Search Documents

The coal-bearing areas of Kansas cover approximately 18,800 square miles (23 percent of the state's total area). Coal in Kansas ranges from lignite to high volatile bituminous, located principally in the south-eastern part of the state. Kansas reserves are estimated to be 987,500,000 tons, approximately 0.2 percent of U.S. reserves. Coal beds generally occur in thin seams up to five feet thick. The overburden-to-coal stripping ratios in Kansas are among the highest in the nation, typically 20 to 1, with some ratios up to 35 to 1. The first commercial coal mining operation in Kansas opened in 1865 at Fort Scott in Bourbon County. As in other states, coal production in Kansas increased during the industrial revolution, and then fell as industry converted to alternative fuels. Production peaked in 1916 and 1917, with annual production of 7,250,000 tons. Coal production today is by surface mining methods. The Kansas regulatory program was approved April 14, 1982; the Abandoned Mine Land Program was approved February 1, 1982; and the emergency program authority was approved January 10,1989.

Jan 1, 1992

By R. H. Fewkes

New information on possible resource value of sea floor manganese nodule deposits in the eastern North Pacific has been obtained by study of records and collections of the 1972 Sea Scope Expedition. Nodule abundance (percent of sea floor covered) varies greatly, to judge from bottom photographs from 8 stations and data from other sources. All estimates considered reliable are plotted on a map of the region. Similar maps show the average content of Ni, Cu, Mn, and Co at 89 stations from which 3 or more nodules were analyzed. Variations in nodule metal content at each station are shown graphically in an appendix, where data on nodule sizes are also given. Results of new analyses of 420 nodules from 93 stations, for Mn, Fe, Ni, Cu, Co, and Zn, are listed in another appendix. Relatively high Ni+Cu content is restricted chiefly to four groups of stations in the equatorial region, where group averages are 1.86, 1.99, 2.47, and 2255 weight percent. These and a few other areas may warrant more exploration. It is hoped that this report will stimulate new interest in North Pacific nodule deposits and that the maps and quantitative data will aid future exploration.

Jan 1, 1981

By W. K. Kleysteuber

This report covers the design and testing of a novel bulk materials conveying device by the Bureau of Mines. The transport concept of the device is to create a traveling wave with a steep front so that the bulk material slides and cascades down the front of the wave with some horizontal motion. Ideally, the front should act like a continuous chute. The concept of moving bulk materials along a belt without any forward movement of the belt itself was demonstrated. The conclusions reached were that the mechanism as designed could not overcome the inherent major disadvantages that would make the undulatory conveyor suitable for practical applications.

Jan 1, 1974

By Thomas P. Dolley

Building stone, cassiterite, kaolin, gold, lime, and peat were the only commodities mined, The country's main economy was in agriculture, primarily in coffee exports. Tribal violence occurred again, between the Hutu and Tutsi tribes, causing an estimated 50,000 deaths, mainly in rural and mining areas. The inflation and a large deficit continued. The country continued to import cement, fertilizers, oil, and petroleum products. Burundi possessed numerous small gold deposits. The northwest and north-east were the country's two most important gold-bearing regions. A large kaolin deposit was found at Ngozi, and its mining was specified in the fifth 5-year development plan for 1988-1992. In the area of Rugombo, limestone was being explored with the intention of opening a cement plant.

Jan 1, 1990

By O. C. Blade

The southeastern region of the United States is becoming more important as a petroleum-producing area, and it is receiving increasing attention from oil operators. In 1948 total production of crude oil from six southeastern States - Alabama, Florida, Kentucky, Mississippi, Tennessee, and Virginia - was 55,244,000 barrels, which represents 2.7 percent of the Nation's output during that year. Kentucky and Tennessee have produced crude oil since the early days of the industry, but the remaining four States have had production only few years. Data on annual production of crude petroleum in the six States are given in table 1.

Jan 1, 1950

By D. A. Paice

A power supply to operate fluorescent or mercury vapor lamps from 300 volt dc coal mine trolley wires has been developed for the Bureau of Mines. A high frequency regulated inverter unit incorporates ballasts for a mix of lamp loads up to 650 watts. For 600 volt trolley systems an additional power converter unit was developed to step down the dc voltage to 300 volts for the inverter unit. Both units have operated in a working coal mine for over 12 months without need for servicing. The lamp load in these tests included two 100 watt mercury vapor head lamps and six 75 watt fluorescent lamps.

Jan 1, 1979

By John J. Henn

An evaluation is presented of the Bureau of Mines process for the recovery of metal and mineral values from municipal incinerator residues. This process employs standard mineral beneficiation techniques and is operating on a pilot-plant scale of 1,000 pounds of incinerator residue feed per hour. Products from this separation process include ferrous, aluminum, and copper-zinc scrap, and colorless and colored glass. Cost estimates were prepared for four plant sizes. The estimated capital and operating costs For the four plants follow: [ ] It is assumed that the separation plant is located adjacent to a municipal incinerator. Provision is made, however, for part of the residue feed to be delivered by truck so that one large separation plant can be used for residue from more than one incinerator.

Jan 1, 1971

By Richard A. Walker

This report describes the development and performance of a multi-level, multi-function Calibration Light Source designed for field-calibration of a group of specific photometers. The Calibration Source is capable of providing ±35% accuracy calibrations at all of the following levels: 0. 05 foot-Lamberts, 6 foot-Lamberts, 6 foot-candles and 20 foot-candles. The Source was found to provide constant light output to within 1% over 50 hours of lamp operation and for line voltage variations of ±25%. It is compact and light-weight (11 pounds), and can be easily transported and used by one man in normal office environments (without requiring a darkroom).

Jan 1, 1976

By H. D. Bemis

This paper describing the milling practice of the American Metal Co. at its Pecos con¬centrator is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. ACKNOWLEDGMENT The author acknowledges the assistance rendered by Guy Martin, metallurgist, H. E. Brown and J. H. Hastings, chemists, and Thomas J. Fahey, accountant, in gathering and pre¬paring the data presented in this paper.

Jan 1, 1932

By J. H. Wiggins

The evaporation of crude oil without doubt causes one of the largest single losses to which the oil is subjected after it is taken from the ground. The few days during which crude oil is stored on the lease before being taken by the pipe line, causes an aggregate loss per year from evaporation estimated at 122,100,000 gallons of gasoline in the Mid-Continent field alone. This has a value, at 22 cents per gallon, of $26,880,000 and represents about 3 per cent of the total gasoline produced in the United States from all fields and all sources. The following table shows this in more detail:

May 1, 1920

By W. E. Lamont

Flotation studies of phosphate-bearing waste pond materials, low-grade washer products, and raw ores, all from the Tennessee brown phosphate district, showed that these types of materials could be treated without des liming to recover high-grade phosphate concentrates. The investigation showed that fine grinding before flotation was a requisite for increased recovery of the phosphate values and that the optimum pH conditions were in the range of 10.0 to 10.5 when using anionic collectors. Multiple-cleaning of the rougher phosphate concentrate was required to produce high-grade concentrates. Phosphate recoveries ranged from 60 to 82 percent and were inversely related to the grade of concentrate produced.

Jan 1, 1972

By James P. Rider

This U.S. Bureau of Mines report describes a viewing transformation algorithm that generates a perspective view of a three-dimensional scene. This tool may be used by researchers to improve mine safety by assessing the visual capabilities of a mobile equipment operator. Three-dimensional transformations used to build the viewing transformation and techniques used to project the image onto a two-dimensional display screen are defined. The algorithm is written in the C-programming language and designed to stress portability, allowing it to work without significant modifications on numerous computers. A listing of the computer routines along with sample output is included in the report.

Jan 1, 1992

By Dana C. Reinke

Water well drillers are exposed to high levels of noise while working. NIOSH researchers have found that water well drillers are exposed to levels above 85dB (A) while performing certain tasks during a typical drilling job. Noise levels consistently over 85dB (A) during an 8–hour work shift are hazardous and can lead to hearing loss in workers. Finding ways to reduce noise exposure is difficult because of many factors. The work environment is constantly changing due to the location of jobs and environmental factors. The types of drill rigs required for drilling are expensive. Equipment can range from new to used (10 to 30+ years old). Drillers and owners can work together to prevent noise–induced hearing loss, and measures can be taken to reduce exposure to hazardous noise.[ ] Preventing hearing loss occurs through three stages. The first stage is removing noise from the source (i.e., drill rig). Various parts of a drill rig create noise besides the drilling rod. NIOSH researchers have examined noise levels of drill rigs. Some of the loudest parts of the drill rig include the compressor, engine, and cooling fan (Fig. 1). While removing the noise source from a worksite is ideal, the process would be expensive and difficult.[ ]

Jan 9, 2005

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011

Ecuador a gross domestic product (GDP) grew 8% despite a slowdown in production and sales of petroleum, the dominant economic sector. Crude petroleum exports, which amounted to about 35% of total exports in 1977, were valued et $484 million,2 a decrease of 14% from 1976 values. Petroleum export sales were depressed because foreign buyers were somewhat uncertain that State-owned Corporación Estatal Petrólera Ecuatoriana (CEPE) held legal title to the oil until final settlement with Ecuadorian Gulf Oil Corp. In addition to the legal complication, Ecuador maintained a relatively high export price for oil until late in the year. There was also a shrinkage of traditional U.S, markets owing to the Alaskan pipeline becoming operational and an increased availability of Mexican supplies. The export market was also affected by increased domestic production in Peru and Chile, which lessened their import needs, and the pressure of greater competition from the Middle East in supplying crude oil to Caribbean refineries. About 20.4 million barrels or 40% of Ecuador's total crude exports went to the United States. Only 27 wells were drilled in Ecuador during L977; of these, 16 produced oil, 3 were dry holes, and 8 were suspended. About 31 wells were planned for 1978. Three new oilfields were discovered during 1977; two by CEPE in northeastern Ecuador and one by the Argentine State oil company Yacimientos Petraliferos Fiscales (YPF), operating in Ecuador under a service contract. CEPE's two discoveries tested at 5,000 and 1.450 barrels per day, respectively. The YPF discovery tested at about 1,000 barrels per day. Ecuador altered its position regarding

Jan 1, 1981

By A. C. Fieldner

"Gas hazards may be divided into two principal classes- namely (1) inflammation and explosions; (2) asphyxiation and poisoning. Inflammation and explosion are prevented first by adequate ventilation so that gas sufficient to propagate flame or explosion can not accumulate, and second, by avoiding sources of ignition such as open lights, flames, sparks, electrical arcs, short circuits, or sparks. Ventilation is also the best preventive measure against asphyxiation and poisoning from toxic gases. When men must enter unventilated or poorly ventilated places containing poisonous or asphyxiating gases, suitable gas masks, hose masks, or oxygen breathing apparatus should be worn. As a rule, loss of life and property from gas hazards is due to ignorance of the properties and hazards of various gases commonly used, and consequently a failure to use proper measures for eliminating and meeting these dangers. It is the purpose of this paper to describe briefly the common gases and vapors with respect to the hazards involved in their use and to discuss the necessary precautions and methods for avoiding these dangersLight, heat, and power are prime essentials of our modern industrial civilization. The combustible gases and vapors used for the production of these necessary elements of our existence comprise the largest and most common group of domestic and industrial gas hazards. Almost every individual in his daily life subject to possible danger from asphyxiation, fire, or explosion due to one or more of these gases. For evidence one need only refer to the daily newspaper where headlines such as the following are frequently seen; ""Family asphyxiated by carbon monoxide from gas heater;"" ""Schoolhouse wrecked by gas explosion in basement;"" ""Man killed by automobile exhaust fumes in his garage;"" ""Fireman overcome by smoke fumes in basement ""Woman"".""Boman severely burned by accidental ignition of gasoline used in cleaning gloves;"" and 'in recent Years we often see ""Building wrecked by explosion of still in residential district.""It will be noted that these accidents are due to inflammation, explosion, or asphyxiation. Any combustible gas or vapor, when mixed, with air or oxygen within certain limiting proportions, will explode on ignition. The violence of the explosion varies with respective proportions of air and gas, and with the degree of confinement of the mixture. For example: Mixtures of natural gas and air containing between 4.5 and 12 per cent natural gas will explode, or propagate flame throughout the mixture without the continual presence of the source of ignition that started the inflammation. The table following gives the explosive limits of the common combustible gases and air:"

Jun 1, 1926

By S. R. Zimmerley, John Gross

"The investigation discussed in this paper was undertaken to obtain fundamental data on crushing and grinding and has been confined, so far, to work on quartz.The results of crushing or grinding have hitherto been judged entirely by the amount of the various-sized particles produced, based. on sieve sizing for particles above 74 microns in size and on microscopic measurement or elutriation for particles below 74 microns - a method which could give only a general idea of what had been accomplished.There was a distinct need of a ""yardstick"" for the measurement of crushed material. It appeared that no advance in the fundamental investigation of crushing and grinding could be made without a reliable method of surface measurement and that such a measurement would have to be based on some property of the surface of the crushed material.A number of attempts based on various surface actions, such as adsorption and heat of wetting, were made to measure surface on quartz particles, but all gave unsatisfactory results. After some preliminary work it was decided that a dissolution method based on Wenzel's law-- ""the reaction velocity between solids and liquids is proportional to the area. of contact""4 -- would be the most feasible.Early use of the dissolution method had been made for surface measurements5, and lately Dr. Geoffrey Martin and his coworkers in England used the dissolution method to determine surface on quartz. They compared the amount of quartz dissolved from a sample in one hour by a hydrofluoric acid solution, with the amountdissolved from a measured quartz cuboid6,After investigating the solvent power of sodium carbonate, sodium hydroxide, and hydrofluoric acid for quartz, hydrofluoric acid was selected as the most suitable solvent, and a dissolution method was developed which gives very reliable results.During the dissolution of quartz in hydrofluoric acid, the reaction velocity changes for two reasons: there is a change in concentration of solution, and a change of surface of the solid. The amount of quartz dissolved in a definite period of time is therefore not a true measure of surface. If, however, the reaction velocity or rate of dissolution for various periods of time be plotted, a curve will be obtained which, if extrapolated to the zero time ordinate, will give the rate of dissolution before any change of surface or any change in the solvent has taken place, and which is a true index of surface. This rate of dissolution, expressed in percentage of the original sample at the zero time ordinate, is designated herein as the ""Initial Rate"" or as simply ""I. R."""

Jul 1, 1928

In 2005, a total of 739 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.0% of all operations. ? Mines producing common clay comprised 26.9% (n=199) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the Virgin Islands.

Jan 1, 2008

By Avery H. Reed

RECORD production of marble, kaolin, scrap mica, and talc high-lighted the mineral industry of Alabama in 1962. Among the States, Alabama ranked second in scrap mica, third in the production of bauxite and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by mining and processing of coal and iron ore, and the manufacture of cement, which together comprised 73 percent of the total value of production, compared with 72 percent in 1961. Other important industries were the production of crude petroleum, and stone quarrying. Leading companies were Tennessee Coal & Iron, Southern Cement Co., Southeastern Electric Generating Co., Alabama By-Products Corp., and U.S. Pipe & Foundry Co.

Jan 1, 1963

On July 1, the Bonneville Power Administration announced a 25% power cutback because of lower than normal stream flow. In September, the Aluminum Company of America (Alcoa) announced plans to shut down one 23,000-ton-per-year potline at its Vancouver, Wash., primary aluminum smelter. Alcoa also announced that the last of four potlines at its Point Comfort, Tex., primary aluminum smelter would be restarted in October. A new 3-year contract was signed and workers at three Alcan Aluminum Ltd. primary aluminum smelters in Canada returned to work. It was estimated that it would take about 3 months before the smelters were operating at full capacity.

Jan 1, 1979