Search Documents

By Jay D. Dixon

The Bureau of Mines has developed structural design data for unreinforced concrete tunnel linings for drifts used in block caving stopes. Design data are given that consist of moment, thrust, and deformation coefficients from which bending, axial, boundary stresses, and structural deformations can be determined at any point on the lining. Data is given for circular, horseshoe, and rectangular linings, each with two different thicknesses and subjected to eight different loading conditions for drifts excavated in hard and soft rocks. The structural analyses performed are based on procedures that account for both the structural behavior of the lining and that of the drift and take into consideration deformational interaction that occurs between them.

Jan 1, 1973

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health, National Personal Protective Technology Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the seventh phase of testing from May 1999 to August 2000. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. The results indicate that most of the apparatus, if they pass their approved inspection criteria, perform satisfactorily. The deployed CSE SR-100s, however, exhibited significantly higher inhaled carbon dioxide (CO2) levels than new units, as they did in the previous two phases. Several Draeger OXY K-Pluses that rattled when shaken were found to have potassium superoxide (KO2) particles throughout the breathing circuit, including the mouthpiece. Draeger investigated the problem and developed a shake test to detect damaged units. The durations of new Ocenco M-20s were statistically significantly longer than those of deployed units, although only by 2 min.

Jan 3, 2002

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the dust suppression technique of applying foam to face drilling and crushing operations in a gypsum mine. Previous attempts to achieve effective dust control on face drills using other techniques, such as dry collection and boom-mounted external water sprays, have not been successful. The largest problem encountered when using these techniques has been the lack of sustained effective dust capture at the face. Results for two faces studied show that injection of the foam through the drill steel provided an average dust reduction of 95 pct. However, the use of foam on the crusher provided no dust reduction at the operator's position (because of good local ventilation) and a 27-pct average dust reduction for two feeders at a location midway between the operator's position and the crusher. The conclusions obtained from this study are that (1) foam can be an extremely effective dust control technique when used on localized dust sources such as dust generated within a blasthole during drilling, and (2) foam is only marginally effective as a dust control technique when used on nonlocalized dust sources such as dust generated during the feeder-and-crusher operation.

Jan 1, 1981

By M. C. Irani

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1979

By C. R. Stephan, N. B. Greninger, J. R. Lipscomb

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. bjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood- block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 1993

By George T. Faust, S. R. B. Cooke

"The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the preparation of pulverized coal for fuel. In this study the relative amount of surface in various products and samples had to be assessed. Because of the familiarity with screens and because of the simplicity of using the inverse ratio of the opening for ascertaining the amount of relative surface in the respective sizes, screens down to and including 270-mesh were used. This choice was made in full cognizance of the irregularity of screens, but it seemed that if the same screens were used throughout all the tests the relative values would be satisfactory.In dealing with the subsieve sizes, pneumatic elutriation was used to make several fractions to extend the sizing analysis into the range of hypothetical screens. This kind of a sizing analysis was thought necessary because it is familiar to all operators, and, furthermore, it is amenable to several ways of plotting curves that bring out the characteristics of various coals and various methods of grinding.The method of obtaining the data from which to set up the hypothetical screen scale is the subject of this paper. It consists in determining the average projected area of the particles in the respective elutriated products. By extending the ""area method"" to sieve sizes, a factor is found that may be applied to the subsieve sizes, and thus the scale is projected in a regular manner. This method avoids contentions about specific surface and steers clear of ""average diameter"" except as material sized on screens may be said to have an average diameter."

Aug 1, 1939

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

By W. S. Landers

In contrast to the large fund of information available on the carbonizing properties of Eastern U.S. coals, the experimental data available for most Western U.S. and foreign coals are meager. To supply some self-consistent data, the Bureau of Mines conducted 220 low-temperature carbonization assay tests at 500° C. in a laboratory-scale carbonization apparatus. The results are included in this report. The U.S. coals tested are from Alaska, Arizona, Colorado, Illinois, Montana, New Mexico, North Dakota, Pennsylvania, Ohio, Texas, Utah, and Wyoming. Assays were also made on coals from Canada, Ecuador, France, Greece, India, Mexico, the Philippine Islands, Thailand, and Yugoslavia. In addition, one assay of pine sawdust and one assay of a peat from Ireland are reported. Prediction equations were developed relating the yield of products of carbonization obtained at 500° C. in the assay unit to the proximate and ultimate analyses of the coals. The equations for predicting the yields of tar plus light oil, char, and gas, and the heating value of the gas, are considered good, each equation having a multiple correlation coefficient of 0.90 or higher. The equation predicting volume of gas obtained upon carbonization is considered as fair, with a multiple correlation coefficient of 0.84. A reproducibility study of the assay made on 10 replicate samples of a subbituminous coal indicated that the standard deviation of the individual products was 0.31 percent or less.

Jan 1, 1961

By Jeffery L. Kohler, Harvinder Singh, Jon G. Bredeson

A survey of electromagnetic noise reports was performed and a summary of the results are given. Industrial concerns were surveyed for techniques to minimize the effects of electromagnetic noise and are presented. The common types of communication links used in mines today are presented. A mathematical development was presented which determines the probability of bit errors versus distance for various types of communication links designed for in mine use. The probability of undetected errors for the protocols of the communication links is given together with burst error detection.

Jan 2, 1981

By Charles Vaught, Warren G. Lacefield, Ronald D. Wasielewski, Philip K. Berger, Henry P. Cole, John V. Haley, Shannon L. Price

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Computerized searches of the relevant data bases were carried out, along with identification of relevant articles and materials by personal contact with experts in many fields. The citations listed in this bibliography resulted from this systematic literature search and review. The computer searches and an analysis of this literature are described in technical report 1. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/ technical workplaces were described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training was explored. Research and development activities that may improve mine health and safety training were suggested. Most of the entries in this bibliography were assembled in 1984 through 1985. Study of these materials contributed to the completion of the project research that followed. This later work is reported in the project technical report 2 and the final report. This bibliography is most useful when combined with examination of technical reports 1 and 2 and the final project report.

Jan 7, 1988

By Kung-Lee Wang

FOLLOWING the rapid recovery of previous years, the U.S. economy continued the upward trend and moved forward moderately and sporadically during the first half of 1962. There was a slow-down in the recovery rate, which was especially notable in the third quarter. The economy recovered in the fourth quarter, and by the end of 1962 the gross national product amounted to $555 billion, a new high, 7 percent above that of 1961. Production, employment, personal income, and corporate profits all achieved new peaks, but unemployment continued high and the prospects for improvement remained poor. The economy again failed to us~ its full potential; 1962 was a good year, but not good enough. During 1962, all industrial production climbed from the low in January to a high in late summer which lasted through the fall, and declined slightly at yearend. Mining production followed this pattern closely and most sectors were approaching record highs. Most minerals gained in value and volume of production. The steel-associated minerals group was the only exception, and it sustained a small net loss. The nonfuel minerals industry opened the year at a high level, maintained this high level until late summer, with the peak in May, and drifted downward toward the end of the year. The gains recorded by nonferrous metal mining partly offset the loss of ferrous metal mining, resulting in a small gain for metal mining as a whole. The upsurge of construction material minerals output was primarily responsible for the substantial increase in production of nonmetals other

Jan 1, 1963

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989

By P. G. Clites

This study was undertaken to determine the effect of consumable-electrode vacuum arc melting on the properties of copper and to determine the applicability of the process to the production of cast shapes of copper. Ingots and castings were produced from electrolytic tough pitch copper (ASTM designation ETP), from electrolytic cathode copper (ASTM designation CATH), and from oxygen-free copper (ASTM designation OF). The products of this study were evaluated to determine the effect of the melting process on the removal of impurities from the copper and on the physical properties of the copper. The results indicate that consumable-electrode arc melting can be satisfactorily applied to the melting and casting of copper. Ingots prepared directly from electrolytic cathode copper contained slightly higher levels of impurities than are found in commercial oxygen-free copper, Excellent results were obtained with centrifugal castings of unalloyed copper, and reasonably successful static castings can be produced if proper mold and gating systems are employed.

Jan 1, 1963

By Charles L. Kimbell

Comprehensive data on market prices for crude minerals and mineral products for the world as a whole do not exist, and even the data that are available are not necessarily compatible between countries, particularly between the market economy countries and the centrally planned economy countries. Further, it should be evident that the actual delivered price for a small quantity of any specific commodity at some point substantially removed from a production facility or a seacoast port will differ appreciably from that for a large volume of the same product at or near its production source or a major import center. Nevertheless, the regularly published prices of selected major mineral commodities in key market areas can be regarded as indicative of general world price trends.

Jan 1, 1992

By William P. Diamond

Ventilation has long been the primary means of controlling methane emissions in underground coal mines. However, as mining has progressed into gassier areas of U.S. coal basins, supplemental means of methane control have become of interest, if not a necessity, for continued safe and productive mining operations. This paper describes the history and technology of methane drainage in the United States and other countries. The methane drainage technology developed in European countries is a valuable resource since their longer history of mining has already forced mine operators to deal with methane emission problems only now being experienced in the United States. Methods for assessing the need for methane drainage and the data required for planning and implementing an appropriate system are reviewed. The effectiveness of the various technologies for reducing methane emissions underground and/or the in-place gas content of individual coalbeds is illustrated with case studies. In addition to the safety and productivity gains to be realized from methane drainage systems, the potential for commercialization of coalbed methane is discussed.

Jan 1, 1994

By R. W. Dalzell

The performance characteristics, efficiency, and operating pressure of jute line-brattice systems were studied under varying underground conditions; various fabric grades and installation methods were used. The test results indicate that line-brattice system efficiency is dependent upon the method of ventilation the method of installation, porosity of fabric, and size of tight rib area.

Jan 1, 1966

By P. W. Jerant

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By J. H. Maysilles

The Bureau of Mines is conducting research on various technologies to recover alumina from domestic resources for feedstock to existing aluminum smelting capacity as a means to reduce dependence on imported bauxite, which represents 93 pct of U.S. aluminum requirements. One of the more promising technologies being investigated is the hydrochloric acid leaching of kaolinitic clay. In the hydrochloric acid leaching technology, alumina is recovered from iron-free aluminum chloride leach liquor and separated from impurity elements by sparging the liquor with HC1 gas to crystallize aluminum chloride hexahydrate (ACH). A large-scale crystallizer with a 336-gallon usable volume was constructed and operated to obtain engineering and design data for potential scale up and to demonstrate the ability of the technology to produce specification grade alumina. Test campaigns involving about 1,400 hours of operation were completed. ACH meeting all chemical purity requirements could not be produced by a single crystallization, but was produced by recrystallizing the product from the calcined kaolin clay leach liquor. Product crystals with a size distribution of more than 80 pct plus 100 mesh and 65 pct plus 65 mesh were made at a rate of 10 pounds of ACH/(hr)(ft3). The zirconium tube heat exchanger used to maintain constant process temperature operated with an over-all heat transfer coefficient of 420 to 500 BTU/(hr)(ft2)(°F).

Jan 1, 1981

By Clyde M. Pearce

The Lake Superior iron-mining district includes parts of the States of Michigan, Minnesota, and Wisconsin. The laws of each State provide for an industrial commission and for inspection of mines. The following extract from the General Orders on Mines, effective October 25, 1937, issued by the Industrial Commission of Wisconsin, is the only reference to the use of safety catches on mine cages or skips found in the laws and regulations in the Lake Superior iron-mining district: Order 316 - Cages for Hoisting Men. (c) Sides, Gates, and Safety Catches. ***Every cage shall be provided with safety catches of sufficient strength to hold the cage with its maximum load at any point in the event the hoisting cable should break. (d) Testing Safety Catches. The safety catches of cages and skips used to hoist men shall be kept well oiled and in good working order. They shall be tested at least once each month by tying up the cage or skip with hemp rope, lowering a few feet of hoisting cable on top of cage, then cutting the hemp rope, provided that any other system of testing, which is equally effective, may be used.

Jan 1, 1945

By Carla A. Kertis

Because coalbed discontinuities often pose serious economic and safety problems in underground coal mines, criteria were documented for the recognition and prediction of discontinuities in advance of mining. Pennsylvanian strata in Indiana and Armstrong Counties, PA, were deposited as part of fluvio-deltaic complexes with channel-phase sandstones as the predominant type of coalbed discontinuity. Coalbed isopach maps constructed for this study delineated numerous want areas (areas of no coal) with elongate to linear geometries. A comparison of coalbed isopach and corresponding sandstone isolith maps of the study area revealed many examples of a thick-sandstone, thin-subjacent-coalbed relationship. Nearly 60 pct of the want areas in the study area were found to lie subjacent to thick (> 20 ft [6 m]) sandstone accumulations. In addition to erosion of the coalbed, channels may contribute to coalbed splitting, coalbed thinning over paleotopographic highs, abnormal coalbed thick- nesses, and deterioration of coal quality. If these features are considered, then approximately 80 pct of all interruptions in the economic coalbeds in this area result from channel activity. By using the criteria developed in this study and described in this Bureau of Mines report, the occurrence of coalbed discontinuities may be predicted and anticipated in advance of mining.

Jan 1, 1985