Search Documents

The Federal Coal Mine Health and Safety Act of 1969 requires that each operator of a coal mine shall take accurate samples of the amount of respirable dust in the mine atmosphere to which each miner is exposed, a measure designed to prevent the development of coal workers' pneumoconiosis. This textbook manual is used in the training of personnel to operate respirable dust sampling devices and to conduct sampling programs. It contains the portions of the act applicable to respirable dust standards, the procedures to be followed to insure compliance with Federal regulations, and descriptions of sampling devices.

Jan 1, 1971

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By Ann G. Kim

Fires that occur in abandoned coal mines, waste banks, and in coal outcrops constitute a serious health, safety, and environmental hazard. Toxic fumes, the deterioration of air quality, and subsidence constitute the greatest hazards from these fires. Although tires on abandoned mined land (AML) occur in every coal-producing state, the severity of the problem varies. Methods to extinguish or control AML fires, including excavation, fire barriers, and sealing, are generally expensive and have a relatively low probability of success This U.S. Bureau of Mines report includes information from a variety of sources, i.e., agencies of the Federal Government, State agencies, research reports, conference proceedings, product information, and technical literature. This information has been collated into a comprehensive discussion of AML fire problems. Data on past fire control projects and on the estimated extent of the current problem have been compiled. Factors affecting the occurrence, propagation, and extinguishment of AML fires are discussed. Conventional fire control methods are described, and their probable effectiveness is evaluated. Information on the hazards of AML fires and safety considerations is included. The status of current technology, recent improvements in fire control methods, and areas of current research are discussed.

Jan 1, 1993

By Michael R. Yenchek

Contacts with energized conductors are a major cause of electrocutions in underground coal mines. Sensitive ground fault interrupters (GFI's) installed on in-mine three-phase ac utilization circuits would probably prevent the majority of these deaths. A sensitive GFI is a protective device that detects and interrupts small deadly ground currents in the milliampere range before those currents can cause ventricular fibrillation in humans. Commercially available three-phase sensitive GFI's have not been specifically designed for application in coal mines. The Bureau of Mines therefore tested three commercial GFI models to determine their worthiness for mine power systems. GFI design and construction, transient immunity, reliability, and time-current characteristics were evaluated in laboratory tests. No commercial device was found suitable for mine use without design modifications. The tests results will serve as a basis for the development of a mineworthy sensitive GFI in ongoing Bureau research.

Jan 1, 1985

By Timothy J. Rohrbacher

This report presents results from an ongoing U.S. Bureau of Mines study defining domestic coal reserves. Examinations of five 7 ½ -minute central Appalachian quadrangles have been completed to date. Only 26.4%, 5.0%, 6.5%, 8.2%, and 4.2% at the coal resources remaining in the Matewan, Boltsfork, and Hoskinston, KY; Vansant, VA; and Beckley, WV quadrangles, respectively, constitute economically recoverable reserves. An evaluation of the coal mining industry's impact on the economy of Pike County, KY, wherein the Matewan quadrangle is located, was also completed in order to provide a basic understanding of the influence of coal mining on the local economy. Results show that coal mining is the only major income producing industry in Pike County, accounting for about 46% of the county's income, and 21% of the total available employment, in the base year 1990. If similar results are found in subsequent investigations, a strong argument can be made that traditional coal producing regions may soon be experiencing resource depletion problems far greater and much sooner than previously thought. This will affect not only the coal industry but, given the obvious dependence of Pike County's economy on its coal mining industry, the entire social and economic infrastructure of large areas.

Jan 1, 1994

By Eugene A. Dolecki

This final report describes the work accomplished under U.S. Bureau of Mines Contract #H0242011 - "Feasibility of Automated Rail Haulage Systems in Underground Coal Mines." The report outlines the base for the development and evaluation of automated rail haulage systems in terms of the service requirements for haulage systems in underground coal mines, and of the performance of existing haulage systems. A generalized automated rail haulage system concept is defined. A safety impact analysis of automating the mainline portion of the underground system indicates a 50% reduction in injuries and fatalities. A cost effectiveness (over the total life cycle) study for the system indicates a cost benefit can be obtained from implementing an automated rail system. The design specifications for the total automated rail haulage system - including subsystems and components -are developed, and the equipment types and general design approaches evaluated, with selections outlined. A detailed conceptual design for a prototype automated system is described. Conclusions and recommendations are presented, and a program plan devised for implementing a proto-type automated rail haulage system demonstration in an operating underground coal mine by 1980.

Jan 1, 1976

By F. J. Perzak

The Bureau of Mines conducted a study to develop a standard fire test for 5-gal containers used for storing combustible fluids in underground coal mines. A standard test method was developed which evaluates the performance of the container in a 4-min tray fire. Bureau investigators used the standard test method to evaluate several types of closed 5-gal plastic and metal cans in outdoor tests. Each can tested contained 1 gal of nonfire-resistant (NFR) hydraulic oil. A container failed the test if it lost its contents in any of seven trials. Contents spilled either as a result of thermal rupture or melting. Fewer than 10 pct of the metal containers failed this criterion, but all the plastic containers failed. The metal container failures were usual-ly due to tipping over during pressure relief, which spilled the NFR oil. Replacing the NFR oil in the container with kerosene resulted in failure of more than 30 pct of the metal containers. The standard tests and preliminary tests showed that plastic containers are not equivalent to metal containers in their ability to contain combustibles such as lubricants and greases in a fire. For solvents and lubricants more volatile than NFR hydraulic oil, approved metal safety containers are recommended.

Jan 1, 1985

By K. K. Kelley

The collection and correlation of thermodynamic data concerning substances of metallurgical interest have constituted one of the major activities of the Pacific Experiment Station of the Bureau of Mines, at Berkeley, Calif., for the past several years. Earlier bulletins (32, 33, 34, 36, 36, 37, 38) s in this series are entitled: (1) Contributions to the Data on Theoretical Metallurgy. I. The Entropies of Inorganic Substances; (2) Contributions to the Data on Theoretical Metallurgy. II. High-Temperature Specific-Heat Equations for Inorganic Substances; (3) Contributions to the Data on Theoretical Metallurgy. III. The Free Energies of Vaporization and Vapor Pressures of In¬ organic Substances; (4) Contributions to the Data on Theoretical Metallurgy. IV. Metal Carbonates--Correlations and Applications of Thermodynamic Properties; (5) Contributions to the Data on Theoretical Metallurgy. V. Heats of Fusion of Inorganic Substances; (6) Contributions to the Data on Theoretical Metallurgy. VI. A Revision of the Entropies of Inorganic Substances-1935; and (7) Contributions to the Data on Theoretical Metallurgy. VII. The Thermodynamic Properties of Sulphur and its Inorganic Compounds. The present paper collects and discusses thermodynamic data relating to metal carbides and nitrides, with the view of obtaining usable heat and free energy of formation relationships. Pertinent data on both classes of substances are difficult to obtain experimentally and consequently are extremely rare; it is therefore necessary in many cases, if equations are to be derived, to introduce certain approximations and assumptions. Lack of adequate means of checking results by utilizing data of different types, such as was done frequently in the bulletins dealing with carbonates and sulphates, are readily apparent to anyone who has made even a cursory examination of the available information. Consequently, some of the relationships derived undoubtedly will be found to be inaccurate when more or better data become available. Nevertheless, in view of the importance of some of these substances, it appears worth while to consider the information available at present and to attempt the formulation of as complete a

Jan 1, 1937

By Edward P. Barrett

The production of sponge iron is one of the earliest arts in the metal¬lurgy of iron and steel. The idea of producing iron direct from ore at temperatures lower than the melting point of, the iron has persisted throughout the centuries. The purpose of this paper is to present a general picture of the methods, proposed or tried within the past 100 years, for producing sponge iron by treating hot ore with heated reducing gases. The abundant literature has been abstracted, and quoted freely. Publications concerning more detailed information on the various methods are referred to in the footnotes and in the bibliography.

Jan 1, 1949

By R. R. Allen

Gieseler plastometer tests were performed on eight western coking coals at retort - immersion depths ranging from 2 to 3-3 /4 inches (measured to the center of the coal charge ) . Increased maximum fluidities were associated with greater retort - immersion depths , the most pronounced increases being observed on highly swelling coals when tested at 3-3 /4 inches . The maximum fluidity of one of these coals when tested at 3-3 /4 inches was 146 percent greater than that observed at 24 inches . Retort - immersion depth had no significant effect on the temperatures of initial softening , fusion , maximum fluidity , end of fusion , and solidification .

Jan 1, 1964

By J. A. HUFF, V. V. BAKER

This circular contains a statement of the statutory provisions of the several States regarding the appointment , qualifications , and remuneration of State mine inspectors . States have been omitted where no specific provision has been made by the State law for mine inspectors .

Jul 1, 1931

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By D. Harrington, W. J. Fene

For nearly 30 years the Bureau of Mines has contended that mine explosions can be prevented and has pointed out to the industry ways and means by which they could be avoided. The record of co2l-mine explosions • during the past fiscal ?Bar bears out the :Bureau1s contention, inasmuch as fewer men were killed by coal-mi~e e:xplosions in the United States during that year than in :gi_y corresponding 12 months in the history of coal mining in the United States, insofar as records are available; and more than a year has elapsed since·a major explosion (in which five or more men were killed) has occurred, this being t.1-J.e first continuous 12- month period without a major coal-mine explosion disaster in the United States in more than 60 years. The methods of preventing mine e:iiplosions are well known to experienced, well-informed persons cngnged in coal mining. Despite this knowledge, many coal-mine operutors continue to use practices and methods that they should know have resulted in countless explosions, and mine workers persist in following past procedure or in breaking safety rules and practices almost certain eventually to result in disaster. ' Virtually all explosions are the result of human failure, such as carelessness or neglect by officials or workers or others. These human failures can be corrected chiefly by ed.ucation and proper and adequate supervision and strict discipline. In some instances mine officials are ·lax, careless, poorl~• informed, and often incompetent; end in many instances miners have repulsed the introduction of known preventive methods because of sheer obstinacy, ignorance, heedlessness, or possibly fear that the operator was trying to o'bta.in some unfair adva.,.'1. tago or would neglect some other phase of accident or e,:plosion prevention. The freedom of the fiscal year 1938-39 from major coal-mine explosions ar..d frora any considera~le number of fat,JJ.i ties from minor explosions is a. matter for congratulation, but on the other hand. the occurrence of one rather bad e~losion in each of tho 3 calendar years 1937

Nov 1, 1939

By S. L. Weber, D. E. Banks

"Silicosis was first reported by the ancient Greeks and is apparently as old as human history. The prevalence of this illness peaked in the last half of the 19th century and the early part of this century, when mechanized industry was developing and the relationship between dust exposure and disease was less well understood. Yet, even today in devel-oped countries, sporadic outbreaks of silicosis occur when workers are consistently exposed to silica particles of respir-able size (0.5 to 5.0 µm in diameter) at levels exceeding those recognized to be safe.Silicon dioxide or silica. is the earth's most abundant mineral. Silica is considered to be either free (i.e.. unbound to other minerals) or combined. Minerals with high amounts of free silica include quartz (including granite) flint. Chert, opal, chalcedony, and diatomite. Combined forms of silica are called silicates and include, among others, asbestos talc and kaolin.In the crystalline form, silica exists as quartz, cristobalite, and tridymite (Fig. 28). Of these quartz is ubiquitous in the environment and occurs as sand and as a part of many rocks. Cristobalite and tridymite occur naturally in lava and can be formed by the heating of quartz or amorphous silica. Cristo-balite is more tibrogenic than quartz. Amorphous silica is noncrystalline and, therefore, is relatively nontoxic and does not cause silicosis. It occurs as diatomite (skeletons of pre-historic marine organisms) or as vitreous silica (glass), the result of carefully melting and then quickly cooling free crystalline silica. Heating diatomite with or without alkali (a process known as calcining), forms cristobalite and adds the respiratory toxicity of free crystalline silica.There are many opportunities for occupational exposure to respirable crystalline free silica. Some of the commonly en-countered occupations in which the risk of silicosis exists are reported in Table 20.Silicosis. the pulmonary disease caused by the inhalation of silica particles of respirable size, is most commonly cate-gorized by findings on the chest radiograph. The most typical presentations simple silicosis and progressive massive fibrosis appear different radiologically but are grouped under the category of classic silicosis because they are a part of the radiographic spectrum of this illness. Radiographically, simple silicosis appears as small (less than 10 mm in diameter), rounded opacities, typically predominant in the upper lung zones. Progressive massive fibrosis is the result of the coalescence of these small nodular opacities and appears as larger opacities (more than 10 mm in diameter), again typicallydistributed in the upper lung zones."

Dec 1, 1995

A computer program for the static load analysis of linear elastic structures is presented. It is the product of a two-year project for the development of a efficient program for the analysis of mine-type structures. The report is divided into two parts. The first part explains the general method of analysis, the computer program organization and the most significant numerical techniques used. The second part is a user manual for the computer program. The FORTRAN IV computer program deck and example problems were transmitted separately to the sponsor. Request for a copy of the program should be directed to the Bureau of Mines, Denver Mining Research Center.

Jan 1, 1972

By Milford L. Skow

This report summarizes the principal activities and results of 15 years of research by the Bureau of Mines, U.S. Department of the Interior, on methane control in coal mines. This research has investigated fundamental factors regarding the occurrence and movement of methane in coal beds, removal of methane prior to mining, and control of methane during mining. The report includes a bibliography listing the more than 150 publications resulting from the Bureau's methane control program as well as numerous other references, a section on methane recovery and use, a look at the upcoming Bureau of Mines research program, and a brief review of methane drainage practices in other coal-producing countries.

Jan 1, 1980

By J. Vance Batty

The Permian Red Bed copper deposits of the South Central States are a potentially important resource. Only the higher grade, near-surface ores are now exploited because conventional froth flotation does not recover oxidized copper minerals which comprise 10 to 15 percent or more of the copper content of typical ore. Laboratory-scale beneficiation studies were initiated to devise a method capable of recovering both sulfide and oxidized copper mineral. Testing established that the high clay and gypsum content of typical ore prevented effective flotation of the oxide mineral using sulfidizing, fatty-acid, or oil emulsion techniques. A modified leach-precipitation-flotation (L-P-F) procedure recovered over 90 percent of the copper, compared to a recovery of 77 percent obtained by conventional sulfide flotation. The higher costs of the L-P-F method would reduce the increased revenue from higher copper recovery. An increase in copper price and/or an increase in oxide copper content of the ore would make the L-P-F process comparatively more attractive.

Jan 1, 1970

By R. F. Waters

Laboratory-scale selective volatilization methods developed by the Bureau of Mines to recover germanium and gallium concentrates from coal fly ash and phosphorus furnace flue dust are summarized. In the better experiments between 85 and 98 percent of the germanium was recovered as the lower oxide and as sulfides, and between 75 and 97 percent of the gallium was recovered as the lower oxide and as the trichloride. Grades of the condensates were inconsistent and varied between a few tenths of a percent and 8 percent, depending on the method used. In the primary extractions of germanium alone the degree of enrichment surpassed 100 to 1, and for gallium the best ratio was 30 to 1. Upgrading of condensates by vaporization retreatment and by leaching and precipitation is discussed. An appreciable degree of mechanical preconcentration by attrition scrubbing and elutriation was possible on two fly ash samples.

Jan 1, 1967

By Noel N. Moebs

This report summarizes a Bureau of Mines study on the use of geotechnology to identify and reduce ground control hazards at slate quarry operations in eastern Pennsylvania. The major ground control hazard is falling rock, attributed to weathered bedding plane faults, which weaken quarry highwalls. It was demonstrated that these faults can be detected outside of the quarry perimeter using surface resistivity measurements. Falls of ice from quarry highwalls constitute a second major hazard, which requires water diversion as a basic control method. In situ stresses seemingly cause only minor problems in slate extraction although they could interact with developed stresses and lead to failure of barriers between quarries. Pull tests showed that rockbolts anchor firmly in slate and should prove effective in securing loose rock.

Jan 1, 1986

By R. B. Anderson

As a part of a Bureau of Mines program on the conversion of coal to liquid and gaseous fuels, the kinetics of the Fischer-Tropsch synthesis on iron catalysts was investigated. Nitrided catalysts were studied at 21.4 atmospheres using feed gases ranging from 2H2+1CO to 0.25H2+1CO, and at 7.8 to 21.4 atmospheres using 1H2+1CO gas. The overall apparent activation energy increased with increasing carbon monoxide content of the feed gas from 19.5 kcal/mole for 2H2+1CO to 23.7 for 0.7H2+1CO. The rate of synthesis with 1H2+1CO feed increased linearly with operating pressure from 7.8 to 21.4 atmospheres. A semifundamental rate equation of the form [r=a'PH2 0.6pco 0.4- ?r0.5PH200.5] was shown to fit the data satisfactorily. The relative usage of hydrogen to carbon monoxide decreased with increasing conversion, passed a minimum, and then increased. Apparently water is the principal primary product and carbon dioxide is produced by subsequent water-gas shift reaction. In another group of experiments water, carbon dioxide, argon, and methane were added to 1H2+1CO feed to a nitrided iron catalyst. Argon and methane were only diluents. Carbon dioxide was a slight inhibitor and water vapor was a strong inhibitor to the rate of synthesis. Water accelerated the water-gas shift and usually increased methane production. Important factors of catalyst geometry in determining rate were found to be particle size and extent of reduction. Apparently the active portion of the catalyst is confined to a layer of 0.01 to 0.02 cm from the external surface of particles. A special solution was made of differential equations relating re¬action at the catalyst surface to diffusion in pores of the catalyst for spherical particles with an active layer surrounding an inert core. The equation derived expressed the experimental data reasonably well. Diffusivities determined by this equation varied from 3 to 24X10-6 cm2/sec; these values are of the same magnitude as observed for the diffusion of gases in liquid. The appendix presents a group of synthesis experiments at pressures of 21.4 to 103 atmospheres. In this range the rate of synthesis on nitrided iron catalysts increased with pressure to the 0.74 to 0.84 power.

Jan 1, 1964