Search Documents

By N. J. Bolin

The Aitik copper mine is located in the north of Sweden and the concentrator at the mine started its operation in 1968 with a capacity of 2 Mton ore per year. Since then the operation has expanded several times, and today the capacity is 18 Mton ore per year. A new expansion plan was investigated in 2005, however the building of a new concentrator was found to be a better solution, giving a lower cost, a longer lifetime and more concentrates to the smelter at the coast. Several choices have been evaluated regarding the location of the concentrator?s crushing, grinding, dewatering, process control and water systems. The energy cost comparison has been an important factor when evaluating the various choices. The single most important decision has been in choosing the grinding system. Once again the fully autogenous grinding system, favoured by Boliden, has proven to be the best solution. The location of the mill, high and near the tailing pond, gives lower transportation costs for the ore and tailings, compared to other locations. A new water system will lower the pumping cost, give better control of water circulation to the plant and create fewer problems with permafrost in the tailings disposal area. Molybdenum recovery will be installed in the new plant using a separate circuit. A gold leaching plant was also investigated. Gold leaching is planned for the pyrite concentrate from the chalcopyrite/pyrite separation and the concentrate from the desulphurisation circuit that will be installed on the bulk flotation tailings.

Jan 1, 2014

Calcium carbonate has three polymorphs: calcite, aragonite, and vaterite. Needlelike aragonite CaCO3 with a high ratio of length to diameter (aspect ratio) is widely used in plastics, rubber and ceramics as a filler and in pigments and paints as a carrier. This paper investigated the influence of H3PO4 dosage, reaction temperature, CO2 flow rate, and initial Ca(OH)2 concentration on formation of needlelike aragonite CaCO3. It was found that the presence of H3PO4 in Ca(OH)2 suspension resulted in rapid formation of (Ca5(PO4)3(OH)) crystal nuclei, which facilitated nucleation and growth of aragonite CaCO3 on the formed (Ca5(PO4)3(OH)) crystal surfaces. The results revealed that H3PO4 addition of P/Ca of 0. 2~0. 3, high temperature of 75~85 °C, low CO2 flow rate and initial Ca(OH)2 solid concentration of 1. 5 %~5. 6 % are beneficial to formation of aragonite. Well crystallized needlelike aragonite CaCO3 whiskers with length > 20 µm and aspect ratio > 15 were directly synthesized.

Jan 1, 2014

By D. Tao

A novel rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features, including a high efficiency rotary charger, charger electrification, laminar air flow, etc. A parametric study has been performed with a coal combustion fly ash sample to investigate the effects of major operating parameters on the process performance. Most significant operating variables and optimum conditions were identified. Separation tests performed with four fly ash samples indicated that the rotary triboelectrostatic separator showed effective fly ash separation.

Jan 1, 2014

By S. Safak

Europe retains a modest position in world mining activity in terms of scale of production and mineral reserves but maintains a non-negligible role in the world mining industry. The concept of sustainable development resting on three pillars of economics, environment and social development has become an increasingly important factor in the European mining sector and a major influence on the related policies of the European Commission. Members of European mining industry shall conduct their activities according to the principles which promote sustainable development. A successful minerals planning policy should create the legal administrative environment that is necessary to ensure the sustainable supply of minerals to society within the framework of sustainable development. Members of the European mining industry shall conduct their activities according to principles which promote sustainable development. The challenge for sustainability is to find a balance between securing minerals supply, protecting the environment and achieving social progress. The point of balance depends on the range of policies adopted by governments. In this paper the development of the sustainability of the mining sector in EU and the social component of sustainability in the mineral industry is discussed.

Jan 1, 2014

By J. P. Dai

The Fankou Mine in Guangdong province, China, processes a polymetallic ore containing averagely 4.2% Pb, 8.5% Zn, and 90 g/t Ag. The main metal minerals including sphalerite, galena and pyrite are very finely disseminated and unevenly occurred in the ore, making it difficult to liberate them from each other. This paper presents the processing technology of the Fankou plant and the characteristic features of the novel technology applied.

Jan 1, 2014

By Z. Q. He

This paper introduces the structure and working principle of SLon magnetic separator that has excellent performance in iron removal, and summarizes a part of the examples of applications, which applies this machine to remove iron from non-metallic ores, and shows widespread prospect of application of this machine in the purification of non-metallic ores.

Jan 1, 2014

By Arkady Senchenko, Yevgeny Zhagun, Yury Kulikov, John Starkey

"The paper contains description of a new project in Russia - gold-processing plant at Aleksandrovskoye deposit (start up in September, 2013). The paper includes a brief description of plant flowsheet, data for material composition and technological properties of ore, as well as information about the achieved parameters of ore processing over the first months of plant operation. The project is interesting because a new semiautogenous mill and a ball mill were purchased on the basis of SAGDesign Consulting Group recommendations after the testing of ore samples characterizing the deposit according to specific years of operation. The plant has relatively small design capacity - 750 000 tpa, but nevertheless is the biggest gold-processing plant in the territory of Zabaikalsky region. Major valuable component in the ore is gold, silver is recovered as a by-product. The ores are very hard to grind. The design grinding flowsheet includes a semiautogenous mill operating in closed circuit with a screen, and a ball mill operating in a closed circuit with hydrocyclones (SAB). Process technology includes gravity processing and flotation with subsequent cyanide leaching of concentrates. Mill operation analysis and conclusions about the compliance of the achieved values to target ones are shown, as well as the accuracy of SAGDesign method when applied to very hard ores of Aleksandrovkoye deposit are presented in this paper. Basic directions of technological flowsheet optimization are also given."

Jan 1, 2014

By Gaom M. W.

The Mount Isa copper concentrator started operation in 1973. Its secondary grinding circuit consisted of two 5 meters diameter ball mills in closed circuit with 505 mm cyclones. At the design throughput of 800 t/h, the 80% passing size of the circuit product (P80) was about 140 µm. The then Mount Isa Mines Limited (?MIM?) installed two autogenous grinding (?AG?) mills in 1991 to replace two stages of crushing, a rod milling stage and one primary ball milling stage. One of the AG mills was later converted to semi-autogenous grinding (?SAG?) operation by the addition of a steel grinding medium to achieve the designed plant throughput of 800 t/h. The cyclone over-flow P80of the secondary ball mill circuit was reduced to 120 µm by the increased operating power in the AG/SAG mill circuits. The two secondary balls mills had a grinding power of 5.2 MW. A mineralogical study of the milled products indicated that half of this grinding power was sufficient for adequate chalcopyrite liberation. Eliminating one of the secondary ball mills could reduce energy and operating costs by more than A$2 million dollars per year. An optimisation project team was established to achieve the predicted power saving. Grinding circuit simulations were conducted for different circuit configurations. Ball mill parameters such as ball size, ball charge and feed slurry density were optimised. Cyclone body diameter, spigot and vortex finder sizes, and cyclone types were tested. The secondary ball mill circuit was redesigned and several proposed circuits were run as trial production campaigns to determine their operability and efficiency. The plant trials confirmed that one of the secondary ball mills could be decommissioned. Significant cost savings were achieved as a result. The success of the project demonstrates optimising grinding circuits can not only deliver the plant performance, but also a much lower unit operating cost through energy and maintenance savings.

Jan 1, 2014

By P. A. Bepswa

A numerical study done to test the efficacy of heuristics developed for the design of measurement networks for high precision metallurgical accounting is presented in this paper. The heuristics considered were designed to maximise variance reduction of terminal stream measurements through data reconciliation for observable linear flow systems. A complex metallurgical process flow sheet from the mineral sands industry was used as a case study. Monte Carlo type simulations coupled with a non-linear programming based steady state data reconciliation algorithm were used as tools to investigate the heuristics. The results obtained suggested a close correlation between magnitudes of measured variances and the respective levels of variance reduction obtained through data reconciliation for both internal and terminal streams. It was observed that variance reduction through data reconciliation was maximised for terminal stream measurements in networks characterised by high precision measurement of internal streams and/or in flow sheets characterised by high ?stream to node ratios?. Terminal streams attached to highly interconnected parent nodes were observed to experience higher reductions in variance compared to terminal streams attached to less interconnected parent nodes. The results generally highlight the additional benefits of highly interconnected flow sheets and high precision internal stream measurement regimes on the maximisation of variance reduction of terminal stream measurements through data reconciliation. These findings are significant to metallurgical accounting and to process accounting applications in general in that they provide a conceptual basis for design decision making regarding the construction of measurement networks aimed at maximising variance reduction of targeted streams through data reconciliation.

Jan 1, 2014

By A. Shandilya

ACC ECOSAND is finely powdered crystalline silica, which can replace natural sand usage in concrete and plasters. ACC ECOSAND ensures a comparatively denser concrete than those made only with natural sand and / or quarry fines / Manufactured Sand (Artificial Sand). Moreover, there is a significant gain in compressive strength (10-15 %) & durability in concretes (Reduced chloride conductivity leads to increased durability). ECOSAND is a by-product of froth flotation of limestone. At ACC Madukkarai cement works, Coimbatore, Tamilnadu, full-fledged mineral beneficiation process is adopted to enhance the usage of flotation reject in concrete and plasters. Optimum level for usage of ECO-SAND is 50%. With 50% usage of natural sand+50% ECO-SAND in concrete mix, 1 day, 3 day, 7 day & 28 day compressive strength is increased by 30.1 %, 22.6 %, 15.1 % & 11.0 % respectively and with moderate chloride permeability as compare to 100% Natural Sand. Keywords: froth flotation process, beneficiation studies, Denver cell, ECOSAND, siliceous material, durability & compressive strength, RCPT

Sep 1, 2012

By A. V. Kanarskay?

The research is aimed at involving in the processing of poor platinummetal natural and technogenic raw materials. The purpose of the research is the creation of a multifactorial complex of innovations in the system of ore preparation and separation cycles, which ensure a high efficiency of flotation enrichment of hard-to-treat raw materials. In the usual practice of enrichment, minerals of the platinum group (PGM) of less than 10 microns in size are the source of inevitable process losses. For poor raw materials, it is precisely thin PGMs that are characteristic, their proportion sometimes being almost 100%, and their opening leads to the formation of a large amount of slime, which adversely affects the efficiency of flotation. To reduce the yield of slimes and increase the selectivity degree of the opening of the PGM in the ore preparation cycle, a dry grinding scheme and pneumoclassification of the milling material has been developed to obtain fractions of different fineness, density and morphology of the particles. From 2 to 5-fold reduction in the yield of slurries for various ores has been achieved. The separation cycle successfully tested are: flotation of fractions in separate cycles with a differentiated choice of the reagent regime; preliminary selective flocculation of slime fraction material; use of a new generation of bioreagents for flocculation and flotation. A new approach to subsoil research is protected by a patent. The dependence of the efficiency of biocollectors on the composition of biomineral extract from the processed raw materials, which forms the basis of new reagents, is established. The possibility of obtaining the degree of extraction of PGM, native gold and sulphides from finely ground pre-fractionated poor ores with the use of biocollectors of at least 85% is proved. With conventional reagents, the extraction of PGM is 12-23% lower, with the use of traditional ore-preparation apparatuses, the PGM recovery rate was halved. Methods for the long-term storage and preparation in industrial conditions of biocollector reagents that do not require the purification of waste waters from them have been developed. The developed multifactorial system of intensification of flotation enrichment can be introduced to recovery PGM from tailings of enrichment of titanomagnetite, chromite and copper-nickel ores.

Jan 1, 2018

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors is the widely used technique. CPS has certain limitations: a) inability to recover certain oxide Cu minerals because they are refractory to sulfidization, b) high consumption of NaSH (or Na2S), and c) potential health and safety hazards associated with NaSH (and Na2S). Flotation of oxide copper minerals using alkyl hydroxamate (AHX) collector has been studied extensively. Investigations using single minerals and laboratory ore flotation have been conducted in the past to demonstrate the efficacy of alkyl hydroxamates. The technology has been used intermittently in plants. One of the main challenges in plant use has been quantifying the true potential for alkyl hydroxamates for recovery of various oxide Cu species in complex and variable ore systems and identifying the most suitable conditions for optimal use. Quantitative mineralogical analysis using QEMSCAN was used in this study to characterize flotation products lab flotation samples. Analysis of concentrates and tails from hydroxamate flotation and CPS flotation stages demonstrated that certain oxide Cu minerals respond exclusively to alkyl hydroxamates and not to CPS. The hierarchy of interaction of AHX with the various oxide Cu minerals could be inferred from these studies. Finally, these studies also allowed quantification of a group of minerals species, which (erroneously) report as part of the Acid-Soluble Cu [ASCu] but cannot be recovered by flotation, thereby facilitating an estimation of the true recovery potential for alkyl hydroxamate.INTRODUCTIONCopper that is economically recoverable occurs in three major types of ores, which are defined by the modal mineralogy of Cu. For sulfide ores, Cu occurs as sulfide minerals and is satisfactorily recovered by flotation using sulfide collectors. Non-sulfide ores, which contain Cu in the form of oxides, phosphates, carbonates and silicates, described in the industry as “oxide” ores (or ores containing “acid-soluble” Cu or ASCu), are currently treated using hydrometallurgy, which involves leaching with dilute sulfuric acid followed by solvent extraction and electrowinning, unless the ores contain acid consuming gangue minerals such as dolomite. For mixed sulfide-oxide ores (i.e. containing both sulfide and oxide Cu minerals) that do not contain acid consuming gangue minerals, Cu values are easily recovered by flotation of sulfide Cu minerals followed by leaching of oxides (only when a leach plant is available). However, when the ore contains acid consuming gangue minerals flotation is required to recover both sulfide and oxide Cu minerals."

Jan 1, 2018

By J. Faitli

The Lake Balaton is the biggest and for many reasons the most important lake in Hungary. To preserve its healthy nature it is necessary to remove the accumulated mud time to time, similarly to the many living waters, lakes and rivers everywhere. Typical existing technologies (mechanical, hydraulic) require large depositional areas, where the removed slurry and mud is dewatered through very long time. One problem is the non existence of an economical mud thickening technology. Another major problem is that current methods remove the sand fraction with the mud as well. Many times sand has to be complemented from outer sources to endanger the natural balance of the living water. By the financial support of the NKFP 3A/068/2004 Hungarian Research Project our consortium has been looking for the solution to the above mentioned problems. The original ideas of the project were: 1. Sand should be separated and returned to the water by hydrocyclon; 2. New mud thickener should be developed based on the principle that vibrating rods can force settling and packing of mud particles. The work was started by fundamental research with different samples from Lake Balaton and River Bodrog. An automated settling column (45L) has been built for the investigation of the effect of vibrating rods on the settling behavior of suspensions. An optical sensor has been developed by with the settling curve (height of settling slurry as function of time) can be automatically measured. Different vibrating methods and parameters have been tested by the application of a linear motor and mechanical eccentric drive. On the basis of the fundamental research a new thickener, called the rod ? lamella thickener has been developed and an industrial size (50m3/h) mud removing technology has been built. Main parts of the technology are the traditional dredging barge and the thickening technology. The thickening and sand separation technology is tugged by the dredging ship. Its main elements are the homogenization tank, slurry pump, hydrocyclon and the rod ? lamella thickener. In this unit lamellas carry out pre-thickening, then vibrating rods further increase the concentration. The thickened mud is transported out by a screw - of which revolution number is precisely controlled - against a spring supported valve. Paper reports about the design, building, water probe and on-site tests of this mud removing technology. Two new patents had been presented, one is about the rod ? lamella thickener and the other is about the mud removing technology with sand separation.

Jan 1, 2014

By J. Botula

In the region of the North-Bohemian Coal Basin and its environment, there, in a row of places, are found the accumulations of rocks of the sedimentary and pyro clastic origin, the preliminary composition of those shows the possibility of their being utilized for the production of ecologically sparing natural Fe- and Ti- pigments and filling substances. In many places of the regions of Chomutov and Podborany and near Bilina and also in other places, there are found raw stocks perspective for the preparation of yellow up to ochre-brown, red, brown-red and green dyes. The target of project is the verification of dispensable reserves, their mineralogical composition and chemical and physical attributes, verification of treatment ways of Fe-and Ti-pigments separation (hydrocyclones, magnetic and electrostatic separation) and their stabilization and technological painting attributes for applications in colors, coating and plastic masses, mortar mixtures etc.

Jan 1, 2014

By G. K. Palshikar

Mining operations offer many opportunities for the use of IT and communication technologies to improve automation and thereby deliver higher levels of productivity, cost, quality and safety. In this paper, we discuss a particular application, namely, building a fully automated train control and operation system within a mining area. We first outline the basic architecture and functionality of such a system and then present a real-life case study where the railway system within a remote iron ore mine in Canada was converted to a fully automated train operation system. This hard real-time safety-critical system required the use of advanced technologies such as embedded systems (e.g., on-board train controller), radio communications, formal methods, optimal scheduling, and extensive simulations. We focus on the design aspects for maintaining the system in safe states.

Sep 1, 2012

By Y. B. Zhang

China is rich in iron ore resources, but most of these ores are low-grade, polymetallic and refrac-tory ones. Furthermore, with the rapid development of chinese iron & steel industry, the comprehen-sive recovery of these ores is becoming more and more important. The tin, zinc-containing complex iron ores are typical polymetallic and intractable ones, and great reserves of them are found in China. At present, they have not been efficiently utilized. In this paper, based on the investigation of basic physicochemical properties of the tin, zinc-bearing iron concentrates, taken from a mineral processing plant, the mineralogy reason that these concentrates are so intractable and refractory is found out, using advanced microscopic testing methods, such as optical microscope (OM), Scanning Electronic Microscope (SEM), X-ray diffrac-tion (XRD), etc. It is found that the symbiotic relationship of iron, tin and zinc metallic minerals are very complicated, and magnetite in the concentrate is closely symbiotic or enwrapped by fine cassi-terite and sphalerite. So it is difficult to separate tin and zinc completely from the iron concentrates by simple regrinding and physical separation method. This investigation provides theoretical guid-ance for developing new approaches for utilizing these concentrates.

Jan 1, 2014

By S. M. Saghaeian

The studies on the product finer than 12 mm due to crushing and sizing plant of Gol-e-Gohar Iron Ore mine showed which this material contains significant amount of valuable iron minerals. Based on the carried out experimental studies on representative samples of fine hematite iron ore, a processing flow sheet was designed to upgrade iron content. This plant is known as first hematite iron ore enrichment plant in Iran which the dry medium intensity magnetic separators (with magnetic field intensity 4500 gauss and high gradient) has been used. The main objective of the plant is production of high iron product with iron content more than 61% and weight recovery more than 55% from the feed with iron content of 54%. In this plant, at first material are screened by a single deck screen (6mm), then oversize particles is separated at one stage by magnetic separator, while undersize ones at two stages. Based on the results of experimental tests, a final high iron product with iron content of 62.4% and weight recovery 63.9% can be achieved. It should mention which the iron content can be enhanced through increasing the speed of magnetic separators especially at the part of separation of finer iron ore.

Jan 1, 2014

By S. H. Morar

Froth stability is widely recognized as a key driver of flotation selectivity. It is well known that froth stability is affected by the type and quantity of surface active reagents present (frothers), and the concentration and hydrophobicity of solid particles present. While some studies have been performed on the effect of frothers on froth stability in three-phase systems and the hydrophobicity of particles present, very little work has been performed on the effect of solids loading on froth stability. This may be due to insufficiently robust measurement techniques. This paper investigates the use of a new machine vision measurement to measure solids loading, and the relationship between this measurement, bubble size, and bubble burst rate on the froth surface. Keywords: froth flotation, machine vision, solids loading

Sep 1, 2012

By T. Onnela

Metso Mining and Construction Technology is one of the world leading suppliers of equipment and knowhow for aggregate and mining industry. The processing capacity, ease of use, and reliability are featuring Metso?s state-of-the-art cone crushers. Crushing is a complicated process affected by numerous parameters. The optimized crusher kinematics is one of the key factors for high performance. To fine tune the crusher kinematics and crushing chambers one needs to know how different parameters affect. The main cone crusher parameters are head angle and diameter, gyration point, shaft speed, eccentricity, stroke length, and inclination and design of crushing cavity. Selecting the correct combination of these parameters is a multi task optimization challenge. In practical life there are more factors to achieve satisfactory performance, like crushing chamber wear and profile management keeping the performance constant over the whole wear life, control of crusher frame loads, ability to handle disturbances in feed material etc. The extensive research work has lead to a solution that enables the highest possible material density in the crushing chamber. This design provides maximum reduction of processed material and thus increased share of 0/10 mm product. High density in the cavity offers further benefits, such as high throughput capacity, less material contact with wear parts and even load on crusher frame and bearings. The challenge that an equipment supplier involved with high density crushing is how to design a robust cone crusher, which is able to cope with the high crushing forces due to high resistance from the crushed material against the gyration movement. Metso has launched a new series of cone crushers HP3, HP4 and HP5 that are all able to work in high density crushing applications The test results and evidence from over 300 installations clearly prove the effectiveness and importance of high density crushing. Keywords: cone crusher, crushing chamber, crusher kinematics

Sep 1, 2012

By L. Y. Feng

The percentage of leached zinc in massive zinc oxide ores (11.7% Zn, >2 mm) is up to 73.3 % in 120 days. Alternatively, crushed to -0.154 mm, mixed with cement 5% (wt), pelletized and solidified. The diameters of the pellets obtained are between 5 mm to 8 mm. When the pellet solidification periods are 3 days, 10 days and 45 days respectively, the alkaline leaching rates of zinc in the pellets are up to 95.8%, 89.1% and 76.4% respectively. Decreasing the solidification time can re-duce reaction time, increase dissolution of zinc in pellets and lower the effect of initial zinc concentration on leaching rate. The experiment results show that the minimum solidification time is three days, and the kinetic study indicates that alkaline leaching of the low grade zinc oxide pellets is controlled by the diffusion of the leach liquor through the gangue layer in the whole leach process, and the apparent rate constants are 3.33×10-2 day-1, 9.18×10-3 day-1, 5.82×10-3 day-1 respectively.

Jan 1, 2014