Search Documents

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Scott Crabtree, Randy Wheeler

Theoretical description of destructive wave interference and the use of sacrifi cial holes is included and is supported by data collected at Springfi eld Underground. Finally, the process by which the reduction in vibration was achieved in practice is described. Results are discussed for several production blasts taking place over a one year period.

Jan 1, 2008

By J. Baird

The Sappington Bridge, a steel arch span bridge constructed in 1904 over the Meramec River, was demolished due to its advanced state of deterioration. The demolition was a project to benefit Crawford County, Missouri, the U.S. Army, the Missouri Department of Transportation, and the University of Missouri – Rolla (UMR) was conducted jointly by the UMR Rock Mechanics and Explosives Research Center (RMERC) and the UMR Center for Infrastructure Engineering Studies (CIES). By arrangement with Crawford County, a 55-foot span of the old bridge was brought to the University Structures Laboratory in Rolla, while the longer, 200-foot span of the bridge was demolished using preburning and explosives. Originally, the longer span was to be blown up by C Company of the 5th Engineer Battalion (from Ft. Leonard Wood, Missouri) under the supervision of personnel from UMR. Unfortunately, permission for the operation from the Department of the Army could not be obtained in time to meet permitting requirements for the demolition. Therefore, a commercial demolition contractor was employed to perform the demolition, and to remove the scrap.

Jan 1, 2003

By William D. Hissem

For those blasthole applications which require the use of holes ranging from 1” to 5.5” in diameter, the use of top hammer drills has been the equipment of choice for several generations of drillers. Pneumatic compressed air and hydraulic compressed oil systems represent the primary technologies which are available to the drilling practitioner. While both employ the same operating principals, the characteristics of performance, cost, and reliability can be markedly different between technologies and manufacturers.

Jan 1, 1998

By Jarrod Bonsmann, Zachary T. Plitt

"A surge in mine related deaths in Middle Eastern conflicts over the past few years has prompted research into the mitigation of the impact on a blast loaded vehicle. In past military conflicts, it has been observed that blast loading can cause injury to the brain but the exact cause is unknown [1]. The recent rise in deaths due to Improvised Explosive Devices (IEDs) has led to research that has speculated that the high acceleration experienced by soldiers on a blast loaded vehicle leads to Traumatic Brain Injury (TBI) [2]. This research aims to investigate vehicle designs that can reducethe peak acceleration for passengers on board the vehicle, in the event that the vehicle is blast loaded by an IED."

Jan 1, 2016

By Phillip R. Mulligan, Kevin Gantz, Aaron J. Ward, allen shirley, Sean Treadway

Understanding the impulse transferred into a structure by the coupled two-phase loading produced by an explosive charge buried in soil is of interest for various applications. The most common impulse measurement technique involves a buried explosive charge and a steel plate/test structure suspended above the charge. Upon detonation of the charge, the soil and overpressure heave the plate into the air. The plate’s trajectory and velocity provide the necessary information to calculate the total impulse transferred from the charge configuration.

Jan 1, 2016

By Patrick Cahill, Jacob Miller, Nolan Mundwiller, Catherine Johnson

"The Experimental Mine at the Missouri University of Science and Technology is undergoing major developments. The underground workings are being expanded to include a ramp down to a second level which will comprise of larger opening and room sizes to better simulate modern mine layouts. Thisexpansion will enable the Experimental Mine to be utilized for many more generations. In addition, the new 15,000 sq. ft. Kennedy Mine Building is being constructed and will house the mine office,classrooms, and three laboratories to accommodate the mining and explosives engineering programs’ ever-increasing enrollment. With these new developments come an increasing need for safety and awareness in regards to explosives and blasting. This paper will utilize the Institute of ExplosivesMakers Safety Analysis of Risk (IMESAFR) software tool, to assess current magazine compliance withthe increased personnel limits and mine building location. Furthermore, this paper will assess theimplementation of a wireless blast warning system consisting of warning beacons and a centrally located siren which will be integrated with the construction of the Kennedy Mine Building. This warning system will provide the necessary precautions to safely conduct blasting-related experiential learningopportunities and research projects, and will enable facility staff to more efficiently oversee blastingoperations at the Experimental Mine. "

Jan 1, 2017

By Greg Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified geologically sensitive due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the geologically sensitive area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model.

Jan 1, 2018

By Brad Bulow

Blasting is an essentially violent process aimed to disrupt and loosen rock for productive excavation. Some dilution of any ore present is the inevitable result. This makes blasting a dirty word to most geologists, particularly in narrow vein gold mines. A 1% increase in gold recovery may be worth $1 M extra revenue to a large mine.

Jan 1, 2000

By Hector O. Romero, Paulo C. Fernández A, Christian Rees Prado, Claudio C. Gajardo

In open-pit mining, estimating post blasting displacement and spillage accurately is essential to guarantee operational efficiency, ensure alignment with production plans and their associated key performance indicators. The absence of predictive modeling tools on blasting operations results in several critical challenges, including operational reworks due to deviations in material displacement, significant discrepancies between mine and plant (ore grade dilution included), misalignment with the reported production plan, and increased operational costs due to inefficient use of resources. This study, conducted at Los Bronces Mine operated by Angloamerican, Chile, addresses the application of a three-dimensional simulation tool that, through numerical modeling, is capable of predicting post blast rock displacement. The implementation was carried out in a pit phase characterized by blasts near the pit boundaries, with a high risk of material spillage and potential blockage of the only access ramp to the extraction levels. By the integration of key design parameters, such as blast pattern geometry, detonating time, explosive charge distribution and pre and post blast survey, an optimal calibration was achieved and validated in seven blasting events to date, reaching an accuracy greater than 80% in estimating post-blast rock displacement and spillage volumes. Furthermore, this study allowed the evaluation of different pattern alternatives with and without spillage mitigation measures (use of air decks near the free face), obtaining a high correlation and accuracy exceeding 95% in predicting the selected design outcome, supporting optimal design selections. The result highlights the usefulness of the model as a decision-support tool for blasting engineers and short-term planning, by reducing the need for unnecessary operational reworks, improving geological and operational reconciliation, and ensuring the alignment of the extracting plan with production targets. The current average deviation is 15%, with higher deviations observed in blasts with smaller volumes of spill or where the simulated sequence was changed before blasting. The use of this type of three-dimensional numerical modeling represents a significant advancement for blast engineering and the optimization of key performance indicators in open-pit mining operations.

Jan 26, 2026

By Frank Hirthammer

Productivity, customer relations, and effectiveness of work depend to an ever-increasing extent on a functioning logistics system tailored to the needs of the user. Of course, it is not possible to cover and explain all aspects of the logistical requirements of even a small part of an industry, in a single article. The article speaks specifically about the particularities and differences in the logistical requirements in the explosives sector. Starting with questions of safety, handling and quality up to the legal basis, there are special requirements regarding the logistics in the explosives sector. The results of innovative logistics solutions are presented using three examples from daily work practice.

Jan 1, 2019

By Reinhold Schnell, Piers Wendlandt, Nathan Rouse

Drilling and blasting are key components of every hard-rock (i.e.,metal/nonmetal/coal) mining operation. Well-executed and maintained drilling and blasting can have a major positive impact on the overall success of such operations. This case study presents the implementation of a new drill and blast engineer position and systematic improvement of the drill and blast operations at a surface metal mine. The findings of and lessons learned from this case study can be applied toother mine operations to improve safety, production, efficiency, and cost savings. Focus areas for the project included refined communications, operational practices and procedures, planning, designing, and data collection and analysis. This case study showed improved efficiency in communication and planning among the engineers, operations team, and contractor groups over the course of the project. An increased awareness of long-term plans and needs for the drills and blasters reduced or eliminated existing delays. Test blasts that implemented new drill and blast designs and updated operational practices and procedures were tested to streamline the process. Constraints regarding explosive product shipments, geological considerations, and a uniform powder factor provided the basis for new blast designs.

Choosing the correct delay time for many blasting applications is an important and critical blast design parameter for controlling fragmentation, muckpile shape, swell, digability, throw, ground vibration and airblast. BAl and its affiliates have monitored thousands of full scale blasts in a variety of field conditions, spanning over 15 countries, with sophisticated blast monitoring instrumentation. In some blast environments, a small change in the choice of delay times used had a dramatic and pronounced effect on the overall blast results. In other blast environments, large changes in the choice of delays used had absolutely no effect on the final results in terms of specific outputs. In environments which were sensitive to the delay selection, the type of explosive, dynamic response time of the rock mass (TMIN), integrity of the material, burden and rock mass geometry, all played a very important ,role.

Jan 1, 1998

By L C. Taylor, H U. Lesiste

This paper describes a method for estimating the density distribution in the soil cap as a function of distance from its top at the time of impact with the target. It provides an estimate of the density distribution in the soil on the center line of the soil cap at the time of target impact for a single depth of burial of the charge and two heights of target and shows that, for the heights of target and the depth of burial considered, the thickness of the soil cap first increases from the in situ value and then decreases. The distribution of soil density along the centerline of the soil cap changes significantly with distance from its original position. These results can be used for validating hydro-code computations and the soil models used in the computations.

Jan 1, 2011

By David S. Bowling

The ER-300 Series White Recorders were developed to provide on economical, yet invaluable instrument for those who desire permanent recordings of such data OS displacement, vibration, concussion (air borne effect) and velocity information. The precise monitoring of earth displacements and air blast magnitudes aids quarrymen and construction contractors in estimating safe blasting limits when operating in populated areas. A refraction model is available for recording velocities which permit the determination of weathered zone depths as well as the .depths to other subsurface formations. The dual purpose (Refroction- Displacement) systems ore utilized for velocity studies and displacement - oir blast measurements.

Jan 1, 1990

By Stephen Chung, Graham Mustoe, Joe Haid

In an open cast coal mining operation, a 305 m (1000 ft) long by 49 m (160 ft) thick overburden cast blast can produce more than a million cubic yards of broken muck that needs to be removed before the coal recovery process can start. In the Powder River Basin of Wyoming, it is common to see 30 to 40 percent of the overburden cast to a spoil that does not require rehandling with heavy equipment. Therefore, the higher the percent cast, the better the cast blast is rated. However, depending on the shape of the muck profile, there is often 20 to 30 percent of the muck standing in front of the high-wall. This portion of muck would require a number of dozers to push down to the dragline pad level. From the mine operator point of view, it is believed that for a given muck profile, there should be an efficient dozer pushing method such that a dragline pad can be developed in the shortest time. As a tool for analyzing this dynamic problem, a 2-D discrete element model, i-PushTM, has been developed to simulate a dozer pushing operation. This mechanistic model takes into account the dozer blade geometry, the dozer operating procedure (e.g. cut-depth, blade fill distance, forward and reverse speeds at specific slope angles), material density and cohesion. To demonstrate how i-PushTM can be used to help determine the most productive push routine, this paper presents three dozer push methods to compare the effectiveness of pushing at 3:1, 4:1 and 5:1 push angles.

Jan 1, 2006

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt. Under the scope of the study, which has been performed to determine the effects of the artificial discontinuities at different depths and the effects of artificial discontinuities through structural damage risk, three test areas, at the same location and same formation, were considered. Six numbers of artificial discontinuities, each 10 m (32, 81 ft) transverse, were created by using pre-splitting and drilling-blasting technology. The number of sequential artificial discontinuities on each test area is two and they have the same length. The length of artificial discontinuities are; 6,80 m (22,31 ft) at the first test area, 13,60 m (44,62 ft) at the second test area and 17,00 m (55,77 ft) at the third test area respectively. The distance between sequential artificial discontinuities is 8 m (26,25ft) on each test area. Thirty-one shots were executed in order to produce vibration (10 shots on the first test area, 11 shots on the second area, 10 shots on the third test area). One hundred and twenty-three seismic recordings were obtained during the execution of the shots by using 4 seismographs. The closest distance between the shot points and the nearest measuring station is 5,30 m (17,39 ft). During the shots, the rock was cracked and there was no fragmentation and/or fly rock. At the first test area, measured PPV values are between 25,40-127,00 mm/s (1-5 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. At the second test area, measured PPV values are between 76,20-177,80 mm/s (3-7 inch/s) before the first artificial discontinuity and less than 76,20 mm/s (3 inch/s) after the second artificial discontinuity. At the third test area, measured PPV values are between 50,80-279,40 mm/s (2-11 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. Peak reduction rates in Peak Particle Velocity (PPV) values determined by measuring as follows: In the first test area 95,77% (106,00 mm/s to 4,48 mm/s) (4,17 in/s to 0,18 in/s), in the second test area 79,77% (176,00 mm/s to 35,60 mm/s) (6,93 in/s to 1,40 in/s), in the third test area 95,85% (from 205,00 mm/s to 8,55 mm/s) (from 8,07 in/s to 0,34 in/s). The arithmetic mean of the differences of PPV values (decrease rate) is 82,66% in the first test area, 69,37% in the second test area, and 92,03% in the third test area. The highest sound value is 138,50 dB and is defined as “noise”. When the measured parameter values are examined it was determined on the USBM norm graphs that these vibrations carry a risk of structural damage in the region before the first artificial discontinuity. While passing through artificial discontinuities the vibrations progress by losing energy and the vibrations passing through two artificial discontinuities do not carry structural damage risk under current conditions.

By David La Rosa, Matthew Craft, Lee Julian

Rules of thumb are ubiquitous in blasting. Typically presented as ratios, they assist with the initial assumptions of blast design and provide guidance for best practice. Examples include the blast hole diameter as a function of bench height, and stemming length as a function of hole diameter. The most common rules of thumb were developed in mid-20th century and it is important for a blaster to know if the rules of thumb are still reliable.

Feb 6, 2023

By Brian Hawkins, David Bradley, Rachel Gooding, Lucas Rodriguez, Patrick Wilson, Kevin Wegman, Dhruv Mittal

The Department of Homeland Security (DHS) has undertaken a probabilistic risk assessment (PRA) approach to quantifying the infrequent, yet high-impact explosive terrorist attacks on the United States (US) homeland and aiding in mitigating that risk through efforts ranging from intelligence gathering, defense postures, detection architectures, partnering with industry to prevent acquisition, and informed medical response. Based on an evaluation of existing model options, a path to the realization of an exterior explosive model (EEM) that builds upon existing models while meeting runtime requirements, maintains consistency with existing DHS chemical, biological, radiological, and nuclear (CBRN) consequence models, and provides sound estimates of the human health consequences of explosive terrorism attacks in open-air urban and rural environments.

Jan 1, 2018

By Francisco Sena Leite, Pedro Brito, Auã Kiahla, Raquel Carvalhinha, Tomi Kouvonen, Vinicius Miranda

Shockwaves that generate vibration in the surrounding environment of a blast, are one of the most important factors to control drill & blasting works near delicate buildings as well as in sensitive structures (wall control). On top of the damage to the buildings themselves, sensitive equipment such as computers, measurement apparatus and medical devices can be also compromised. The most commonly measured values from vibration are PPV (peak particle velocity), acceleration and displacement. Some devices and techniques have been developed in the last decades to measure the impacts of these vibratory phenomena. This information can be used to predict levels of vibration for future blasts and improve their quality of design using the attenuation law. From traditional studies to modern seismographs, a range of solutions are used for this propose. The main problem of applying this kind of technology is the high cost associated with each measurement device. In order to measure the ground vibration using new technologies while lowering the cost, a device has been developed using a microcontroller and electronic sensors commonly found on the market. This new equipment was tested side by side with traditional seismographs and the results were sent to a server for analysis. After several blasts, the necessary data was generated for the validation of the prototype. Through numerical mathematical processing (Taylor’s approach and numerical derivation) the original data supplied by the accelerometer’s sensors was transformed into velocity and, after the data mining, a statistics residue analysis was applied in order to evaluate if the data from the prototype and from the traditional seismographs were similar. The data from each system was used to estimate the attenuation law and the results are shown in this paper.

By Donna Kliche, Charles Kliche

It has been previously documented that various weather conditions such as wind direction and speed, cloud cover and, especially, temperature inversions can significantly affect the overpressure generated by a blast event (Siskind et al, 1980; Oriard, 1999; Siskind, 2000). The overpressure can be magnified downwind and reduced upwind; a change in the regular profile of temperature with elevation can magnify or focus the sound intensity at some distance from the blast event.

Jan 1, 2011