Search Documents

By J. E. Pahlman

As part of its goal to minimize the requirements for mineral commodities through conservation and substitution, the Bureau of Mines is conducting research to determine the resistance of alumina refractories to corrosion by alkali-containing slags that could result from burning of the abundant Western lignites in metallurgical operations. Static corrosion tests were performed at 1,000° to 1,350° C and dynamic tests were performed at 1,400° to 1,600° C to investigate the stability of refractory specimens in slag environments. In general, the degree of refractory attack increased with decreasing alumina content in the refractory and with increasing alkali content of the lignite ash. The parabolic kinetics observed in static tests suggested that a reaction product layer is formed through which ionic diffusion must occur to sustain the reaction with the refractory material. The linear kinetics observed in dynamic tests in high-viscosity slags indicated a shearing of the reaction product layer by viscous slags. The observed lesser attack of refractories by low-viscosity slags can be explained on this basis. Two 99-percent-alumina refractories and two 90-percent-alumina refractories formed an expanded protective layer with the more viscous slags but not with the less viscous slags. Corrosion of 90-percent-alumina refractories increased exponentially with temperature. In refractories with the same nominal alumina content, those that contain a combination of a-Al203 and mullite (3A1203?2Si02) have better corrosion resistance than those containing a combination of a-Al203, cristobalite (Si02 mineral), and mullite. In alkali environments (1,300 to 1,400° C), 90-to 99-percent-alumina refractories are recommended for use as furnace linings.

Jan 1, 1980

By M. M. Tilman

The Bureau of Mines conducted research to determine whether it is possible to substantially improve the fatigue resistance of lead sheet by means of surface coatings. Five types of coatings were applied to unalloyed chemical lead sheet. Flexural tests revealed that the best fatigue resistance was obtained with coatings of vacuum grease. Vacuum-grease coatings on unalloyed lead sheet resulted in fatigue resistance at least as good as that of the fatigue-resistant alloy Pb-0.04 Ca. Coated lead sheet was also tested in short-time tensile tests and in tensile creep tests. Tensile and yield strengths were increased by several of the coatings with only moderate loss of ductility. Creep resistance was also improved in varying degrees by most of the coatings. The Bureau also conducted research on the effectiveness of noise barriers by using sheet lead in combination with other materials. Noise barriers consisting of continuous-cast sheet lead with gypsum board were found to be effective and relatively inexpensive barriers.

Jan 1, 1978

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the non-condensable gases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of Gases produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills. The study required a complete extraction of all the hydrogen sulphide from the gas stream after it left the water-cooled distillate condensers and before the gas stream entered the charcoal absorber for removing the light naphtha. In devising the method it was necessary to take into account a constant variation of velocity, pressure, and percentage of sulphide in the total gas stream coming from the still. Ordinarily, the quantitative determination of hydrogen sulphide in gas is made by analyzing small samples taken at regular intervals. This estimation can be accomplished by use of the Bunts gas burette as modified by Tutriler, or by a similar method. In the industries where the flow of gas is constant and of uniform composition, this practice is sufficiently accurate for plant control. For experimental work where many variables have to be taken into consideration, as in the case at band; these methods are not applicable.

Jan 1, 1931

By David R. Hanson

Experimental work performed by the Bureau of Mines in a laboratory environment has shown that the formation of failure zones within certain rock types is accompanied by the emission of significant amounts of radiofrequency (RF) electromagnetic (EM) energy. This radiation was detected using nonresonant, "electrically short," broad-band antennas. Rock types for which emission was observed include granite, quartzite, and taconite; sandstone and marble did not emit measurable radiation. Amplitude spectra of the radiation showed the energy to be concentrated between 10 and 40 kilohertz. These data indicate that emission is directional, but this has not yet been proven. In addition, amplitude of RF emission increases with increasing crack size. Since emission was observed only for brittle quartz-bearing rocks, it appears the formation of piezoelectric fields is a necessary condition for RF radiation. Plausible mechanisms for emission include rapid decay of piezoelectric fields accompanying the sudden stress release at failure and/or the acceleration of an "exoelectron plasma" through the intense local piezoelectric fields. Since emission appears to increase with the scale of failure, and since antennas do not need to be coupled directly to rock surfaces as with conventional geophones, the possibility of developing a portable system to monitor seismically active areas exists.

Jan 1, 1981

By Wesley A. Grosh

The Vest nickel prospect, in Floyd County, Va., was discovered about 25 years ago. Limited exploration of the deposit had indicated some appreciable nickel mineralization in the sulfide ore. The property was examined on March 9, 1943, by an engineer of the Bureau of Mines in company with C. W. Vest, owner of the property. A limited exploration program was recommended. Two holes totaling 320 feet were diamond-drilled in January 1944. Drilling indicated the sulfides are sparsely disseminated. The only nickel values of interest were at the old prospect shaft.

Jan 1, 1949

By Franxis Church Lincoln

"INTRODUCTION During September 1944, the Bureau of Mines undertook a program of investigation and limited exploratory drilling at the Last Chance mine, near the village of Arthur in Grant County, Wisconsin, as part of a general investigation of the zinc-producing area of southwestern Wisconsin when every effort was being made to increase the production of metals important to the Nation's war program.The Bureau's attention was directed, to the Last Chance mine when the operators discovered high percentages of zinc in an exploratory churn drill hole a short distance southeast of the mine. The ore was found in the Trenton Limestone, which underlies the ore horizon then being mined. To determine whether this discovery was important, and to demonstrate the possible extension of the ore the Bureau of Mines drilled five additional holes in the vicinity of the discovery.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report."

Mar 1, 1947

By Fredrick L. Johnson

No mineral resources were delineated during our investigation of the Antelope Wilderness Study Area (WSA). Only a few claims have been located in the area and only four workings were found. There has been, however, considerable exploration and mining activity in and near the south end of the study area. The Morey mining district, just southeast of the WSA, produced silver, and lesser amounts of gold and lead, sporadically from the mid-1860's through the mid-1960's. Long Lac Mineral Exploration (Texas), Inc. is actively exploring a large block of claims for hot-spring type, low-grade, large-tonnage gold deposits. Their claim block extends into the study area. The WSA, located midway between Tonopah and Eureka, encompasses approximately 87,400 acres. It is underlain by Tertiary rhyolitic and latitic volcanic rocks and by Paleozoic sedimentary rocks. At least three areas in the Paleozoic rocks have many of the favorable criterion for hot-spring type gold deposits; they have been faulted, silicified, brecciated, and hydrothermally altered, and have anomalous concentrations of precious metals and pathfinder elements. With additional exploration in the south part of the Antelope WSA, gold resources may be discovered.

Jan 1, 1986

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines lid some development drilling at the Milan deposit in an endeavor to find an additional source of supply of copper. The deposit, which is in Coos County, northern New Hampshire, is about 8 miles northwest of Berlin. It was discovered in the seventies and was worked steadily until 1886, yielding a monthly production of 2,600 tons of ore. Lessees opened the mine again in 1695 and mined 1,500 tons. The Milan Mining & Milling Co. acquired the property in 1907 and made regular shipments of ore and concentrates until 1910. From 1911 until 1938, the tract was held by a local resident for timber land, Ventures, Limited, a mining concern with headquarters at 25 King Street, West, Toronto, Canada, acquired the property in 1938. No production has been recorded since 1910. To cut the vein below the old mine workings and to search for extensions to the northeast and southwest, the Bureau of Mines diamond-drilled eight holes for an aggregate of 3,596.2 feet.

Jan 1, 1950

By R. V. Ramani, R. Bhaskar

"One of the primary means of control of health hazards from respirable contaminants in mine atmospheres is through design and operation of mines to meet mine health and safety regulations and recommended practices. A U.S. National Academy of Sciences study concluded that for significant progress in coal mine dust control, research should be directed more toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust. Theoretical and experimental studies on transport of dust · in mine airways, particularly coordinated efforts to validate theory with practice, are scarce. Some empirical models, developed on the basis of experimental data, are available but these models cannot be applied to new conditions. The purpose of this paper is to present the results of theoretical and experimental studies on the transport and deposition of dust in mine airways. This study is a part of an ongoing research project in the Generic Mineral Technology Center on Respirable Dust.In the paper, the assumptions of the modeling phase of the project and the development of a convectiondiffusion equation for dust transport in mine airways are outlined. The important aspect of the modeling effort is the capture of the deposition phenomenon. The experiments performed under controlled conditions in a typical mine airway, as well as under normal mine operating conditions, are discussed. The comparison of the model predictions with experimental results are made to identify critical areas of agreements and deviations. The implications of the findings and areas for further research and development are presented."

Jan 1, 1990

"The major thrust of this research is directed towards a better undstanding of the behavior of airborne dust particles in underground mine airways. Figure 61 shows a schematic of dust flow in mine airway. The work included development of a mathematical model of dust behavior in mine airways, experimental study of the behavior of dust clouds and comparison of computer model output and experimental results. Re-entraiment is a secondary source of dust in mine airways and factors affecting re-entrainment are being identified.Investigations have encompassed both experimental and theoretical research into the behavior of dust in mine airways. Experiments were performed in mine airways under both controlled and normal operating conditions (Figure 62). The controlled experiments included the documentation of the concentration and desposition patterns for two types of dust under three different velocities. Real-time dust concentration data were obtained using real-time aerosol monitors (RAM-1) (Figure 63).On the theoretical front, a convection-diffusion model of the dust flow phenomenon in mine airways was developed considering dominant mechanisms affecting dust transport and deposition in mine airways. Mechanisms modeled include turbulent and gravitational deposition, coagulation, and dispersion. Comparative analyses of results of the controlled experiments with the predictions of the mathematical model were carried out. In addition to the overall validity, the adequacy of the individual components of the model, such as deposition in the total and respirable range, and dispersion were examined in light of the experimental observations."

Nov 1, 1988

By Sara J. Davenport

Hydrogen sulfite has been listed (1)3/ as a possible hazard in 50 occupations, many of which are in the mineral industries. The effects of its occurrence in the petroleum industry made themselves felt more than two decades ago, resulting in a comprehensive study (2) of the toxic gases from Mexican and other high-sulfur petroleum products. The mining industry, likewise, has had cause to guard against this gas. Enough hydrogen sulfide has been found in coal and some noncoal mines during normal operations to cause severe eye irritation, some serious illness, end even fatalities. It is usually a product of the decomposition of sulfur compounds and may be produced by burning explosives containing sulfur; the gas in harmful qauntities is formed by the use of block blasting powder or by the use of dynamite in blasting sulfide ores. Hydrogen sulfide is readily soluble in water, and enough may be released from water streams in coal and noncoal mining to cause fatal poisoning it is found sometimes in stagnant water underground, particularly where ventilation currents are absent, and great care must be exercised when accumulations of such waters are disturbed, as exposure to comparatively low concentrations of the gas evolved therefrom has caused fatal accidents.

Jan 1, 1945

By McHenry Mosier

The Bell mine operated by the Warner Co. at Bellefonte, Pa., has an annual production of about 600,000 short tons of high-grade limestone. Since 1924, shrinkage stoping has been the mining method. Horizontal, long-hole diamond-drilling for production in stopes was started with one machine in July 1946. It is now standard practice. The burden on the holes is 10 feet. Diamond bits are noncoring EX-size in both concave and pilot types. The two types have little difference in drilling speed at the Bell mine. The diamond drills are mounted on 3-inch single-screw columns. Diamond drilling shows a marked increase in efficiency at the Bell mine, compared to percussion drilling, with respect to tons broken per drill shift, tons broken per foot of hole, and tons broken per pound of explosive. The advantages of diamond-drilling blast-holes also include (a) improved safety, greater footage per drill shift, (c) better frag- mentation of the broken, stone, and (d) reduction in amount of barring down required in stopes because the working places are limited to slots which have a relatively small area.

Feb 1, 1948

By David Ingram

The results from the sound level measurements, the dosimeter recordings and the time-activity studies on four different air-rotary rigs indicate a wide variation of operator noise exposure during hole development. These variations appear to be dependent on the cab design and the operator?s drilling behavior. Studies have documented that exposure to high sound levels for long periods of time can cause hearing loss. The results of this study help identify the loudest parts of the drilling cycle. Sound level measurements on the four rigs show that all the rigs generate sound levels that are 90 A-weighted decibels (dB(A)) and above within 6 feet around the rigs during drilling. It is easy to conclude that some type of noise protection, such as a cab, is needed to protect the operator from overexposure to noise for an eight-hour shift of uninterrupted drilling. However, even when rigs are outfitted with cabs, operators observed in this study are being exposed to sound levels above 90 dB(A) during some activities required to complete a drilling cycle. An evaluation and comparison of the four dosimeter recordings and time-activity studies during one drilling cycle may explain why variations in operator exposure occur. Table 1 summarizes the time-weighted average (TWA) and accumulated dose percentages for each of the four operators during the time needed to complete one typical hole cycle.

Jan 1, 2008

By R. O. Pynnonen

Tunnel-driving is recognized as a hazardous occupation; adequate support of roof and sides for preventing accidents from falling material is usually one of the most important safety problems. Where extraordinary conditions of sand and water are found, this problem becomes even more difficult. Tunneling at the Tioga No.2 mine was stopped when a 22-foot bed of water-saturated, fine gray sand was encountered. The tunnel, designed to house an ore-conveyor belt, was being driven from both ends. Driving was extremely difficult at both the upper and lower faces when the sand horizon was reached. A distance of 178 feet remained between the faces. Heavy pressures deformed the steel-supporting rings at the upper face, and there was an inrush of mud and sand at the lower face.

Jan 1, 1958

By L. Cheng, M. S. Seehra, P. S. Raghoottama

The four major IR bands of a-quartz at 1080, 797, 693 and 488 cm-1 are studied at room temperature by FTIR-Photoacoustic Spectroscopy. Using Rosencwaig-Gersho theory, equations for the PAS signal q for the thermally thin and thermally thick cases are derived and it is shown how thin to thick transition occurs and leads to saturation as the sample mass is increased. For sample mass < 2 mg, q is proportional to sample mass thus defining the region for quantitative analysis. The dependence of q on the chopping frequency f is found to vary as q f-n with n ? 0.9 for quartz, in good agreement with the RG theory.

Jan 1, 1989

By K. R. Van Doren

The polynomial method for estimating virial coefficients from experimental data suffers from three serious defects: (1) There is no known relationship between the polynomial coefficients and the virial coefficients, (2) the values of the estimates depend upon the degree of the polynomial and the particular set of values used for the independent variable, as well as the random errors in the dependent variable, and (3) the variances calculated for the estimates do not represent the mean square errors of estimation. Attempts to overcome these defects have thus far been unsuccessful; these attempts have also failed to account for the fact that none of the virial coefficients are uniquely determined by the values of the dependent variable for a finite set of values of the independent variable. The conclusion is that virial coefficients cannot be reliably estimated from experimental data unless additional information about the virial expansion itself, such as its rate of convergence, is available.

Jan 1, 1969

By Marcia L. Harris

The National Institute for Occupational Safety and Health (NIOSH), as part of its continuing research program for evaluating coal dust explosion hazards, has investigated several areas in which current practices may need to be updated in order to adequately protect mines against coal dust propagated explosions. In the United States, current rock dusting requirements remained largely unchanged since 1969. US Title 30 Code of Federal Regulations Section 75.403 is based on a coal dust particle size survey performed in the 1920s and later was supplemented by full-scale testing of the rock dust ability to inert a coal dust explosion. NIOSH recently conducted a comprehensive survey of US underground coal mines to determine the range of coal particle sizes found in dust samples collected from the mine entries. Due to advancements in technology and modern coal mining techniques, the current coal dust particles in intake airways are significantly finer than those found in the mines in the 1920s. According to past full-scale dust explosion test results, the current rock dusting practices used in today?s mines to inert a coal dust explosion may not be adequate. Other closely related issues such as rock dust testing methods and sampling procedures are discussed.

Jan 1, 2009

By S. H. Brooks

"IntroductionThis preliminary report deals with the effect of oxygen pressure on the ignition temperature and combustibility of oils, it is the third of a series which will present the results of an investigation being made by the Bureau of Mines, on oxygen-oil explosions. The purpose of this research is to obtain technical data that will serve as a basis for safety precautions general outline of the problem has been given in the first report (Serial 2507).The present experiments have resulted in (1) a method for determining spontaneous ignition points of oils in an atmospheric of oxygen under pressure; and (2) the determination of these ignition temperatures for three typical oils, one being an animal oil (sperm), one a vegetable oil (linseed), and one a mineral oil (""Moiloil A"").These experiments on explosibility of oil were performed in order to discover the general nature of the phenomenon, especially the order of magnitude of the temperature necessary for spontaneous explosion (120°C. and upwards) and the effect of pressure variation (negligible as regards ignition temperature but important in relation to the violence of the explosion). A continuation oftests should provide a basis for selecting the safest lubricants for high pressure compression of gases particularly air and oxygen; and should be of value when devising new specifications for lubricants, both in the government departments and the compressed-gas manufacturing industry."

Dec 1, 1923

By Ronald A. Vary

This paper is one of a series prepared by the United States Bureau of Mines dealing with milling methods and costs. In view of the current revival of interest in gold mining, information dealing with practices and costs in the development of gold properties is apropos. Milling practice at a small gold property in the prospect stage is described where, with a small outlay for plant and equipment, development has been carried on for about 20 months on the proceeds of the mill operation with little additional expenditure. The paper shows about what may be expected as to costs at a small property operated under northern climatic conditions and with rigid economy throughout the plant.

Jan 1, 1931

By C. K. Man

Coal dust explosions are routinely conducted within the full-scale experimental mine at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM) to meet the needs of numerous safety and health research programs. Many of these explosion tests over the years involved igniting different coal dust and limestone rock dust mixtures (up to 80% by volume rock dust). Following four more recent tests, floor dust samples have been collected and analyzed using the alcohol coking test and scanning electron microscopy (SEM) and the results compared to estimate the flame travel.

Jan 1, 2009