Search Documents

By James Rowland, Isaac Zlochower, Richard Mainiero, Michael Sapko

The National Institute for Occupational Safety and Health (NIOSH) carried out exploratory laboratoryscale studies to identify factors that may contribute to nitrogen oxides (NOx) production associated with non-ideal detonation of blasting agents. Explosive admixture with drill cuttings, loss of fuel oil in ammonium nitrate and fuel oil (ANFO) from wicking, ammonium nitrate dissolution with water, degree of explosive confinement, ANFO density, and critical diameter were identified as contributing factors to increased NOx production under the laboratory test conditions. Experiments were also conducted to examine the effectiveness of various additives in reducing the NOx production from ANFO, emulsion, and ANFO/emulsion blends. Aluminum powder, coal dust, urea, and excess fuel oil in ANFO formulations were tested and were found to reduce both the nitric oxide (NO) and nitrogen dioxide (NO2) production. Fumes measurements were obtained in the NIOSH underground closed chamber from the detonation of 4.5-kg (10 lbs) charges in schedule 80 seamless steel pipe and from detonations in light weight galvanized steel stove pipe. Some exploratory tests were also conducted with 0.8-kg (1.8 lbs) charges of pulverized ANFO initiated with 0.08-kg (0.18 lbs), 50/50 (Pentolite) boosters (in the NIOSH 12-ft (3.7-m) diameter steel sphere) to measure the degree of fumes production associated with post-detonation oxidation. Ammonium nitrate, emulsion and Pentolite boosters were also detonated in an oxygen-poor environment.

By C. Travis Anderson

 The general conclusion of earlier investigators was that the action of sulfur dioxide on manganese oxides of Cuyuna ores was not sufficiently pre- ferential to be attractive as the basis for a commercial process. Bradley4/ and his coworkers discarded it for leaching with boiling ammonium sulfate solution, and Sweet5/ used a baking operation to render the iron insoluble. These results were confirmed by the early tests in the present investigation, which were made on brown ores (Sagamore), using acid additions, because at that time the Technologic Committee on Manganese held the opinion that these ores constituted the major available reserve in the Cuyuna district. However, when it appeared that the black ores, or the formation in which they occur, were a possible source of a large tonnage of manganese, the use of sulfur dioxide and sulfuric acid leaching was again reviewed, and a satis- factorily preferential action on the manganese was found. It was originally thought that the use of sulfuric acid ahead of, or at least with, the sulfur dioxide simplified the process, particularly by preventing formation of dithionates. Removal of the phosphorus from the solution by neutralization with lime or fresh ore was suggested. The tests recorded in this report indicate that it is not practicable to use enough acid to prevent formation of dithionate and that the value of excess sulfuric acid is doubtful, particularly in regard to satisfactory manganese:phosphorus and manganese:iron ratios.

Jul 1, 1942

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of-combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were conducted in a 1 80 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.13, and 0.06 m/s were determined at 30.60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

By A. S. Griffiths, J. E. Evans

Noise processing experiments with ELF (3 to 300 Hz) atmospheric noise and signals in the 40 to 80 Hz range are described. The primary purpose of the experiments was to record and analyze wideband ELF noise in order to design the noise processing portion of a receiver which minimizes the required transmitter power. The application of appropriate theory and extensive simulations led to a noise processor which consists of the following functions: (1) a compensating (or whitening) filter, (2) a prenotch filter clipper, (3) notch filters at frequencies of manmade interference (e. g., power lines), (4) a post-notch filter clipper, and (5) a phase-coherent linear matched filter. The nonlinear processing provides considerable gain relative to a linear receiver (i. e. , a receiver consisting only of a matched filter and appropriate whitening filters). It is convenient to measure sys tem performance in terms of an "effective noise level" which is equal to twice the received signal energy divided by the signal to noise ratio at the matched filter output. For example, the highest effective noise levels observed at 45 Hz with the nonlinear processor were about -134, -131 and -137 dB wrt 1 amp/m [Hz] using Saipan, Malta and Norway data, respectively, compared to 1 percent exceedance levels of effective noise for the linear receiver of about -115, 115 and -130 dB wrt 1 amp/m [Hz] respectively.

Jan 1, 1973

By N. A. Caspero, W. E. Eckard, W. T. Wertman

A thermal oil-recovery experiment was conducted in the Venango First sand, Goodwill Hill oilfield, Warren County, Pa., about 10 miles northeast of Titusville. The Quaker State Oil Refining Corp., Bradford, Pa., performed the experiment with assistance from Sinclair Research, Inc., Tulsa, Okla., and the Federal Bureau of Mines. The Goodwill Hill field was discovered in 1885. Primary-production oper- ations continued until 1930 when an air-gas injection project, which is still in operation, was started. At the location of the combustion experiment, the reservoir is 400 feet deep and 30 feet thick, with wide permeability and porosity variations. The crude oil is typical Pennsylvania Grade paraffin- base oil with a gravity of 43.9° API and a viscosity of 4.55 cp at 60° F. The well pattern for the experiment consisted of 5 producing wells, enclosing an area of 1.28 acres, and a central ignition-injection well. An air-natural gas mixture was ignited in the ignition well on July 29, 1961. Ignition was followed by injection of air and natural gas at various rates. The experiment was suspended January 5, 1962, when it became evident that economic oil production could not be achieved. There was no conclusive evidence that self-sustained combustion was achieved or that combustion increased oil and water production. A slight increase in liquid production was attributed to stripping action caused by the air-injection rates, which were higher than those normally used during air-gas injection.

Dec 1, 1963

By J. J. Rutledge, C. A. Herbert

In 1916 the Bureau of Mines, the Illinois Geological Survey, and the University of Illinois, working under a cooperative agreement, began an investigation of the subsidence of the surface above coal- mining operations. Four widely separated places where mining was in progress were selected as observation stations-one in the northern Illinois longwall coal field, one in the central Illinois coal field where the room-and- pillar panel system of mining was being used, and two in the thick coal of southern Illinois where the room-and-pillar panel system of mining was employed. These four points of mining activity gave a rather wide opportunity for observing subsidence when different mining methods were used. The four places selected for investigation of surface subsidence due to coal mining have been designated as follows: 1. A, in the northern Illinois longwall coal field, where the coal company has been operating coal mines for 30 years and where long- wall advancing is the only method of mining. 2. B, in Perry County, where panel room-and-pillar mining of a thick seam of coal is in progress and where mining operations have been carried on about 40 years. 3. C, in Macoupin County, where the coal company has been min- ing coal by the panel room-and-pillar method for about 15 years. 4. D, in Franklin County, where the coal company has been mining coal for 10 years by the panel room-and-pillar method.

Jan 1, 1927

By C. B. Manula, R. L. Sanford, R. A. Rivell

A generalized flow diagram is presented in Figure 1, which shows the relationship of major model functions. This chart does not necessarily represent the anatomy of the computer program, but is designed to illustrate the informational interchange between major model functions. The related flow-charts-and computer program are listed in Parts I and II, Appendix A, respectively. Mine Car Stations The mine car stations are the activity centers for the model. The locomotive logic structure is designed to provide these stations with adequate cars and to clear them of car buildup. The model is designed to simulate a three stage haulage situation which suggests the need to differentiate station levels by type numbers. These are: a) TYPE 1 stations - mine cars are loaded here; b) TYPE 2 stations - intermediate stop and storage for mine cars; c) TYPE 3 stations - all mine cars that are stored here leave mine; and d) TYPE 4 stations - mine portal. TYPES 1, 2, and 3 have all loaded cars assigned to an ascending TYPE as their next destination. In input, if single stage haulage is designated, TYPES 1 and 3 do not exist, and if two stage haulage is called for, TYPES 2 and 3 are absent. A motor is not permitted to exchange cars between stations of the same type. Station Status Update. One major model function is to continuously evaluate the status of each mine car station. The major evaluations

Jan 1, 1974

By Kenneth G. Skinner

The rapid growth of the metallurgical, chemical, and allied industries on the Pacific coast just prior to and during the war caused a sudden increase in the demand for refractories, which was the immediate cause of a revival in interest in refractory clays available on the Pacific coast, particularly in the Pacific Northwest. Population increases and shortage of shipping facilities caused an increase in the amount of various ceramic materials and products used and produced on the Pacific coast, with accompanying demand for information regarding sources of clay. In an effort to supply part of this information, the Bureau of Mines, in cooperation with the College of Mines, University of Washington, started a program in 1944 to test the refractory and other properties of clays from seven Pacific Northwest deposits that had been drilled and sampled as part of the Bureau of Mines alumina from clay investigation. Figure 1 shows the location of these deposits.

Jan 1, 1949

By Sumner M. Anderson

THE importance of the mineral industries of the Latin American area in 1964 may be evaluated in respect to a number of points of reference, a few of which are measurable and appropriate for examination. With regard to the region's contribution to total world production, it accounted for total 1964 world output of natural nitrates (from Chile), and about 97 percent of the optical and electrical grades of quartz crystal (from Brazil). The region supplied over 20 percent of world output of 7 other mineral commodities and accounted for 4 percent or more of world output of 19 other mineral products. Among major commodities, the area, occupying 15 percent of the earth's land surface, supplied within 3 percent of that proportion of the world's output of copper, lead, tin, zinc, barite, and crude petroleum. Incomplete compilation of production data, particularly that of nonmetallic minerals, precludes production estimates on some items for the area ass whole, and therefore the importance of Latin America as a world producer of some additional commodities may not be clearly assessed. For example, most of the countries of the area collect only incomplete data or no data at all on the production of clays and other ceramic materials, sand and gravel, dimension and crushed stone, lime, ornamental and precious stones, perlite, vermiculite, carbon black, coal tar products, and petrochemicals. In the case of many countries of the area, the value of production of one or more of these commodities greatly exceeded that of other mineral industry products that are carefully reported.

Jan 1, 1966

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Downstream processing of these mineral fuels to petrochemicals and fertilizers is a major investment opportunity. In 1991, the 15 countries that constituted the region accounted for 26 % of world crude petroleum output, 15.3 % of world natural gas plant liquid production, and 4.5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Production of these mineral fuels all declined from that of 1990 owing to the Persian Gulf War, during which output from Kuwait and Iraq either ceased owing to war damage, or was embargoed. Prior to the war, Iraq and Kuwait were the fourth and fifth largest world producers of crude petroleum, respectively. In the war, virtually all of Kuwait's production and transport facilities were destroyed or damaged. Iraq's output was embargoed from export, with only domestic sales taking place. The embargo also affected Jordan, both in terms of transshipment of materials through it to Iraq and in exports of phosphate and potash. Shipments of crude petroleum by pipeline from Iraq through Saudi Arabia and Turkey and by vessel through the Persian Gulf were terminated. However, the loss in production from Iraq and Kuwait was made up by accelerated output from other Middle East and world producers. Saudi Arabia, in particular, with its excess production capacity, accounted for the largest portion, increasing crude petroleum output by 27 % to almost 3 billion barrels.

Jan 1, 1993

By Linneas W. Laage

Coal production from underground coal mines has been important to the development of the industrial economy of the United States. Environmental problems have developed from some abandoned operations. These problems include: mine and refuse pile drainage, subsidence, unsafe mine openings and to a lesser extent mine gases, slope stabilities, mine and refuse pile fires and abandoned equipment and structures. Field investigations in three eastern coal mining districts, two in Ohio and one in Illinois, were performed to document the mine closure procedures used and subsequent problems that developed. The purpose was to identify, evaluate, and rank the seriousness of these problems. Based upon this evaluation, the undesirable present day situations could have been avoided or at least minimized by varying certain mining practices or mine closure procedures. It was found that federal regulations address all of these problems during the pre mining, active mining and post mining phases except for abandoned equipment which is the least threatening problem category. Ideally current practice would prevent future problems. However, the extensive and complicated nature of the legislation, environment and mining practices will necessitate adjustments to the law. The investigator recommends the following: 1) Goal oriented legislation encouraging complete resource extraction, standardization and compilation of mining generated hydrological data, periodic review of the coal mining regulations, and improved communication and cooperation between coal interests, regulators and the public. 2) Permitting effluent limitations to accurately reflect natural conditions. 3) Solidly back filling shafts and individual assessment of sealing or capping requirements. 4) Installing shaft vent pipes into the fill material to intercept and vent methane.

Jan 1, 1982

By J. J. Hoeppner

Lignite samples were collected so as to be widely representative of the extensive deposits in the western north-central area. These were carbonized at temperatures ranging from 450° to 550° C., according, to a standardized procedure. In general, product yields varied; extremes obtained on selected samples show char recoveries on the moisture- and ash-free basis as 56.7 percent for slack lignite or "leonardite" to 80.8 percent for a concentrate of the fusain component from a typical face sample; normal lignite samples averaged approximately 70 percent. Tar-plus-light-oil yields ranged from 3.3 percent for the fusain concentrate to 11.0 percent for a normal sample, averaging approximately 8 percent; gas recoveries varied more widely both in yield and in composition, ranging, from 10.0 percent to 27.7 percent, the latter being from leonardite and quite high in carbon dioxide. Sampling was conducted with the view of representing, as nearly as possible, all beds delineated by Brant (2);4/ many are necessarily missing since collection was confined largely to worked deposits. Data presented in this report indicate a general uniformity of North-Central lignite in respect to low-temperature carbonization, with a few possible exceptions of a local nature. When processed according to the indicated conditions, maximum tar yield may be realized with minimum loss of recoverable heating value of the original coal. Natural weathering of lignite, however, does affect tar yield adversely and should be held to a practical minimum in any commercial operation.

Jan 1, 1956

By A. W. Fahrenwald

The purpose of screening is to separate a crushed or natural product into one or more products in which size of grain is constant, or within certain size limits. The ore dresser finds need for this operation in the laboratory, in the study of ore-dressing processes, and for various purposes in the plants. In the plant, for example, screens are employed in closed circuit with crushing devices such as rolls, and sometimes are used in closed circuit with ball mills. Screens are generally used to prepare jig feed where a sized feed is wanted. For any given sieve opening there is in any feed a certain percentage of grains that will pass through the sieve meshes only with difficulty and under favorable conditions. For example, cylindrical grains of length greater than the maximum dimension of the sieve mesh and of diameter less than the sieve opening pass the sieve only when the long axis of the grain is normal or nearly normal to the sieve. Whether such grains should actually be in the through's or the oversize of a screening operation--considered from the point of view of the subsequent treatment of the grains--can not be said. The grains that pass the sieve opening in a screening process only under-favorable conditions have been named "difficult" grains by R. K. Warner.4 In many ore-dressing flow-sheets it probably matters little whether these difficult grains show up in the screen through's or oversize. The main objection to them is that they are sieve-blinding.

Jan 1, 1929

By R. Blickensderfer

Test equipment that simulated frictional impacts between coal-cutter bits and mineral inclusions at a coal face during operation of a continuous coal mining machine was used by the Bureau of Mines in the laboratory to study the incendivity of impacts between various rocks, metals, and hard-metal alloys in an explosive mixture of air-7 pct natural gas. Quartzitic sandstone was found to be the most incendive of several rocks tested. Limestone concretions from a coal seam, known locally as "sulfur balls," sparked furiously but were not incendive. Among the metals tested, the type of steel used in commercial coal-cutter tools was the most incendive material tested. A l7-4PH stainless steel was less incendive and appears to be the most promising high-strength steel alloy, reasonably economical, for use in coal-cutter bits. Some hard-metal alloys, primarily titanium and zirconium diboride composites, were also evaluated as possible replacements for the conventional cobalt-bonded tungsten carbide used in the tip of coal-cutter bits. The metal-bonded diborides were generally less inc endive but more brittle than the conventional tungsten carbide. Carbonitride coatings on tool bits were also tested but found to have no advantage. The source of ignition during frictional impact between metal and rock was studied. Immediately after impact, a yellow flash was observed and a smear of metal near its melting point occurred on the rock. This hotspot on the rock, rather than the yellow flash or sparks or metal fragments, was observed to be the cause of the ignition.

Jan 1, 1974

By J. M. Stuve

Low temperature and high-temperature calorimetric measurements were made by the Federal Bureau of Mines on high-purity samples of Re02(s) and Re03(s) to determine heat capacities and enthalpies. The temperature range of heat capacity measurements was 5 to 310 K for Re02 and 8 to 309 K for Re03. High-temperature enthalpy measurements alone were determined for pure Re207(s,1). The derived standard entropies are S°298 = 11.43±0.01 cal/deg mole for Re02(s) and S298 = 16.55±0.02 cal/deg mole for Re03(s). High-temperature enthalpy equations expressed in calories per mole are as follows: Re02 (s) , H-H298.15 = 16.002T + 1.600 X 10-3T2 + 3.522 X 105T-1 - 6,095 (298 to 1,400 K); Re03 (s) , H-H298.15 = 20.293T + 3.238 X 10-3T2 + 3.950 X 105 T-1 - 7,664 (298 to 1,000 K); Re207 (s) , H-H298.15 = 38.437T + 10.309 X 10-3T2 + 4.315 X 105 T-1 - 13,824 (298 to 413 K); Re207 (s) , H-H298.15 = 30.181 + 17.713 X 10-3T2 - 10,612 (413 to 600 K) ; Re207 (1) , H-H298.19 = 66.101T - 10,092 (600 to 700 K). Gibbs energy of formation (?Gf°) data and related functions over the temperature ranges investigated are tabulated for the three oxides.

Jan 1, 1976

By A. J. Barry

Two methods of testing anchorages of headed expansion-type mine roof bolts were investigated by the Federal Bureau of Mines to determine whether they are acceptable for general use. In both methods a load was applied to a tightened bolt with a hydraulic jack. A total of 80 tests, 40 using each method, was conducted in 4 test areas in 3 commercial coal mines. Electric resistance strain gages were used in all tests to indicate true bolt load as the bolt was tightened and when an additional load was applied with the hydraulic jack. The results indicate that: 1. The relationship between the true bolt load and the jack load will vary according to the test method until the two loads become equal. The bolt load-jack load relationship below this point can be determined only with strain gages. 2. The point at which the two loads become equal can be estimated by noting the load when the hardened washer becomes loose in one method, and when the bearing plate becomes loose from the roof in the other. It also can be approximated for either method of testing by noting the load when the first abrupt change in the slope of the jack load-bolt displacement curve occurs. 3. The anchorage characteristics of the test bolt can be determined from the data obtained from either method by examining the slope of the jack load-bolt displacement curve above the point at which the true bolt load is equal to the jack load.

Jan 1, 1960

By Martin H. Stanczyk

Two methods of recovering zinc from zinc ammonia complex solutions were investigated. One method studied was distillation of the ammonia from the solutions to recover a basic zinc sulfate, which after calcining to zinc oxide was reduced to metallic zinc using hydrogen at 900° C. The second method tested was electrolysis. The tests were made of synthetic and leach solutions analyzing about 80, 100, and 115 gpl (grams per liter) of Zn, NH3, and SO4, respectively. The leach solutions were prepared by oxidation leaching of a sphalerite flotation concentrate, assaying 55 pct zinc at elevated temperature and pressure. The distillation method recovered about 98 pct of the zinc in a product analyzing 97 pct zinc. Ammonia losses incurred during the leaching and distillation operations were about 0.1 lb per lb (pound per pound) of metallic zinc produced. Electrolysis of the solutions at a cathode current density of 25 amp per sq ft (ampere per square foot) yielded zinc deposits assaying in excess of 99.9 pct zinc. About 1.5 kwhr (kilowatt-hour) of power were consumed per pound of zinc deposited; the current efficiency was 72 pct. Other electrodeposition tests revealed that small amounts of ferric iron in the cell liquor were deleterious to electrolysis unless about 5 lb of glue per ton of zinc were present in the electrolyte. The use of glue and vigorous agitation of the electrolyte gave smooth zinc deposits from solutions containing as much as 0.1 gpl iron.

Jan 1, 1962

By Lucia Kuizon

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines studied the Diamond Peak area comprising 183,000 acres in the Challis and Targhee National Forests in order to evaluate its identified mineral resources. More than 3,000 mining claims were located in three mining districts between the years 1882 and 1986. Approximately 230 mining claims in and the 150 claims adjacent to the study area were current in 1986, when Bureau of Land Management mining records were researched for this study. A total of 1,270 samples were collected from these sites (30 were for alluvial placer). Results of the investigation help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Lead-, silver-, zinc-, copper-, and gold-bearing minerals occur as veins and replacement bodies in shear and fault zones in Precambrian and Paleozoic calcareous Sedimentary rocks that have been complexly folded and faulted. Total production from the three mining districts in the study area was more than 150,000 tons of ore between 1901 and 1982. Approximately 11,600 tons of subeconomic resources consisting of lead, silver, zinc and copper were identified within the area. Over 37,500 tons of lead and zinc subeconomic resources were identified just outside the area. In addition, lead-, silver-, and zinc-mineral resources were identified at 4 mines within 2 miles of the study area. Iron mineral resources were also identified just outside the area.

Jan 1, 1991

A list of permissible mine equipment approved by the Bureau of Mines before January 1, 1937, was published in Bureau of Mines Information Circular 6942.3/ Information Circular 7007,4/ published as a supplement thereto, listed equipment approved. Burin', the calendar year 1937. The present list includes most of the material liven in these two publications, as well as approvals that have been issued up to January l, 1940. Some equipment formerly listed has been omitted because it has become obsolete or is no longer actively marketed. The list now includes electrically-operated air compressors, coal drills, loading machines and conveyors, mining machine, mine ones, rock-dusting machines, room hoists, storage-battery gathering and haulage locomotives and storage-battery power trucks, mine telephones, junction boxes, electric cap lamps, flame safety lamps, electric hand and trip lamps, electric flood lens, flashlights, methane detectors, and single and multiple-shot blasting units. The appendix at the end of this circular lists trailing, cables that have passed tests prescribed by Schedule 2D. When equipment passes the inspections and tests prescribed by the United Status Department of the interior, Bureau of Mines, in published "schedules" or standards, it is formally approved as "permissible" for use in gassy mines, and the manufacturer is then permitted to mark it with an approval plate that identifies it as having been approved by the Bureau. The inspections and tests are designed to insure that each equipment satisfies the minimum requirements for safety in use. The Bureau's purpose in investigating equipment of this type and listing that

Jan 1, 1940

By G. L. Neumann

In October 1949 the College Park Branch of the Mining Division instituted a survey of the New England pegmatites. Many of the New England pegmatite deposits were superficially examined, and the Bumpus quarry in Albany, Oxford County, Maine (see fig. 1), was selected for a diamond-drill exploratory-development project to supply information for developing more economical mining methods and no increasing production of beryl and other scarce minerals associated with pegmatitic intrusives. The Bumpus quarry has been mined intermittently by three operators since it was opened in 1927. At the time of drilling, the vein or dike (see figs. 2 and 3) had been mined to a depth of 60 feet for a strike length of 280 feet. The dike averages 40 feet in thickness and dips 50 degrees southeast. The Bureau of Mines drilled seven diamond-drill holes between September 27 and November 27, 1950. These holes showed that the dike persists for at least 350 feet to the east and probably 200 foot to the west of the present excavation. The drilling also indicated that the dip, as exposed at the surface, continued unchanged at 500 to a depth of at least 50 foot below the pit. The dike was not delineated, although it fingered out as pegmatite interbanded with Granite, diorite, and gneiss in diamond-drill hole B-4, approximately 250 feet west of the pit. Further drilling will be necessary to find the extent of this pegmatite dike and to determine the safest and most economic mining system.

Jan 1, 1952