Search Documents

By M. Saghaeian, R. Hejazi, A. Dehghani Ahmadabadi, M. Zare

"In the most iron ore beneficiation plants, reverse flotation is the best method for removing silicate gangues from final iron ore concentrate. Many previous studies show, if the major portion of impurities include quartz minerals, the flotation process is simple, but if iron silicates are dominant, reverse flotation is so complicated and mostly not very effective. In this study which was performed on the Sangan iron ore concentrate, the performance using of reverse flotation and magnetic flotation separator for elimination of silicate gangues from the magnetic iron concentrate was investigated. The operational parameters for reverse flotation are considered as: collector and frother types and dosages and also modifiers. But for magnetic flotation separator parameters were magnetic field intensity as well as overflow and underflow water rates. Results showed that reverse flotation has not a significant effect on the elimination of impurities. Because of the silicate gangues of Sangan concentrate including a mixture of quartz and iron silicates (amphibole, pyroxene and feldspar), so downgrading of the SiO2 content for the flotation concentrate was rather low and only average reduces of 20.60% were possible. But the findings of using magnetic separator was more satisfactory. Results of the weight recovery, iron grade and also SiO2 and S grades of final concentrate were better with magnetic flotation device. So at the best and optimum condition, we could reduce 51.01% of the total silicate (SiO2~ 2.19%) along with 74.66% of sulfur content (S~ 0.076%) and concentrate weight and Fe recoveries of 92.04% and 94.51% respectively, final Fe grade of 68.73%.INTRODUCTION Chemical/traditional flotation is one of the most effective methods for separating valuable particles from waste minerals, which is used in most mineral processing industries. In the iron ore processing industry, the major impurities present in iron ore concentrate include sulfur, silica and phosphorus (Bruckard et al, 2015), which are often carried out by reverse flotation methods for the removal of sulfide and oxide impurities (Donald, 1967: Araujo et al., 2005: Ma, 2012)"

Jan 1, 2018

By Andrei Yevdokimov, Ivan Sidorov, Olga Lanchakova, Olga Khmelnitskaya, Tatiana Chikina

"The paper focuses on the results of the research on development of hydrometallurgical process of gold recovery from refractory sulfide flotation concentrates based on fine and ultrafine grinding. Refractory concentrates (the degree of refractoriness is 16.9%-82.6%) were chosen for testing. The efficiency of the process based on fine and ultrafine grinding to treat flotation concentrates with gold intergrown with sulfides and rock-forming minerals was shown. Based on the test work conducted, the process option was chosen. In included grinding of flotation concentrate to the size of 98% minus 20µm in a bead mill, lime treatment with air blow, CIL, filtration and detoxification of liquid phase of the slurry. This process (compared to the basic option) provides the recovery of gold from 82.6%, up to 94.0% and decreases the residual grade in the tailings from 3.3g/t to 1.1g/t at the consumption of 12.6NaCNkg/t. Based on the results of the test work and pilot plant testing, project design criteria of flotation circuit at a Russian plant was developed."

Jan 1, 2014

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By M. D. Amirova

Cyanide-free technology of complex copper-lead ores flotation may be improved through enlarged range of pH values, enhanced copper recovery into copper concentrates due to additional recovery of secondary copper sulfides, as well as through enhanced efficiency of lead sulfides depression in process of new flotation modifiers-based selective separation. Study of the effects of flotation modifier (of metal nature) on minerals surface conditions proved that the xanthate is practically not adsorbed on the galenite surfaces due to minerals hydrophilization. Joint effects of sodium sulfite and modifier enhance process conditions for intensive galenite depression and at the same time for effective chalcopyrite and chalcosine flotation within a large pH values range (from pH=8 to pH=10). Identified mechanisms carry inference that proposed chemical reagent treating method is very promising for selective copper-lead concentrates separation. Potential use of carbon-containing materials as zinc flotation modifier to enhancing zinc recovery in processes of lead-zinc ores treatment has been studied. In our flotation tests we used Shalkiya (South Kazakhstan) lead-zinc ores containing such impurities as carbon shales, which presence impedes the process of saleable concentrates production and gives rise to excessive consumption of flotation agents due to the xanthate adsorption on the carbon. Lead and zinc concentrates were produced by process stages as follows: ores milled to 95% Cl. -0.074 +0; lead and zinc roughing flotation and further recleaner and testing operations. Test flotation in open process cycle resulted in enhancing zinc recovery into zinc concentrates by 21.1% and increasing zinc content in zinc concentrates by 3.96% that evidences promising potentialities for use of carbon-containing products as additional zinc flotation modifier. Works were carried out under National Program 2003~2005 of fundamental researches ?Physical and Chemical Mechanisms of Interactions in Multicomponent Solid and Liquid Systems Specific for Integrated Processing of Complex Metal-Containing Minerals and Technogenic Raw Materials? and contractual Agreement 2005 Optimization of Production and Technology of Shalkiya Lead-Zinc Ores Processing at Kentau Dressing Works.

Jan 1, 2014

By Magnus Evertsson, Rebecka Stomvall, Josefine Berntsson

"Understanding the effect of particle shape on dry rheology is considered to be an important aspect in order to replace natural sand used in concrete with manufactured sand. Crushed particles from solid rock are normally less rounded and have less equally shaped dimensions compared to natural sand. Thus, the flowability and workability of the concrete will be different. In previous research, it has been demonstrated how different crushing techniques affects the shape of the particles. In many cases it is believed that Vertical Shaft Impact (VSI) technology is a way forward to replace natural sand. To be able to study the effect of VSI at the smaller fractions (63-2000 µm) sufficient measurements methods to determine particle shape are required. Optical tools to analyze the aggregates would make it possible to study a large amount of particles at small fractions. The determination of particle shape of aggregates is challenging since the shape is highly irregular and the size span of particles are very large. This study aim to evaluate one of the available optical tools, the Camsizer, for digital imaging determination of shape and size distribution. The available default shape parameters of the Camsizer are studied to understand the meaning of the parameters and their suitability for determining the quality of manufactured sand. To evaluate the capacity to determine particle shape, tests are made with 35 different materials. The results are compared with the dry rheology measured with the standardized "flow cone" test. Dependence has been previously proven between particle shape and the mass flow rate in the cone. Three different shape parameters, aspect ratio, sphericity and symmetry, are studied with the Camsizer and the results are compared with the mass flow rates in the cone. The results indicate a strong linear relationship between the optical parameters and the flow cone test."

Jan 1, 2014

By Christian O’Keefe, Alex Van der Spek

"Evaluation of inequalities of the partial sums defining cumulative grade and recovery prove that cumulative grade has an upper bound not dependent on the bank number and cumulative recovery possesses an upper bound proportional to the bank number. This explains one observed characteristic of cumulative grade versus cumulative recovery curves. The existence of such maxima combined with the observed shape of cumulative grade-recovery curves leads us to postulate that these curves can be well described by rectangular hyperbolae. Rectangular hyperbolae are characterized by asymptotes at right angles to each other. It is proven that this property can be used to derive an equation for the cumulative mass flow of the concentrate in terms of the asymptotic values of cumulative grade and cumulative recovery. Fitting hyperbolae to experimental cumulative grade cumulative recovery plant data then results in estimates of the maximum grade, the maximum recovery and a constant which may be taken as a performance coefficient of a row. Normalization of the cumulative grade and the cumulative recovery by their respective maxima gives rise to a graphical representation that can be used to evaluate the operating performance of a row of floatation bank cells. The normalization procedure removes the bias that is introduced by inevitable variation in mass flow of the feed and variation in feed mineralogy or feed particle size distribution. Reduction of the normalized data collapses all cumulative grade-recovery data onto one and the same curve. This removes the differences caused by the variation in row performance. The reduced cumulative grade-recovery data scatters around a common hyperbola. This can be used to gauge the validity of the assumptions made. Normalized cumulative mass pull is determined from the fitted values of the maximum recovery and maximum grade. This may serve as an alternative performance indicator of the floatation row."

Jan 1, 2014

By T. Fraszczak, U. A. Peuker, T. Mütze, T. Leißner, A. Wikedzi

The present paper highlights on the comminution and liberation properties of two greisen-type lithium bearing-mica ore blends (L1, L2) subjected to different breakage devices; cone crusher (CC), roller crusher (RC), rotor beater mill (RBM) and a screen mill (SM). The particle size distribution (PSD) of the products from each device were evaluated to search for an appropriate PSD model using Gates-Gaudin-Schuhmann (GGS) and Rosin-Rammler (RR) functions. In order to determine an appropriate function that could better describe the PSDs from the devices used, the coefficient of determination (R2) was used as a criterion. In terms of mineral liberation studies, due to costs, only products from rotor beater mill (RBM) were examined through an automated scanning electron microscope (SEM) technique. It was found that RBM, RC and SM products were better described by the RR model than the GGS model with higher R2 values (0.97-1.0). However, cone crusher products for L1 were better described by GSS model, while that for L2 were better described by RR model. In terms of the spread of size distribution as indicated by RR model parameters, RC products were more uniformly distributed compared to products from other devices, for both ore blends. Also the RBM products were more scattered than products from other devices. The results indicate that the composition of individual ore blends affected the comminution products PSDs since different PSD model parameters were obtained for samples comminuted by same devices. The modal mineralogy of the two ore blends indicate both to be rich in quartz, topaz, zinnwaldite and muscovite. Further, the result indicate that, for both ore blends, zinnwaldite phase is more enriched in the fraction < 250 µm. Moreover, better liberation of zinnwaldite is observed for L1 compared to L2. This could be explained by differences of the two ore blends in three aspects; the nature of mineral association, reduction ratio of the fractions analysed and the nature of spread of the size distribution.

Jan 1, 2018

By Samira Rashidi, Robert Dunne, Raj Rajamani

"High Pressure Grinding Rolls (HPGR) are known for more energy saving, better particle weakening and higher tonnage compared to semi-autogenous/ball mill circuits. These machines are scaled up based on the roll diameter. Therefore, studies in lab-scale HPGRs are always preferred because less weight of feed sample is required to run batch tests. The 50-hp laboratory-scale machine at the University of Utah is the first-ever lab-scale machine designed by late Prof Schönert, the inventor of HPGR. This 200x100 mm [DxL] HPGR is equipped with a robust data acquisition system, which enables running steady state tests using a feed sample as small as 6 kg to 12 kg. This paper presents the HPGR grinding study on two different categories of ores, one hard ore and the other soft. A test series has been performed to evaluate the energy consumption and the relation with size reduction on open multi-pass and locked-cycle HPGR circuits. The effect of feed size distribution and operating conditions has been investigated. Locked-cycle tests result in higher reduction ratio and higher rate of fines (100 mesh, 48 mesh and 28 mesh) generation when compared to open multi-pass tests. Data shows that scale-up trend lines stay consistent even when the circuit configuration and operating conditions are varied."

Jan 1, 2014

By Anand Anupam

Conventionally, beneficiation in Indian coal washeries is done using dense medium cyclones upto the size of 0.5 mm. Coal fines below 0.5 mm size are extensively cleaned by froth flotation. There are many problems associated with flotation of Indian coals, e.g. poor response of coal particles to flotation, misplacement of fine high-ash material to froth, loss of good quality coarser coals (within ?0.5 mm size range) to tailing streams, high cost of reagents, water contamination, etc. In addition, sophisticated control systems for efficient management of the fines washing circuits are needed. Thus, there is an escalation in the capital and processing costs. In view of these facts, studies were carried out to establish the cleaning potential of dense medium cyclones for beneficiation of fine coal down to a size of 0.1 mm, essentially aimed at reducing the load on fine coal circuits mainly comprising of flotation. ROM Coal (in the size range of -2 + 0.1 mm) obtained from JogtaOCM,Jharia coalfield possessing relatively low ash (about 21%) was used in this study. Purpose for using low ash coal was to further lower, its ash content down to 8% which is comparable, to the ash content of imported coal. After characterization studies, nine tests were carried out on the prepared feed sample for its beneficiation using a dense medium cyclone of non-conventional design (very low cone angle and longer barrel), by varying its apex and vortex finder diameters. The efficiency of separation has been evaluated using Tromp curves. It could be established that it is possible to produce a clean coal of 8% ash, with Ep value of 0.044, using Jogta OCM coal by treating it in a modified dense medium cyclone. These results are summarized and discussed in detail in the present paper. Keywords: dense medium, cyclone, fine coal, beneficiation, Jharia coal

Sep 1, 2012

By Erico Tabosa, Kym Runge, Peter Holtham

"The distribution of turbulence in an industrial scale mechanical flotation cell and its effect on flotation kinetics was studied using a fully instrumented 3m³ cell. The cell was operated at a copper concentrator in Australia with different combinations of airflow rates, impeller speeds and sizes and cell aspect ratio providing a wide range of hydrodynamic conditions. An analysis of the overall flotation cell performance showed that the overall copper recoveries were very similar for the conditions tested. However, by decoupling pulp effects from froth effects it was possible to evaluate whether the changes made affected the pulp zone and/or froth zone responses. The analysis showed that the overall recovery has the potential to be up to 7% higher, if not limited by froth recovery. The cell hydrodynamics were characterised by the overall energy dissipation rate and, to understand the distribution of turbulence within the cell, localised measurements were made using a piezoelectric vibration sensor. By comparing the metallurgical performance of the cell with the different hydrodynamic conditions it was found that the collection zone flotation rate constant was not directly related to overall energy dissipation, as is commonly observed at laboratory scale, where energy is usually only changed by varying impeller speed. In this study, energy dissipation rate was varied using not only impeller speed, but also the size of the impeller and the cell aspect ratio. In these circumstances, the best correlation was found to be between the collection zone flotation rate constant and the distribution of turbulence, i.e. the size of the turbulent zone."

Jan 1, 2014

By C. Stollberg

The recovery of valuable materials from electronic waste is of growing importance for the re-source management not only in the industrialized nations. Being a significant step in an innovative automated process for recycling of metals and plastics from used electric and electronic equipment, the results of the work introduced below, prove the applicability of microbial leaching of metals from printed circuit boards (PCBs) at industrial scale. Within the first project step, which started in March 2005, experiments in shaking flasks with a mixed culture of chemolitotrophic bacteria (mainly Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans) were carried out to study the solubilization of non-ferrous metals present in the electronic waste. It was found that the best results were achieved by means of a two-stage process in which leaching of these metals was carried out by acidified ferric sulphate solutions generated as a result of the prior bacterial oxidation of ferrous ions to the ferric state. Special reactor systems for bacterial generation of such solutions and for the subsequent leaching of non-ferrous metals from the waste were developed, constructed and tested under laboratory and pilot scale conditions. The optimum technological parameters such as concentration of iron ions, pH-value, temperature and presence of nutrients were established for both reactor systems. Parameters such as particle size, pulp density and flow rate of the suspensions being leached were established for the leaching process carried out under continuous-flow conditions. The complex flow sheet reflects a highly efficient technology on the basis of metal recovery, environmental effect and economical acceptance. The process was successfully implemented into an industrial demonstration unit.

Jan 1, 2014

By Filippov. L. O.

Metallurgical results for the copper-nickel disseminated ores were improved by using ultrasonic treatment. This has been demonstrated by processing of bubble-pulp flow in the reactor zone of a reactor-separator flotation machine. It can be explained by changes in mineral and size composition of the concentrates. Thus, the selectivity of Cu/Ni flotation for different values of the hydrodynamic parameter increases considerably. Additional effect of the ultrasound treatment has been noticed under conditions when the detachment of the gangue minerals from bubbles can be controlled. Reactor-separator has advantages over other types of flotation cells for this purpose. In fact, the weak diameter of reactors make more efficient the ultrasound effect than in conventional impeller or column flotation machines. A combination of ultrasonic treatment with original organization of gas pulp flux in the reactor-separator allows to obtain significant effects in the flotation attachment/detachment subprocesses, enhancing the process selectivity and/or recovery of substances. Increase of total recovery of copper and nickel into bulk concentrate at constant grade is 8.5% for coarse disseminated ores. For copper ore, copper recovery increased by 10% at unchanged grade of 11.7% and nickel recovery gained 17% at the constant grade of 2%.

Sep 1, 2012

By S. Titkov

At present, Russia is engaged in processing, 3new plants of hard-to-process potash ores with increased content (up to 10 - 12%) of insoluble impurities (insoluble residue ? I.R.). This required additional research to improve the process of potash ores flotation. Based on the study of the effect of dispersive properties of frother and its flow rate on the efficiency of aliphatic amines with different length of the hydrocarbon radical (as sylvite collector) there was showed the possibility to apply high molecular amine with length of hydrocarbon radical C20 ? C26 by normal temperature of circulated plant salt solution (saturated solution KCl ? NaCl ? H2O). There was designed and tested in plant conditions the modified amine collector with the length of the hydrocarbon radical C16 - C26, improving flotation of Sylvite under normal temperature of circulating salt solutions at potash flotation plants. There was made the study of the influence of the hydrocarbon radical length of alkylmorpholine on the Halite flotation from intermediate products of sylvite recleaner flotation with different content of I.R. (silicate-carbonate slimes), at normal and elevated temperature of salt solution. On the basis of the application of modified alkylmorpholine for Halite flotation, there was developed the process of further beneficiation for the intermediate products of sylvite recleaner flotation from potash ores with increased content of insoluble impurities, which can eliminate the circulation of the intermediate products in the process flow sheet of sylvinite ore processing and increase the KCl recovery into the finished product. Keywords: flotation, potash, halite, alkylamine, alkylmorpholine

Sep 1, 2012

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management.This paper describes the data integration requirements in a mine, concentrator and port for unification of the redundant data. The capture of the mining events, stock pile management and the metallurgical information is the base requirements for a dynamic environment to reduce the overwhelming amount of information to unified set of information. Part of any decision support program should entail these results to continuously improve the measurement system to address the costs in mine and milling the ore."

Jan 1, 2003

By M. Narasimha

The flow in a hydrocyclone classifier is highly turbulent complex nature of multi-phase structure, which has led designers to rely on empirical mathematical models for predicting the performance. A number of classifying cyclone models have been developed and successfully used in mineral comminution circuit simulators over the past four decades (Plitt, 1976 and Nageswararao, 1978). However, most of the mathematical models currently available to describe hydrocyclone classifier performance are based on single average mineral density component behavior. In industrial comminution circuits, the feed to the cyclone composed of a mixture of particles of varying degrees of liberation and sizes. The behavior of multi-component particles in a hydrocyclone is poorly understood and unaccounted for in most of the mathematical model equations available in the literature. There is evidence from a number of experimental data sets indicating the significant influence of the multi-component particles on measured cyclone performance. A concept for modeling the performance of hydrocyclones based on multi-component behavior is proposed in this paper. A set of semi-empirical model equations for cut-size, sharpness of separation are presented and the corresponding model parameters evaluated from the measured data are given.

Sep 1, 2012

By Ana Elisa Casas Botero

The Rhodococcus opacus microorganism was evaluated as a biocollector for flotation of barite. The electrophoretic behaviour of the mineral, before and after R. opacus interaction, was evaluated and showed that the cells adhesion shifted the mineral zeta potential curves. Adhesion tests were suggested a high affinity of the bacteria for barite. The experiments of the adsorption rate of the R. opacus on the mineral surface showed fast kinetics, achieving a maxim of cell adsorption after 5 minutes. Adsorption isotherm curves for barite could be categorized as Langmurian (L) type II. The best bioflotability results for barite achieved values around 75% for a R. opacus concentration of a R. opacus concentration of 250 ppm in the pH around 5.0. The studies were compared with the flotation of barite using a traditional collector. The bioflotation experiments were discussed considering the obtained adhesion tests. The results were supported by the Thermodynamic approach for selected pH values. The fundamental flotation studies showed the paramount potential that R. opacus presents as a biocollector and its possible application in the mineral flotation industry.

Jan 1, 2014

By Rod Hocking, Nenad Djordjevic, Randolph Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures of operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill.Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulated the assemblage of a physical mill."

Jan 1, 2003

By M. Guo

Coal-based Direct Reduction in Interior-combustion Shaft Kiln (CDR/ISK) is a brand-new technique. Compared with the traditional Coal-based Direct Reduction (CDR) technique, its main character is to use Interior-combustion Shaft Kiln (ISK) as the reactor of direct reduction. After being crushed and grinded, iron ore is made into green pellet, which will be surface-coated by coal fines. Then, the surface-coated green pellet can be directly reduced in ISK. The pellet should not be too dry and should be charged from the top of ISK. Oxygen-contained air should be blasted into ISK to keep the temperature in it higher than 1000 degrees centigrade, at which iron oxide will start direct reduction. The reduced pellet will be discharged from the bottom of ISK and after de-surface-coated, spherical Direct Reduced Iron (DRI) can be gained. The volume of carbon monoxide in the off-gas discharged from ISK is less than one per cent. By using this technique to get one tonne DRI, the consumption of coal is about 300kg of fixed carbon, which is much lower than the energy consumption by using other CDR techniques. There is a lot of complex refractory iron ore in China, which remains unexploited. The iron-bearing minerals in this kind of the iron ore can not be beneficiated economically by present technique of gravity, magnetic, flotation or magnetic roasting because the iron minerals are too very finely disseminated to be liberated, or, the iron minerals are too similar to gangue to be separated each other. By using CDR/ISK, complex refractory iron ore can be directly reduced in lower temperature and all kinds of iron mineral can be turned into iron metal. As the grains of iron metal growing larger during direct reduction, magnetic separation can be used to separate iron metal from gangue mineral, thus high-grade iron metal fines can be gained. According to the experiments, the grade of iron metal fines is above 90 percent and the recovery of iron is higher than 90 percent. The consumption of coal to process one tonne of complex refractory iron ore is only about 90kg of fixed carbon.

Jan 1, 2014

Three high-grade limestone ores (CaO content over than 53 %) with different geological origin have been characterized for the synthesis of aragonite precipitated calcium carbonate. Limestone ores examined in this study showed different crystal particle size that cause difference in disintegration degree and surface area of the synthesized slaked limes. The limestone ore with smaller crystal particle size showed higher disintegration degree and also yielded slaked lime with smaller surface area, which is good for the synthesis of aragonite precipitated calcium carbonate. The synthesis of aragonite PCC using the limestone with a small crystal particle size was yielded needle-shaped aragonite with the aspect ratio of about 14. Keywords: limestone, lime, slaked lime, precipitated calcium carbonate, aragonite, accelerated carbonation

Sep 1, 2012

By Kyoungkeun Yoo

A citric acid leaching test after heavy medium separation process was performed to remove the heavy metal contaminat such as Pb, Cu, and Zn from contaminated soil. The lead component was removed from soil by heavy medium separation whereas zinc component shows 0 % - 37.9 % removal ratio with particle size. The citric acid leaching was conducted to remove the remained zinc component. The removal ratio of Zn reached to more than 95 % under the conditions; 10 % in pulp density, 200 rpm in agitation speed, 50 °C, 2 mol/L in citric acid concentration at 2 hrs in leaching time. These results suggest that the heavy medium separation method followed by citric acid leaching is effective for treatment of soil contaminated with various chemical forms of heavy metal. Keywords: metal contaminated soil, citrate, heavy medium separation, zinc

Sep 1, 2012