Search Documents

By D. E. Shanks

As part of its program to lessen dependence on foreign bauxite as the Nation's primary source of cell-grade alumina, the Bureau of Mines is investigating sulfuric acid (H2S04) leaching procedures for the recovery of alumina from domestic aluminous materials. The successful application of a H2S04 leaching process depends on the recovery of the aluminum values in an easily washed and filtered form, containing a minimum of water to be driven off in the subsequent calcination step. This goal was met by the high-temperature hydrolysis of simulated aluminum sulfate [A12(S04)3] leach liquor. Crystalline, insoluble aluminum hydroxy sulfate [A1(OH)S04], which had a water-to-alumina mole ratio of 1:1, was produced. Eighty-six percent of a solution containing 127 g of A12(S04)3 per liter and 76 pct of a solution containing 336 g of A12(S04)3 per liter were hydrolyzed to insoluble aluminum hydroxy sulfate by autoclaving for 1 hr at 320° C and rapidly quenching to room temperature. Higher operating temperatures were precluded by corrosion of the autoclave. The yield of aluminum in the hydrolysis product increased with increasing hydrolysis temperature and decreasing A12(S04)3 concentration.

Jan 1, 1981

By Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion-proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures,a multi compartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 2010

By E. H. Denny

Colorado coal-mine fatalities, which have gradually decreased since 1914, have shown a marked decline since 1924. Data on coal-mine fatalities in Colorado published by the U. S. Bureau of Mines5 indicate that the deaths per thousand 300-day workers have decreased from 9.13 in 114 to 6.14 in 1926, and that the deaths per million tons produced have decreased from 9.18 in 1914 to 4.98 in 1926. Table 1 gives fatality rates in Colorado and in the United States from 1914 to 1926 inclusive. [ ]

Jan 1, 1929

By Homer J. Ballinger

The Rex mine is one of several zinc deposits in Ozark and Howell Counties, Mo. It is the second of these deposits investigated by the Bureau of Mines in an effort to demonstrate reserves of sulfide ore underlying the shallow carbonate ores from which the district's major production has come. The initial investigation was made during 1945-46 on the Alice mine, Ozark County, Mo.21 The investigation reported herein was conducted during 1947. The Rex open pit is about 250 feet long, 100 feet wide, and about 25 feet deep (average). Three caved shafts are evident in the bottom of the pit, but the extent of the workings from these shafts is not known. The Bureau of Mines drilled five churn-drill holes in and around the Rex pit to test the grade and the vertical and lateral extent of the deposit. Two of the holes indicate notable zinc mineralization ranging from less than 1 to more than 10 percent metallic zinc, but largely in the oxidized condition.

Jan 1, 1948

By Arthur J. Hudson, Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion- proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures, a multicompartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 1992

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By X. Shi, V. Vallyathan, N. S. Dalai

"Using. ESR spin trapping methodology, evidence was obtained that fresh quartz dust in a cell-free aqueous medium generated hydroxyl - and possibly superoxide radicals. The hydroxyl radical generation potential decreases on storing of fresh quartz dust in ambient air and on the addition of either catalase, superoxide dismutase, desferoxamine, or DMSO. The role of quartz related radicals in the biochemical mechanism of acute silicosis is suggested from these findings.IntroductionThis report summarizes our electron spin resonance (ESR) detection of oxygenated radical formation by freshly crushed quartz particles in a cell-free aqueous medium, and its inihibition by radical scavengers. This study was undertaken with to elucidate the primary biochemical mechanism involved in the development of silicosis (Farber, 1983; Reiser and Last, 1979; Silicosis and Silicate Disease Committee, 1988). In particular the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still not well understood (Farber. 1983; Reiser and Last, 1979;). It is generally believed that the action of quartz particles on the cell membrane is the starting point of the silicotic process (Farber, 1983; Parazzi et al., 1968). Thus the surface characteristics of the quartz particles have been the subject of several recent studies (Bolls et al.. 1983; Dalai et al., 1986; Fubini et al., 1987). Recently, We reported that mechanical crushing of quartz under normal atmosphere generates free radicals which decay with time, and that these free radicals are associated with a higher cytotoxicity of fresh quartz dust as compared to aged dust from the same stock (Dalai et al., 1986; Vallyathan et al.. 1988). The formation of Si• and. SiO--type of radicals from quartz particles crushed under atmospheric conditions has also been reported by Fubini et al. (1987). In addition, Gulumian and van Wyk (1987) have reported that quartz particles react with hydrogen peroxide (H202) to generates hydroxyl radicals (•OH) and suggested that this process might contribute to quartz's pathogenicity. However, these authors did not report the effects of metal chelators, so it was not clear as to whether the detected -OH radicals simply resulted from the Fenton reaction involving exogenous metal ion contaminants. Earlier, Marasas and Harington (1960) reported that quartz particles could function as an oxidant in a number of in vitro oxidations, including the hydroxylation of proline and lysine. They postulated that silica dusts, on reacting with water, could release H2O2 which might have the potential to react with various biological constituents and thus cause tissue damage. In fact, Gabor and coworkers (Gabor and Anca, 1974; Gabor et al., 1975) suggested that the cytotoxicity of quartz particles might be associated with the generation of some 'factor or factors possessing the properties of a free radicals capable of promoting the peroxidative chain cleavage of polyunsaturated fatty acid moieties of the phospholipids in the cell membrane. More recently Weitzman and Graceffa (1984) reported that asbestos is able to catalyze the generation of • OH radicals from H2O2. Their later work indicated that lipid peroxidation may be one of the mechanism by which asbestos produces tissue injury (Weitzman and Weitberg, 1985). This is significant because • OH radicals are capable of causing peroxidation by abstracting hydrogen atoms from cell-membrane lipids and initiating lipid peroxidation in lysosomal membrane (Fong et al., 1973). In fact, the formation of oxygenated species in reactions involving quartz was suspected since Kolbanev et al. (1980) reported the detection of H2O2 in the reaction of fresh quartz particle with aqueous medium. The present work was thus undertaken to detect the anticipated formation of some oxygenated, radical species by reactions of quartz in a cell-free media and its inhibition by radical"

Jan 1, 1988

By W. M. Myers

The U. S. Bureau of Mines conducted an investigation to determine the cause of the deterioration of Portland cement during storage and transportation , and to discover a means of preventing it . All available printed sources of information on this subject have been examined and a bibliography has been compiled . The subject has also been discussed with the leaders in the cement industry ; the present report is the result of their cooperation , and is based principally on information thus obtained . Deterioration of Portland cement during storage over any considerable period of time has long been noted ; closely related to it is deterioration of cement during transportation, which involves not only the time factor of storage but also exposure to varied climatic conditions . Deterioration in both cases is due to hydration of the cement by absorption of moisture from a humid atmosphere , or by exposure to actual rain-fall . After hydration cement possesses no cohesive power ; the degree of deterioration is directly proportional to the degree of hydration . The amount of deterioration of Portland cement during storage has been accurately determined in an investigation by the Structural Materials Research Laboratory , in cooperation with the Portland Cement Association . Cement stored in a shed in cloth sacks retained 80 per cent of its original strength after three months storage ; 71 per cent after six months ; 61 per cent after one year ; and 40 per cent after two years . The deterioration of Portland cement during storage and transportation was noted particularly in France during the World War . Information concerning cement used by the American Expeditionary Forces was furnished by Lt. Col. H. S. Spackman and Major E. C. Eckel , U. S. R. , who had charge of practically all matters concerning cement used by the A. E. F. The cement used by the A. E. F. came from the following sources : 42,000 tons was French , Swiss , and Spanish cements ; 120,000 tons was English cement ; 55,000 tons made in plants operated by the A.E.F .; 500 tons ( Not over) from America . Deterioration was most marked in cement from the first source .

Jun 1, 1922

By Kenneth G. Broadhead

Four applications of radiotracer techniques in metallurgical research are described: (1) In electrowinning tungsten from scheelite, molybdenum 99 was used to detemine the molybdenum concentration of the fused alkali-phosphate bath and the electrowon tungsten; (2) an attempt to detemine the solubility of tagged ceric oxide in molten CeF3-BaF2-LiF was unsuccessful, but a high rate of cerium ion exchange was observed; (3) iron 59 was added to cerium during casting and used to follow the migration of iron during solid state electrolysis; (4) radiotracers were used in developing special analytical techniques applicable to high-purity rare-earth metals produced by molten salt electrolysis.

Jan 1, 1963

By William E. Wallace, S. J. Page, B. L. Razzaboni, C. A. Hill, Pamela Mike, P. Bolsaitis, M. J. Keane, Val Vallyathan

"Respirable quartz cytotoxicity, as measured by erythrocyte hemolysis and pulmonary macrophage release of lactate dehydrogenase in vitro, is neutralized by boiling in water in glass test tubes for 10 to 40 minutes. The cytotoxicity is reduced to near zero by boiling l to IO mg quartz per milliliter water. For greater concentrations of quartz in water the hemolytic potential after 40 minutes of boiling approaches that of native quartz. Replacing the medium with fresh water midway through boiling results in full detoxification through 20 mg quartz per milliliter water. Pre-boiling the medium with silica reduces the detoxification effect. Detoxification persists after mild drying at l 10°C for 8 hours, and persists after three days of resuspension in water at room temperature.INTRODCJCTIONResearch underway to determine interactions of quartz and other mineral dust surfaces with pulmonary fluids and alveolar macrophages in culture led to the observation that when dusts were autoclaved in aqueous suspension, their cytotoxic effects on macrophages were suppressed, in some cases fully and even after several days incubation with the cells. This finding was in direct contradiction to earlier results from both short term macrophage lysosmal enzyme release assays, as well as longer term cytotoxicity assays from macrophages in culture; in those studies, dusts were steam autoclaved at 121°C with no liquid water but with steam present. 1.2 However detoxification under boiling conditions has been reported in other research. 3 It was decided to use the hemolysis assay to further investigate these findings, because of its sensitivity simplicity and cost.RESCULTS AND DISCCISSIONRespirable quartz dust used in this study was taken from a stock of crystalline silica, Min-U-Sil; obtained from Pennsylvania Sand Glass Corporation, fractionated in air with a particle classifier. The small size fraction retained for use was 80% less than S micrometer particle diameter, with an area equivalent median diameter of 1.24 micrometers as estimated by automated image analysis. The silica was at least 98.S mass percent silica as determined by X-ray energy spectrometric analysis; and the crystalline form was alpha-quartz as determined by X-ray diffraction. It's specific surface area was 3.97 square meters per gram as determined by nitrogen adsorption isotherm methods. I"

Jan 1, 1990

By BUREAU OF MINES

Atentative Draft of a standard smoke abatement ordinance has been prepared by a joint committee made up of representatives of the American Society of Heating and Ventilating Engineers, the Stoler Mamufacturers Association, the American Civic association, and the Fuels Division of the American Society of Mechanical Engineers. The Committee is desirous of obtaining helpful criticism and suggestions about this ordinance, which should be mailed to the chairman, Dr. O. P. Hooi, Bureau of lines, ashington, D. C. Te personnel of the committee is as follows: Dr. O. P. Hood, chairman, and Henry Kreisinger, representing the Fuels Division of the American Society of Mechanical Engineers; P. J. Dougherty, representing the American Society of Heating and Ventilating Engineers; Lloyd R. Stowe, representing the Stoker Mam- facturers Association; Everett L. Hillard, representing the American Civic Ascociation; and Osborn Monnett and Harry 3. Meller, members at large.

Mar 1, 1930

By G. R. Palmer

The Bureau of mines evaluated the elution of uranyl carbonate from a strong base resin with a mixed carbonate eluant in a fluidized system. The system consisted of a multiple-compartment ion-exchange (MCIX) elution column with a continuous flow of solution, except for short periods when the resin increments were withdrawn. The exchange of uranyl carbonate from the mill-loaded strong base resin with an eluant composed of 1.0 [M] NaaCOs plus 1.0 [M] NH4HCO3 was studied. The effects of solution flow rate, aqueous-to-resin flow ratio, column diameter, compartment height, initial resin concentration, and column length were examined. The experimental data indicate that for the eluant examined, a resin residence time of 240 minutes is necessary to attain 90-percent elution efficiency. Also provided is a technique for sizing an elution MCIX column form pilot plant experimental data.

Jan 1, 1979

By G. V. Sullivan

The Bureau of Mines conducted preliminary beneficiation studies of a gold-bearing graphitic schist from Blue Hill, Tallapoosa County, Ala. The average analysis of the material was 0.08 oz/ton gold. Tabling of minus 35-mesh material recovered 83 to 94 percent of the gold at grades of 6.925 to 2.165 oz/ton, respectively. A combination of jigging and tabling resulted in a concentrate assaying 24.3 oz/ton gold and contained 87 percent of the total gold. Treatment of the material by jigging, tabling, and amalgamation recovered 86.5 percent of the gold.

Jan 1, 1969

By J. B. Newson

This is one of a series of circulars dealing with mining methods, practices, and costs. It describes the method of sinking a shaft 60 inches in diameter with a shot drill, as employed at the Idaho Maryland mine, Grass Valley, Calif. The operation involved a great deal of experimentation in applying the shot-drill method to large bore drilling, overcoming mechanical and other difficulties which developed during sinking, and developing operating technique. Under such circumstances, costs are obviously higher than they would be after the pioneer work has been done, but even so, these actually obtained compare favorably with costs of sinking by more conventional methods. ACKNOWLEDGMENTS The authors are indebted to Mr. Errol McBoyle, president of the Idaho Maryland Mining Co., not only for his cooperation and advice during the sinking of this experimental shaft, but for permission to prepare this article for publication with the inclusion of cost data.

Jan 1, 1936

By R. V. Ramani, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways (National Academy ofSciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Mar 1, 1989

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground' mine airways (National Academy of Sciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Aug 31, 1989

By E. J. Kloos

The Bureau of Mines devised a new machine-test method for measuring carbon dioxide inspired by a wearer of self-contained breathing apparatus. The new method compares favorably in speed and precision with standard man-tests in which the apparatus is tested while actually worn, and is scheduled for use in future approval tests for facepiece carbon dioxide 'measurements. However, man-tests will still be used to measure the efficiency of the carbon dioxide sorbent materials in closed-circuit breathing apparatus.

Jan 1, 1966

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By D. W. Butner

As a part of the Bureau of Mines program for the discovery and development of critical and essential mineral deposits, the Darwin district, Inyo County, Calif., was chosen for investigation as a possible source of, tungsten ore. Two properties were active in the district at the time. One was producing tungsten concentrate and the other was preparing to produce tungsten concentrate as a byproduct in the milling of lead-zinc ore. The objective of the project set up by the Bureau was to investigate promising areas and to sample, thoroughly those which preliminary inspection indicated contained tungsten ore. Work was begun November 17) 1941, and completed January 19, 1942. In the course of the project, 18 localities were inspected and 9 were sampled. The following pages brief the history, note the location, and outline the physical features and geology of the district. The work performed by the Bureau of Mines is described and supplemented with assay maps.

Jan 1, 1949

By Bill M. Stewart

To decrease the potential for fine coal waste slurry impoundment failures, the Bureau of Mines investigated a new disposal technique. The fine coal waste slurry is rapidly thickened (i.e., dewatered) and deposited on a slightly sloping surface. To accomplish rapid dewatering, a chemical flocculation system using polymers was developed to treat the fine coal waste slurry stream. The fine solids formed flocs, settled from suspension, and rapidly released excess water. During the last 5 days of the field test, slurry flowing at rates from 498 to 675 gal/min with a specific gravity range of 1.15 to 1.33 was successfully treated and dewatered. During this period, untreated slurry had an average moisture content of 227.4 pct (30.7 wt pct solids). The effectiveness of the dewatering system was determined by monitoring the moisture content of the deposited waste with respect to time. Sixty-five hours after ending the field test the average moisture content was 54.9 pct (64.5 wt pct solids); 68 days after the field test the average moisture content was 28.8 pct (78.0 wt pct solids).

Jan 1, 1986