Search Documents

By R. H. Church, William E. Webb, Walter E. Pittman, James R. Boyle

As part of the Bureau of Mines health and safety research program, a short-range locator system, capable of locating miners who have become trapped following a mine accident, has been devised, The system consists of a lightweight, low-power radio transmitter incorporated into a miner's cap lamp battery and a directional receiver carried by rescuers. Prototype transmitters have been constructed, and the propagation of their signals has been investigated, The detectability of the signal in underground coal mines has also been investigated, This research indicates that a short-range location system would serve as an economical and practical means of locating miners from within the mine following an accident,

Jan 1, 1984

By G. H. Bennett

A field experiment was performed in a production unit of an operating copper room and pillar mine to compare the support capabilities provided by resin and mechanical roof bolts. Resin and mechanical roof bolts were alternately installed in eight intersections in a single entry. Rock mechanics instrumentation was installed to measure roof sag, bed separation, convergence, bolt pullout, torque, and strain. Bolt cost and installation time are included. Two analyses of the test were made. The analysis of the rock mechanics data showed there was no definite difference between the two bolting systems. From a broader analysis on a mine-wide basis it was concluded that resin bolts gave better support. A critical view of the experiment is given in the appendix.

Jan 1, 1974

By E. M. Tignor

A research program to aid development of improved methods for increased production of petroleum from partly depleted reservoirs is a vital part of the Bureau of Mines effort to effect true conservation of that mineral resource. This report presents results of an investigation to identify the clay minerals within some Appalachian petroleum-reservoir sands, the effect of clay content on the fluid-flow behavior of those sands, and the use of brines in water-flooding operations. Permeability measurements using kerosine, calcium chloride brine, simulated oilfield brine, potassium chloride brine, sodium chloride brine, and distilled water were made on reservoir-rock cores. Clay fractions were separated from sand grains of disaggregated portions of each core sample, and the clay minerals were identified by the differential thermal analysis method. Relations of the permeability to various fluids were developed.

Jan 1, 1957

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system or systems, thus disclosed. Of the several systems initially investigated and evaluated, four Showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system, or systems, thus disclosed. Of the several systems initially investigated and evaluated, four showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By John W. Thatcher

A demountable X-ray tube vacuum spectrograph was designed by the Bureau of Mines for the determination of long-wavelength X-ray spectra from the light elements. This instrument was operated for both secondary and combined primary-secondary excitation of the aluminum K-series. There was an increased analytical sensitivity for elements in period 3, and an indication that with improved X-ray tubes or direct election excitation of the sample, X-ray determination of elements in period 2 is also possible.

Jan 1, 1965

By Norman G. Foster

The mass spectra of 14 previously unreported alkylthiophenes are pre-sented. Low ionization voltage data of selected compounds from these 14 and 23 previously reported alkylthiophenes are presented and discussed for their value in supporting fragmentation mechanisms analytical correlations. A comparison with and corroboration of earlier correlations is made. Additional correlations concerning detection of side chain branching and the detection of ethyl-alkyl and propyl-alkylthiophenes are made. A discussion of the possible fragmentation routes and mechanism of fragmentation is given. Speculative structures are inferred s out some of the ions and hence this work provides a basis for suggesting fation mechanisms for the alkylthiophenes according to modern theories ass spectrometry. Verification of these mechanisms must await the availability of isotopically labeled molecules which are labeled in specific lotions that permit the definition of the paths of frag-mentation. Some suggestions for further work to generalize on the correlations and studies made to this point are presented.

Jan 1, 1965

By L. R. Fisher

The purpose of this investigation was twofold: (1) To devise a rapid method for determining quantitatively the porphyrin-carboxylic acid content of a particular crude-oil porphyrin aggregate, and (2) to isolate porphyrins in the crystalline state from crude-oil porphyrin aggregates. The first purpose was accomplished by applying adsorption chromatography. In fulfillment of the second aim three different crystalline porphyries were isolated by methods which involved both adsorption chromatography and fractionation of benzene solutions with hydrochloric acid of varying strength. The three porphyrins had etio, rhodo-, and phyllo-type absorption spectra, respectively. INTRODUCTION Many samples of petroleum have, as interesting minor constituents, chemical compounds known as metalloporphyrins. Their presence in crude oil and other bituminous materials was first discovered by Treibs a quarter century ago. Much experimental work has been done on metalloporphyrins because of their importance to the petroleum industry. They have a deleterious effect on refining catalysts. The ash resulting from the burning of heavy fuel oil is very reactive, We to the presence of metallic constituents, particularly vanadium. In oil-fired gas turbines, the ash may build up on the blades, causing imbalance of the rotors and, in addition, severe corrosion. In industrial boilers, the ash residue is responsible for severe damage to boiler tubes and to the refractory brickwork (15).4 Through study of the chemical constitution of the various metalloporphyrins found in petroleum, much can be learned concerning the origin, migration, and history of crude oils.

Jan 1, 1961

By Scott Turner

Within recent years , people have begun to realize the importance and significance of the mining and allied industries . The leading part the engineer plays in civilization is becoming recognized . However , accurate quantitative knowledge of the industrial importance of mining is still seldom possessed except by those close to this business . It is true that there are a few who go to the extreme and represent the whole progress of civilization as a reflection of man's gradual mastery of mineral utilization , but on the whole , the magnitude of the industry is underestimated . The uncertainties of mining , as evidenced by the variable results of prospecting on surface or underground , in an unknown new field or from the bottom levels of a mature mine , the ins and outs of tonnages and metal contents , the possibility of a widespread or even a sudden change between cost and realization-price , add to its picturesqueness and make mining attractive to some . To many , the fact that results are generally more uncertain and less predictable than in other industries lends added charm . The following pages may serve to call attention briefly to the importance of mining relative to other industries in the United States , in Canada , and in the world . Ordinarily , the annual primary mineral production of the United States amounts to about 5 billion dollars . The average for the last five years has been a little over 5 billion dollars . Last year , sadly enough , it was less than 34 billions . Just now , we are on the decline , and have been for the past two years . In Canada , the 5-year average was about 268 million dollars . Last year it was 227 million . Due in part to gold output ( in 1930 , for the first time , Canada's gold production exceeded that of the United States ) , the Canadian average is holding up better than ours . It has been estimated that the average world mineral production over the past five years has amounted to about 12 billion dollars , while in 1931 it was less than 8 billions . The mineral industries are as indispensable for the conduct of modern society as are those of agriculture , but , in the United States at least , they receive far less recognition from the Government . With us , agriculture is fostered by a great department that is maintained by enormous appropriations , while the mineral industries get but little financial support . In the United States , in the calendar year 1930 , the value of production by these two industries were as follows : to 1 . Agriculture ( inclusive of forestry ) 9.9 billion dollars ; mining 4.8 billions ; ratio 2 Direct appropriations by our Federal Government were 109 million dollars to agriculture and 2.8 million to mining , a ratio of 39 to 1. Obviously this is out of balance to the extent of 19 to 1 in favor of agriculture .

Jun 1, 1932

By Martin H. Stanczyk

The direct dissolution of a typical zinc sulfide flotation concentrate by elevated temperature and pressure leaching was investigated. The concentrate assayed about 55 percent Zn, 32 percent S, 6 percent Fe, and 1 percent Pb and contained minor quantities of copper and precious metals. The influence of various factors on the dissolution of the zinc in acidic and ammoniacal pulps when using oxygen as the oxidant was determined. The tests revealed that the sphalerite was difficult to oxidize. Complete dissolution of the mineral required vigorous and intimate nixing of the gaseous, liquid, and sold phases. The addition of pyrite or sulfuric acid to water slurries of the concentrate was required to obtain a high zinc extraction when leaching under acidic conditions. The quantity of pyrite and acid used was about 0.125 and 0.25 pound, respectively, per pound of zinc sulfide contained in the leach charge. In tests with acid, about 96 percent of the zinc was extracted from the concentrate in 1 hour at 200° C. when the oxygen partial pressure was 75 pounds per square inch gage or higher. Leaching with a continuous flow of air as the oxidant gave results that were almost as good as those obtained when oxygen was used, In tests with air fed through the autoclave at 320 liters per hour, 95 percent of the zinc was dissolved in 1 hour, Acid leach solutions assaying approximately 58 grams Zn per liter and containing Fe, Ni, Cr, and Cu impurities were produced in the better tests. The leached residue consisted essentially of red iron oxide together with substantially all of the lead and precious metals.

Jan 1, 1961

By C. G. Kirkland

An apparatus for determining trace impurities in Grade-A helium by mass spectrometer methods was designed and built by the Federal Bureau of Mines. Grade-A is the designation for helium commercially produced by the Bureau. Its nominal purity is 99.995 percent. The device, following a suggestion by Deaton, concentrates the impurities in the helium by freezing them out in a coil-and-trap assembly cooled by liquid helium. A known volume of helium is passed through the trap, the concentration ratio determined, and samples of the concentrated impurities are analyzed by mass spectrometer methods. The apparatus has been in service for approximately 20 months and has satisfactorily met all requirements. Over 200 analyses were made of helium contained in conventional cylinders, obtained from the Amarillo, Exell, Otis, and Navajo Helium Plants, during the 6-month period ending March I, 1959. Total impurity concentrations, in parts per million, were as follows: Amarillo, 19.1; Exell, 17.1; Otis, 11.3; and Navajo, 6.6. Neon and nitrogen were the major impurities. Complete data are shown in table 4 in the body of this report.

Jan 1, 1960

By W. J. Boone

Experimental determinations were made of vapor-liquid equilibria data for a helium-nitrogen-methane system. A mixture composition was chosen to approximate the crude helium to be produced Or conservation that will eventually be further refined to obtain pure helium. Although there are publications of studies of the vapor-liquid equilibria of helium-nitrogen, helium-methane, and nitrogen-methane binary systems, there is little indication of work done on the ternary system of helium-nitrogen-methane. The experimental data presented in this report supplement the information available for the binary systems. The equilibrium vapor-liquid data and equilibrium vaporization coefficients are presented in tabular form. Graphs are employed to show an extensive amount of the data.

Jan 1, 1963

By D. E. Sullivan

The Bureau of Mines investigated the availability of potash from 68 mines and deposits in 12 market economy countries (MEC's) containing, at the demonstrated resource level, approximately 11.7 billion metric tons (mt) of potash in assay terms of contained K2O; K2O as used by industry as a standard of comparison for the different forms of potash. These resources include almost 190 million mt in the United States, 9.63 billion mt in Canada, approximately 430 million mt in Western Europe (France, Federal Republic of Germany, Italy, Spain, and the United Kingdom), 1.24 billion mt in the Middle East (Israel and Jordan) and over 220 million mt in other countries (Brazil, Chile, and the Congo). This analysis his determined that future production of potash in MEC?s will most likely continue to be from the large resources associated with producing operations in Canada. Based solely on the demonstrated resources included in this study, potash mining in the United States would decline while overseas production from MEC's can continue into the next century at near current production levels. However, timely development of new or inferred resources would offset any such decline. Producing mines in Canada have the resources to increase and maintain increased production well into the next century. For U.S. potash users, Canada is a long-term stable and secure source.

Jan 1, 1986

By R. B. Anderson

SULFUR poisoning of iron catalysts in the Fischer-Tropsch synthesis was investigated at the Bureau of Mines, because synthesis gas produced from coal contains sulfur compounds. Tests of two typical iron catalysts with synthesis gas containing known concentrations of H2S were made to determine catalyst life as a function of sulfur concentration to ascertain the type of gas purification required. Fixed beds of activated steel turnings and a fused iron oxide catalyst were investigated in sulfur poisoning tests at 21.4 atmospheres with IH2+100 gas containing 6.9, 23, or 69 mg S as H2S per cubic meter (0.3, 1.0, and 3.0 gr per 100 cu. ft.). In tests of reduced catalysts at constant temperatures, more than 80 percent of the activity was lost when 0.5 mg S/g Fe was introduced. Poisoning of nitrided or carbided fused iron oxide catalysts to a given extent required more than twice as much sulfur than for the corresponding reduced catalyst. When the synthesis temperature was increased to compensate for loss in activity, tests of the fused iron oxide catalysts at constant productivity could be continued for 19 to 98 days. The tests were terminated by clogging of the reactor, presumably caused by carbon deposition. One objective of the present work was to determine if synthesis gas, purified by the Bureau of Mines' hot-potassium carbonate process for removing H2S, OOS, and CO2, is suitable for synthesis on iron catalysts. The sulfur content of the gas purified by tills process is in the range of concentrations used in the present work. In constant-productivity tests of nitrided fused iron oxide catalysts with synthesis gas containing 6.9 mg S/m3, catalyst lives are nearly long enough for serious consideration of tills mode of operation. However, factors relating to selectivity and stability of the catalyst indicate that this type of operation is impractical for a commercial process. On this basis additional gas purification, such as iron oxide boxes following a hot potassium carbonate scrubber, is desirable.

Jan 1, 1965

By David E. Siskind

The Bureau of Mines has studied the fracturing and associated damage occurring in the vicinity of blastholes from five shots fired in the shale pillars in the White Pine copper mine, White Pine, Mich. Four types of explosives (AN-FO, commercial extra dynamite, ammonia gelatin dynamite, and a low-density, low-velocity permissible) were used. Cores were taken from the blast region and examined by ultrasonic and petrographic techniques. Pulse wave velocities were measured across the core diameters, and thin sections showing cracks and changes in lithology were examined in an attempt to establish zones of damage. Cores from the blast regions and areas near pillar free faces were found to have abnormally low pulse velocities. Petrographic study of the thin sections showed that the negative velocity anomalies were caused by cracks in the cores. Crushing and extensive fracturing prevented meaningful measurements on core fragments from the immediate blast vicinities. Compositional, changes and other rock nonuniformities, such as joints and preexisting fractures, tended to mask detailed damage differences among the four explosives; however, the two most energetic explosives (extra dynamite and ammonia gelatin dynamite) produced damage zones two to three times as large as the AN-FO and low-velocity permissible explosives.

Jan 1, 1973

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966

By E. D. Eastman

There are three researches upon the specific heat of water vapor by the method of explosion that are sufficiently advanced in technique and suitable in plan to justify careful study of their results , with the double purpose of fixing the best available experimental values and indicating the attainable accuracy of the method. These three researches comprise the work of Pier , Bjerrum , and Siegel.5 The work of earlier date than Pier's suffers from obvious inaccuracy of measurement , while the experiments more recent than Siegel's , such as those of Womersley6 , of Bone and his collaborators , and of Maxwell and Wheeler , 8 are for the most part not well designed for the accurate determination of the heat capacities in question . Some of the errors to which they are especially subject have been discussed by David and by David and Thorp.

Sep 1, 1930

By A. F. Colombo

The western Mesabi range nonmagnetic taconites containing about 34 percent Fe were evaluated by the Bureau of Mines in a 900-pound-per-hour pilot plant employing a selective flocculation-desliming-cationic flotation technique. The flotation step was a reverse flotation process and involved the flotation of the gangue minerals. The objective of the research was to increase the availability of domestic raw materials for the iron and steel industry. The beneficiated ores yielded concentrates containing 62 to 64 percent Fe and less than 5.5 percent Si02 with accompanying iron recoveries that averaged about 75 percent. Comparable flotation results were obtained with either fresh or 80 to 90 percent reclaimed water. Recycled waters having turbidities as high as 5,000 ppm Si02 did not affect the flotation process. Reclaimed waters containing residual calcium contents of less than 10 ppm gave better flotation concentrates than those containing 15 ppm.

Jan 1, 1976

By Lucien Eaton

The mining methods described in this paper are those used in a large mine producing hard specular ore on the Marquette Range in the Upper Peninsula of Michigan. Although the conditions of mining are unique in this district, they are similar to those in many other districts, and information in regard to the methods used and the results obtained should be of interest. The methods now used are an outgrowth of those of former years which have been adapted to conform with improvements in mechanical appliances, changes in the wage scale and labor supply, and the' selling price of the product. The mine is situated' at Ishpeming, in the Upper Peninsula of Michigan, 16 miles west of Marquette, its shipping port on Lake Superior.

Jan 1, 1929

By Mark S. Sanders

Based on laboratory tests and preliminary field tests of off-the-shelf steel toed rubber boots, a molded sole design was developed to provide increased traction over conventional calendared sole miners' boots. The pattern provided sharp edges perpendicular to both lateral and fore-aft slip vectors. The sole was designed to reduce mud caking. An instep lace-up capability was added to better secure the foot inside the boot. A five month field evaluation compared the prototype boots to the boots the participants usually wear. Although objective slip and fall data showed no significant advantage for the prototype, subjective evaluations made by the participants indicated increased traction for the prototype boots. Approximately 75 percent preferred the prototype to their own boot. Approximately one-third used the lace-up capability. It was concluded that molded soles provide better traction than calendared soles for the underground mining environment.

Jan 1, 1982