Search Documents

By William H. Schiffbauer, William D. Mayercheck, August J. Kwitowski

This report summarizes work sponsored by the Bureau of Mines in the development of a remote operating system (ROS) for controllng a thin-seam continuous miner (TSCM) 500 feet or more distant from the extraction face. Detail s are provided on ROS subsystems including the continuous miner, video equipment, controls and displays, the electronic control system, and the operator station.

To inexpensively monitor the ventilating airflow anywhere in underground working places. The Approach: The Bureau has developed a small self-contained monitor which sounds an audible alarm and energizes a flashing lamp if air velocity decreases below normal. How It Works: The sensing element of this inexpensive monitor is a thermistor, which is self-heated by a constant-current electrical source. Airflow over the thermistor increases heat removal and lowers the thermistor temperature. Since the electrical resistance of a thermistor is a function of temperature change, the voltage across it varies with temperature, and, therefore, the air velocity. Changes in the voltage across the thermistor are amplified, and can be used to trigger the alarms.

Jan 1, 1975

By Michael J. Sapko, Gregory M. Green, Harry C. Verakis, Kenneth L. Cashdollar

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted a joint survey to determine the range of coal particle sizes found in dust samples collected from intake airways of U.S. coal mines. The last comprehensive survey of this type was performed in the 1920’s. The size of the coal dust is relevant to the amount of rock dust required to inert the coal dust, with more rock dust needed to inert finer sizes of coal dust. Dust samples were collected by MSHA inspectors from several mines in each of MSHA’s ten bituminous Coal Mine Health and Safety Districts. Samples were normally collected in several intakes at each mine. The laboratory analysis procedures included acid leaching of the sample to remove the limestone rock dust, sonic sieving to determine the dust size, and low temperature ashing of the sieved fractions to correct for any remaining incombustible matter. The results indicate that particle sizes of mine coal dust in intake airways are finer than those measured in the 1920’s. The significance of these finer coal dust sizes is discussed relevant to the amount of rock dust required to prevent coal dust explosions.

By T. H. Davis

Twelve laboratories from the Western United States and Canada participated in radon progeny intercomparison measurements at the U.S. Bureau of Mines radon calibration facility in March 1987. The participants intercom pared grab-sampling and automated equipment methods at high and low concentrations of radon progeny and condensation nuclei (CN). The objective of this intercomparison was to determine if the measurement procedures and equipment of the North American facilities are equivalent. The sampling results showed good agreement among all participants. The standard deviation for the working level measurements was less than 3.5% for 1.70 working level (WL) and less than 8.8% for 0.21 WL. This relatively good agreement was achieved by using alpha standards calibrated by National Bureau of Standards (NBS) and by closely checking and monitoring airflows.

Jan 1, 1989

By Oleg Terichow

Electrophoretic mobility measurements were made on samples of Florida phosphate slimes to determine the optimum conditions of coagulation and precipitation in aluminum sulfate solutions. The addition of silica sand and other selected materials as mutual coagulants has demonstrated the practicability of coagulating two dissimilar particle systems by elimination of the repulsive double layers. By proper selection of the solution and its concentration, the reduction of the double layer to a zero point of charge causes coagulation and rapid precipitation of both particle systems. Confirmation was found in filtration tests and sedimentation tests.

Jan 1, 1973

By H. C. Ko

As part of the Federal Bureau of Mines effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation, the standard enthalpies of formation of a-magnesium sulfate, a-magnesium sulfate, and magnesium sulfate monohydrate were determined by hydrochloric acid solution calorimetry. The values of the standard enthalpies of formation in kcal per mole at 298.15 K are -307.95 ± 0.13 for a-MgS04, -307.03 ± 0.13 for ß-MgS04, and -384.72 ± 0.13 for MgS04 .H2O.

Jan 1, 1979

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

By John J. Sammarco

Mining, traditionally a low-tech industry, is now utilizing surprisingly complex programmable electronic (PE) systems. The functional safety of PE-based mining systems is an international issue and concern. From 1995 to 2001, there were 11 PE-related mining incidents reported in the U.S. and 71 PE-related mining incidents reported in Australia. These incidents are due, in part, to unprecedented levels of system complexity. The National Institute for Occupational Safety and Health (NIOSH) is addressing this issue of system complexity by conducting research to develop a quantitative complexity assessment methodology based on Normal Accident Theory (NAT). The methodology models the behavioral interactive complexity at the level of system requirements. A graph-theoretical approach is used for creating quantitative metrics from Software Cost Reduction (SCR) dependency graphs. This complexity assessment methodology will help realize simpler, safer systems that will be easier to validate and verify. The methodology will benefit mining and other industries as well.

By Marc T. Filigenzi

Two of the major ground control safety issues confronting underground mine operations today are shaft pillar stability and the failure of rock around active mine openings. Failure of a mine shaft can lead to the entrapment of workers. Failure of rock around active underground mine openings can lead to roof falls, which in turn can result in worker injuries and fatalities. Finite-element analysis has proven to be a reliable method for predicting stresses and displacements around underground mine openings. However, this is a complex and time-consuming technique and is not used as often as it could be in mine planning. The purpose of this paper is to demonstrate one technique developed at the Spokane Research Center that allows the user to create a finite-element model of a two-dimensional section of an underground mine in a relatively straightforward manner. This model is then used to calculate stresses, displacements, and safety factors around mine openings. With this information, mine planers can evaluate the stability of mine openings as well as the stability of pillars and mine shafts. This analysis will help develop mining sequences and layouts that minimize stresses in that section of the mine. This, in turn, should minimize the occurrence of shaft failure, roof falls, and other hazards associated with underground mining.

By Ronald D. Hill, Elmore C. Grim

The goal of blasting is to get maximum fragmentation of the consolidated material in the overburden with optimum drilling and blasting cost. The amount of fragmentation required is determined by the stripping unit to be used In overburden removal. Many coal seams must also be broken by blasting; this is conducted before coal removal. There are environmental factors as well as due regard for public safety, health, and welfare that must be considered in choosing the blasting plan. The blasting plan should be made during preplanning and is based on data from the overburden cores. Analysis of the data will help In determining the kind of drilling equipment and bit types that will be needed for overburden preparation.

Jan 1, 1974

By C. B. Manula, R. L. Sanford, R. A. Rivell

Development of the Rail-Haulage Sub-assembly for the Production Sub-system (UGMHS)* required the use of ,a newly formulated model in order to best satisfy the requirements. Many of the ideas of the former single-stage rail simulator included in the original version of UGMHS have been used, together with the results of experience gained in applying the earlier model to a variety of operating situations (Sanford, 1969). The sub-assembly is developed as an independent system and, as such, can be used to analyze track systems using production distri¬butions as data input. In addition, since this model is designed to replace the original sub-assembly in UGMHS, the linking procedure is identical with respect to bi-directional information flow. The flow of coal from production sections, for example, fills the mine cars, but a condition of "out of empties" or "full of loaded" at a loading station will shut down inby production sections. A requirements analysis was conducted to determine specifically how the model could best serve the user. Operating management had the largest input in developing the following requirements for the Rail Sub-assembly: a) data input in mixed narrative - numeric form to permit user identification of the input variables; b) a user option to extract several ranges of detail in model output, i.e., an average shift summary of minimum retrieval

Jan 1, 1974

By C. M. K. Boldt, R. L. Levens, A. D. Marcy

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface are aexposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 1995

The generally disappointing results obtained in the present study, together with the high material costs involved, preclude any general recommendation for a continuation of the work. One recommendation arises, however, from some observations on the application of latex to spoil banks. It was found that dilute latex used on a slope of spoil bank material at an application rate of 400 lbs per acre (dry basis) stabilized the soil and made it much more resistant to washout by rainfall. It is recommended that a study be conducted to use latex for temporary stabilization and/or sealing of spoil banks before and during reclamation procedures, on coal slurry ponds and coal refuse piles.

Jan 1, 1972

By R. V. Ramani, P. M. T. White, D. Sutton

6.1 Summary This report deals with the investigation carried out to select, test, and implement a method of evaluating coal deposits and reserves. Cognizance is taken of the inherent characteristics of coal and the legislation covering aspects of health, safety, environment, and ecology applicable to the coal mining industry. Further, the method is computerized and provides information that is meaningful and readily available to other programs and sub¬systems within the concept of the Master Design Simulator. The Geology and Reserves Sub-system interface with the total system is provided by a geological data library which is structured to hold and make accessible all the data required by the system. The output from the program is accurate and useful to users with a wide variety of computer experience, knowledge, hardware and storage capacity. The sub-system is designed to function as a separate unit or an integral part of the total system and, there¬fore, an interface to or with the system has been established. The work carried out by the sub-system includes: (a) The analysis of raw geological data. This involves:

Jan 1, 1974

By J. Whyatt

A package of bench design programs is being publicly released by the National Institute for Occupational Safety and Health (NIOSH). These programs are designed to provide a probabilistic estimate of the likelihood that various widths of catch bench will be retained. Program modules address the mechanisms of plane, plane step path, and wedge failure. Results are drawn from statistical and geostatistical descriptions of fracture characteristics and other input parameters, and reported as the statistical chance that a given width of catch bench will survive, that is, that a catch bench will remain wide enough to catch rolling and sliding material and prevent such material from posing hazards to miners operating below. The capabilities and application of this software are demonstrated through a case example. Comparing bench width estimates obtained using geologic data with actual widths is a key step in verifying that a program is appropriate for particular site conditions and that proper statistical descriptions of fracture parameters for that site have been developed. Such verification efforts improve confidence, and hence usefulness, of this method for designing future slope benches. Development and release of these programs appears particularly timely given recent progress in photoanalysis methods, which promise to greatly reduce the cost of collecting fracture data.

Jan 1, 2004

By Russell C. Frith, David C. Oyler, Dolinar Dennis R., Christopher Mark

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures. To help determine what factors contribute to such failures, a comprehensive international database of 131 case histories has been compiled. The cases include six failures where major rock falls occurred in front of the shields, and seven even more serious failures involving major overburden weighting. The case studies suggest two types of room failure mechanism. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender or remnant longwall panel narrows. The second is an overburden weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rockwell above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used. Weighting failures were not greatly affected by the density of roof reinforcement. In one of the overburden weighting cases, in a Pittsburgh coal bed mine, stress cell, convergence, bolt load and extensometer data have been used to analyze the failure in detail. Key words: coal mining, ground control, longwall, recovery room.

By Stephen P. Signer

This paper presents an overview of laboratory and field tests on approximately 250 fully grouted roof bolts instrumented with strain gauges in order to study loading behavior. Laboratory work included pull tests, time-dependent tests, and shear tests. The field tests were conducted in 14 different mines extracting different commodities. However, because of the focus of this publication, only the results of tests in 9 coal mines are reported here. In the field tests, all but 14 bolts were loaded by rock movement; these 14 bolts were tested using pull gear. The variables studied included anchorage length, mechanical interlock, time-dependent behavior, shear, installation load, loading rate, and maximum load level. Such information will improve the understanding of the behavior of resin-grouted bolts, which in return will enhance the safety of miners by reducing the occurrence of rock falls. The influences of geology, overburden depth, entry width, mining-induced stresses, and bolt spacing are not described.

Jan 10, 2000

By R. V. Ramani, C. B. Manula, A. Owili-Eger

Recently, a collection of programs that will simulate a ventila¬tion system with extensive analyses and report-generating capabilities and error diagnostics has been developed (Didyk, 1974). It has pro¬visions to handle air injections, methane or gas emissions, and leakage. Additionally, it will solve problems where fixed and/or maximum air quantities are specified for some airways. Finally, the simulator has been structured to be extremely modular so that additions and revisions to the model can be easily made. The general aspects of the information flow and logical structure of the mine ventilation simulator are shown in Figure 14. The output from the methane emission model is input into the ventilation simulator for calculation of the concentrations in all branches of the network. The methane model and the ventilation simulator provide powerful tools for the analysis and planning of mine ventilation systems. INPUT DATA REQUIREMENTS In all of the mathematical models, several coefficients that de¬fine the characteristics of the ventilation system are used. For the ventilation simulator, these include the frictional characteristics of the ventilation regulatory devices. Considerable work has been done on the experimental determination of these coefficients for smooth pipes and well-defined mediums, but only limited data are available for actual mining conditions. FRICTION FACTORS: The frictional characteristics of mine airways affect both the dispersion of pollutants and air flow through the roadways,. They

Jan 1, 1975

By James R. Aggson

The theoretical relationships that are used to calculate in situ rock stress magnitudes and directions from borehole deformation data obtained during overcoring are based on the assumption that the rock is a linearly elastic material. Strictly speaking, this assumption is not valid in any rock. Thus, investigators using overcoring techniques must either accept various degrees of nonlinearity and the associated inaccuracies or use core testing techniques that address the problem and compensate for elastic nonlinearity. Previously developed test procedures for stress-relief overcores partially correct for nonlinearity. This Bureau of Mines paper describes a test procedure that completely corrects for elastic nonlinearity in stress-relief overcores.

Jan 1, 1977

By David J. Ellis

The mineral industry of Benin continued to be confined to the production of cement, crude oil, salt, and sand and gravel. Only crude oil and cement were exported, with the value of crude oil exports and cement exports constituting about 20% and 2% of export revenue, respectively. The value of crude oil exports was less than the cost of imports of refined petroleum products. Production of crude oil was unchanged from 1986, averaging 5,500 barrels per day (bbl/d). The Government managed the facilities at the Semé Oilfield while actively seeking a new manager to replace Pan Ocean Oil Co. of Switzerland, whose contract was canceled in 1986. Recoverable reserves of crude oil were estimated to be between 18 and 30 million barrels.

Jan 1, 1989