Search Documents

By Christopher Mark

Roof bolt system design means the selection of the type, length, capacity, and pattern of bolts for a particular application. Despite research efforts dating back 50 years, no design methodology has found wide acceptance. This paper begins by identifying four mechanisms that roof bolts use to reinforce the ground. It argues that the reinforcement mechanism is determined by the roof geology and stress level, not by the type of bolt. Next, the attributes of roof bolts are discussed in the light of recent research, including anchorage mechanism, installed tension, length, capacity, timing of installation, and installation quality. Several significant areas of controversy are identified. Design methods from around the world are discussed, including those based on empirical research, numerical modeling, and roof monitoring. Finally, some simple guidelines for preliminary design of roof bolt systems are proposed based on statistical analysis of roof support performance at 37 U.S. mines.

Jan 10, 2000

By Kenneth H. Johnston

Information and data necessary for research on improving methods of oil recovery from low-permeability reservoirs and for comparison and evaluation of performance of such reservoirs with those producing from more permeable sands were obtained. Core analyses, well logs, production tests, well stimulation techniques, primary and secondary production records, and data on two water-flood projects were examined for wells producing from the Bartlesville sand, West Avant field, Osage County, Okla. Overall recovery from the study area was generally poor with only 9.0 percent of the pore volume recovered to January 1, 1968. Larger fracture treatments (8,000 to 12,000 gal) could have resulted in an increase in primary oil recovery. Secondary recovery by water-flooding accounted for only 1.9 percent of the pore volume because of the inability to control the large volume of injection fluid that escaped from the flood patterns and the excessive volumes of water produced with the oil. Future waterflood development in other low-permeability reservoirs should include the drilling of new input wells, use of injectivity surveys to locate possible natural fracture systems, or zones of high permeability, and control of injection fluids by altering flood patterns and/or plugging of the more permeable zones.

Jan 1, 1968

By F. Garcia, J. Cervik

The cross-measure borehole technique has been shown by the Bureau of Mines to be an effective method of controlling methane liberated by fracturing the roof strata in longwall gobs where overburden is less than 750 ft (229 m). Boreholes are drilled into roof strata before mining operations affect the roof strata. Longwall mining fractures the roof strata and releases methane from source beds. Surface exhausters or vacuum pumps are used to draw the gas to the surface through an underground pipeline and vertical exhaust hole. The captured methane is thus prevented from entering the mine's ventilation system. About 71 pct of the methane produced by longwall mining in the Lower Kittanning Coalbed was captured by the cross-measure boreholes. Borehole spacing is an important factor affecting the performance of the technique. Interference tests and measurements of methane flows in return air indicate borehole spacing in the Lower Kittanning Coalbed should be limited to about 200 ft (61 m) except on the first 600 ft (183 m) of the longwall, where spacing should be reduced to about 100 ft (30 m) to capture the large quantities of methane released when the first large roof fall occurs. Comparisons between measured and calculated gas pressure differentials on boreholes indicate borehole length can be reduced from 280 to 140 ft (85 to 43 m), which reduces drilling costs significantly. Additional experimentation is necessary to verify the calculations.

Jan 1, 1985

By Benjamin W. Haynes

Materials from phosphate rock mining and processing were analyzed for fluorine and uranium content as part of the Bureau of Mines program to more effectively recover resources from mining and mineral processing reject materials. The analysis of both feed and waste materials generated in the beneficiation and acidulation of phosphate rock was performed to obtain information on the disposition and concentration of these elements in phosphate rock processing streams. Fluorine was determined by a distillation-titration method and by ion chromatography. Uranium was determined by the dibenzoylmethane (DBM) method, the reliability being confirmed by roundrobin analysis of samples within Bureau of Mines research centers. National Bureau of Standards (NBS) Standard Reference Material (SRM) 120b-Phosphate Rock was also analyzed for fluorine and uranium to verify procedures and results. Fluorine values ranged from 0.3 wt-pct in gypsum filter cake to 3.7 wt-pct in phosphate rock concentrate. Uranium ranged from less than 5 µg/g in gypsum filter cake to 200 µg/g in a dried clay slime.

Jan 1, 1981

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove, grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 2 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1970

The National Institute for Occupational Safety and Health (NIOSH) National Personal Protec-tive Technology Laboratory (NPPTL) and the Mine Safety and Health Administration (MSHA) conduct a Long Term Field Evaluation (LTFE) program to evaluate deployed self-contained self-rescuers (SCSRs). The objective of the program is to evaluate how well SCSRs endure the under-ground coal mining environment with regard to both physical damage and aging when they are deployed in accordance with Federal regulations (30 CFR 75.1714). This report presents ?ndings of the combined eighth and ninth phases of the LTFE. For these phases, over four hundred SCSRs were evaluated. The units tested include the CSE SR-100, Draeger Oxy K-Plus, MSA Life-saver 60, and the OCENCO EBA 6.5. The OCENCO M-20 was evaluated only in Phase 9. Testing was per-formed between December 2000 and April 2004. Results of the evaluation indicate that all SCSRs experience some performance degradation due to the mining environment. Observed degrada-tion varies from elevated levels of carbon dioxide, high breathing resistance, and reduced capacity. Mechanical degradation to the SCSR components included breathing hoses, chemical beds, outer cases and seals. The LTFE tests discussed in this report are different from tests performed for SCSR certi?cation to the requirements of 42 Code of Federal Regulations, Part 84 (42 CFR, Part 84). LTFE tests reported here are conducted to an end point, oxygen depletion, to enable comparison of the duration of new and deployed SCSRs. The method for obtaining deployed SCSRs for this evalua-tion was not a random selection from the deployed population of SCSRs. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the generalizability of the results. This program will be implemented following completion of Phase 10 of the current LTFE protocol.

Jan 10, 2006

By Berenice B. Mitchell

THE STATISTICAL tables in this chapter present, country by country, the mineral production of the world in 1949-50. The figures are on a mine basis, unless otherwise indicated, except for cement, coke, and steel, which are measured at the processing plant. The tables are essentially a retabulation, by countries, of the 53 commodity world tables appearing in the various chapters of this volume. For lack of comprehensive information, data for the following minerals are excluded: Andalusite, aplite, asphalt, boron, bromine, calcite (optical), calcium chloride (natural), carbon dioxide, clay, columbium (niobium), diatomite (kieselguhr), dumortierite, emery, garnet (abrasive), gem stones (other than diamonds), germanium, greensand, grindstones, helium, indium, iodine, kyanite, lithium, magnesium compounds (other than magnesite), meerschaum, mineral pigments, monazite, natural gas, natural gasoline, oil shale, olivine, perlite, pumice, quartz crystal, radium, sand and gravel, selenium, sillimanite, sodium salts (other than common salt), stone, strontium, sulfur (byproduct), tantalum, tellurium, thallium, topaz (industrial), tripoli) uranium, vermiculite, wollastonite, and zirconium. In addition, a few minor geographic areas for which no statistics are available, are also omitted from the tabulation; it is believed that no significant quantities of minerals are mined in any of these areas. The statistics in these tables were derived principally from questionnaires sent, in cooperation with the United States Department of State, to the governments of each country. Supplementary sources were United States consular reports, the Imperial Institute's Statistical Summary of the Mineral Industry of the British Commonwealth and Foreign Countries, other official publications of various countries, the United Nations Statistical Yearbook, the Year Book of the American Bureau of Metal Statistics, Minerais et Metaux, business magazines, and company reports. Where official data were not available, esti-

Jan 1, 1953

By Steven J. Schatzel, Joseph Cervik, Gerald L. Finfinger

Gas drainage through surface bore¬holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwal..ls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole inter¬cepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain¬age during longwall mining will be essen¬tial for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European tech¬niques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

This paper describes a U.S. Bureau of Mines investigation of large-scale coal dust explosions in an experimental mine using a high speed electro pneumatic mechanism for the rapid grab-sampling of gases and dusts. This technique enables the monitoring of pyrolysis and charring in fuel dust particles, and the collection of gaseous combustion products, in both large and small-scale explosions. Data obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Test facility show the following: Rapid sampling appears to "freeze" the burned gas compositions at the flame temperature values. Gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen. The particles collected in the flame zone show signs of extensive pyrolysis and charring. Measurements of gas concentrations and particle flame temperatures suggest that char burning may have occurred in the flame zone.

By A. D. Mah

To assist Bureau of Mines research in extractive metallurgy and to add to the thermodynamic data base useful to others, energy calculations were made for 63 reactions relating to investigations on the production of anhydrous aluminum chloride from chlorination of clay.

Jan 1, 1982

By C. E. Reistle

[In producing crude oils of paraffin base and of mixed base the producer is often confronted with the problem of preventing and removing paraffin that settles out of oil and accumulates in the well. This paraffin consists of heavy waxes with some sand and asphalt, and varies in. consistency from a soft semifluid wax to hard gummy wax. This problem is by no means a new one as troubles have been encountered with it since the earliest days of the industry. However, with the discovery of the panhandle, Texas, field and other large fields in which extensive troubles have been encountered, the problem has assumed added importance. In new fields the most serious trouble with paraffin is in the flowing wells the paraffin accumulates in the casing and tubing of such wells and unless removed will completely plug the well. This condition also develops in wells which are produced by gas lift, and often presents a serious problem when, this method of producing the oil is used. In older fields paraffin is also deposited on the face of the producing sand that on the walls of the hale or within the interstices of the sand near the hole, and this materially affects the amount of oil that can enter the well.]

Jan 1, 1927

By J. C. Nigro

Hematite-to-magnetite reduction kinetics were investigated mainly in CO-CO2 atmospheres at temperatures ranging from 500° to 1,000° C. Reduction rates were measured with a thermobalance, which recorded the weight loss as the specimen was reduced. Reduction data on both synthetic and natural hematite spheres showed good linearity of ro [1-(1-R)1/3] with time, t, up to over 85 pct conversion to magnetite; the rate coefficient (k[L], cm/min) obtained from the linear portion of the plot was used to characterize the penetration rate of the hematite-magnetite interface. Gas composition, porosity, and silica content were major factors affecting the rate. Temperature dependency of the reaction rate was small, yielding a mean activation energy of about 3 kcal/mole. Silica additions increased the reaction rate, probably through an increase in the effective surface area and diffusion; however, above 900° C, silica can react to form fayalite. Experimental data showed that the linear thickening rate of the magnetite layer, normally evidence of a chemically controlled reaction, can also be indicative of a reaction controlled by both mass transfer and diffusion. Evidence from this study indicates that the dominant rate-controlling factor in the reduction of hematite to magnetite at high temperatures is transport in the gas phase.

Jan 1, 1973

By R. E. Morgan, J. F. Barkley

"INTRODUCTION In city smoke-abatement work it is customary to require approval of the sizing of fuel-burning equipment. This is to insure that, with reasonable attention, the equipment can be operated essentially smokelessly, having such features as ample furnace volume and air supply. To answer the many inquiries that come to the Bureau of Mines as to what dimensions are acceptable and standard, the requirements of a number of smoke-abatement ordinances have been tabulated.CONCLUSIONSStudy of these tabulations shows that even after many years of fuel-burning practice and experience there is no common standard. Variations in the requirements for the same type of equipment under the same conditions of operation are great. This causes considerable difference in installation costs. Over-all costs being affected, the competitive positions of different types of fuel-burning equipment are also affected. It is apparent that there is a lack of information as to proper dimensions that is commonly accepted as authoritative.DISCUSSIONTable 1 gives the minimum furnace-setting heights required by various cities for mechanical underfeed stokers installed under H.R.T. boilers. Figure 1 shows a typical installation. The dimension given for each case is the distance from the dead plate of the stoker to bottom of boiler shell, unless otherwise noted. As shown in the table, different cities use different size-classification systems; it is not possible to make complete, exact, direct comparisons. Table la gives a comparison for various cities, showing the approximate percentage difference in H.R.T. furnace-setting heights required from those recommended by the Stoker Manufacturers' Association arbitrarily chosen to serve as a basis of comparison. The percentages are approxi¬mate because they were calculated as if all heights as given were measured from the dead plate of the stoker. In two cases a lower height is permitted, in a number of cases the height may be the same, and in a number of cases the height must be greater. The percentage increase goes to 100 in one case. Lack of uniformity is quite evident."

Mar 1, 1950

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U .S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed ?mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1965

By Albert W. Deurbrouck

This Bureau of Mines report describes the washability characteristics of 13 coalbed samples collected in Colorado. Such data are needed to evaluate the quality of the coals of the West, where most of our low-sulfur-content coal reserves are found. Of the 13 samples included in this report, 11 had a total sulfur content of 1 percent or less. All of the samples contained low percentages of ash or could be readily washed to a desirable ash level with minimal loss of yield. The coals ranged in rank from high-volatile A bituminous to subbituminous B; nine of the samples were high-volatile C bituminous. The coalbeds ranged in thickness from 6 to 26 feet; the average was about 8 feet.

Jan 1, 1970

In the U.S. coal mining industry, a large cohort of miners is at or nearing retirement age. As these miners retire, there will be a need to hire and train thousands of new and most likely younger workers. Moreover, a large portion of safety trainers will also require replacement due to retirement. In a speech before the U.S. House of Representatives (2004), Bruce Watzman, Vice President for Safety, Health and Human Resources for the National Mining Association said, “[W]e will need to replace a major portion, approximately 50%, of the underground coal mining workforce within the next 5–7 years.” The large influx of new mine workers, along with the deficit in safety trainers, creates the challenge to provide consistent and effective safety training. Given the expected high turnover of the mining workforce, it is very likely that incoming workers will have much less experience than those leaving the workforce. Unfortunately, inexperienced miners have been shown to incur the highest rate of injuries. The piece of machinery most associated with these injuries is the roof bolting machine, which accounts for 56% of machinery-related injuries in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) has released a new report entitled “Roof Bolting Machine Operators Skills Training for a Walk-Thru Roof Bolter: Trainer’s Guide” (IC 9489). It is designed to help safety trainers develop struc-tured training for new operators of walk-thru bolting machines. This resource will help trainees learn, understand, and apply knowledge and skills. Included in the trainer’s guide are the following tools: [ ] a six-part DVD video series, a skills check survey, talking points, and a complete job training analysis. Also included is an exercise to help trainees learn more about their mine’s roof control plan, as well as a list of supplemental training and reading materials. On-site trainers can modify this guide to fit their particular mine conditions, machines and equipment, and work procedures. The goal of every coal mine safety professional is to increase safety awareness and make mines a safer place to work. The Walk-Thru Bolting Machine Trainer’s Guide will help teach new miners skills to create a safer working environment that will ultimately prevent or reduce on-the-job injuries. Safety trainers can also use the ideas and concepts from this guide to develop their own training skills for the safe operation of other pieces of underground coal mining equipment.

Jan 6, 2007

By Jennifer A. Slatnick

The U.S. Bureau of Mines estimated the potential availability of titanium from 39 mines and deposits in 12 market economy countries. The evaluated properties account for 76 pet of the market economy country demonstrated resources, which total 603 Mt of contained titanium dioxide (Ti02) in the minerals rutile, ilmenite, leucoxene, and anatase, and represent 95 pct of current production. Approximately 250 Mt of contained Ti02 could be economically recovered from evaluated titanium operations at January 1992 market prices. In terms of mineral concentrates, this equals approximately 19 Mt of rutile concentrate, 110 Mt of ilmenite concentrate, 47 Mt of synthetic rutile concentrate (in addition to the ilmenite), and 160 Mt of titanium slag that could be recovered. Over the past decade, the titanium minerals industry has adapted to the changing market. In the 1980's, titanium producers expanded production because of the rising demand for titanium products. Today, the titanium industry is in a state of overcapacity, and byproduct revenues, such as that from zircon, have become essential in keeping operations profitable. The industry has also witnessed a greater dependence on upgraded ilmenite products, such as titanium slag and synthetic rutile, because of the expense of rutile and the lower wastes emitted from these upgraded products. As a result of this dependence on upgraded ilmenite products, South Africa has become a leading titanium producing country and has displaced Australian production.

Jan 1, 1994

By James P. Bennett

To improve construction materials for emerging chemical and metallurgical technologies, the Bureau of Mines is investigating the acid resistance of ceramic materials. In the study described here, eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed to 20 wt-pct HC1 at 50° C for 110 days. The test apparatus designed to evaluate the materials is described. Changes in chemical and mineralogical composition, cold crushing strength, volume, and weight, and leach rates of AI, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. In general, the statistically significant physical property changes that occurred were small. In many cases, no changes were detected.

Jan 1, 1982

By J. H. Maysilles

The Bureau of Mines, U.S. Department of the Interior, is investigating several types of low-grade uranium deposits. Projections indicate that an increased percentage of future production will be derived from such sources. One material studied was from the Coso Mountains of California; this material contained 0.04 to 0.12 percent U3O8. The deposit contains at least two distinct types of mineralization. The material representing the bulk of this deposit was amenable to acid leaching; 80 to 85 percent U308 extraction resulted from leaching with 20 to 40 pounds per ton of sulfuric acid. No oxidizing agent was required. This ore fraction could be treated by either agitation or percolation leaching. Uranium recovery and purification from the acid leach solution was accomplished using anion exchange followed by precipitation with hydrogen peroxide and ammonia. The second type of mineral was very refractory to acid leaching; a maximum extraction of only 44 percent was obtained with sulfuric acid. Nitric and hydrochloric acids were ineffective also.

Jan 1, 1978

By Elaine T. Cullen, Albert H. Fein

Federal law mandates that all miners receive safety and health training when first entering the mining industry and at least 8 hours annually thereafter. Although the mining industry has historically relied on an experiential master-apprentice model for training new employees, the formal safety training provided to miners is generally done in a classroom, with mixed results. In a series of stakeholder meetings held by NIOSH across the West in 1997-2000, trainers identified significant gaps in materials that were available to teach new and experienced miners. They asked whether NIOSH could develop effective materials to fill these perceived gaps, as well as make training more effective for those who were required to attend, but who often refused to be attentive. Adult learning theories, social learning theories, mentoring, and storytelling were all employed in the development of a series of safety training videos that have become very popular in the mining industry. This Report of Investigations describes the theoretical frameworks that were used, the process that was developed to produce the videos, and the results of the evaluations as to whether or not they were effective in training new and experienced miners.

Jan 8, 2005