Search Documents

By J. E. Matta

The Bureau of Mines has developed a tracer gas method for measuring leak-age through permanent mine stoppings. In this method, a temporary brattice is erected in the same entry as the leaking permanent stopping. Leakage was evaluated from concentration measurements of a tracer gas introduced into the space between the stopping and brattice. Stopping leakages ranging from 15 cfm to 265 cfm were simulated in an underground coal mine. Leakage values determined by the new method were within 10 pct of the known values.

Jan 1, 1978

Efficiently clear ice and frozen materials from ore-handling equipment. Approach Compressed air-propane torches that develop a high energy flame jet were used instead of ordinary propane torches. How it Works A high velocity high temperature stream of gases impinges on the ice and frozen materials to both melt and blast them away. This hot gas jet is at 3,000°F temperature and moving at 3,000 feet per second. In the photograph below, the jet is being used to clear frozen taconite from a grizzly. The functions of the compressed air-propane torch are as follows. The air heater assembly, which is mounted on a wand, con-

Jan 1, 1980

Develop a curved ray geotomographic program with constraints to counteract non-uniqueness in order to improve the reliability of seismic tomographic imaging of geological structure in mining regions. Background Seismic tomography provides a two-dimensional image (tomographic reconstruction) of the distribution of the seismic velocity in geologic structures using measured travel times of seismic waves crossing the area. It can provide a more complete representation of features be¬tween boreholes than other crosshole processing methods that measure only average properties or borehole logging methods that measure properties only near each borehole. Seismic tomography has many mining applications. They include locating geologic structures of contrasting seismic velocity, detecting fractured regions where the seismic velocity is low, and monitoring solution injected above the water table where the increase in saturation increases the seismic velocity. Thus, tomographic imaging techniques show great promise for detecting and locating geologic hazards that affect the productivity, safety, and environment of mining operations.

Jan 1, 1992

To recover metals as sulfide concentrates from contaminated waste streams using hydrogen sulfide (H2S) generated by the bacterial digestion of waste organic materials. Approach The goal of this research is to develop a treatment method for metal mine effluents that will rival the cost and convenience of conventional lime treatment, and that will provide better effluent water quality, result in less expensive sludge disposal, and allow for the selective recovery of metals.

Jan 1, 1993

Reduce injuries caused by slips and falls from large haulage vehicles. Approach Replace the flexible-cable or chain-type lower ladder steps, with steps that extend closer to the ground and do not sway when stepped on. Modify dimensions of entire ladder to new industry recommendations. How It Works New lower ladder steps are supported by side pieces made of pretensioned, solid-wound, coil springs fabricated from high strength steel. Unlike conventional crash-resistant steps, which flex or swing freely when stepped on, the spring supported steps can maintain the same inclination as the fixed upper portion of the ladder while supporting an average-weight operator. The steps are also highly resistant to collision damage because they yield on impact if rammed into obstructions such as rocks or berms. See photograph.

Jan 1, 1980

Develop new technolgies and techniques which enable recovery of strategic and critical minerals such as cobalt from domestic resources, thereby easing the U.S. dependence upon foreign producers for these valuable commodities. Approach The Bureau of Mines, through research, developed a process which uses mineral beneficiation techniques to recover cobalt-rich products from Missouri lead ores. Before development of this process, cobalt was lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minimum impact on present production did not exist.

Jan 1, 1989

By Launa Mallett, Charles Vaught, Michael J. Brinich

The lack of good communication is a very real problem in mine emergencies. Sometimes critical information is not communicated to those who need it to make decisions. At other times, those on the receiving end of a warning do not think to ask the right questions. What happens in underground coal mine fires is a case in point. The authors interviewed 48 workers who escaped three serious fires in western Pennsylvania. In each case the location of the fire was known but did not get communicated to many of those who had to evacuate. Sometimes, even the nature of the problem was not clearly communicated. Some workers began their evacuation knowing nothing about what was happening. In an effort to improve emergency communication National Institute for Occupational Safety and Health (NIOSH) researchers worked with safety professionals to determine what sorts of information are critical in a mine emergency. An extensive list was generated, which proved too long to be remembered by individuals. The list was therefore collapsed into six categories. A communication protocol was derived from these categories.

Permit visual inspection of underground cavities dam the surface. Approach A closed circuit TV camera and a 35mm still camera are lowered down a borehole, and remotely operated. How It Works A platform holding the cameras, and other equipment is lowered on a graduated cable until the depth of interest is reached. Then a quartz lamp and the TV camera are turned on. The television picture is monitored at the surface and recorded on video tape. Areas of special interest are photographed with a 35mm still camera. These photographs contain more detail than TV images because photographic film is capable of higher resolution than a TV transmission.

Jan 1, 1979

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of three samples collected from the Kidney seam, in the Northern Field of the anthracite region. Removal of the sink 1.70 specific gravity material from the samples collected would result in greatly reduced ash contents at yields in excess of 90 percent. The Kidney seam, in the locations sampled, proved to be a low-ash anthracite containing an unusually high percentage of float 1.45 specific gravity material.

Jan 1, 1970

Provide sound battery safety guidelines for mine workers who maintain mobile surface mining equipment. Approach Battery-related accidents account for about 5 percent of all nonfatal disabling injuries in coal and metal nonmetal surface mines. These accidents occur despite the fact that appropriate battery safety technology (maintenance-free batteries, cable removers, fault detectors, hot-jumping systems, etc.) exists. Mine operators are not always aware of the safety measures that could be taken because this safety information is widely scattered in numerous unrelated technical reports, vendor brochures, and journal articles. A literature search of these reports and a review of relevant industry standards, handbooks, and references on battery safety, followed by discussions with mining company and MSHA personnel, provided the Bureau of Mines with the background necessary to develop procedures for proper and safe battery usage. These procedures were condensed and written in nontechnical language to serve as guidelines in assuring battery safety during maintenance of mining equipment.

Jan 1, 1986

By E. G. Valdez

The Federal Bureau of Mines, in cooperation with Ford Motor Co., investigated the recovery of polyurethane foam and other assorted plastics from the nonmagnetic reject of automobile shredders. Preliminary studies were con-ducted on a 1957 hulk augmented with additional foam and assorted plastics. The proposed flowsheet developed by the Bureau from the preliminary studies consists of a combination of screening, water classification, and gravity separation. The process was then tested on reject from two shredded 1972 cars. All of the foam and between 52 and 70 pct of the assorted plastics were recovered. The composition of the reclaimed foam concentrates ranged from 46 to 66 pct foam; the concentrates were hydrolyzed in laboratory tests by Ford Motor Co. to produce a reusable liquid mixture of polyether glycol monomers and toluene diamine.

Jan 1, 1975

Provide blasting-resistant, quickly reusable stoppings for large mine openings. Approach Stoppings are assembled using roof-to-bottom panels of brattice held together by Velcro seams that peel open when struck by a strong air blast. How It Works The Velcro seam is designed to open when exposed to forces lower than would normally damage the brattice. When the seams partially open, they relieve the blast air overpressure to prevent damage to the brattice panels and their anchoring devices. A stopping is returned to service by reclosing the Velcro seams. To hang a brattice panel, its top is stapled to a board, and wrapped once or twice around it. That assembly is then attached to the roof with bolts. The length of the board should be a foot less than the width of the panel to allow for the sealing seam on each side of the panel. The boards are installed end-to-end in an approximately straight line across the roof of the mine opening.

Jan 1, 1979

To restore ventilation and prevent the accumulation of explosive or toxic gases by quickly installing substitutes for stoppings blown down by an explosion. Approach Temporarily replace blown down stoppings with a parachute-shaped brattice which can be erected in minutes. How It Works The self-sealing brattice is secured to the roof, ribs and floor by anchoring its nylon edge strip at several points using extensible poles, shads, or available projections such as roof bolts. The air pressure in the entry pops open the chute of lightweight sailcloth, forcing it tightly against floor, roof and rib. See Figure 1. This emergency brattice has been tested at two locations in the Bureau's Experimental Mine at Bruceton, Pennsylvania. In a test last December, one MESA inspector wearing full rescue apparel (including self contained breathing apparatus) installed a self sealing brattice in an entry at the Bruceton Mine. Although he did not have any previous experience with the device, he easily erected it in slightly less than 10 minutes, using two extensible supports (pogo sticks). Research to improve and refine the self-sealing brattice is continuing.

Jan 1, 1977

Provide roof to floor closure rate measurements during underground mining, especially retreat mining of coal pillars, thereby helping the miners predict an imminent roof fall. Approach An electronic device and rugged potentiometric extensometer were developed to provide a means fur measuring total closure and the rate of closure. How It Works An intrinsically safe, battery operated instrument is enclosed in a rugged, hand carried field case. The unit is constructed using low-power, integrated circuits to provide minimal battery drain. Two digital Light Emitting Diode (LED) readouts are used; one displays the rate, the other displays the total closure. The unit will measure one extensometer continuously or two extensometers alternately. Two potentiometric extensometers with a closure measurement range of 6 inches are attached to the readout unit. As the roof to floor closure changes, the potentiometric resistance

Jan 1, 1982

To produce industrial-grade titanium castings by processes that are nonpolluting and lower cost than the currently used rammed-graphite process. Approach Foundry-grade zircon and olivine sands, bonded by waterglass or bentonite, are used to make shell or rammed molds which require relatively low-drying temperatures and do not generate noxious fumes during drying or casting. Procedures Three separate processes have been developed which meet the stated pollution and cost goals. These are: 1. Waterglass-bonded rammed zircon or olivine sand molds are dried at 480°F, zirconia washed, redried, and used in an inductoslag or skull-casting furnace. 2. Waterglass-bonded zircon or olivine sand shell molds are formed at 560°F, cured at 620°F, zirconia washed, dried at 480°F. and used in an inductoslag furnace. 3. Rammed zircon and olivine sand molds are bonded with western bentonite, zirconia washed, dried at 980°F, and used in an inductoslag or skull-casting furnace.

Jan 1, 1981

By T. O. Llewellyn

The Bureau of Mines conducted laboratory batch beneficiation tests on a waste granite sludge from New Hampshire to determine the feasibility of recovering a reusable silicon carbide product. The granite sludge responded to attrition scrubbing, desliming, and flotation in either alkaline or acid circuits using fatty acid as a collector. Recovery of over 80 percent of the contained silicon carbide at grades of up to 96 percent SiC was obtained.

Jan 1, 1975

Utilize innovative processing technology to prepare high-purity, ultrafine advanced ceramic powders with little or no contamination occurring during the milling process. Advanced ceramic materials made from these powders could substitute for high-temperature alloys containing critical materials such as chromium, cobalt, and nickel. Approach Modify and evaluate the Bureau's turbomill, developed earlier to grind a variety of ceramic raw materials (clay, mica, and talc), as a milling or size-reduction technique for hard and abrasive advanced ceramic powders, such as silicon carbide. Background Powders for producing ceramic materials, such as silicon carbide. silicon nitride, alumina, and zirconia, which arc being considered for use in severe applications requiring high-temperature and/or corrosion resistance, are very difficult to reduce to fine sizes for processing into finished parts. Traditional techniques of particle size reduction, such as ball milling and jet milling, are very energy intensive and/or slow. These traditional techniques often produce materials that have a nonuniform particle size distribution and are contaminated by the milling media or container.

Jan 1, 1989

By James W. Vogh

The report covers initial findings in an experimental program to identify diesel exhaust odorants and determine their contributions to diesel odor. The approach was to isolate selected component groups from exhaust and to evaluate the contribution of each group to exhaust odor. Results were obtained for those carbonyls and phenols that could be isolated from exhaust through inter-mediate conversion to oxime derivatives. Unsaturated aliphatic aldehydes and sterically hindered carbonyls were not included. Hydrocarbons intermediate in the diesel range were "also evaluated and an odor contribution was found from those of the aromatic group. The evaluated carbonyls, phenols, and hydrocarbons were found to account for about 20 pct of the total odor in exhaust from an indirect-injection engine during idle. For exhaust from the indirect-injection engine operating under load and from a direct-injection engine at no load, these compounds were found to have no significant levels of odor.

Jan 1, 1972

Remotely monitor overburden response to longwall mining using time domain reflectometry (TDR) and a combination of hardware and software, as part of the U.S. Bureau of Mines (USBM) program to characterize subsidence. Background TDR was developed in the 1960's as a method to locate, discontinuities in coaxial transmission cables. In this method, voltage pulses sent along a cable are reflected by cable defects. The pulse reflections are used to determine the type and magnitude of the defects. The TDR concept was extended to material property measurement by embedding cables into particular materials and evaluating the cable's dielectric behavior as material properties were modified. This technique was adapted by the USBM in 1978 for use in monitoring rock movement during underground mining. The same concept is utilized today. A coaxial cable is grouted into a rock mass that is expected to deform. Progressive rock movement causes the cable to deform, as shown in figure 1, and changes to occur in the cable's electrical properties, which then produce changes in TDR reflection signatures. The technology has advanced to the point where it is now possible to distinguish shear deformation from tensile deformation and to quantify rock mass displacements by analyzing the TDR signatures.

Jan 1, 1995

Minimize failures or inefficiency in the operation of in situ mining wells. Approach The proper design, construction and development of wells are important to any in situ leaching operation. To permit cost-effective production from an underground ore body by leaching it in place, many wells are normally installed. Construction and maintenance costs increase with the number of wells, and poor construction and maintenance procedures result in production losses and negative environmental impacts, To minimize these losses and impacts, the Bureau of Mines conducted an investigation to determine the optimum in situ well construction and operating procedures for the minerals industry. Factors considered during the investigation included drilling equipment and procedures; types of well casing and grouting; completion methods, e.g, screening or perforation; and system maintenance. The data collected were used to prepare a manual that offers guidelines

Jan 1, 1984