT) methods with a new method of Thermal Integrity Profiling for assessing integrity in drilled shafts and CFA piles. This Thermal Integrity Profiling method determines the integrity over 100% of the shaft cross section, both inside and outside the reinforcing cage, by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements are made typically only 12 to 48 hours after concrete placement, thus accelerating the construction process. Thermal Integrity Profiling will be described in detail and the Thermal Integrity Profile (TIP) results from several shafts with purpose built defects will be discussed along with several case histories from drilled shafts and CFA piles where Thermal Integrity Profiling was used. The case histories will compare TIP with various other NDT tests utilized on these particular piles including comparisons with Low Strain Integrity Testing and Cross Hole Sonic Logging. Test results for the various methods will be discussed and the excavation of the upper portion of one drilled shaft will be shown and discussed. IntroductionDrilled shafts can be a desirable foundation element in many applications due to the large axial and lateral capacities which are attainable for very large drilled shafts. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. CFA piles are another popular choice for their relative ease and speed of installation. The trend has been larger CFA piles carrying greater loads, which makes quality control critical for these piles. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2014

By Unnikrishnan Nair, Sandeep S. Nikam, Sanjay D. Patil, Prabir C. Basu

"Mumbai Metropolitan Region Development Authority (MMRDA) entrusted to implement Monorail Systems in various parts of Mumbai Metropolitan Region (MMR) with the objective to supplement the present transport system in MMR. The stretch of Monorail is starting from Sant Gadge Maharaj Chowk (SGMC) and extending up to Chembur Railway Station, divided into 2 phases. Construction of Phase 1 (Chembur to Wadala Depot) is complete and Phase 2 (Wadala Depot to SGMC) is under construction.Monorail runs on prestressed girder (guide beam) of span ranging from 20m to 28m supported on pier founded upon group of end bearing piles embedded in rock, pile group ranging from 2-4 piles of diameter 1000mm each.For the purpose of site characterization, geo-technical investigations were carried out along the alignment of Monorail system as mentioned above. These investigations included field and laboratory tests. The subsurface strata mainly consist of silty sand, gravel, underlain by marine clay extending up to stronger basalt rock with volcanic breccia. Overburden consisting of mainly marine clay ranging from 5.5m to 11m at all locations within the influence zone of settlement.The existing rigid pavement along of Sion-Koliwada and Anik-Wadala were constructed about 5 years prior to the construction of Monorail piers. Before laying the rigid pavement, to improve the geotechnical strength of subsoil (mainly marine clay), ground improvement using stone columns was undertaken by MMRDA. In light of limited right of way, the Monorail piers have been constructed in the median portion of the road. The line became operational on February 2014, in few months it was noticed that, in the vicinity of the Monorail piers, along Sion-Koliwada link and Anik-Wadala link, the Road Pavement Quality Concrete (PQC) panels adjacent to the Monorail piers started showing distress in form of nonuniform settlement of the concrete panels.Effect of pile foundation on pavements/PQC slab distress and possible causes of distress were investigated. Initially the distress was thought to be upheaval of monorail pier cap, but further investigations revealed the same to be soil settlement occurring over time. This paper describes the investigation carried out for identifying the cause of this settlement."

Jan 1, 2015

By Venugopal B, M Kumaran, Thomas John, Vetriselvan A

The initial pile load tests are conducted to ensure the geotechnical capacity of the pile in a particular site condition. Normally kentledge method is adopted for the compression pile load tests. In this method the entire kentledge load is loaded above secondary beams which are supported by concrete blocks above the Natural Ground Level. So, it is important to ensure the SBC (for shear and settlement) of the natural ground. In one of our projects initially it was decided to go with kentledge system for initial compression load test on 56m long 1200mm diameter BCIS pile. The test load and total kentledge load were 2160t and 2700t, respectively. The soil strata mainly consisted of clay with low SPT N value and water table almost at ground level. It was suggested to replace top soil using Granular Sub-base (GSB) with good compaction in order to avoid excessive settlement of concrete blocks placed to support the kentledge weight. When the kentledge loading started, even before reaching 10% of total kentledge load, excessive settlement on the GSB layer was observed. This paper describes the problems faced during normal kentledge method and how it was overcome using the liner pile system for initial compression load tests in this particular site condition for higher test load.

Nov 1, 2022

By A. Ortigão, M. Felix, E. Falk, T. Koehler

"Ground improvement techniques such as vibro-replacement or deep soil mixing are fairly young products in the Brazilian geotechnical market. Soft soils in this country are deep, very soft, have low sensitivity and are challenging. In general, ground improvement techniques are increasingly selected as more costefficient and flexible solutions on infrastructure projects compared to the conventionall technologies such as piled embankments, wickdrains with surcharge or jet-grouting. The geotechnical challenge expansion project for the Porto Alegre Airport, South Brazil, involved a taxiway area of five ha of 8 to 10 m of soft clay deposit. The deep soil mixing (DSM) technique was selected as a cost-effective solution to reduce settlements. As part of the design, an extensive soil investigation programme includ ing laboratory and field trials was carried out to define the most economical slurry-recipe, DSM installation patterns and quality control specs. This paper gives details of the field and laboratory trials and present results.INTRODUCTIONThe International Airport of Porto Alegre in the state of Rio Grande do Sul in Brazil is located in an area with extensive sediments near to Guaíba Bay. During the different construction phases of the airport over the last decades, the soft clay deposits have been a challenge for the local geotechnical community as well as for the specialized contractors (Schnaid et al, 2001). As part of the most recent expansion scheme, a cargo-terminal with a five ha airplane tarmac area will be constructed."

Jan 1, 2015

By Sanjay Gupta, Sorabh Gupta, Ravi Sundaram, Abraham Varghese

"Geotechnical investigation for the Kochi Metro revealed a critical section of the Viaduct near Ernakulam Junction Railway Station. Four piers, located over a 220 m stretch, were passing through an area with substantial thickness of soft clay. The scope of the geotechnical investigation included two boreholes and a static cone penetration test at each pier location. In the boreholes, field vane shear test was conducted at different depths in addition to the routine SPT. The design of heavily loaded piles in such strata is a challenge due to the liquefaction of the shallow sands and negative skin friction / down-drag in the soft under-consolidated clay. Bored cast-in-situ piles of 1500 mm diameter extending to 50-60 m depth were used to carry 500-600 tonnes load.INTRODUCTIONThe first phase of the rapid transit system at Kochi, Kerala (See Fig. 1) whose elevated route spans from Aluva to Thripunithura covers a total distance of about 25 kilometers. One of the more critical sections of the viaduct exists near the Ernakulam Junction Railway station where the alignment takes a sharp curve to move towards Vyttila, crossing the railway tracks and running partially over the approach of South over-bridge.In this section, four piers located on either side of the railway tracks near the Route Relay Cabin of Ernakulam Junction Railway Station pass through an area with substantial thickness of soft underconsolidated clay.The alignment is geotechincally challenging due to the presence of loose liquefiable sand and soft underconsolidated and sensitive clay.Initial investigations by the owner based on limited boreholes only yielded conservative and inconclusive pile capacities. For a thorough understanding of the soil behaviour, a detailed geotechnical investigation was carried out to assess the engineering behaviour of the soil strata.The scope of the geotechnical investigation included two boreholes and a static cone penetration test at each pier location. In the boreholes, field vane shear tests were conducted at different depths in addition to the routine SPT."

Jan 1, 2015

By Jie-qun Zhai, Jian Jia, Ke Yang, Xiao-lin Xie, Yu Zhang

"With cities’ development, underground space exploitation presents a need for bigger and deeper constructions now. Technical problems founded during the construction of deep foundation pit support become more and more important. The supporting system has to cut or partly cut off hydraulic connection outside and inside the foundation pit, control the ground settlement caused by dewatering and make sure safety of foundation pit and its surroundings. Some preliminary study and application of ultra-deep soil reinforcement methods have been conducted in Shanghai’s deep excavation engineering. On the basis of engineering practice of ultra-deep foundation pit in Shanghai, some field and laboratory test, this paper analyzes effects of different ultra-deep soil reinforcement methods and their influence characteristics of surrounding environment. It also summarizes these methods’ sealing effect, construction and economic efficiency and concludes their characteristicsINSTRUCTIONShanghai is formed from marine sedimentation. In Shanghai, from earth’s surface to 30~40m underground, soil is mainly consist of soft clay with 40% moisture content. There are also many thin silty-sand layers in the earth, so the soil is both soft and permeable. Under 40m, soil is mainly thick silty-sand layers and fine-sand layers with medium density and confined groundwater whose water head is about 7m high.With the rapid development of Shanghai’s municipal construction and high-rise buildings in the recently ten years, the number of underground structure including subway station, tunnel and high-rise building basement are constructed rapidly. Due to the permeability and softness of Shanghai’s soil, it is necessary to reinforce soil to make sure the safety and high construction rate of engineering project in Shanghai.Because of deeper excavation depth and bigger excavation area in Shanghai, ultra-deep soil reinforcement is used preliminarily in Shanghai. Combining with engineering practice of ultra-deep foundation pit in Shanghai and employing field and laboratory test, this paper analyzes effectiveness of different ultra-deep soil reinforcement methods and concludes these methods’ characteristics and their applicability. All this can guide further application of these methods."

Jan 1, 2015