Search Documents

By Harry Perry, Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition , a revision which would supply up- to - date information on coal research and which would facilitate communication among organizations of similar interest seemed important . This compilation includes the names and activities of organizations of various types -government , university , private , and industry . The areas of investigation that each organization is engaged in are indicated in broad terms : Analysis and constitution , mining and geology , preparation , briquetting , combustion , high- and low-temperature carbonization , gasification , conversion to solid and liquid fuels , and health and safety . Publications issued by and describing the work of each organization are cited ; almost all of the organizations also publish results of their investigations in the technical press . Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country . Information that would improve coverage and accuracy of the next revision of the publication will be welcomed by the Bureau of Mines .

Jan 1, 1966

By Robert D. Thomson

The Bureau of Mines has compiled coal reserve data for the United States as of January I, 1974, for bituminous and anthracite coalbeds 28 inches or more in thickness to a maximum depth of 1,000 feet and for Lignite beds 40 inches thick or greater. These data were organized by State, county, coalbed, and rank. To evaluate the reserve by sulfur content, the reserve and analytical data from the Bureau of Mines energy data bank were synthesized using computer techniques. The reserve base in the Eastern States was determined to be 202.3 billion tons. Bituminous coal accounts for the greatest reserve base: 161.5 billion tons of deep-minable coal, and 32.5 billion tons of strip-minable coal. Virtually all of the anthracite reserve base, 7.3 billion tons, is minable by underground methods. All of the lignite, 1 billion tons, is strip minable. Subbituminous coal is not significant in the Eastern United States, About 14 percent of the bituminous coal reserve base, 26.5 billion tons, contains 1.0 percent or less sulfur. About 87 percent of the anthracite reserve base, 6.3 billion tons, is low-sulfur coal.

Jan 1, 1975

By Winton J. Gale

Coal pillar design has been based on generalized formulas of the strength of the coal in a pillar and experience in localized situations. Stress measurements above and in coal pillars indicate that the actual strength and deformation of pillars vary much more than predicted by formulas. This variation is due to failure of strata surrounding coal. The pillar strength and deformation of the adjacent roadways is a function of failure in the coal and the strata about the coal. When the pillar is viewed as a system in which failure also occurs inthe strata rather than the coal only, the wide range of pillar strength characteristics found in the United Kingdom, United States, Republic of South Africa, Australia, People's Republic of China, Japan, and other countries are simply variations due to different strata-coal combinations, not different coal strengths. This paper presents the measured range of pillar strength characteristics and explains the reasons. Methods to design pillar layouts with regard to the potential strength variations due to the strata strength characteristics surrounding the seam are also presented.

Jan 5, 1999

While coal occurs beneath about 18 percent of Utah, only 4 percent of the state has minable reserves. Utah's coal fields are mostly bituminous. Current coal production in Utah is largely by underground mining, making Utah unique among the coal-producing states. Most coal seams are more than 8 feet thick. Utah's coal resources are about 6.3 billion tons, 1.3 percent of the national reserve. Most of Utah's coal resources are held by the Federal Government and Indian tribes and are mined under lease. The climate of the Utah coal region is characterized by hot, dry summers and cold, relatively moist winters. Normal precipition varies from 6 inches in the lower valleys to more than 40 inches on some high plateaus. The growing season ranges from 5 months in some valleys to less than 3 months in mountainous regions. These extreme climatic conditions make reclamation difficult. Utah gained primacy when its regulatory program was conditionally approved January 21, 1981. Full program approval was obtained March 7, 1983. The Abandoned Mine Land Program was approved June 3,1983. A Federal Lands Cooperative Agreement was signed in March 1987; Utah performs all enforcement activities and some permitting activities on federal lands.

Jan 1, 1992

By John C. Machisak

THIS INFORMATION CIRCULAR covers the calendar year 1055 and contains statistical data on employment and injuries pertinent to metal and nonmetal mining and to their mills and processing plants that are voluntarily reported annually to the Federal Bureau of Mmes. This report, unlike previous publications, lists not only production and development workers but also office employees associated with mining and milling or processing. The last publication m the series, Information Circular 7798, Injury Experience in the Metal and Nonmetal Industries, 1954, also contains unpublished injury and employment statistics for 1943 through 1953. The Bureau is authorized to request data on injuries and employment from operators in the metal- and nonmetal-mining industries. The information voluntarily submitted by these operators contributes immeasurably to the promotion of safety in the mineral mining industries as it discloses the hazards to which metal and nonmetal workers are continually exposed during mineral extractive operations.

Jan 1, 1959

A computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. The system operates, interactively from a Tektronix 4014 graphics terminal which handles all input/output functions. The software is installed on a Cyber 74 computer that communicates with the terminal via telephone line.

Jan 1, 1978

By James C. Barker

In 1981 and 1985-1986, the Bureau of Mines conducted orientation studies of marine placer platinum-group metals (PGM). PGM are derived from the Goodnews Bay ultramafic complex and magnetic surveys show that the complex extends offshore at least four mi. The present seafloor was an emergent foreland as recently as 8000 years ago. High-energy ocean processes are transporting and depositing sediment such that PGM-bearing materials are reworked and later masked by barren littoral drift. Exploration targets include 1) placers formed since present transgression began, and 2) ancient marine and drowned fluvial deposits. Additionally, there is evidence of PGM solution transport and accretion. At least minor values of PGM in Recent lag-type placers and possible submarine strands are concentrated along an offshore scarp incised through glacial deposits into the preglacial surface between Flat Cape and Red Mountain. Other Recent PGM-bearing features include Flat Cape shoal, Chagvan Bay, Salmon River delta, and modern beaches. Ancient placers include possible N-S fluvial systems 2 to 3 mi offshore, a nearshore scarp 50 ft below sea level, and strands adjacent to projected ultramafic bedrock slopes. The existance of ancient placers is dependent on depth of glacial erosion. SEM studies show PGM are principally isoferroplatinum and osmiridium, with minor sperrylite, moncheite, and platiniridium. Gold is a co-product, and concentrates comprise chromite, ilmenite, and magnetite. Beneficiation tests successfully concentrated precious metals from natural blacksand accumulations, but failed to concentrate low-grade lag gravels.

Jan 1, 2011

By Kung-Lee Wang

The 1963 performance of the United States economy was impressive. The year was one of continued growth unmarred by a recession. By the end of 1963 the economy's expansion had already lasted almost as long as the 1954-57 upswing, and the net gain in output since the trough in activity in early 1961 compared favorably with most earlier postwar cyclical advances. There was no indication of any slow- down at yearend. Both gross national product (GNP) and national income in 1963 were 5 percent higher than in the previous year. GNP totaled $584 billion, a gain of $28 billion over 1962. Real output of goods and services rose 3.4 percent over the year. Price increases continued to be moderate. Production, employment, personal income, and corporate profits all registered new but unemployment continued high at 5.5 percent and the prospects for improvement remained poor. The economy again failed to use its full potential. Current value of mineral production kept pace with the economy. The constant dollar value of mineral production gained more than real GNP because of the relatively stable price of minerals. Mining production achieved a new high in 1963. Steel production totaled 110 million tons, 12 million tons above 1962, making 1963 the first 100- million-ton year since 1957 and lifting the steel-associated minerals group upward. The gain in ferrous metals mining was insufficient to compensate for the decline of nonferrous metals mining resulting in an insignificant decline in the metal mining total as a whole. The upsurge of construction material minerals output, with an assist from chemical and fertilizer minerals, accounted for peak production of

Jan 1, 1964

By Neil J. Mansfield

Tool manufacturers are required to provide declarations of vibration emission values in order to sell their tools within Europe. To ensure that users can compare results obtained from different manufacturers, the declared values must be obtained using a methodology as specified in the relevant test code (such as in the ISO 8662 series of standards). In most cases, the vibration emission values obtained using test codes under-estimate the vibration that an operator will be exposed to when using the tool on a work-site. A further problem with manufacturers’ data is that usually only a single value is provided for a tool. This is despite many factors affecting the vibration emission, including inserted tool type, work piece, operator technique, tool condition. New improved test codes are in the process of being developed. In order to provide guidance to users on how to interpret manufacturers’ data, a Draft CEN Technical Report (Draft CEN/TR 15350 (2005)) was developed. Part of the CEN/TR provides multiplication factors for combinations of task and tool type. For example, data obtained from electrical hammer drills (tested according to EN 60745-2-6:2003) should be multiplied by 2, for hammering applications, in order to obtain an estimate of the vibration emission during work. In response to concerns from industry, the UK trade association OPERC have, in collaboration with hire companies and tool manufacturers, established a freely accessible online database of tool emission values based on independent tests carried out under simulated work-site conditions. This paper reports some of the data obtained from electrical hammer drills, highlighting the range of emission values that can be obtained for a tool. Data from many other tool types are also included in the database. Methods Tri-axial hand-arm vibration was measured at both handles of each of 19 electrical hammer drills, in accordance with ISO 5349-1 (2001). Each tool was measured with three experienced operators and at least 5 runs were completed for each operator. Tools were tested using a range of appropriate new bits from 4 to 40 mm diameter. The minimum number of bits for a tool was 3; the maximum number was 29. 146 tool / bit combinations are reported here, representing about 2200 individual 6-axis measurements. Operators were required to drill vertically into a concrete block with a compressive strength after 28 days of 40 N/mm². Two drills (1 and 15) were battery powered; others were powered using a 110V transformer supply.

Jan 6, 2006

By Thomas E. Marshall, Roy H. Grau

The U.S. Bureau of Mines has developed an acoustic test for determining if a rock salt sample is from a "normal" nongassy salt face or from a gassy face where an outburst has the potential to occur. The test is based on the observation that a salt sample taken near an outburst-prone zone produces an audible popping sound when it is dissolved in water. The sound is produced when pressurized gas that is trapped in salt samples is released. In the acoustic test, the sound is electronically measured, digitized, and transmitted to a microcomputer; the output is an average decibel value that classifies the sample as "normal" or "outburst." The acoustic test procedure and equipment are described, and raw test results and data analysis are shown. Results are also shown for several salt samples that were analyzed using a laser Raman microprobe.

Jan 1, 1990

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By J. H. Perry

The Bureau of Mines is conducting research to determine the effectiveness of long holes in degasifying an area of the Upper Split of the Lower Sunnyside coalbed at Kaiser Steel Co.'s Sunnyside No.1 mine. These holes were drilled from the two outside entries of a section that was closed to mining because of excessive methane emissions. Two holes drilled to 430 and 450 feet produced initial gas flows of 160,000 and 127,000 cfd, respectively. Sixteen days after the completion of the second hole, the total gas production declined to just over 144,000 cfd. In 9 months of degasification, over 35 MMcf of commercial-quality gas has been removed from the coalbed. The combined gas flows declined to 106,000 cfd in the 9-month period. The two holes have reduced face emissions by about 40 pet.

Jan 1, 1978

Three types of communication systems have become popular in solving communication requirements underground: Loud-speaking pager phones, carrier current phones, and magneto ringing phones. Basically, all three are simply single-channel party line systems. Although these systems are quite reliable, the single channel creates a variety of problems. For example- 1. Since no call is confidential, messages are sometimes purposely made vague, especially if accidents or safety topics are being discussed. 2. A potential user must literally "wait in line" until the channel becomes clear for his use; thus, when foremen have to wait to call in reports or supply requests, this single chan-nel creates a serious productivity bottleneck. 3. In many large mines, there are independent branch lines that must be tied together by a dispatcher, adding further delays to the system. To solve these problems, some mines have installed other phone systems-mostly commercial dial phones in industrial enclosures that offer extra channel capacity and private line features. Others have installed a system that combines both dial- and page-phone features in a single unit. Although these do represent improvements, they do not truly solve the overall problems that face modern mines. Besides extra channels, a communication system should have the following features to enhance productivity and safety: 1. A means of paging a roving miner to alert him that he is wanted on the phone. 2. Wireless-to-wired system interconnects by which a miner can talk on the wired phone system by using a remote portable radio. 3. Remote monitors that alert personnel when there is a toxic or explosive gas buildup. 4. Control interfaces that allow remote control of fans, pumps, or other devices. 5. Transmitters and receivers that can serve as emergency links. 6. Loopback that allows an alternate path of communications if the main path is cut. This chapter focuses on equipment and methods to meet the special communication needs of individuals in various places of the underground mine. The communication requirements can be broken down into four categories: 1. The mine entrance (shaft communication). 2. Permanent and semipermanent locations (shop areas, lunchroom, crusher stations, etc.). 3. Mining areas (the room-and-pillar sections, longwall faces, block caving areas, etc.). 4. Haulageways (tracked trolley haulage, diesel, belt haulage). Methods of implementing systems to meet the communication needs of these areas are described in sections 3.2 through 3.5. Section 3.6 discusses methods of satisfying special communication requirements that exist. Major topics in this category include communications with roving personnel, the isolated miner, and motorman-to-snapper communications. Emergency communication systems are described in section 3.7.Detecting and

Jan 1, 1984

By Alexander Siefert, Steffen Pankoke

In the development of commercial vehicles as well as of passenger cars, the effects of vehicle vibrations on operating safety, health and comfort can only be predicted by numerical simulation when appropriate occupant models are available. Such models must be based on human anatomy and have dynamic properties of real humans in order to achieve realistic results. Since human dynamic behavior depend on posture and percentile, the occupant model needs to be adjustable to these parameters with respect to geometry and dynamic properties [1,2]. Dynamic Human Finite-Element-Model CASIMIR CASIMIR is a non-linear, dynamic finite-element-model of the human body. It consists of a dynamic model of the upper torso with head, neck, shoulders and arms as well as of a dynamic model of the lower extremity with pelvis and legs. The most important part is the lumbar area with dynamic non-linear models of the lumbar spine and of back and abdominal musculature. The frequency-dependent characteristics of the intervertebral discs and the effects of muscle activation and non-linear frequency-dependent muscle properties are included. In the latest stage of development, CASIMIR has been equipped with a compliant model of the body surface in the contact areas to the seat. This results in a very realistic transmission of static and vibrational forces into the human body, see fig. 1. Intense model verification and validation has been performed in all stages of model development, starting with validation of small components like intervertebral disc, ending with validation of whole-body-vibrations using measurements of the dynamic mass / mechanical impedance [4]. For an in-detail examination of stresses in the vertebral bodies and discs, a non-linear submodel of the lumbar spine with an increased number of degrees of freedom can be coupled to the whole-body-model, enabling the researcher to examine local effects of vibrations and single shocks on the lumbar materials. [ ] Since it is well known that human dynamic behavior is significantly affected by anthropometric data and posture, CASIMIR can be individualized to the anthropometric status of single individuals or to the mean values for specific percentile groups. Furthermore, posture can be adjusted to the seating conditions applicable to a specific vehicle. Posture modification capabilities include the variation of the lumbar lordosis [3].

Jan 6, 2006

By Roy E. Williams

1. The major sources of heavy metal ions in wastewaters of the Coeur d'Alene Mining District are effluents from metallurgical processing plants. Effluents from mine operations provide a secondary source for heavy metal ions. Based on data analyzed by the Federal Water Quality Administration, mercury and arsenic are escaping from some mill waste ponds, but they are in the suspended phase. 2. Metallurgical process effluents are combined with mine waste effluents in tailings ponds, consequently, the quality of the tailings pond decant water is highly degraded. The major effect of combining metallurgical process effluents with mill wastes is a drastic change of pH in the tailings pond. This chance may be an increase or a decrease depending on the metallurgical process. The effluent from an electrolytic antimony plant drastically increases the pH in the tailings pond permitting the removal in solution of antimony via the pond decant system. The addition of low pH effluents to the tailings ponds results in a net decrease in pH which makes lead, zinc, cadmium, and copper more soluble, thereby permitting their removal from the pond via the decant system.

Jan 1, 2011

By D. B. Dow

This report on methods employed for dehydrating oil-field emulsions, is the second of a series prepared as a result of a study of oil-field emulsions recently completed by the writer. The first paper2 dealt with the factors responsible for the formation of emulsions. A third paper will discuss the physical chemistry involved in the formation and resolution of such emulsions. In the early development of the oil fields of Pennsylvania, no emulsion troubles of any consequence were encountered, nor to any serious extent in the oil fields of other Eastern States: However, with the development of fields west of the Mississippi in Oklahoma, Kansas, Texas and California, where heavier oils of different characteristics were found, the problem of dealing with cut oil soon became of great importance.

Jan 1, 1925

By James W. Ballard

The facts are generally accepted that an atmosphere containing large quantities of any dust is objectionable to breathe and that some dusts are more dangerous than others. Therefore, knowledge of the composition of dusts is important in evaluating the hazard entailed on exposure. At present, free silica, of which quartz is the most abundant form, is considered one of the most significant dusts, from the standpoint of pneumoconiosis, and one State5/ has established permissible limits of air dustiness on the basis of the free-silica content of rock. The amount of free silica in materials used for rock dusting also has been limited.6/ Determination of free silica or quartz, therefore, is important.

Jan 1, 1940

By Sean Gallagher

Bolting large sheets of wire mesh screen (WMS) to the roof of underground mines prevents injuries due to rock falls. However, WMS can be heavy and awkward to lift and transport, and may result in significant spinal loading. Accordingly, six male subjects (mean age =45.8 years + 7.5 SD) were recruited to lift WMS in a laboratory investigation of the biomechanical demands. Biomechanical modeling was used to estimate external moments about L5-S1 for sixteen lifting tasks, using two sizes of WMS. Full-size WMS involved a two-person lift, while half-size WMS involved a one-person lift. Lifts were performed under 168 cm and 213 cm vertical space. Restriction in vertical space increased the maximum L5-S1 extensor moment from 254 to 274 Nm and right lateral bending moment from 195 to 251 Nm. Lifting full sheets of screen (as opposed to half sheets) resulted in an average 33 Nm increase in L5-S1 extensor moment. The L5-S1 extensor moment was increased by an average of 44 Nm (18%) when lifting screens positioned flat on the floor compared to an upright position. Relevance to industry: Large flexible materials are commonly lifted in industrial work environments, and may involve the efforts of two or more workers. The current study examines the low back loading associated with lifting large flexible screens and presents recommendations to reduce spine loading.

Jan 1, 2009

By Joseph Cervik, Gerald L. Finfinger

This Bureau of Mines publication reviews underground methane drainage pro- grams being conducted in various coalbeds. Equipment used in drainage programs such as drills, underground pipelines, and methane monitoring systems is described.

Jan 1, 1980

By Thomas M. Barczak

The U.s. Bureau of Mines is conducting research to optimize the utilization and design of mine roof support systems. This report describes methods to evaluate resultant loading on longwall shields, defined as external resultant vertical and horizontal force acting on the canopy and base. Four models are considered: two rigid-body models, an elastic model, and a numerical model. The rigid-body models equate measured internal shield forces to unknown external resultant shield forces (loads) through rigid-body analysis of static equilibrium requirements. The elastic model develops a solution to shield mechanics by evaluation of the load-displacement relationship and stiffness characteristics of the support structure. The numerical model is a two-dimensional finite-element representation of a shield structure. Model determination of resultant shield loading is compared to controlled loading of a shield in the Bureau's mine roof simulator. Parameters investigated are shield height, canopy contact configuration, canopy and base horizontal constrainment, and boundary conditions imposed by vertical and horizontal shield displacements. It is concluded that rigid-body models are most applicable to in situ measurement of shield loading. Applications requirements and potential error sources are discussed.

Jan 1, 1990