Search Documents

By Roger E. Scholl

Data on off-site low-rise building damage from underground nuclear testing at the Nevada Test Site (NTS) of the United States Atomic Energy Commission (AEC) [The AEC has been called the United States Energy Research ant Development Administration (ERDA) since 1975, but because the data presented here were gathered between 1966 and 1970, the AEC rather than ERDA is referred to in this paper.] are available for seven large tests in the period from 1966 to 1970. The data, while sparse, provide an adequate sample for the investigation of motion-damage relationships. Damage in the study is statistically described in terms of the incidence of damage complaints, the incidence of buildings damaged, and damage cost. Using 5%damped response spectrum acceleration amplitude to characterize ground motion, the plotted data fit reasonably well with previous motion-damage relationships established from extensive data available from the 1969 RULISON underground nuclear explosion (UNE) experiment conducted in western Colorado.

Jan 1, 1976

By R Heater, G Glynn

Various small diameter commercial grades of slurry and emulsion explosives were tested and compared. Velocity diameter curves for confined and unconfined charges were established and the effects of temperature and hydrostatic pressure on critical diameters and minimum primer weights were determined.

Jan 1, 1984

By F. Malek

An extensive blast monitoring program has been carried out to study explosive performance and the effectiveness of blast designs in production blasts in a deep underground mine. Comprehensive monitoring of blasting vibrations through multi-station high-capacity high-frequency accelerometers, and borehole deformation history have been the main tools of such analysis. The mining activity involves relatively unstressed stopes as well as highly stressed stopes. More than 30 production blasts have been monitored, and the respective vibrations from close-range as well as distant seismic stations have been analyzed, and the vibration parameters (amplitude and frequency) have been correlated with explosive charge weight in the holes. It is found that the correlation between blasting rounds and the corresponding vibration amplitudes often have poor correlation for a very significant portion of the blasts. These point to either explosive charge malfunction in those specific blast holes, or inadequate blast design, or the effect of high in-situ stresses, or any combination thereof. This paper analyzes these variables and their effect on the overall blasting operation at the mine.

Jan 1, 2013

By Edward J. Jr Walter, Edward J. Walter

The vibration problem is approximately fifty years old. The original investigation of the U.S. Bureau of Mines was begun in 1930. Significant investigation into the problem was done by Crandell, Langefors, et al, Edwards and Northwood, and again by the Bureau of Mines. This resulted in an effective Safe Limit standard expressed in particle velocity as 2.0 inches per second.

Jan 1, 1979

By Robert B. Hopler

Explosives have been important to the oil and gas industries since the very earliest days. The first wells of Pennsylvania and New York in the 1860’s were able to be brought back to productivity by the use of nitroglycerin after their porosity was lowered by the high para& content of their oil. Success in the use of seismic waves to locate enemy artillery in the First World War led to the use of explosives in the 1920’s for generating ground vibrations to locate geological structures favorable for the entrapment of oil. Explosives also find widespread use in the more conventional applications of well site preparation and pipeline construction. Explosives applications unique to the oil and gas industries include the jet perforating of casings and formations, fighting well fires, and cutting casing during well shut-in.

Jan 1, 1998

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The problem of the maximum depth at which a mine buried in the surf zone or beach zone is a threat to landing vehicles is being studied by Naval Surface Warfare Center (NSWC), Indian Head Division, Naval Research Laboratory (NRL), and The University of Maryland Dynamic Effects Laboratory. The problem was divided into two parts: The first part involves determining how deep a pressure plate mine can be and still detect a vehicle passing over it. This requires determining the distribution of stress within dry and saturated sand when a vehicle passes over a buried mine. The results obtained from that study are presented in a related paper (1). This paper will cover the second part, which entails determining the impulse delivered to the vehicle. This is equivalent to determining the impulse delivered to a plate suspended above the detonating explosive charge and includes an investigation of the distribution of the impulse over the plate. The purpose of the research is to develop a scaling law and/or computational capability which will permit predicting impulse to be expected in the field from tests conducted in the lab. The computational effort is aimed at the development of and confidence in computer codes that can be used to predict stresses and strains in plates due to the detonation of buried mines.

Jan 1, 2004

By Leslie Taylor, W. L. Fourney, Uli Leiste

Over the past few years, our laboratory has been investigating the loading on vehicles due to the detonation of buried explosives. We have been using target plates to represent the bottom of the vehicles that were being subject to the forces from the detonating explosives. Parameters shown to be important in the blast loading were type of soil, stand off distance (distance from the surface of the soil to the bottom of the target plate), and depth of burial (distance of the charge center of gravity to the sand surface). We conducted over the first year of our work a large number of tests which looked at the impulse being applied to the plates as a function of depth of burial, stand off distance, and type of soil. Of the three parameters we found stand off distance to be most important, depth of burial to be the next most important parameter, with type of soil least important. We also found that impulse could be scaled with explosive size quite accurately and that results (for impulse) were quite repeatable from one test to the next.

Jan 1, 2008

By Alastair Torrance, Braden T. Lusk, MinGi Seo, Gary Cavanough

Velocity of Detonation (VOD) is the most commonly used method to determine explosive performance as VOD is a function of the confinement (ground conditions) density and composition of the explosive. Techniques used to measure VOD include resistance wire, time domain reflectometry, simple start stop and fibre optic methods. All these approaches require a cable of some sort to be inserted into each blast hole being monitored and the holes to be fired in a specific sequence. It is time consuming and fairly technical to position the cables correctly to gather the data from each hole. It slows down the hole loading process and increases the number of people on a bench at that time. The equipment and cable limits the measurements to a few holes, typically 5 or less, that are in close proximity. These measurements can generate useful information about the monitored holes but does not provide a full picture of how the explosive is performing across the whole blast and whether any change in performance is noted with changing ground conditions or confinement.

Jan 1, 2019

By Tyler Ross, John Tatom, Lon Lantis

The Institute of Makers of Explosives (IME) began development of a Quantitative Risk Assessment (QRA) tool, IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk), in 2005 as a technology transfer effort with the United States Department of Defense (US DoD). Version 2.0 of the software has been developed over the last two years and introduces many new features and upgrades. Key upgrades include a new map-based user interface, new debris density hazard models, a metric version, and additional user options referred to as “conservatism switches”.

Jan 1, 2014

By J R. Hearst, T R. Butkovich

Explosive-induced fracturing and permeability enhancement far from a free face were studied. A one-dimensional computer program, SOC, was used to predict the total failure-associated distortional strain, ef. Laboratory and field experiments associated the calculated ef with the observed fracture and permeability enhancement. An ef value of 0.015 corresponded to the observed radius of effect, which was about seven times the cavity radius and was consistent with predictions from SOC and from the literature.

Jan 1, 1976

By Stuart Brashear, Robert Brush, Ben Cook

In early 1993, the Piney River quarry owned and operated by the Blue Ridge Stone Corporation of W.W. Boxley, received a series of complaints from the owners of a 130 year-old historic farmhouse that had been converted into a bed and breakfast establishment. Since the distance from the quarry to the farmhouse was substantial, a unique method of seismic data acquisition was utilized to determine if perceived blast effects were caused by air blast or low amplitude, low frequency ground vibration.

Jan 1, 1995

By Andrea Francioso, Roberto Folchi

In order to comply with the latest European Highway Standards, the highway Salerno - Reggio Calabria, in southern Italy, had do be widened and upgraded to reduce its vulnerability to earthquakes. Reinforced concrete viaducts, no longer needed for the new road, had to be demolished. Many bridges still to be used for the highway required refurbishment due to 50 years of wind, frost and salt corrosion. This re-furbishment and new construction had to be carried out simultaneously. To keep the highway open dur-ing the renewal process, all traffic was directed to one side of the road. Demolition was conducted ex-tremely close to operational roadways and viaducts, as close as only 2 cm (0.8 in). Care had to be taken to ensure that the stresses (vibration levels), resulting from the demolished pylons and decks hitting the ground, were below the no-damage thresholds for the nearby acceptors (structures receiving the vibra-tion stresses). These structures included bridges, houses and buried pipelines (water, oil and gas). In some cases, care also had to be taken to preserve the existing pylons supporting decks that were being demolished; since the same pylons were going to be used for the new viaducts (bridges). New continu-ous decks in weathering steel replaced the old reinforced concrete decks.

Jan 1, 2013

By Henry P. Jr Van Ormer

During any blast hole operation the first choice to be made is hole size - it seems simple, just calculate all the factors, spacing, burden, depth, rock characteristics, powder factor, etc. and you have it - Hole Size. But we all know that it is not that easy - the "hole size" is part of a system and many other situations can have great impact on the optimum production Blast Hole Size - such as crusher characteristics, hauling capability, mucking capability and - Drilling Capability!

Jan 1, 1983

By P D. Katsabanis, K Steeves, D Dombrowski

Accurate electronic detonators with firing time accuracy within 100 microseconds of the nominal have been used to control blast results in terms of fragmentation, vibrations and wall control. Axisymmetric experiments and experiments utilizing small benches have been conducted in order to calibrate a numerical model under development and examine the influence of delay interval on wall control, fragmentation and vibrations. The results obtained so far indicate definite advantages of precise timing in reducing back break and wall damage. Fragmentation is affected by the delay interval and high speed film observations and measurements indicate that the delay interval should allow the damage zone from each blasthole to be fully established prior to the detonation of the next borehole. Studies on vibration control demonstrated that vibration synthesis work using signature shots can only be of use if accurate delays are employed.

Jan 1, 1995

By Ralph E. Burnham, J. Kelly Ratliff

"The words “dynamite,” “TNT,” “explosives,” and “blasting” typically cause the general public, andjurors, apprehension and fear. Although blasting operations conducted by well-trained, skilled, andexperienced blasters rarely cause damage or injury, the public’s perception of blasting is that it isdangerous, disruptive, and results in damage to nearby properties. As a result, blasting operations have always resulted in complaints, claims, and lawsuits. However, in recent years, the public perception combined with an increase in public opposition, social media, more stringent regulations, predatory plaintiffs’ attorneys, and the application of strict liability to blasting claims has resulted in an increased threat of litigation to blasting companies and individual blasters. Consequently, many blasting companies find themselves receiving more complaints, involved in more litigation, and facing an alarming number of frivolous claims, which can result in increased insurance costs and other financial tolls. Accordingly, today’s blasting companies must be prepared for litigation and take steps to eliminate accidents and claims before the first shot is detonated on a job. The best way to accomplish this is standard operating procedures that incorporate best management practices, industry standards, and regulations in daily operations. This paper outlines some of the considerations that a blasting company should incorporate into its standard operating procedures before, during, and after the shot."

Jan 1, 2016

By Christian Dye

"The following paper focuses on the developing relationship between the members of theInternational Society of Explosive Engineers (ISEE), and the mining students from the BritishColumbia Institute of Technology (BCIT). During the past two years mining students and theISEE members have worked closely in developing a student chapter within the society and onFebruary 1st 2015, the first Canadian Student Chapter was recognized at the annual generalmeeting in New Orleans. This paper discusses the benefits that both the industry and studentsgain with a strong relationship. The mining students recognize the importance for filling the rolesof retiring members of the society and industry. Prior to 2015 the school had only offered a twoyear diploma program in mining and mineral exploration methods. That included a brief sectionin the use of explosives in the mining industry. In September of 2015 students were recruited forthe first ever Bachelors in Mining and Mineral Resource Engineering program. This engineeringdegree includes a full four month course in advanced blasting and rock fragmentation. Studentssuccessfully completing the diploma program will have an entry level of technical understandingin how blasting is conducted. The students successfully completing the bachelor degree will havean in depth technical understanding of explosives and rock fragmentation. Having this uniqueand dynamic multi-level program provides the explosives industry with a pool of talent that canbe used to fill positions with graduates for all levels of the blasting industry."

Jan 1, 2016

By Miquel Lamadrid, Changshow Sun, Chris Johnson

To reduce blasting overbreak and improve stope stability, several new blast designs were proposed for current and future stopes. Based on the analysis of the powder factor, and the extent of damage zone, the appropriate new blast design was selected. Excellent results were achieved from the new blast design. Comparing the new blast design with the old one, the largest of the overbreaks decreased more tan two times and average overbreak reduced more than two times. The new blast design is currently applied in all mining zones in Leeville underground mine.

Jan 1, 2008

By AJ Rorke

Blasting trials using Daveytronic Electronic Delay Detonator systems (EDD’s) were conducted at the Alpha Ferro Quany (Pretoria) and the Eikeboom Colliery near Witbank in November 1999. The objectives of the trials were to determine the influence of accurate hole firing on rock fragmentation, blast-induced vibration and blast throw. This paper provides an outline of the trials and an analysis of the results. The results were compared with a normal shock tube initiation system. Fragmentation was measured using video-imaging techniques at the hard rock Ferro Quarry for one conventional shock tube blast and two EDD blasts. No significant difference was measured in the fragmentation between the shock tube blast and the two electronic detonator blasts. Joint planes mostly defme the fragments at Ferro Quarry. The fragment sizing was therefore controlled mainly by the rock structure and the blast timing appeared to have no influence. Vibration measurements made at Ferro Quarry indicate that electronic detonators have a marked effect on vibration frequencies compared to shock tube systems. The more accurate detonators resulted in a narrower f+equency band at lower amplitude with similar timing. By modifying the blast timing, the dominant frequencies were changed. The electronic detonators had a significant positive influence, therefore on blast vibration and its control. The timing scatter measured from the shock tube blast was considerable, with measured inhole detonator scatter at 48 ms over a sample of 19 units. Surface delay periods less than 42 ms would therefore not be able to provide effective sequential firing. The scatter of the Daveytronic units was below the 2 ms resolution of the high-speed camera used to film the blasts. Reliable sequential firing, even at very short delay intervals was considered the main reason for notable improved throw in an overburden blast at Eikeboom Colliery. Blast throw was improved by 25% for the test blast.

Jan 1, 2000

By Joshua Micah Hoffman, Lifeng Li, Jhon Silva-Castro

Since millisecond detonators were first introduced, at least two variables among others have been more closely considered when timing a mining blast; the accuracy and the precision of the initiation system. Unfortunately, those variables are often ignored when designing timing for mining blast. Despite the lack of consideration of the characteristics of the initiation system, in some situations, e.g., firing a blast hole with one deck and two detonators, changes in the blasting sequence can be the results of the overlapping between blasting charges. The consequences of such overlapping involve flyrock events, fragmentation and diggability problems, and other difficulties affecting the operation of the mine.

Jan 1, 2015

By Joshua Hoffman, Braden Lusk, Kyle Perry

Despite its porous and lightweight characteristics, aluminum mesh is believed to have blast mitigation properties. The current use of the mesh includes fuel tanks for airplanes, boats, and fuel stations as well as light armored vehicles for the military. The mesh acts as an explosion suppressant by preventing fuel tanks from exploding when exposed to an ignition source. More recently, work has been performed to assess the ability of the mesh to mitigate blast pressures produced by high explosives.

Jan 1, 2009