Search Documents

By D. Steele, B. Ndlovu

"Adequate characterisation of clays is becoming increasingly important as operating mines move into areas of more complex ores. The processing therefore needs better mineralogical characterisation to identify problematic ores for better planning before issues arise. While a number of instrumental mineral characterisation methods are available, X-ray Diffraction (XRD) is widely recognised as perhaps the best technique for the identification and quantification of minerals, particularly clays. When an appropriate sequential and systematic sample preparation and treatment protocol is employed with instrumental XRD analysis individual clays can be uniquely identified, and the proportions of interstratified clays can also be quantified. The effect of sample preparation on the XRD analysis and identification of clays was investigated in this study. The results showed that sample preparation protocol is indeed critical to accurately analysis and characterisation of clays. For example, both dry grinding and micronizing affected the degree of crystallinity of kaolinite leading to the formation of reactive surfaces or changes in the physicochemical behavior. It was also found that the apparent degree of preferred orientation in platy minerals correlates directly with the amount of force/pressure applied during the preparation of backfilled powder samples. This work showed that manual preparation can produce highly variable peak intensities especially with minerals that show any preferred orientation. KEYWORDS Clay; XRD; kaolinite INTRODUCTION Clays are important in our life and they have numerous applications in modern world from cosmetics to environmental remediation. Therefore, clays have been extensively investigated for many years. Adequate characterisation of clays is becoming increasingly important as the mineral processing industry faces more complex mineralogy with the need for better mineralogical characterisation to identify problematic ores and plan accordingly. In most studies, X-ray diffraction (XRD) method has shown the unique capability to characterise mineralogy, especially for the fine grained size materials. The XRD technique is particularly diagnostic for clays. It is known that under ideal conditions, the peak intensities of an XRD diffractogram are proportional to the concentrations of individual minerals present in the sample. Hence, the qualitative mineralogical data obtained from XRD can be quantified, using either the internal or external standard methods. However, it is also known that clays are particularly sensitive to the influences of sample preparation method due to their physical characteristics (e.g. fine grain size, morphology, relative physical softness, crystallinity, thermal sensitivity) that could be destroyed by inappropriate preparation prior to the analysis. Thermal and mechanical treatment and grinding of clays can change their crystalline structure, and consequently, their characterisation results by XRD analysis. The behaviour of clays in grinding has been widely studied, especially for kaolinite (Miller and Oulton, 1970, Milocevic et al., 1992, Tomasevic-Canovic et al., 1992). With prolonged grinding time, the crystallinity of the clays can decrease (Filipovic-Petrovic et al., 2002). It has been shown that grinding may gradually cause the loss of hydroxyl ions of kaolinite (Gonzalez Garcia et al., 1991)."

Jan 1, 2018

By N. Panteleeva, E. Konoplev, I. Michailova, S. Titkov, S. Aliferova, T. Gurkova, T. Chumakova

Cationic flotation using alkylamines and their derivatives as collectors, and characterized by high selectivity of mineral particle separation, is finding ever growing industrial application. In recent years the industrial application has been initiated of new cationic collectors - alkylmorpholines. Efficiency of cationic surfactants operation as collectors is dependent upon their colloid and sorption properties and the availability of silicate .carbonate rock-forming mineral impurities in the ore, which sorb the cationic collector. Investigations have been carried out on the influence of frothers and organic depressors with various compositions upon physical-chemical and flotation properties of alkylamines and alkylmorpholines. On the basis of these investigations requirements for organic depressor were developed and new flotation reagents were proposed (V-1 frother and KS-MF depressor). The use of new reagents enables one to decrease considerably the consumption of expensive cationic collectors and to enhance the floatability of coarse mineral particles. Data of new reagents industrial application is presented. The reagents developed can be used for flotation processing of other ores.

Jan 1, 2003

By M. Morales, J. Yianatos

"In this work, an alternative approach to evaluate the flotation performance along a flotation rougher row is presented. The collection zone as well as the froth zone performances were separately evaluated. For this purpose, sampling for metallurgical balances along with sampling of top-of-froth (TOF) grades in each cell of a flotation row were employed. The modelling of the rougher circuit consisted of using TOF grades for evaluating the collection zone recovery, because they are a good representation of the bubble loading, which identifies the true flotation process, as shown in previous studies for shallow froths. In addition, the feed characterization, size-by-liberation, allowed the identification of the mineral distribution and its evolution along the circuit. The latter result was obtained by fitting the recovery profiles as well as the TOF grades down the flotation bank. The flotation rates and the maximum recoveries in terms of size-by-liberation (size classes: -45 µm, +45-150 µm, +150 µm, and liberation classes: -20%, +20%-80%, +80%) were then estimated. The results were in good agreement with those reported in literature by other authors and showed the new approach allows flotation kinetics to be characterized in industrial circuits.INTRODUCTIONMineral recovery in industrial flotation circuits is a function of the mineral characteristics, such as particle size distribution and liberation (Trahar, 1981, Jameson, 2012), and operating conditions such as air flowrate, pulp flowrate, solids percent and reagent conditioning (Jameson 1977; Klimpel, 1980; Mehrotra and Kapur, 1974). The cell type and size (self-aerated or forced air) and the circuit arrangement (single cells or banks of cells in series) are also relevant factors. Sampling of circuits (e.g. rougher, cleaner or scavenger) are commonly carried out using standard automatic samplers for metallurgical balance assessment. However, the flotation plants are generally not provided with proper accesses for local streams, which hinders the recovery estimations and the flotation rate characterization."

Jan 1, 2018

By D. Saramak

The comminution technology based on High-Pressure Grinding Rolls presses (HPGR) application is currently one of the most efficient methods of hard ore comminution from the scope of the energy consumption and the development of industrial HPGR applications in ore preparation circuits is presently the world trend. However, even though the technology is already in use in many countries, which are the leaders in application of modern mining technology, there is still lack of base investigations over the HPGR performance. Throughput and energetic models of HPGR performance are quite well developed, but technological models predicting the comminution effects still needs an in-depth research. In the paper authors present the method of modeling of HPGR products? particle size distribution with using of suitable mathematical models. A basis of the HPGR performance assessment and HPGR-based crushing circuits design is a product?s particle size distribution. In order to precisely determine the particle size distribution of a HPGR product, parameters of product?s particle size distributions should be conditional on the main technical parameters of the roller press like operating pressure and the speed of rolls. The most accurate approximation of a distribution of size particle d appeared the Weibull?s truncated distribution and it is possible to obtain significant relationships between the approximation formula and the value of operating pressure, or feed characteristics. It makes possible a determination of mass recoveries of the product?s respective size fractions and the productivity planning. Instead of pressure (P), the other HPGR operating parameters can be applied, but the P value appears to produce the most relevant relationship. Keywords: HPGR, comminution, particle size distribution, ore processing

Sep 1, 2012

By Charlene Gokhale

Geopolymerisation has emerged during the last few years as an industrial and ecological approach to construction and waste management. By utilizing waste materials and their reactive properties, it is now possible to create geopolymers systems that not only mechanically durable enough to be used as construction materials but are also potential stable immobilisation systems for toxic waste. Previous studies by Van Jaarsveld et al. (1997) and Van Jaarsveld et al. (1998) have reported on the numerous applications of geopolymers in the immobilisation of toxic metals. Research into the possible utilisation of geopolymers as an encapsulation media for organic waste has however been rare. This paper therefore provides an insight into the possible utilisation of geopolymers as a binder for hazardous organic materials.

Jan 1, 2003

By M. E. Holuszko

This paper reports the results of induction time measurements carried out on the products of film flotation of galena and sphalerite particles from three different size fractions (38~75µm; 75~150µm; 150~212µm). As expected, the tailings (sinking fraction) from film flotation at any particular surface tension, had always longer induction times than the concentrates (floating fraction), for both minerals. The difference between the induction times of film flotation concentrate and tailings could be as little as 2.5 ms and 5 ms, and as large as 6 ms and 10 ms. These differences can be related to the different hydrophobic characteristics of these fractions, as expressed by (?c) and composition of the particular film flotation product. In addition, the induction times of the larger particle size fraction were shown to be longer than for the corresponding smaller particle size fraction, even though the average ?c(degree of hydro-phobicity) of these fractions appears to be very similar. Desliming, Cu activation and collector addition to the sphalerite samples was shown to decrease the induction time values significantly.

Jan 1, 2014

"The thiosulfate leaching process developed by Barrick to treat sulfidic high preg-robbing gold ores uses calcium thiosulfate as the leaching reagent for ores pre-treated by pressure oxidation, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a means of reagent recovery. A large portion of the research that led to the development of the technology was based on previous studies completed by different groups over the years, mainly focused on the ammonium thiosulfate system. Operational limitations in the use of the ammonia-containing recycled water in the pressure oxidation circuit were some of the main drivers for the change from ammonium to calcium thiosulfate for the development of the industrial scale process. One of the main aspects for successful gold extraction and recovery in the thiosulfate system is the pseudo-equilibrium reactions that drive distribution of the different gold species (in solids, solution and on resin) in the system. Previous studies have been focused on the thiosulfate reactions and equilibrium constants for the oxysulfur ions (thiosulfate, trithionate, tetrathionate). However, the literature around the effects of the different metal-oxysulfur complexes (Cu and Hg complexes) that form when the ore is in contact with the leaching reagents, and the related effects on stability of the gold complex is limited. The main changes in the gold complex chemistry and stability in the calcium thiosulfate system as compared to the ammonium and sodium equivalents, as well as related effects on gold recoveries, were investigated in the presence of different types of double refractory ores. INTRODUCTION Barrick has developed a thiosulfate leaching process to treat double refractory gold ores, by combining the use of acidic and alkaline autoclave pre-treatment with thiosulfate resin-in-leach (RIL). The process currently in operation at the Goldstrike mine (the TCM process), uses calcium thiosulfate as the leaching reagent, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a mean of reagent recycle. The main feed to the process plant is highly preg-robbing sulfidic ore from Goldstrike’s open pit. Prior to feeding the pressure oxidation circuit, the ore is processed through the crushing and grinding circuits and treated in preparation for acid or alkaline autoclave processing (POX)."

Jan 1, 2018

By E. G. Ozhogina, O. B. Kotova

"The ores of black, non-ferrous, rare, noble metals are mostly distinguished by a variety of mineral types and complexity of their material composition.The article is devoted to the promotion of the concept of mineral processing in modern realitiesof the deficit of high-quality ores and increase their demand.Normative and methodical documentationsfor specific types of analysis with the definition of the field of application are shown. For example,the pyrochlore-monazite-goethite ores from one of the deposits from Eastern Siberia - Chuktukonskoe ore fieldare tested. The development of mineralogical methods, and testing of specific raw materials are shown.The method of small-angle X-ray (and also synchrotron) scattering, which was developed for solving problems associated with structural high-resolution diagnostics, was tested for bauxites of Vezhay-Vorykvinskoye field. KEYWORDS Technological mineralogy, rebellious ores, ore quality assessment, ?mineralogical-analytical methods INTRODUCTION A highly intense production of many types of mineral raw results in gradual depletion and deterioration of mining-geological and mining-technical conditions of development. Relatively easily accessible and rich deposits are getting exhausted in the first place, and it is necessary to involve poor and rebellious ores into production and processing. Traditional technologies can hardly be applied (Chanturia, 2017; Bazin et al., 2014; Ponaryadov, 2017). The urgency of development of the concept of technological mineralogy focuses on the confirmation of new methods and approaches to the development of mineral raw, creation of scientific and methodological prerequisites for solving the problem of rational development of mineral raw, maximal extraction and integrated application of all minerals (both principal and associated), expansion and strengthening of mineral and raw base. The article is aimed at updating tasks that should be addressed within the applied mineralogical researches: – the forecast of quality of ore at early stages of exploration and technological indicators for the redistribution of raw, – interactive monitoring of these indicators by mineralogical and analytical methods; – assessment of environmental consequences of mining and processing of minerals and measures that eliminate these consequences."

Jan 1, 2018

By Francisco Cubillos, Jorge Menacho, Cesar Gomez, Juan Rodríguez

Mineral flotation is the most used process to selectively separate particles of one or more minerals of interest. The process uses natural or induced hydrophobicity to collect particles on the surface of rising bubbles through collisions and formation of bubble-particle aggregates. Flotation machines must keep particles in suspension and well distributed, while at the same time, disperse a mass of air into a population of small bubbles. The efficiency of the separation depends primarily on the characteristics of the bubble population generated in the machine and its distribution and flow throughout its volume. The formation and separation of bubble-particle aggregates create two zones, with strong interactions between them, and with markedly different hydrodynamics conditions. A model describing two-phase hydrodynamics of the continuous and dispersed phases (frother solutions and bubbles, respectively), moving along the whole unit, is proposed. Bubble populations are characterized at the formation stage including the effect of the presence of frothers. Flow through the aggregates formation zone, where bubbles move freely and are closely spherical, is modeled using drift-flux analysis. In the aggregates separation zone, bubbles initially pack maintaining a water layer thick enough to prevent capillary forces to affect their shape. As water drainage proceeds, bubbles deform, capillary channels form, and a network of channels with a diameter size distribution develops; channels become narrower (permeability is reduced) as the distance from the interface increases. Froth hydrodynamics is characterized using models originally developed to describe unsaturated flow through porous solid particle beds. Effects of hydrostatic pressure are considered.

Jan 1, 2014

By J-P Franzidis, P. O. Gyebi

"Coal-water mixtures (CWM) of concentrated fine coal may be transported in pipelines but this is influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. The objectives of this study are to investigate the importance of surface charge, solids concentration and dispersant addition on the rheology and stability of a fine Witbank coal-water mixture (<75 m). Zeta potential, rheology and stability were measured with a Malvern Zetasizer, a AR1500EA rheometer and a static rod penetration test, respectively. Sendep 30D, Sendep 30F and Norilose 8058, all supplied by Senmin International, were used as dispersants, at dosages of between 0.1 to 0.5% dry coal (w/w). Solids concentration was varied from 10 to 58% (w/w). The zeta potential was found to be positive at low pH and decreased sharply with increasing pH to a minimum of -50 mV at pH 10. The zeta potential decreased with increasing dispersant concentration for all dispersants. The lowest zeta potential of -63 mV was obtained for Norilose 8058 at a dosage of 0.3%. CWM rheology was Newtonian at lower solids concentrations but became non-Newtonian at solids concentrations over 40% (w/w), with an initial yield stress and pseudo plastic behavior. The yield stress decreased sharply with increasing dispersant concentration for all dispersants. The lowest yield stress was obtained for Norilose 8058. The addition of dispersants resulted in significant improvements in stability. A penetration ratio of over 70% was obtained for Norilose 8058 after 10 days. In summary, the addition of dispersants resulted in a decrease in the zeta potential which increased the electrostatic repulsive forces between particles, thus improving both CWM rheology and static stability.INTRODUCTION Coal Water Mixtures South Africa’s energy economy depends heavily on coal. It accounts for about 70% of primary energy consumption, 93% of electricity generation and 30% of liquid petroleum fuels (Eberhard, 2011). The transportation of coal to export markets and power generation stations is a problem in the South African coal industry due to ageing and inefficient rail infrastructure. This problem is intensified by the long distance of coal haulage, delays in the time required to load and unload wagons, and environmental challenges related to air pollution and water contamination. Fine coal may be transported more efficiently and economically in a pipeline as a highly concentrated coal water mixture (CWM). Typically a fine coal CWM will contain 60-75% coal, 25-40% water and nearly 1% of dispersing additives (Atesok et al., 2005; Dincer et al., 2003). However, the transport of CWMs in pipelines is strongly influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. These quantities are affected by the coal composition/mineralogy, solids concentration, particle size and size distribution, particle shape, inter-particle forces and dispersant type and dosage (Laskowski, 2001)."

Jan 1, 2018

By P. K. Fedotov

At projecting mining-concentrating complex at the deposit ?Zapadnoye? (Russia) it was considered to enable an opportunity of refusal from conventional SAG-mills. First time a scheme of gold bearing ore destruction using Roller Press RP 5-100/90 had been developed and integrated. The plant was launched in summer 2003 and presently it has achieved designed technological parameters, processing throughput comes to 1 million tons of the ore per year.

Jan 1, 2014

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

In the leaching of gold in aqueous cyanide solutions the rate of gold leaching may be decreased by the passivation of the gold, that may however be prevented or reversed in the presence of lead species in solution. In the present study potentiostatic, potentiodyanamic and XPS (X-ray photoelectron spectroscopy) analysis were used to further clarify the action of lead ions on the anodic activity of gold in alkaline cyanide solutions. It was found that lead increased the gold dissolution rate as it deposited on the gold surface at potentials more positive than its reversible Nernst potential for bulk metal deposition, i.e. by underpotential deposition mechanism, but that it decreased gold activity if present as bulk plated lead on the gold.

Jan 1, 2003

By I. Ngoma, Marijke Fagan, Susan Harrison, Rebecca Chiume

"Heap bioleaching is an unsaturated hydrometallurgical extraction process which is commonly applied to the recovery of copper from low grade sulfide ores as well as for preparatory treatment of gold ores. The leaching reactions occur in the liquid phase, catalysed by iron and/or sulfur oxidising micro-organisms. Contact of the mineral grains with the leaching solution is consequently essential for metal recovery. Additionally, the liquid is responsible for the transport of the liberated metal out of the heap under gravitation-driven flow. However, the highly inhomogeneous structure of the heaps coupled with low irrigation rates cause the flow to vary between being gravitationally and capillary dominated, resulting in non-uniform wetting of the ore. In this study a 132 kg agglomerated ore ‘slice’ is used to examine the effect of liquid distribution on microbial colonisation and mineral recovery in a long term bioleach (> 500 days) when irrigation from a single drip emitter source is employed. The novel setup enabled sample collection from ports positioned along the length and height of the ore bed, so that 2D maps of the degree of wetting and microbial colonisation could be generated at different times in the leach. Lateral movement of the liquid increased with bed depth; the majority of flow was below the irrigation point while the top corner of the bed that was not irrigated remained the driest region of the heap throughout the experiment duration. The lowest cell numbers were also recorded in the driest regions. Specifically, cell numbers in the top corner of the bed, 400mm from the irrigation point, remained at undetectable levels until the 283rd day measurement, in line with typical heap operation durations. This indicates that slow colonisation of the heap in the regions between irrigation points may be a significant issue in heap optimisation."

Jan 1, 2014

By Zhazira Baltabekova, Nina Lokhova, Arailym Dukembayeva, Madali Naimanbayev, Zhantore Dzhurkanov

"Recycling of industrial waste provided they have enough valuable elements requires significantly less investment compared with ore processing. Promising man-made raw material of rare earth elements (REE) is phosphogypsum. Works performed on dismantlement of phosphogypsum only concern phosphogypsum processing from apatit. In this case, none of the developments was tested for phosphogypsum produced on the basis of phosphorus, chemical and mineralogical composition of which is markedly different from apatites. We studied phosphorites of the Karatau deposits (Kazakhstan). Mineralogically all the layers are composed of three main ingredients: phosphate, silica and carbonate, which account for 92-96% of the weight composition of ores and rocks. Of impurities there are pyrite, iron hydroxides, gypsum, fluorite. In addition to the actual composition of phosphate in phosphate ores there are apatite. Silica is presented by chalcedony and quartz, and carbonate by calcite and dolomite. The results of X-ray microanalysis showed point cluster of grains containing REE in samples of phosphate ore. Analysis of the grain showed that REE are in the form of phosphates and silicates, which according to numerous studies in apatites is not established. In this regard, phosphogypsum, waste of production, is different in composition too. Therefore, transfer of techniques proposed in the methods for extracting REE from phosphogypsum after processing apatite, did not give the stated results and required a new approach to solving this problem. It should be noted that the phosphogypsum produced by processing the Karatau phosphorite contains medium group of REE by 2.6, and heavy group by 7.8 times more than phosphogypsum from processing the Kola apatite. Given the shortage of medium and heavy REE research to develop ways to extract the lanthanides from phosphogypsum after processing phosphate rock is promising. The study contains results of studies on the extraction of REE from phosphogypsum after Karatau phosphorite processing."

Jan 1, 2014

By Michael. H. Moys, Clayton Bhondayi

An electro-resistive measuring technique developed by the authors was used to study the effects of superficial gas velocity and froth height on froth phase bubble sizes as a function of height above the pulp-froth interface. Flotation tests and the bubble size measurement were carried out in a laboratory mechanical flotation cell that was operated in a pseudo-steady state mode using primary rougher tailings slurry from Lonmin Platinum as feed. The values of intra-bubble impact distances (IIDs) which are the estimates for froth phase bubble sizes obtained from the measurements indicated that as superficial gas velocity was increased, the values of IIDs decreased for the two froth depths tested. Increasing froth height at fixed gas rate resulted in an increase in IID values especially close to the froth surface. Changing froth height and gas rate alters froth residence times; longer froth residence times mean more time for bubbles to coalesce hence larger values of IIDs and vice-versa.

Jan 1, 2014

By S. Owada

A national project of ?Establishing ?Green-Hydrogen (G-H)? Society in Honjo-Waseda Area? is now being developed by Waseda University together with four other universities and ten companies. The project involves three tasks of technological development of, (1)?G-H? production, (2)?G-H? refining, transportation and storage, and (3)?G-H? utilization. This paper focuses the first task of ?G-H? production from aluminium dross. We developed the physical treatment process by combining selective grinding with vibrating rod mill and electrostatic separation, in order to produce two kinds of materials, one is metal aluminium concentrate to recover it and the other is raw material to produce ?G-H? and aluminium hydroxide which can be generated by the treatment with sodium hydroxide aqueous solution. Here, we described the concentration mechanism of metal aluminium in the selective grinding and electrostatic separation and proposed a separation flowchart for optimizing the ?G-H? system in Honjo-Waseda area.

Jan 1, 2014

By H. Koca, D. O. Aksoy, S. Koca

"In this work, modelling of galena flotation from a disseminated Pb-Zn ore containing 0,83 % Pb was investigated. In the flotation experiments, collector type and amount, frother type and amount, particle size, pH and flotation time were kept constant while solid ratio and depressant dosage were varied. The varied parameters are described with a mathematical model by using statistical design method. Central Composite Design method which is one of the principle response surface methodologies was used in statistical design and analysis of experimental results and process modelling. Two quadratic mathematical models were developed for Pb grade and Pb recovery. Analysis of variance showed that models obtained for Pb grade and Pb recovery were found to be statistically significant in 95 % confidence level. Predicted vs actual values of Pb grade and Pb recovery were also given in graphically. It was found that predicted values represent approximately 96 % and 94 % of actual Pb grade and Pb recovery, respectively. The high values of R-square (R2) indicate that the models developed for two response variables are powerful. INTRODUCTION Lead and zinc metals are widely used in electrical, mechanical, military, metallurgical, chemical, light and medical industries. Sulfide ores are the main resources for lead and zinc minerals (Luo et al., 2016). Froth flotation is the main beneficiation method to achieve lead and zinc sulfide minerals separation. There are two basic approaches to obtain lead and zinc separation by flotation. First, flotation of lead sulphide is carried out and zinc sulphide and gangue minerals are depressed by various depressants and second, the bulk flotation of lead and zinc sulphide is carried out to obtain a concentrate of lead and zinc, followed by the lead and zinc separation. (Yuan et al., 2012). Apart from concentration of lead and zinc by flotation, there are a few literature that reports concentrations of lead and zinc by gravity and hydrometallurgical methods with remarkable success (Goktepe, 2005; Yanbo et al., 2016)."

Jan 1, 2018

By Fatemeh Saeidi, Malcolm S. Powell, Mohsen Yahyaei

In order to deal with the problems of existing comminution models a new approach towards the development of mechanistic models has been made so as to better understand the physics of milling processes and environments. Despite enormous improvement in this field a comprehensive study of rock breakage characterisation, appropriate for use in these types of models, is still scarce. This paper reviews the existing models of comminution according to ore characterisation techniques and parameters. The authors have looked into the existing testing methods and their applied mechanisms of breakage, using standard test results available at the JKMRC. The study includes classifying testing devices such as the drop weight tester, rotary breakage tester, slow compression, and piston and die based on the few major fundamental mechanisms of breakage that are experienced by rocks in the breakage process. The paper compares the range of particle size and energy utilisation, applied strain rates and loading mechanisms for the equipment. The product size distributions from the various equipment is compared for equivalent input energies, various loading rates but the same level of energy intensity, a broad range of energy including low energy utilisation and fines generation rate for equivalent specific energy input. The results clearly show that the outcomes and conclusions on competence and energy for breakage are a function of the test method that is applied. In ongoing work, it is proposed to investigate common tests that can be applied to characterising ores in a manner suited to modelling a range of comminution devices.

Jan 1, 2014

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, J. Taguta

The adsorption of heterocyclic collectors such 2-mercaptobenzothiazole (MBT), 2-mercaptobenzoxazole (MBO), 2-mercaptobenzimidazole (MBI) and their derivatives on pyrite form a basis in understanding the flotation reactivity that may be applicable in a wide range of sulphide minerals. This study uses a computational and experimental approach to determine the heat of adsorption of MBT, MBO, MBI and modified MBT collectors onto pyrite surfaces. Computational calculations found that the adsorption energies were in the order: MBO > MBI > MBT. The heterocyclic collectors were adsorbed in their thiolate form on the surface. In the case of the pyrite (100) surface, the MBT adsorbed through the exocyclic sulphur atom, while MBO and MBI adsorbed through the exocyclic sulphur and N atoms onto the 5-coordinated Fe atom. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted, where the MBT exocyclic sulphur atom bridged on the 5- coordinated Fe and surface 2-coordinated sulphur atoms, while the N atom adsorbed on the 5-coordinated Fe atom. In the case of MBO and MBI, dissociation of the exocyclic sulphur atom from the collector occurred with subsequent interaction with the surface 5-cordinated Fe and 2-coordinated S atoms. This resulted in the collector carbon atom adsorbing on the surface 2-coordinated S atom, while the N atom adsorbed on the 5-coordinated Fe atom. The adsorption of the modified MBT was found to be more exothermic than the MBT, which showed that introduction of a –CS2 group on the exocyclic sulphur atom improved the affinity of MBT on the surface, and was thus a better flotation collector. The computational results were supported by experimental enthalpy of adsorption measurements and microflotation tests. The chemistry of the heterocyclic thioamides is complicated by the fact that they can exist in a number of tautomeric and ionic forms at different pH’s. This is discussed in relation to the flotation and calorimetric data.

Jan 1, 2018