Search Documents

By A. H. Roberson, F. S. Wartman

For many years , it has been the common practice at most copper mines to recover copper in solution in effluent mine water by precipitating the copper with scrap iron.4/ The technique employed varies from simply throwing scrap iron or tin cans into the waste ditches to passing the water through elaborate launder systems containing detinned scrap and baled cans . In general , a considerable amount of low - cost copper has been recovered that otherwise would have been lost . Iron consumption usually varies from 1 to 1-1/2 pounds of iron for each pound of copper recovered . The grade of the precipitate may be as much as 90 percent copper.4/ ,5/ Where the consumption of iron is materially greater , its cost is likely to be the determining factor of profit . In times of emergency, when the demand for scrap iron for remelting increases the cost of the iron sharply, and the supply of tin cans is not large enough to meet requirements , recovery of the copper might not be economical . The three principal reactions that take place when an acid mine water containing iron and copper salts in solution is brought into contact with metallic iron are : (1 ) Copper is precipitated and an equivalent amount of iron is dissolved , CuSO4 + Fe Cu + FeSO4 ; ( 2) ferric salts are reduced to ferrous salts , Fe2 (SO4 ) 3 + Fe = 3FeSO4 ; and (3) the free acid in the solution reacts. with metallic iron to produce ferrous sulfate , H2SO4 + Fe = H2 + FeSO4 . = Because of the reported high.consumption of iron (5 to 6 pounds per pound of copper precipitated ), when copper in water from the Hornet mine of the Mountain Copper Co. ( California ) was precipitated upon scrap iron , a series of tests was made to determine . the . optimum treatment, time , and consumption of iron .

Feb 1, 1944

By Aner W. Erickson

"Preliminary examination of tungsten deposits on the Mountain View property near Hyder, Alaska, was made by Neal M. Muir, an engineer of the Bureau of Mines daring the summer of 1942. Fifteen samples were cut, rough esti¬mates of ore reserves were made, and it was proposed to extend the drift on scheelite-bearing vein 300 feet in a northwesterly direction.From May 22 to October 24, 1944, an exploratory project was conducted on the property by the Bureau. In the course of this work, the camp buildings were rehabilitated; the dam, hydraulic line, and machinery were repaired; 226 feet of drift was driven; 80 groove samples aggregating 3.9 tons in weight were cut; a 6,000-foot surface and underground traverse was run; and the area was mapped in detail.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is doe Neal W. Muir, project engineer, and Robert S. Sanford, acting chief, Alaska Division, Mining Branch, for their supervision of the field work and revision of the report.Acknowledgment is also made to Silbak Premier, Ltd., for rendering valuable assistance in the repair of equipment and for extending various courtesies to Bureau of Mines personnel during the conduct of this project.The Mountain View property is located at latitude 55° 59' north, and longitude 130° 03' west in the Salmon River mining district of southeastern Alaska, about 5 miles in a northwesterly direction from the town of Hyder, which lies at the head of Portland Canal, as shown in figures 1 and 2. Vein outcrops and surface workings are at an elevation of 950 feet and occupy the west flank of a low ridge between Skookum and Fish Creeks, as shown in figure 3. The portal of the long adit exposing the vein at depth is on Skookum Creek about 550 feet north of the confluence of Skookum and Fish Creeks.Access to the property is over a 4-foot wide trail built and maintained by the United States Forest Service. This trail is suitable for pack animals and is adequate for transportation of supplies and material for exploratory work. During the periods of camp construction and past exploratory operations a 4,000-foot, single-cable, aerial tramway, now in disrepair, served for transportation of materials and all machinery from the Salmon River Highway to the property. The cost of such hauling was high, amounting to $12 a ton. Topography is suitable for construction of a ""cat road"" 2 miles in length, connecting the property with the Salmon River Highway. It is estimated that such a road could be built for $5,000 a mile, and supplies, machinery, and concentrates could be haled over it at a cost of less than $2.50 a ton."

Sep 1, 1946

By F. W. Hoertel

Tungsten from the hydrogen reduction of WF was vapor - deposited to coat MERM (Material Evaluation Rocket Motor ) graphite and rhenium- lined graphite nozzles . These nozzles have surface configurations that preclude the conventional fabrication of high- density- tungsten liners . Operation at 550 ° C produced selectively placed uniform coatings of specified thicknesses at near theoretical density . An acceptable coating could not be deposited on a beryllia nozzle because of an undesirable side reaction between the substrate and one or more of the products of the reduction reaction .

Jan 1, 1964

By Russell R. Trengove

Core samples from an ore horizon 2,000 feet below the surface were successfully obtained by rotary drilling at the property of the Eureka Corp., Eureka, Nev. The ore was soft and friable; cores were not obtained previously with diamond drills. Whipstocking was used to get samples in a zone 200 feet from a vertical hole. A technique in shipstocking, by which the direction and deviation of the holes were controlled by means of nonfriction-type survey instruments, was successfully employed.

Jan 1, 1956

By Danny Riley, Brian Curry, Sandya Govindaraju, James Bain

Hand arm vibration syndrome (HAVS) affects industrial workers exposed to long term hand-transmitted vibration from powered-tools. Peripheral neuropathy is a major component of the symptom complex of HAVS. Long term exposure to vibration causes myelin damage in peripheral nerves and reduces nerve conduction velocities in rats1. This study addresses the effects of acute vibration at constant acceleration of 49 m/s2 on myelinated fibers in peripheral nerves in Sprague-Dawley male rats using the ‘rat-tail vibration model,’ which simulates hand-transmitted vibration2. Methods Male Sprague-Dawley rats (~300 g) were assigned to vibration groups: 1 hr continuous vibration at 60 Hz; 4 hr continuous exposure at frequencies of 30, 60, 120 or 800 Hz; immediate and 24 hr following a 4-hr cumulative exposure of continuous and intermittent vibration at 60 Hz. Unanesthetized rats were restrained in cages on a nonvibrating platform with their tails placed on a vibrating stage accelerated by a B&K motor type 4809 and vibrated. Intermittent vibration was delivered in bouts of 10 min vibration alternating with 5 min rest periods repeated over 6 hr. Sham controls were restrained without vibration. After vibration exposure, the rats were anaesthetized, and the ventral nerve trunks from the proximal tail segment 7 were fixed in glutaraldehyde, embedded in epon-araldite and sectioned at 0.5 µm thickness and stained with toludine-blue for morphological quantitative analysis. The total number of myelinated axons in each cross-section of the nerve was counted using the Image J software. Myelin damage was identified by focal increase in area and intensity of toludine-blue staining and unraveling of the myelin sheath. Statistical analysis for comparing sham and the different vibration groups was done using Dunnett’s test. Animal treatment and all surgical procedures were approved by the institutional review board and compiled with the Laboratory Animal Welfare Act. Results The rats tolerated continuous vibration very well and exhibited no behavioral signs of stress. When exposed to intermittent vibration, there was increased vocalization, a startle reflex at the beginning of each bout of vibration, deposition of porphyrin around the eyes and transient hypersensitivity to touch.

Jan 6, 2006

By Van H. Manning

Chemical and physical tests of coals for the use of the Government have been made by the United States Bureau of Mines. These tests form part of a general study of the coals in the United States with respect to the manner in which each coal can be utilized most efficiently. As a result of this study, much information of value to all industries using coal has been compiled. Special investigations by the Bureau of Mines of the fuels used by the Government have, until recently, been for the most part limited to coal. In the course of these investigations the bureau has de- veloped new methods for use in the purchase of coal by the Gov- ernment. The application of these methods permits an intelligent selection of the coal adapted to the requirements of particular heat- ing or power plants, and has already resulted in the saving of large sums of money. In addition, these investigations have led to the compiling of a series of carefully made analyses of samples of coal collected in a predetermined manner in the mines of all the impor- tant coal fields in the United States, and these analyses are being published to enable Government purchasing agents and all users of coal to select the coal best suited to their needs. The purpose of this paper is to describe briefly the general char- acter and commercial quality of some of the coals mined in the United States that reach tidewater shipping ports, and to show in a general way the important characteristics of those coals that by reason of transportation facilities and the situation of the coal fields are most available for export. Coals of excellent physical character and of high heating value are available for export. For this reason and because of the modern facilities at the collieries for properly grading large shipments, American producers can supply coals suitable for any kind of service. The transportation system from the mines to tidewater and the coal- handling equipment for loading boats at the various ports are highly developed, so that producers are able to give excellent service to foreign buyers. Enormous quantities of these coals have been used by railroads, manufacturing, illuminating-gas, and coke plants, and seagoing vessels, and for household purposes. Much of the coal available for export is superior to the coals that have been supplied to foreign users from other sources.

Jan 1, 1916

By H. H. Schrenk

The purpose of respiratory protective equipment is to prevent the inhalation of harmful or objectionable atmospheres. Although constituents or contaminants that may render an atmosphere irrespirable or objectionable are numerous, they may be classified broadly as follows: I. Gaseous substance: n. A. Toxic. B. Inert (oxygen deficiency). II. Particulate matter (dispersoids). A. Solid. a. Dust (formed by disintegration). b. Pure (formed by condensation). B. Liquid. a. Mist (formed by disintegration). b. Fog (former by condensation).

Jan 1, 1940

By E. P. Dowding, J. Schlocker, C. H. Fuchsman, R. R. Lloyd, Mahan. W. M., O. C. Garst, W. T. Rawles

"INTRODUCTION The United States, although the leading consumer of chromite, depends almost entirely on imports for its supply. For instance, the consumption during. 1941 amounted to 714,645 long tons, whereas the domestic chromite production, although the highest since 1918, was 12,731 long tons or only 1.78 percent of the domestic consumption. 9/ Domestic production was tremendously, accelerated,after 1941 by war demands; however, only a small proportion of this domestic product was of sufficient quality to be substituted for the high-grade imported chromite demanded for metallurgical purpose. Chromite is used largely for making ferrochromium, an alloy containing 60 to 70 percent chromium which is used in making alloy steels. Peacetime specification for ferrochromium required that it should contain 68 to 69 percent chromium. These specification were lowered to between 60 and 63 percent, chromium in 1941 to permit the use of lower-grade ores. The specifications for metallurgical chromite, used for making ferrochromium, were established first by the Metals Reserve Company at 48 percent Cr203 and a Cr. Fe. ratio of 3 : 1 but later were lowered to 45 percent Cr203 and a Cr : Fe ratio of 2.5 : 1. The ratio of chromium to iron in chromite is important, because the contained iron enters the alloy in making ferrochromium and, although an ore may contain the required 45 percent Cr203, it may contain too much to be suitable for ferrochromium production. The principal sources of domestic chromite are California, Oregon, Montana, and Alaska minor, small, and widely scattered deposits in another dozen States. Without exception, these deposits are low-grade, require beneficiation to produce a commercial product, and are not competitive with imported high-grade ore in normal times. Nevertheless, these deposits form strategic reserve, which must be utilized in periods of national emergency. Recognizing this fact; the Bureau of Mines for many years has undertaken investigations to develop methods of utilizing domestic chromite ores. The problem has been approached from three angles: (1) Mechanical methods of concentration; (2) beneficiation by chemical or metal¬lurgical methods; and (3) production of metallic chromium by electrolysis of solutions prepared from ore or concentrate."

Feb 1, 1946

By G. M. Potter

During investigation of the occurrence of manganese deposits in the western United States, the Bureau of Mines collected 2-ton samples of 4 ores from 3 properties in northeastern Nevada. Laboratory tests were made to determine the amenability of these ores to ore-dressing methods of concentration. The Caviglia-Vietti property is situated 11 miles southeast of Ely, White Pine County, Nev. The ore deposits are lenticular veins and irregular masses found in limestone fracture zones and along the contact of limestone and underlying shale. Two samples, of the ore were tested: Lot A, from the Vietti shaft, and lot B, from the. Caviglia shaft.

Jan 1, 1954

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 15,174-acre Sleeping Giant study area, including the 6,112-acre Wilderness Study Area (MT-075-111), in order to evaluate its identified mineral resources. The study area is located in Lewis and Clark County, MT, about 30 miles north of Helena. Sleeping Giant Mountain trends west-northwest from the Missouri to the eastern crest of Little Prickly Pear Canyon (the route of Interstate 15), and has several summits over 6,000 ft. Geologically, the area is in the Disturbed Belt, and a large block of Middle Precambrian metasedimentary siltstone and underlying shale has been thrust northeast over younger, sedimentdry volcanic and intrusive rocks.

Jan 1, 1988

By E. L. Garton

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 3134, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and January and March, 1932, as published in Reports of Investigations 3140, 3147, 3150, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active Permissible list: Austin Red Diamond No. 1, L. F. Gel-Coalite W, L. F;" Austin Red Diamond No: 5. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.

Jan 1, 1932

By S. P. Holt

The Salt Chuck mine is on the east bank of the Salt Chuck, a salt-water inlet at the head of Kasaan Bay, Prince Edward Island, Southeestern Alaska. The deposit was worked at intervals from 1905 until. 1941. Early ship-ments of hand-sorted ore are reported to have assayed about 4 percent copper, 0.15 ounce gold, and 0.15 ounce silver. The total mine production up to 1941 is reported to have been 326,000 tons containing 6,200,000 pounds of copper. During December 1942 the Bureau of Mines cut a 15-foot channel sample on the surface and channel samples from headings on the 300-foot level. In July 1943 a development project was started. Thirteen diamond-drill holes totaling 1,550 linear feet were drilled from underground stations on the 200- foot and 300-foot levels.

Jan 1, 1948

The influence of fuel additives on automobile exhaust emissions was studied using engines currently found in the U.S. vehicle population. The fuel additives used in the experiment were four multifunctional additives and one lead antiknock additive. Experimental work was done to determine both the direct effect of the additive per se on exhaust emissions and the influence of Long-term additive effects on emissions with mileage accumulation. Results showed no significant direct or intermediate effect on exhaust emissions for any additives tested. In subsequent experimental work concerned with the long-term or indirect effects of additives, the detergent-dispersant additives were found to have little influence on emissions when used in conjunction with high-quality oil and motor fuel. The lead (tetraethyl) antiknock additive increased exhaust hydrocarbons approximately 12 to 17 percent during a 4,000-mile accumulation period using a base fuel containing 2 ml of tetraethyl lead per gallon. An unleaded fuel was used during a similar accumulation period with no significant increase in exhaust hydrocarbons with mileage.

Jan 1, 1971

By Eugene L. Grumer

High-expansion foam was applied to the flames of six fuels burning in a 1-foot-diameter tray. The flames of three hydrocarbon fuels were more readily extinguished than the flames of methanol, acetone, or unsymmetrical dimethyl hydrazine. The result is rationalized on the basis that heat transfer from flame to fuel surface is primarily radiative with the hydrocarbons and more largely convective with the nonhydrocarbons. INTRODUCTION Equipment for producing high-expansion foams has been developed by the Bureau of Mines to control coal mine fires.5 Recently such equipment has been redesigned for portability and has now been produced commercially for other fire-fighting applications. In May 1961, a 50-by 50-foot gasoline fire was extinguished within 2 minutes by a trailer-mounted foam unit that produced 12,000 cu.ft./min. of high-expansion (1,000:1) foam.6

Jan 1, 1962

By W. J. Boone, Will E. DeVaney, Lowell Stroud

This report is the fifth in a series presenting equilibrium vapor - liquid data for helium- bearing natural gases . It covers a 0.41 - mole - percent - helium natural gas that may be processed in the Department of the Interior's longrange helium conservation program . A Bureau of Mines phase equilibrium apparatus was used to obtain 139 samples of equilibrium vapor and liquid phases at 85 experimental conditions at temperatures from 0 ° to -299 ° F and at pressures from 100 to 500 psia . An appendix covers phase data at 100 , 200 , and 300 psia and at temperatures from -125 ° to -275 ° F for the dehydrated gas containing its original concentration ( 0.2 mole - percent ) of carbon dioxide , and the effect of a preliminary hydrocarbon trap upon subsequent vapor - liquid compositions .

Jan 1, 1964

By Charles Prasky

The Bureau of Mines investigated the conversion of nonmagnetic iron minerals to magnetic form through reduction Toasting operations. The primary objective was to obtain a concentrate that could be used as a direct shipping material for blast furnace consumption. Crude iron materials from the Steep Rock Lakes, Ontario, area were prepared into a blend of 8 parts siliceous ore, 3 parts pyritic ore, and 1 part tailings. Experimental work included laboratory reduction roasting tests, two continuous 10-day campaigns, and one 12-hour test all in a 34-inch by 36¬-foot rotary kiln. The objective of the project was achieved in producing an iron concentrate containing about 66 percent iron with over 90 percent iron recovery. Desirable operating conditions were developed in the kiln but optimum process variables were not completely established.

Jan 1, 1969

By H. B. Salisbury

As a part of a research program designed to help minimize national requirements for new mineral commodities by maximizing recovery of metals from domestic secondary resources, the Bureau of Mines investigated the development of economic methods for recovering copper and associated metals from complex electronic scrap. Three types were selected for research: (1) multiple-pin plugs and connectors, (2) obsolete aircraft radio assemblies, and (3) the magnetic fraction of shredded electronic scrap furnished by the Bureau's Avondale Research Center. The plugs and connectors, after incineration to remove plastic components and melting, yielded a brittle ingot, as did the internal portion of the radio assemblies. The brittle ingots were ground to minus 35-mesh for processing, and the magnetic material was used in the as-received condition. A process using pretreated or raw scrap as a copper precipitant in various concentrations of acidulated copper sulfate solution was developed as a means of effecting an initial separation and upgrading in the form of high-grade cement copper containing all or most of the precious metals.

Jan 1, 1981

By Robert Goldstein

A computer program for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. To provide a data base for these calculations, eleven 3-D machine models were prepared and the outputs of three luminaire types were measured. Calculations were done for thirty different configurations.

Jan 1, 1977

By R. G. Nelson

The mechanical properties of low-hafnium, arc-melted, Kroll-process zirconium are presented. The effect of temperature on the ultimate strength, yield strength, proportional limit, elongation, hardness, Young's modulus, electrical resistivity, and impact strength are shown, The effects of cold work and annealing on the tensile properties, bend radius, and formability, as determined by cupping tests, are also given, Tensile properties are compared, in part, to those obtained on earlier graphite-melted zirconium and on crystal-bar zirconium. INTRODUCTION The commercial production of high-purity, low-hafnium bearing zirconium has been achieved, and this metal is becoming available for industrial use. However, there is little published information regarding the physical and mechanical properties of this product; and, since there have been many improvements in the production and arc-melting techniques of zirconium in the past 3 years, it was considered advisable to present the properties of the vastly improved zirconium representative of current production.

Jan 1, 1954

By JOEL H. SWARTZ

During a series of resistivity measurements carried out in 1929 and 1930 a number of questions arose concerning the effect of topography on the character of the curves and the depths attained , the ratio of true depth to certain radii interpreted as representing depth , etc. To answer these questions it was decided to undertake a series of experimental investigations on artificial strata . It is the purpose of the present paper to present the results of the studies thus undertaken .

Feb 1, 1931