Search Documents

By R. G. Meara, O&apos

The land-pebble district of Florida, which in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of Sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of limey or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the rushing and formerly lost supplied the feed.

Jan 1, 1931

By Michael J. Magyar

The Federal Bureau of Mines has developed a hydrametallurgical method to recover aluminum, aluminum oxide, and fluxing salts from aluminum salt slags. The slag is leached with water at room temperature to produce a saturated brine slurry. Screening of the slurry yields an aluminum-rich fraction that can be returned to the dross furnace. The remaining slurry is vacuum filtered, yielding a clear brine solution and an aluminum oxide filter cake. Evaporation of the clear filtrate produces a high-purity fluxing salt for reuse in the dross furnace. Over 80 pct of the metallic aluminum is recovered in the aluminum-rich oversize fraction, while essentially all the fluxing salts are recovered by evaporation. This report contains the final results of an investigation on a process research unit scale, an economic evaluation of the method, and recommendations to further improve the process.

Jan 1, 1979

By T. A. Hendrickson

The Bohemia district, situated about 30 miles southeast of Cottage Grove, Oreg., in the Calapooia Range, has been the major producer of lead and zinc in Oregon. Sporadic production has been Maintained from the district since its early discovery about 1858. In 1942, a selective-flotation mill was built at the Champien mine, which operated for only a short time and was forced to close because of the war and lack of labor. The Champion mill reportedly has been operated as a custom mill for the treatment of ore from the Musick and Helena mines, located in the district sometime in the past. This report summarizes the results of laboratory ore-dressing studies made on ore samples from the Musick and Helena Mines.

Jan 1, 1951

By N. Kyriazi, W. Duerr, J. Shubilla, J. G. Kovac, J. Kravitz

A joint effort by the Bureau of Mines and the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, was undertaken to determine how well self-contained self-rescuers, deployed in accordance with Federal Regulations (30 CFK 75.1714), held up in the underground environment. This report presents findings regarding laboratory-tested breathing apparatus from the first year of a 5-yr program as well as other related findings. The SCSR's were tested on human subjects and on a breathing and metabolic simulator. These results indicate that the apparatus, if well-treated, perform as expected except for manufacturing defects or quality control problems, which are identified. However, when the apparatus are carried in and out of the mine every day and stored at the working section, they may suffer abuse that can be extreme. Physical signs of abuse, unless extremely obvious, frequently are not detected by the miners or the mine operators; this poses a danger to a potential user in case of emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1986

By G. R. Hopkins, E. W. COCHRANE

According to reports received by the United States Bureau of Mines , Department of Commerce , as of January 1 , 1930 , there were 412 completed refineries in the United States with a daily crude oil capacity of 3,755,585 barrels . This compares with 413 refineries of 3,509,540 barrels capacity on January 1 , 1929 , which indicates that whereas the number of refineries was practically unchanged , the total capacity increased 8 per cent during the past year . Of the completed plants as of January 1 , 1930 , 358 plants , of 3,634,825 barrels total capacity , were operating and 54 , with a capacity of 130,760 barrels , were shut down . Compared with a year ago , this indicates a decline in the percentage of the total refinery capacity that is inoperative . There has been a decided decrease in the number of shut-down plants since 1924 and 1925 , when one plant in every three was inoperative . Many of the inoperative plants of 1924 and 1925 were constructed soon after the boom times of 1920. Some of these were operated for a time but were unable to show a profit during 1923 and 1924 , when an overproduction of crude petroleum was accompanied by demoralized markets for refined products . Prices for refined products improved in 1925 and 1926 , but only a comparatively few of the shut -down plants , then partly obsolete , were able to obtain or renew their crude connections and compete successfully with the larger , more firmly established refineries . After five years or more of continuous idleness , a refinery would be rendered practically useless through corrosion and obsolescence . Consequently , most plants now being carried as " shut -down " have operated intermittently since 1923 . struction . A material change occurred in 1929 in the matter of plants under con- On January 1 , 1929 , there were 14 plants under construction , with a potential capacity of 99,000 barrels per day , whereas on January 1 , 1930 , there were only eight plants of 37,200 barrels capacity being built . This decline was due to the fact that the construction program in west Texas , which was at or near its height on January 1 , 1929 , was completed prior to January 1 , 1930 .

Apr 1, 1930

By R. A. Beall

A series of 45 zirconium ingots has been cast by the consumable electrode arc melting process with the object of analyzing the effects of power input from 50 to 230 kilowatts and reduced pressure furnace atmosphere to improve the quality of regular 8-inch-diameter production ingots made thereby. Electrode consumption rate, molten pool volume, melting efficiency, sidewall quality, arc stability, and yield efficiency are considered. The use of direct current and alternating current is studied. In conclusion, reduced pressure furnace operation is shown to promote electrical efficiency, ingot homogeneity, high metal yield, and are stability. INTRODUCTION Zirconium is a particularly difficult metal to melt because of its affinity for atmospheric gases and its solvent properties when molten. In addition, zirconium sponge as produced by the boll process contains minor amounts of magnesium chloride, which cause severe spattering luring melting, because of these difficulties with zirconium, and its sister metal titanium, near techniques have been developed to permit production of commercial size ingots. Among the more promising is the consumable electrode arc melting method.

Jan 1, 1955

By W. H. Young

THE BITUMINOUS coal and lignite industry increased substantially in 1962, compared with the 1961 figures. The major items of production, consumption, exports, and productivity increased. However, certain key items declined. The steady upward trend in mechanization failed to materialize for the third year; the percentage of total tonnage mechanically loaded remained the same as in the 2 previous years; and the tonnage mechanically cleaned was smaller than in the previous year. The percentage of total production mined by stripping and by augers increased slightly. Most significant was the continued decline in average value and employment. Production.-The output of bituminous coal and lignite in the United States in 1962-422 million tons-was 5 percent greater than the 403 million tons produced in 1961. Production was greater in 1962, owing largely to expanded consumption by the electric utilities and to more exports.

Jan 1, 1963

By R. V. Higgins

A numerical method is presented to calculate the pressure distribution in a petroleum reservoir that has irregular boundaries. The computer program is straightforward and requires minimal data preparation. The method can also be used to determine pressure distribution in many other types of underground reservoirs. In this method, the grid solution of the fluid-flow equations in a reservoir that has regular boundaries (previously published) was expanded to handle irregular boundaries. The computer program locates grid points at the irregular boundaries. The method of mirror images is then used to form a special stencil to determine the pressure at each of these points. Two examples are presented to demonstrate the applicability of the method for virtually any reservoir configuration.

Jan 1, 1972

By Raymond B. Lucas

"Distinction between Tripoli and Diatomaceous EarthMuch confusion exists both in the literature and in the trade as to the proper use of the terms tripoli, tripolite diatomeceons or infusoriai earth, and kieseigunr. All of these terms are often used synonymously by the trade and even in mineralogists and other reference books. Actually, tripoli is a ma- is a material of definite and distinct physical and chemical properties and all of the other terms belong to a different material with just as definite and distinct properties.Originally the term tripolite (loosely called tripole) was given to a diatomaceous cart from Tripoli in Northern Africa. Dena (J.D. Dana, A System of Mineralogy 6th Ed.) calls this material tripolite and gives no authority for the use of the terms tripoli. Between 1880 and 1890 the deposits near Missouri, were opened and the material placed on the market as ""Tripoli"" no doubt due to its resemblance in some respect to the original tripolite or diatomaceous worth from Tripoli. Since that time the term tripoli has with increasing definitenesss been reserved for the Seneca material and other siliceous of similar origin and physical properties, while all siliceous material of organic origin, containing dilators, has been called diatomaceous earth (or its synonyms infusorial earth, kiselguhr, etc.). Rottenstone is sometimes classed with tripoli."

Nov 1, 1920

By D. B. Eccleston

Natural gas and mixtures of natural gas and hydrogen were used as fuels in a laboratory engine to determine the relationship of emissions to air-fuel ratio and to establish practical lean limits for air-fuel ratio. Synthetic gas manufactured from coal (Synthane) and natural gas were used as fuels in a vehicle to obtain comparative data on emissions and performance. Results showed that lean limits for air-fuel ratio when using hydrogen-enriched natural gas were extended significantly beyond Chat of natural gas. Synthane pro¬duced exhaust that was significantly less reactive than exhaust from natural gas. With lean air-fuel ratios, the acceleration performance of a vehicle fueled with Synthane was improved over its performance when fueled with natural gas.

Jan 1, 1972

By G. A. Crowder

Far infrared spectra, most of them in the region 15-200 microns and for both the liquid or solution state and for the vapor state, were obtained for twenty-seven compounds.

Jan 1, 1965

By W. J. Crawford, P. M. Gruzensky

"Several experiments have been carried out in efforts to evaluate qualitatively a variety of electrolytes for refining bismuth. Most extensive work was done with the basic tartrate, hydrochloric acid, and hydrofluosilicic acid electrolytes. Deposits that are smooth and adherent can be obtained from these three electrolytes if low cathode current densities are employed. All three electrolytes were effective in purifying crude bismuth considerably, with additional purification indicated in each instance by a reelectrolysis step.With the basic tartrate electrolyte best results were obtained when the electrolyte was at 40° C. and contained at least 100 grams of bismuth per liter. An apparent disadvantage was depletion of bismuth from this electrolyte, causing the deposits to become spongy and nonadherent.The hydrochloric acid electrolyte had the greatest tendency to yield rough, dendritic deposits. Best deposits were obtained at cathode-current densities below 2 amperes per square decimeter. A small amount of glycerin helped to produce a smoother deposit, and adding sulfuric acid or methyl sulfuric acid retarded the deposition of impurities. Very good results were obtained in electrowinning bismuth from a bismuth trichloride-hydrochloric acid electrolyte.Smooth and adherent deposits were obtained from a hydrofluosilicic acid electrolyte, with very good refining as regards lead and silver impurities; however, higher reagent costs and slow decomposition of the electrolyte have discouraged its use.INTRODUCTIONMethods of recovering bismuth from ores and byproducts were underdeveloped for many years because of the limited uses for bismuth, the pharmaceutical industry being the chief consumer. In the past decade or so additional uses for bismuth, particularly in the metallurgical field, have brought about increased demand for the metal with the result that bismuth is being recovered from byproducts that were once discarded. In addition to such uses as low-melting alloys, solders, bearings, die setting, etc., some interest has been indicated in bismuth as a possible coolant for nuclear reactors. The advent of ductile bismuth and bismuth-alloy thermocouple wire has contributed greatly to temperature measurement, particularly in the below-zero range."

Jan 1, 1956

By Richard F. Link

The principal procedures for the statistical analysis of gold assay and other trace-element data depend on applying either the normal frequency distribution or the lognormal frequency distribution. The consequences of applying both methods are examined through reference to example data from United States and South African gold mines. It is concluded that for estimation of average grades, except for certain data with a very high coefficient of variation (ratio of standard deviation to mean), use of the lognormal distribution is ordinarily undesirable because bias may be introduced and little efficiency can be gained. However, if biased average grades can be tolerated, as in the examination of data from surveys in exploration geochemistry, use of the log-normal distribution may be desirable. Various statistical analyses are detailed, and the tables presented to implement the analyses are more complete than those previously published.

Jan 1, 1971

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

6. Development of Mine Sealant Material Systems 6. 1 Introduction The preliminary evaluation of material systems described in Section 3 led to the selection of the following four promising systems for further development: System A: Aggregate, Fly Ash System System B: Aggregate, Fly Ash, Urethane Foam System System C: Aggregate, Bulkhead, Light Expansive Concrete System D: Aggregate, Self-Supporting Thick Slurry Preliminary laboratory tests indicated that the building of effective bulkheads from one borehole would be extremely difficult. Two extra boreholes would be required adding to the overall cost of the system and making the system less attractive. Tests with light expansive concrete showed that bulkheads would be required, the material would not support itself. As a result, further development of this system was terminated. Foam concrete was selected as the most suitable material to be developed into a self-supporting, rapid-setting slurry. A laboratory investigation of its use for mine sealing was conducted during this program; the results are summarized in Section 6. 5 and details of the laboratory program are presented in Appendix B.

Jan 1, 1973

By William J. Campbell

These investigations were undertaken as part of a program to determine the optimum X-ray spectral lines to use for analyzing the wide variety of samples received by the X-ray Laboratory. Theoretical calculations and experimental data derived from these investigations show that longer wavelength spectral lines, > 2A, are very useful for many analytical problems. Because of the low fluorescence yield of the elements of atomic numbers 13-22 and the small depth of penetration of their X-ray spectral lines, these elements were originally considered to be insensitive; however, these studies show that the wide dispersion of their spectral lines, coupled with their weak beta lines, permits the use of wide collimation, thus increasing the line intensity. More importantly, the background due to scattered primary radiation is very low in the long-wavelength region.

Jan 1, 1959

By H. E. Peterson

This report revises an earlier publication by the Bureau of Mines on tungsten analytical procedures and expands the coverage by including appropriate procedures for the critical impurity elements that commonly occur in tungsten ores and concentrates (13).3 The basic methods described are not original, but many of the modifications to improve reliability and sensitivity were developed by the Bureau. Gravimetric and colorimetric methods currently used for the determination of tungsten in ores, mill tailings, and concentrates are described. Colorimetric procedures are preferred for low concentrations of tungsten, whereas either procedure is satisfactory for moderate concentrations. Conversely, a gravimetric method is preferred for the determination of tungsten in concentrates.

Jan 1, 1963

By H. C. Ko

Calorimetric determinations of low-temperature heat capacities and the standard enthalpy of formation were made by the Bureau of Mines for aluminum sulfide, A12S3. The standard entropy (S°), enthalpy of formation (?Hf°), and calculated Gibbs energy of formation (?Gf°) at 298.15 K are 27.93±0.05 call deg-mole, -155.6±0.9 kcal/mole, and -153.0±1.0 kcal/mole, respectively.

Jan 1, 1976

By William A. Beck

The K.T. Dome Mine in Owen and Henry Counties, Ky., has been operated intermittently under several different owners since the early nineteen hundreds. No record of total production is available, but it is said that during 1943 and 1944, while being operated by the Twin Valley Mining Co., 30 cars of zinc concentrates and 10 cars of lead concentrates were shipped. The vein can be traced for about 10 miles along the strike from Lockport, Henry County, to Big Twin Creek in Owen County. It pinches and swells both vertically and horizontally and is reported to average 20 inches in width. In order to develop additional reserves on the property, the Bureau of Mines drilled four holes on the south extension of the vein. Drilling disclosed that the vein dips to the west on the south side of the Kentucky River and is continuous along the strike and in depth. However, the extent of mineralization in the vein varies widely.

Jan 1, 1949

By George N. Aul

This report describes a method developed by the Bureau of Mines for sealing horizontal degasification holes so that they do not create a gas explosion hazard when intercepted by mining. A cement slurry is pumped into the hole through an injection pipe that extends to the back of the hole. Pumping continues until the slurry returns through the annulus to the hole collar. The hole is then shut in and the grout allowed to harden. Application of the procedure to six horizontal degasification holes at Eastern Associated Coal Corp.'s Honey Run shaft is discussed.

Jan 1, 1979

By P. G. Bennett

The Bureau of Mines developed a process using ion exchange to recover cobalt from spent copper leach solutions. A preliminary economic evaluation of the process indicated that about one-third of the capital cost was attributed to the total resin inventory, and one-third of the operating cost was required for reagents to remove iron from the ion-exchange eluates. An agitated Pachuca elution system was investigated in place of a fixed-bed elution system. The Pachuca system reduced the resin inventory by 27 pet when compared with the fixed-bed elution system. Processing fresh spent copper leach solution reduced the resin inventory by 20 pct and resin iron loading by 80 pct. Reagent requirements for removing iron from the eluates were decreased because less iron was extracted. The Pachuca system, along with processing fresh spent copper leach solution, reduced the total resin inventory by 47 pct. A revised cost evaluation of the cobalt recovery process was obtained to determine the effects of these process modifIcations. The estimated total capital cost for a plant processing 10,000 gpm of spent copper leach solution containing 26 ppm Co was $23.1 million. With credits for nickel, zinc, and copper byproducts, the estimated net operating cost was $5.10/lb of cobalt.

Jan 1, 1988