Search Documents

By Pat McLaughlin, J R. (Dick) Daniels

Current practice in establishing quarries in remote areas with hilly or mountainous terrain tends to the use of airtracs (or similar pioneering units) drilling horizontal holes to establish a face, followed by bench development with light excavating equipment. The authors propose the use of a hybrid coyote blast design that incorporates long-round tunneling techniques. This method would, in effect, use down-the-hole (DTH) drills to advance the drift cut to the final depth, allowing longer and more rapid drift advances, and replace the cross-cut drifts with clusters of DTH holes to achieve the same explosives distribution.

Jan 1, 1995

By Tom Burleson

High-speed photography has proven to be an extremely valuable tool for the evaluation of blasting practices in the Warrior Coal Basin. A research project, coordinated by Nelson Brothers Inc. and The University of Alabama's Mineral Engineering Department, has centered on the use of high-speed photography to study and analyze blast performance. A large number of production shots in this region has been filmed and studied. The data obtained from the films have been used to establish graphical relationships between certain blast parameters and overall shot performance. These relationships will be used to develop a computer model that will estimate cast results from a given burden explosive energy combination. This paper describes the methods and procedures used to develop these relationships. The results of the research are discussed along with plans for continuing the research project.

Jan 1, 1988

By Donald H. Matthews

The usual method of dismantling massive concrete formations with explosives, is to totally demolish the entire concrete structure. If any portion of a concrete structure is required to remain in its original form and retain its structural integrity, the use of explosives is usually forbidden and the portion to be dismantled is demolished by mechanical means, using various techniques and equipment that are tedious and expensive.

Jan 1, 1978

By Vilem Petr

Optimization blast design parameters for rounds used at surface mines, quarries or cast blast has taken on a new importance with the increased the cost of the explosives and electronic detonators. This paper addresses the fundamentals of blast design and optimization explosive energy utilized for fragmentation. This laboratory studies shows that one key variable-the strain energy set up in rock mass by blast vibration – can be used to predict the extent of damage done to the rock strata, the degree of fragmentation of the broken rock, and the velocity of the broken rock. It also shows how the dynamic strength of the rock strata is influence the fragmentation size distribution as well as the blastability.

Jan 1, 2008

By Jeffrey N. Deisher, H Y. Fang, Richard P. Scheller, Robert M. Koerner

The need to adequately quantify cracking in structures in the vicinity of blasting activity becomes more important each year. This urgency comes about through a growing number of complaints and lawsuits between the various parties involved, i.e., operator/owner, government, and complaintant. It is felt that existing rules and regulations (mainly based on peak particle velocity of the soil or rock adjacent to the structure in question) fall short of such quantification and lead to confusion in adequately assessing structural damage.

Jan 1, 1977

By A Lance McAnuff, Robert T. Booren

Construction of a dock facility for the Lake Erie Development Project of Stelco Steel involved underwater blasting in commercial fishing waters near Port Dover, Ontario. The most stringent environmental constraints were imposed and a monitoring program involving water overpressure recordings, using equipment developed specifically for this assignment, correlated with observation of caged fish specimens at various distances from the blast source, was undertaken to determine the effects on fish life and to establish whether a protective air-bubble curtain system should be installed around each blast area.

Jan 1, 1989

By Conny Sjoberg, Finn Ouchterlony, Bjorn Jonsson

This contribution reports an investigation of the blasting damage in the contour of an access ramp to a Swedish underground laboratory for nuclear waste related studies. Near zone vibration measurements were made for 7 rounds and the results converted to a site specific scaling law. A simple engineering correction for the influence of the charge length wee developed and the resulting equations used to predict the damage zone depths of three different drilling and charging patterns.

Jan 1, 1993

By Abraham Lindo

Panama’s current economical growth demands an increase in electric power supply; projected energy supply for 2012 exceeds the demand by as little as 2%. In an effort to comply with the demand, several different hydroelectric projects, promoted by the government, are currently under construction and each of them vary in generating capacity, construction design and complexity.

Jan 1, 2013

By J T. Patterson

The mining, quarrying and construction industries are often blamed for causing damage to residential-type structures when explosives are used. The claim experience for blasting vibration damage has been poor. This coverage is excluded from the Comprehensive General Liability (CGL) policy. To obtain this coverage, the policyholder must meet additional criteria and an additional premium must be paid. The risk management process offers the explosives user a technique for minimizing the risk of complaints and vibration damage claims on his insurance program and his cash flow. Case histories indicate that the vibration damage claims expense may be a lower risk than the risk of interference with production and cash flow. An annotated bibliography on risk management and defense of vibration damage claims is provided.

Jan 1, 1978

By Jerry W. Schweiker

An extensive computer program has been developed which will store and analyze pertinent blast related parameters such as date, time, shot coordinates, charge, delay times, etc. In conjunction with these blast parameters, measured ground vibration information can be stored. In addition to actual seismograph data, predicted ground vibration in terms of velocity (inches/sec) can be generated for selected receiver locations. The magnitude of the blast generated ground vibration is based on scale distance relationships. The program can be used for planning blasts, to satisfy local environmental regulations and for insurance and/or legal purposes.

Jan 1, 1984

By Rodney C. Espley-Jones, John C. B Wilson

South Africa is well known for its shaft sinking exploits, and many of the world's biggest and deepest shafts are to be found there. Blasting practice differs in a number of respects from that followed elsewhere.

Jan 1, 1979

By William H. Snyer, Hank Cox

A high explosive device using Linear Shaped Charge (LSC) (to rapidly cut vent and drain openings in a rail tank car) is described. In the event of damage to a tank car loaded with a pressurized flammable fluid, it may sometimes be necessary to perform controlled on-site vent, drain and burn operations. Existing techniques required refinement to achieve the desired safety and procedural reliability for use in emergency situations.

Jan 1, 1994

By Herve Duplaine, Charles H. Dowding

Calculation of response spectra for blast induced vibrations is necessary to fully understand and in some instances comply with frequency or distance related safe blasting criteria. Fortunately, micro-computer systems costing less than $5000 (such as that described herein) can be programmed to calculate response spectra. This system will calculate response spectra from paper as well as FM tape records. It both digitizes (prepares the record for computer calculation) as well as calculates. Programs for the calculation have been written in BASIC, an easy to understand language used with word processors. In addition to describing the equipment and operation of the micro computer the paper will discuss the process of and rules for digitization, use of the computer for record production and will present a simple physical model for understanding dynamic structural response.

Jan 1, 1984

By Randall M. Wheeler

Many blasting companies are using simulated production ground vibration waveforms to aid them in the control of their vibration effects. The simulations are typically produced by using a seismograph to record a signature waveform from a single hole shot and subsequently applying the various delays to be used in a proposed production design. The ability of this simulation method to give good results usually depends on three primary factors. These are: 1) the homogeneity of the seismic travel path from hole to hole; 2) the consistency of the seismic energy release per unit of explosive from hole to hole; and 3) whether or not the delays fire as planned.

Jan 1, 1991

By John Wright

During June and July 1999 a United States Antarctic Program (USAP) team of three commercial divers and one blaster successMy removed an underwater rock obstruction which interfered with safe docking practices of research vessels that call at Palmer Station - the USAP research facility located on Anvers Island, Palmer Peninsula Area, Antarctica. Ordinarily, such a project might be considered routine. However, certain aspects of the project, particularly those dealing with logistics in a remote corner of the earth, sat3eguards for marine biota, and working underwater in the dark of the austral winter, conspired to make this project interesting. Even more challenging was ensuring the protection of the existing pier - a deeply corroded sheet pile structure backfilled with loose gravel and rock - which lay less than 50 feet away from the target obstruction, not to mention uncertainties at the outset as to the nature of the rock mass forming that obstruction.

Jan 1, 2001

By N Vijay Mohan, K V. Balamukund, G Ananth Ramulu

Jointing of steel rods in reinforced concrete structures needs careful consideration as it renders the structure weak at the joint. The jointing is usually done at sections of structural members, where the bending moment and shear force are least. Jointing is done either by overlapping the rods or welding or by mechanical splicing. A novel method of jointing them is by inserting the two rods in a steel sleeve and cladding it on to the rods by subjecting the sleeve to explosive energy. A rod jointed in this fashion is tested for direct tension and bending when used in a reinforced concrete beam. The test results show that it is an effective method. The advantage is that a number of joints can be made in a single operation.

Jan 1, 1993

By J Foklesi, G Bohus, D Benedek

The breakage process in blasting takes place in space and in time and the latter will determine the degree of fragmentation, shape of the muckpile and the extent of displacement. The shock wave travels at the velocity of sound in the material and it can easily be measured. The cracks' velocity is only 0.38 % of the velocity of sound. The number of cracks at any distance from the explosion cavity, their length and the time of development can be calculated.

Jan 1, 1986

By Roger Lucas, Dale Nies

The McLaughlin Mine is an open-pit disseminated gold mining operation. Homestake Mining Company's approach to solving some of the blasting problems inherent to this type of deposit provide an interesting case history. Geology, although unique and site specific, is overall similar to other mines within the Western United States over-thrust belt and demonstrates an excellent example of the blasting conditions and requirements common to most of these operations.

Jan 1, 1990

By Dale S. Preece

A discrete element computer program, DMC (Distinct Motion Code), has been used for several years to simulate blasting-induced rock motion. Recent enhancements of DMC's capabilities have included addition of an algorithm that couples together rock motion and gas flow. This allows the user to specify a particular explosive which also specifies equation-of-state and other parameters necessary to model explosive gas flow from the blastwell. Rock loading by the flowing gas is calculated automatically. The mechanism for calculating the rock loading is the subject of this paper. The rock motion effects the gas flow calculation by changing the porosity. DMC is currently being used on a SUN SPARCstation 2 computer workstation.

Jan 1, 1993

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986