Search Documents

By W. P. Yant

The hazard to health from contamination of air by a noxious gas depends not only on the potential harmful response attending exposure., but also on the warning properties, which in effect may be termed the "accompanying warning response," This warning may be manifested as an odor, taste, irritation of the eyes, nose, or throat, or perhaps headache, vertigo,, or nausea. These manifestations may be painful and even slightly harmful, but to a much lesser degree than the primary injury of exposure. The warning response mitigates hazards directly in proportion to the degree of intolerability which -accompanies injurious exposure, and accordingly its absence augments hazards. This accounts for the fact that the actual health hazards from a nonodorous or non-irritating gas or vapor of comparatively low toxicity sometimes equal or exceed the hazard from a considerably more toxic substance, but one which possesses a marked odor or produces eye, nose, or throat irritation in advance of harmful exposure. When a substance lacks the properties for giving warning, it is often possible to impart them by the addition of a small amount of another substance which has an exceedingly high warning intensity. The vapors of this substance, commonly termed a "warning agent" or "tracer gas," escape and mingle with the gas or vapor which lacks warning properties and thereby apprises persons of the latter's presence. The amount of the warning agent added is that which will give adequate warning in advance of serious physiological harm from the dangerous gas or vapor.

Jan 1, 1930

By James R. McVey

A new method for measuring deformations of rock surfaces in underground excavations has been suggested by Dr. James Powell of Brookhaven National Laboratories (BNL) and subsequently developed and successfully demonstrated in a mining environment by the Federal Bureau of Mines, Spokane Mining Research Center (SMRC) and Brookhaven National Laboratories. The system uses 35-mm photography of targets strategically located on surfaces of interest, such as across the roof and on the sides of a mine drift or tunnel. The optimum tar-get, as determined in this investigation, consists of a white ?X? made with 1/8-inch-wide reflective tape on a black 6-inch square. Photographs, taken in pairs from two separated camera positions and at regular time intervals, were analyzed at the Bureau by hand and at Brookhaven National Laboratories using techniques and equipment similar to those used in cloud chamber film analysis. Test results show that deformation-measurement accuracies of better than ±0.020 inch in a drift that is 20 feet wide can be expected. This degree of accuracy, plus providing displacement data in the X, Y, and Z directions (rather than the one direction formerly possible), makes this a noteworthy and useful tool for industry as well as for mining research.

Jan 1, 1974

By T. M. Romslo

"INTRODUCTION This report presents factual data obtained by the Bureau of Mines in the course of an investigation of the Antler mine in the Cedar Valley mining district, Mohave County, Ariz.The Antler property was first examined by Thomas L. Chapman, mining engineer, Bureau of Mines, on December 18, 1943, and January 28, 1944. In June 1945, A. H. Wadsworth, Jr., and R. L. Griggs, geologists, Federal Geo¬logical Survey, examined the Antler mine and several other mines in the district. Both Chapman and Wadsworth recommended diamond drilling of the Antler property to determine the character and extent of ore deposition.In October 1946, the surface and underground workings were surveyed by George Huseman, Mining engineer, and T. M. Romslo, project engineer. The following month Eldred. D. Wilson, geologist of the Arizona Bureau of Mines, assisted by the project engineer, mapped the geology. Subsequently trails were built to drilling sites and diamond drilling started January 16, 1947. The project was completed April 25, 1947.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and takes beneficiation tests."

Mar 1, 1948

By Frank A. Peters

With the current renewed interest in advancing the technology for producing alumina from domestic raw materials, revisions of previous cost estimates to provide planning data are urgently needed. Completely new cost estimates on a 1973 basis are included for four alumina-from-clay processes and one alumina-from-anorthosite process. These estimates are based on new or previously calculated material balances, recalculated heat requirements, and new equipment designs. The use of larger and more modern equipment has permitted a significant reduction in labor requirements as well as equipment costs. Chemical prices, labor rates, and utility rates typical of late 1973 are used in these cost estimates. In addition to the revised cost estimates, all 21 previously published alumina evaluations compiled by the Bureau of Mines were updated to show the effect of inflation using an inflation index and late 1973 chemical prices, labor rates, and utility rates.

Jan 1, 1974

By William C. Larson

This Bureau of Mines report discusses uranium in situ leach mining in the United States to acquaint the public with an overview of this emerging mining technology. This report is not intended to be a technical discussion of the subject matter, but rather should be used as a reference source for information on in situ leaching. A list of in situ leaching publications is included as well as engineering data tables for almost all of the active pilot-scale and commercial uranium in situ leaching operators. These tables represent a first attempt at consolidating operational data in one source, on a regional basis. Additional information is given that discusses the current Bureau of Mines uranium in situ leaching research program. Also included is a listing of various State and Federal permitting agencies, and a summary of the current uranium in situ leaching operators. Finally, a glossary of terms has been added, listing some of the more common terms used in uranium in situ leach mining.

Jan 1, 1978

By Hillary W. St. Clair

This report describes a mathematical procedure for analyzing size distribution data by the method of moments. The method was applied to Andreasen's data on a variety of grinding mill products. It was found that the observed size distributions could be represented by gamma and beta distribution functions over a wide range of sizes. A computer program, written in BASIC, is described for calculating moments, distribution parameters, and the weight fraction in any size range.

Jan 1, 1969

By Frank J. Weibelt

In accordance with provisions of the Strategic Minerals Act of 1939, the Bureau of Mines surveyed the chromite occurrences in California. The Seiad Creek deposit afforded excellent opportunity for developing reserves that could be used by the nation in case of critical shortages of the mineral. Subsequently an exploration and development program was undertaken in April 1941, which was concluded in October of the same year. Work included road construction, diamond drilling, drifting and crosscutting, surface trenching, and sampling.

Jan 1, 1949

By Arnold M. Lansche

Domestic Production.-Domestic production of white arsenic, AS,03, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. The Anaconda Company discontinued production of white arsenic in 1965. Arsenic metal was not produced. Consumption and Uses.-Most of the white arsenic produced in 1965 was consumed in manufacturing lead and calcium arsenate insecticides.

Jan 1, 1966

By A. T. Iannacchione

Roof-rock instability in advancing sections of underground coal mines is a major contributing factor to accidents resulting in fatalities and injuries. Such roof-rock conditions can also result in loss of production due to additional cleanup time and increased amounts of reject material. The Bureau of Mines is investigating fundamental geologic factors affecting coal mine roof-rock instability in order to develop techniques to predict zones of potential unstable roof-rock. Two distinct directional trends of unstable shale roof-rock in a mine working the Upper Kittanning Coalbed are delineated: one trend is associated with the sandstone-shale transition zone, the other with a fault system. The unstable shale roof-rock associated with the transition zone, a consequence of differential compaction, is comprised of slickensided roof-rock. Whereas, the unstable shale roof-rock associated with the fault system, a consequence of structural deformation of the strata, is comprised of fault planes. These faults, small in comparison to the sandstone-shale transition zone, are difficult to delineate with a standard drilling program. Trends of the transition zone associated with the sedimentary facies change are projected into unmined portions of the coalbed with the aid of exploration core data.

Jan 1, 1981

By R. P. Bush

The U.S. Bureau of Mines performed Cu exchange capacity (CuEe) tests on Ca and Na mont-morillonites and attapulgite clays. Mathematical models were developed from the data that the CuEe's are derived from for each clay as a function of pH, Cu concentration, and the concentrations of metal ions, which compete with Cu for exchange sites. An analysis was made of the impact of competing ions on Cu losses due to ion exchange. The results show that the CuEC's of clays, and hence Cu losses, are decreased by the presence of competing ions, and that AI and Mg have the largest impact of those cat-ions normally present in Cu leaching solutions.

Jan 1, 2010

By David C. McHuron

The U. S. Bureau of Mines in their continuing research into sealants, selected MBAssociates to design, build, and test equipment and evaluate sealant as to its effectiveness is shale degradation. There were 20,050 sq.ft. of coal mine roof sprayed with a mine sealant and as a result, it has been estimated that the sealant coated roof has from 50% to 95% less roof falls than that roof which was not coated with sealant.

Jan 1, 1980

By C. Ortuglio

The effect of cracking by increasing the free space above the charge on the composition and yields of the volatile products from carbonization of Pittsburgh-bed coal and one industrially used blend from Eastern United States and one from Western United States was investigated with the BM-AGA carbonization apparatus. Increasing the free space above the charge from 1 inch to 3 inches, to 6 inches, and to 9 inches resulted in lower tar yields and increased gas and light oil yields. Anthracene and naphthalene yields were increased; quinoline and benzene insoluble fractions of both the tar and pitch increased considerably with increased free space, although the carbon content of the tars and pitches increased only slightly. Increased cracking, occasioned by the increase in free space, resulted in a decrease in the yields of tar acids, tar bases, neutral oils, olefins, aromatics, and paraffins and naphthenes. Gas composition was relatively constant; hydrogen and methane tended to increase and ethane decrease. Results of the investigation are being used to design a unit to upgrade the volatile products of carbonization by cracking the hot products as they leave the carbonization chamber.

Jan 1, 1970

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: ? Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. ? Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. ? Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

By Scott W. Hazen

This report presents the results of a statistical analysis of a limited amount of sample and assay data from a production panel in an open - pit phosphate mine in the Phosphoria formation in Idaho . A frequency distribution analysis is shown for the assays , sample interval lengths , and products of assay and sample interval length for the millshale , furnace - shale , and main phosphate beds . Correlation techniques were used to show the relationships between assays and sample interval lengths . Within- drill - hole and between - drill - hole correlation were also examined as a means of predicting grade trends in the ore . Simulation methods , utilizing a digital computer , were used to establish assay populations that could be used for estimating grade of ore , cutoff grades , and deposit or bed identification .

Jan 1, 1964

By W. H. Young

THE BITUMINOUS coal and lignite industry declined slightly in 1961, compared with the 1960 figures. All of the major items, production, consumption, average value, exports, and employment, declined. Even the steady upward trend in mechanization failed to materialize; the percentages of total tonnages mechanically loaded and cleaned remained the same as in the preceding year. However, tonnage per man per day increased from 12.83 tons in 1960 to 13.87 tons in 1961, owing partly to the increased tonnage produced by continuous mining machines. Also, the percentage of total production mined by stripping and by augers increased slightly. Production.-The output of bituminous coal and lignite in the United States in 1961-403 million tons-was 3 percent less than the 416 million tons produced in 1960. Production was retarded in 1961, owing largely to the business recession and reduced exports.

Jan 1, 1962

By Robert T. Beckman

The results of a preliminary investigation of compressive strength versus length-diameter (L/D) ratios of potash specimens and the statistical treatment of the data are summarized in this report. The purpose of the study was to evaluate a laboratory method for obtaining estimates of the strength of potash pillars during robbing operations. The specific objectives of this preliminary investigation were to test the method and the reliability (confidence limits) of the data, and to determine the number of additional specimens necessary for given confidence limits. The specimens were taken from three sites at two mines in New Mexico. The statistical analyses included the determination of the confidence limits for the data and the number of additional specimens necessary to obtain confidence limits of ±500 and 100 psi. The testing method was found acceptable, and estimates of the comprehensive strength, within 1500 psi, could be obtained by testing about 110 additional specimens from the three sites. The compressive strength of the specimens tested fits an empirical equation of the type

Dec 1, 1963

ESTABLISHMENT of an effective inspection system has been held essen¬tial to any international agreement that may be designed primarily to curb the testing of nuclear weapons. A number of reports and papers already have described basic inspection concepts and appraised various pro¬cedures, techniques, and methods as to their probable effectiveness in detecting and identifying violations under such agreement. This report results from a study of only one part of the contemplated inspection system, specifically the final phases embracing onsite investigations and mine examination techniques. The results and reports of earlier work were reviewed in detail, and subjects that were found to have been exhaus¬tively evaluated are recognized by reference and not redescribed here. In other instances, previously described techniques, methods, and clues were revaluated to define more clearly their practical value to the final objective of an onsite inspection. Previous documentation does not refer to a number of subjects, techniques, tools, clues, and methods considered by the study; this report treats these in detail, even though when applied singly or collectively their practical value may be questionable.

Jan 1, 1962

By F. S. LOTT, I. S. CULVER

The number of petroleum refineries in the United States decreased during 1948 from 390 to 375, continuing the trend to fewer units of larger individual capacity that has persisted since the peak in number of plants was recorded on January 1 , 1936. Large - scale construction of new processing facilities continued through 1948 with a resultant gain in daily crude-oil throughput capacity of installed equipment from 6,034,252 barrels on January 1 , 1948 to 6,438,995 barrels on January 1 , 1949. The capacity of the average refinery to process crude oil therefore increased during 1948 from 15,472 barrels daily to 17,171 . The principal areas of expansion of facilities were the strategic seaboard districts of the Texas and Louisiana Gulf Coast and the East Coast , and the important Indiana , Illinois , Kentucky, etc. , district that supplies markets in the upper Middle West region . These four districts accounted for 79 percent of the total new capacity added in the United States in 1948. The relatively small petroleum- refining industry of the Other Rocky Mountain district experienced a vigorous expansion in 1948 that will continue during 1949 . Capacity building on January 1, 1949 , amounting to 341,500 barrels daily, was 25,750 barrels lower than the comparable total on January 1 , 1948, but was the second highest on record . New construction was heavily concentrated in the Texas Gulf, East Coast , and Indiana -Illinois

Sep 1, 1949

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974