Search Documents

By David E. Siskind

The Bureau of Mines performed a comparative study of nine sites at eight surface coal mines to determine if the presence of near-surface underground abandoned workings resulted in the generation of adverse long-duration, low-frequency blast vibrations. Six of the nine sites had underlying workings, and two had thick layers of low-velocity unconsolidated surface material. Extended seismic arrays were used to identify the vibration characteristics within a few tens of feet of the blasts and also as modified by the propagating media at distances over 1 mile. Production blasts and specially fired single-charge blasts allowed the determination of natural ground frequency and the influence of initiation delay timing. Vibration amplitudes from the production blasts at all sites exceeded historical norms, particularly at the greater distances. This contrasts with the near-normal results from single-charge blasts. Apparently, between-hole time delays were insufficient to separate vibrations from adjacent charges for the low-frequency waves present. Single-charge tests showed that the propagating media produced low-frequency, ground-roIl-type surface waves at nearly all sites. Large blasts at such sites could produce an unacceptable risk of vibration-induced cracks in nearby structures.

Jan 1, 1989

By E. Chin

Natural gas was the only economically significant mineral produced. A significant amount of the gas output was consumed in the production of nitrogen fertilizer and electric power. Proved reserves of natural gas were abundant and at least sufficient to supply most of the country's industrial and domestic needs for many decades to come. Other mineral production was of little importance to the Bangladesh economy, although there were prospects for developing some of the nonmetallic minerals. The flat river-delta terrain comprising nearly all of Bangladesh made the potential for discovering major, economically exploitable mineral deposits poor. The deep sediments, however, have good potential for crude oil or additional natural gas discoveries.

Jan 1, 1985

By Jr. Sharkey

The Bureau of Mines investigated gases from flash and laser irradiation of Pittsburgh seam (hvab) coal to determine the action of high temperatures on coal. Temperatures in excess of l,000° C were reached with both types of irradiation. Craters about 300 microns in diameter were produced in the coal with millisecond pulses from the laser unit rated at 1.7 joules' output. Gaseous products from laser and flash irradiations in vacuum contained 21 and 8 percent acetylene, respectively. Diacetylene, vinylacetylene, and other products to molecular weight 130 were indicated in the mass spectrum of the gas from the laser study. Single experiments were also conducted in which the laser energy, particle size of the coal, and atmosphere were varied. The results indicated that the distributions of products obtained from the flash and laser irradiations of coal were different from that produced in high-temperature carbonization.

Jan 1, 1966

By Edmond Chin

Mineral production was of minor importance to the country's economy, and Bangladesh was not a ranking world producer of any mineral commodity in 1980. Natural gas was the most important mineral exploited, and reserves were sufficient to allow a significant increase in its use. A greater proportion of the domestic heat and electrical energy needs could be filled by increased production and distribution of natural gas. Also, the export of natural gas was feasible either by pipeline to India or in the form of liquefied natural gas (LNG). Some nonmetallic minerals could be developed, as well as coal and peat, given sufficient capital investment. Bangladesh's strongly agricultural economy made fair progress in 1979.80.1 The major harvest of November-December 1979 turned out to be better than had been anticipated after an early drought left poor planting conditions. Secondary crops (harvested in February-March 1980 and June- July 1980) were excellent. There were prospects for a record harvest in fiscal year

Jan 1, 1982

By Jamie Girard Dwyer, Edward McHugh, Stanley Miller, Jeffrey Whyatt

This user's guide covers the operation of a suite of three computer programs-Bplane, Bstepp, and Bwedge. These programs can be used to evaluate the potential for plane shear, step-path, and wedge failures along the crest of a slope bench. Such failures reduce the width of a catch bench and may compromise the bench's ability to catch rolling or sliding material before it reaches miners working below. The Bplane and Bwedge programs address sliding of blocks defined by continuous planar joints. The Bstepp program examines sliding of blocks defined by more complex failure surfaces that include steeply dipping cross joints and may even include breaks across small bridges of intact rock. The programs are applicable to jointed rock masses where the joints are small relative to the overall slope and form a number of sets with uniform statistical characteristics within a slope sector. The theoretical basis, application, and operation of these programs are described.

Jan 3, 2007

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,310-acre Diablo Mountain (Additional) study area (OR-001-058), in order to evaluate its identified mineral resources and occurrences. The study area lies along the east shore of saline Summer Lake in Lake County, OR, about 145 miles southeast of Bend and 45 miles northwest of Lakeview. The climate is semiarid and temperate, and the study area is almost treeless. Geologically, the (Additional) study area is in a region of fault block-formed mountains and basins, characterized by interior drainage. The area is mainly underlain by unconsolidated Quaternary and Pleistocene lake and playa sediments, which may include subsurface evaporite mineral deposits and resources. Near the center of the eastern margin of the study area are an occurrence of dolomitic limestone of unknown extent, and an area of basalt outcrop totaling 1.5 square miles. A veneer of windblown sand covers about one-half the study area.

Jan 1, 1989

By Donald P. Blasko

The first well that produced commercial quantities of oil in the Cook Inlet Basin of Alaska was completed in 1957. Since that time oil production in the basin has increased rapidly and by the end of 1969 had reached an annual rate of 74 million barrels. Five major oilfields had been developed, and two additional discoveries awaited development. Estimated amounts of recoverable oil by primary and secondary recovery methods total 2.7 billion barrels, or 36 percent of the estimated oil originally in place. Repressurization by injecting gas or water in formations containing undersaturated oil has significantly increased the volume of recoverable oil. All production has been from formations of the Tertiary age; that much of it is from depths of 10,000 feet or more is unusual for Tertiary formations. The oils are low in sulfur and contain low to moderate amounts of asphalt.

Jan 1, 1972

By Robert L. Lagace, N. Albert Moussa

The objective of this project was to perform a preliminary study to determine the desirability/practicality of burying the communication cables in underground mines in order to protect then from the effects of fires and explosions We conducted discussions with Government and industry specialists on the physics of mine fires and explosions, mine disaster fighting, rescue, and investigation activities, and on nine operations. In addition we examined published experimental work and selected detailed NSHA accident reports on fires and explosions in underground mines. We found the overall desirability /practicality of cable burial must be regarded at this time as highly questionable, because of its benefit limitations to special sceneries, its practical operational shortcomings, and the availability of alternative cable protection options.

Jan 2, 1982

By A. J. Leighton

An improved mathematical model with the attendant computer program to calculate multiphase fluid flow in petroleum reservoirs is presented. The model is used to simulate the behavior when a fluid is used to displace hydro-carbon fluids in a reservoir. The method is an expansion of a previously published method, in Bureau of Mines RI 7011, but handles constant injection rate as an alternative to constant pressure. Program documentation is provided along with thorough explanations of the added program features. Using the program, the petroleum engineer can calculate oil recoveries for different flood patterns and operating conditions and select the conditions most likely to optimize recovery. Experience with the previous model demonstrated the need for the improvements in order to simulate reservoir behavior more accurately. The improved method will result in improved oil recovery. In this paper, the significant improvements are described in detail so that anyone interested can put the program to use.

Jan 1, 1975

By J. W. Chester

The rapid depletion of zinc-lead ore reserves and the rising costs of exploration have been major factors in the decline of mining activities and explorations for additional reserves in the Tri-State mining district. There is a need to develop new or adopt known, improved exploration techniques that will appreciably lower the costs of exploration. Demonstration of the practicability of using improved techniques to indicate, rapidly and cheaply, mineralized areas or geologic structures where more intensive explorations are justified could stimulate the search for and discovery of additional ore reserves. Various operators in the Tri-State district have used geophysical surveys to some extent since 1928 to guide exploratory drilling. Some geophysical investigations have also been made in the district by the State Geological Surveys of Kansas (11)3/ and Missouri (8, 13) and by Federal agencies (16), with the objective of directing exploratory drilling to areas where geologic conditions favored ore deposition. Many factual data obtained have not been published. The investigations generally have not been broad enough to permit conclusive evaluation of the usefulness of the geophysical techniques in all parts of the district.

Jan 1, 1959

By Manuel Gomez

A computerized, interpolative mapping technique based on the moving average method was shown to be adequate to estimate the between-drill-hole values of coal-seam variables. The forecasting of the spatial distribution of coal properties along the seam was of three kinds: (1) Estimation of the variable of interest on a regional basis from widely spaced sample points, (2) prediction of coal properties for product control from closely spaced data, and (3) prediction of coal properties for specified benches, or layers of the coal seam, from closely spaced sample points. Estimates obtained with the computerized, interpolative mapping procedure were useful in the delineation of seam thickness, elevation, and overburden and in the estimation of sulfur and ash concentrations during the early phases of exploration. This grid interpolation technique was found adequate to adjust between-drill-hole values for trends resulting from the combined effect of several variables on a measured response. This information, coupled with statistical and geologic data that can be obtained in the exploration phase of mining, enlarges the information base available for coal-mine development planning, energy forecasts, and environmental control associated with fossil fuel power generation.

Jan 1, 1972

By R. D. Leitch

"INTRODUCTION This report is another of the series on the effect of drouth and low water on the pollution of streams by coalmine drainage. A previous report3 dealt with work on Bennett Branch of Sinnanahoning Creek, Pa. This report deals with the results obtained during a similar study of Black Lick Creek, Two Lick Creek, and Yellow Creek. All of these belong to the same drainage system. Two Lick Creek is a tributary to Black Lick Creek, and in turn Yellow Creek is a tributary to Two Lick Creek, as shown in Figure 1.Black Lick Creek was of such a volume that a seasonal investigation was not entirely feasible. Yellow Creek was found to have mines only near the mouth, except a few of status unknown to the writer at the extreme head-waters, and the stream was also more or less inaccessible for regular and frequent sampling. Two Lick Creek was found to be most suitable of the three.ACKNOWLEDGMENTThe work reported has been carried on under the direction and with the advice of Dr. R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station."

Jul 1, 1931

By Thomas G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a chalcopyrite ore. The purpose was to obtain a direct comparison between moderate-temperature and elevated-temperature in situ leaching of copper trom minus la-inch ore and to analyze the sulfuric acid and oxygen requirements of the leaching system. Experiments employing oxygen were conducted at 35° and 90° C on 362-and 367-1b ore charges, respectively, under flooded conditions and at 400 psig. At 90° C, 47 pct of the copper was extracted in 913 days of leaching; at 35° C, 27 pct of the copper was extracted in 915 days. Diffusion into and out of the ore fragments con-trolled the rate of leaching. Oxygen consumption was 1.46 lb/lb of copper extracted at 35° C and 3.15 lb/lb of copper extracted at 90° C. Sulfuric acid requirements of the ore were 5.49 and 7.48 lb/lb of copper extracted at 35° and 90° C, respectively.

Jan 1, 1982

By John H. Hild

The topography of the Jamestown fluorspar area is rough and ranges from 6,400 to 8,000 feet in altitude. Some fluorspar was mined as early as 1870, but mining really did not begin in earnest until 1940, and up to July 1947 it is estimated that 272,500 tons of fluorite was mined and milled. In 1947 the General Chemical Co. was mining fluorite and milling it in a 200-ton-a-day mill at Valmont, 7 miles east of Boulder, and the Ozark-Mahoning Co. was milling ore in a 100-ton-a-day mill at Jamestown, using ore mined, by H. M. Williamson & Son. These fluorite deposits comprise veins in a granite country rock. The Bureau of Mines drilled eight holes, aggregating 2,579.1 feet, on the Blue Jay vein; four holes, aggregating 1,434 feet, on the Chancellor; and one 350-foot hole on the Nations Treasure. Fluorite of a minable grade and width was found in 10 of the holes drilled. In this report the location and accessibility, physical, features and climate are described and a brief history of the district is given. The deposits and character of the ore and sampling and analyses are described, mine workings are outlined, and work performed by the Bureau of Mines is summarized. Diamond drill logs are shown in appendix I, and 'Sample analyses are tabulated in appendix II.

Jan 1, 1949

By John R. Benham

The West Pioneer RARE II study area, No. 1-006 (fig. 1), has Figure 1.--NEAR HERE a high molybdenum resource potential. Two molybdenum-bearing areas are being explored by Utah International and by Cyprus-Moly Corp, Inc. using geophysical exploration and diamond core drilling. The study area also contains potential resources of gold and silver at six prospects: the Bear Paw (Ibex), Black Bear, Coeur d'Alene, Franklin No. 1, Martin, and Maynard. In addition, the Black Rear and the Martin contain possible copper, lead, and molybdenum resources. Most of the workings are caved.

Jan 1, 1981

By W. L. Anderson

Standard tellurium analytical procedures were modified to obtain the greater sensitivity needed to support a survey of tellurium resources by the Bureau of Mines. Resulting volumetric and spectrophotometric methods for determining tellurium in all types of tellurium-containing materials are described. Sample decomposition and preliminary separations of interfering selenium, gold, and silver are the same in both procedures. The volumetric method is applicable to samples containing a minimum of 10 parts per million of tellurium, In this method the tellurium is reduced to elemental form, and the colloidal suspension is titrated with 0.01 normal iodine solution. The weight of sample for analysis, from 0.25 to 10 grams, should be selected so that the sample contains 0.1 to 5 milligrams of tellurium. To insure accuracy, duplicate samples should be run and the results averaged, particularly on samples of low tellurium content: The limit of determination is 0,001 percent tellurium, which is equivalent to 0.1 milligram of tellurium when using a 10-gram sample. The spectrophotometric method is particularly applicable to low-tenor materials containing from 0.5 to 50 parts per million of tellurium. Up to 10 gram samples are required for making accurate determinations in the low-concentration range. The sample used should contain between 5 and 100 micrograms of tellurium. The turbidity of a colloidal suspension of tellurium prepared from such a sample is determined in a spectrophotometer .t at a. wave-length of 440 millimicrons, and this value is compared with those of standard samples containing known amounts of tellurium.

Jan 1, 1963

By Sol Weller

The Fischer-Tropsch synthesis consists of the formation of long-chain hydrocarbons by passage of carbon monoxide-hydrogen mixtures over metal catalysts, usually based on iron, cobalt, nickel, or ruthenium, at temperatures in the range 180°-300° C., and at pressures of 1-15 atmospheres. Although the reaction has been known and studied for more than 20 years, the mechanism by which it occurs is still poorly understood. One approach to understanding is to consider the effect upon the course of the synthesis of variations in each of the important operating variables. Consideration of the experimental data pertaining to these variables may suggest an over-all picture describing the synthesis - a picture which, in turn, would have to be consistent with all the known facts. The first part of this paper will be concerned with such a consideration of operating variables; the second portion will discuss recent work pertaining to the role of metal carbides as intermediates in the synthesis.

Jan 1, 1949

By R. D. Leitch

The work of the United States Bureau of Mines on stream pollution by coal-mine drainage has included a study of seasonal variations in acidity and volume of several streams in Pennsylvania. The acidity of these streams has been determined during the two or three years prior to 1930 and the results may be considered to represent "normal" low water conditions. The summer of 1330, however, was unusually dry and represents what may be termed "extreme low water conditions on these streams. This report is a comparison of the results obtained for extreme low water of 1930 and for other years. The streams investigated were Buffalo Creek in Somerset County, Indian Creek (lower 5 miles) in Westmoreland County, Little Toby Creek in Elk and Jefferson Counties, Daguscohonda Run in Elk County and West Creek in Elk and Cameron Counties. These will be treated separately in the order given. Most of the descriptive matter and physical data pertinent to the streams and drainage basins are taken from published reports of the Pennsylvania State Water Supply Commission, 1917.

Jan 1, 1931

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines have been exploring recent advances in the use of strain-softening constitutive laws that approximate shear fracturing. The purpose of these tests is to investigate shear-fracture-related rock bursts in hard-rock mines. The capabilities and remaining problems in the use of strain-softening laws in finite-element, distinct-element, and finite-difference methods are reviewed. Performance of the finite-difference implementation of strain softening is compared to classic experimental results and observations of rock mass behavior in the Coeur d'Alene Mining District of northern Idaho. The results show promise for developing methods to identify the general location and orientation of shear fractures and their sequence of occurrence, but such methods cannot be relied upon to quantify post-fracture loads or displacements accurately. Uncertainty over the amount of energy consumed by failing rock and the dependency of energy consumption on model mesh definition prevent direct application of the results to analyses of rock bursts.

Jan 1, 2010

By H. E. Powell

Because of increasing consumption of high-and super-duty refractories, the Bureau is studying the feasibility of beneficiating submarginal and marginal clays. Diverse mineral dressing tests were used to beneficiate samples from the east-central Missouri fire clay district. Standard ASTM tests were used to determine refractory properties of both crude and beneficiated clay samples. Marginal and submarginal clays containing impurities were effectively beneficiated by both wet-cyclone and wet-table treatment, but the wet-cyclone treatment was cheaper. Ion-exchange resins in the hydrogen form will probably prove more effective in removing potassium, the only alkali in Missouri fire clays to be a problem. Resins with greater cross linkage are more effective than resins with less. Roasting the crude clays before removing alkalis by chemical leaching was ineffective. By applying ultrasonic energy at a frequency of 10 to 25 kilocycles to aqueous suspensions of the clays, subsequent ion-exchange extraction of potassium was slightly improved. Higher frequency ranges did not help.

Jan 1, 1963