Search Documents

By M. C. J. van der Merwe

"Carboxymethyl cellulose is an organic binder used in the iron ore pelletizing industry. The basic principles of how carboxymethyl cellulose (CMC) solutions behave during the pelletizing process and how these principles affect the drop and compression strengths of the pellets are poorly understood. The aim of the investigation was therefore to gain knowledge on the behaviour of CMC during the pelletizing of haematite concentrate.Haematite pellets with different additions of CMC (0.1–0.4 wt%), were subjected to drop tests, compression tests, and free moisture content analysis. The relationship between the drop strength, compression strength, free moisture content, elapsed time, and CMC concentration was analysed.The drop strength had a strong correlation with the free moisture content of the haematite pellets, with a correlation coefficient of 0.94. The compression strength of the CMC-bonded haematite pellets increased as the free moisture content decreased, reaching a maximum upon depletion of the free moisture content. Haematite pellets with CMC concentrations of 0.1 and 0.2 wt% developed most of their strength within the first day after pelletizing, whereas pellets with concentrations of 0.3 and 0.4 wt% developed most of their strength between one and two days after pelletizing. The time within which CMC-bonded haematite pellets develop most of their strength is therefore dependent on the CMC concentration. IntroductionFines are produced during the beneficiation of iron ore. These fines are separated from the lump ore and can be upgraded to produce a concentrate, which is used as a raw material for the production of pellets. Pellets in turn form a key burden material for direct reduction processes as well as the blast furnace (Zhu et al., 2015).Inorganic binders such as bentonite have been used predominantly in the iron ore pelletizing process to obtain pellets with suitable properties (Eisele and Kawatra, 2003). These binders, however, have the disadvantage of introducing impurities into the pellets. This has resulted in organic binders being pursued as suitable replacements for inorganic binders, of which carboxymethyl cellulose (CMC) shows good potential. Although CMC has been used as an organic binder in iron ore pelletizing, the fundamental principles of how it behaves during pelletizing and how these impact on pellet properties are poorly understood."

Jan 1, 2017

[Consider a square block W in an ore body S2, to be valued from one centre sample w, and one corner sample w2 (Fig. 9.1). The sample set is ws = Iw,;w21. We can estimate the block average µw by the average of the sample values x, and x2: µw = 'z (x, + xz). (9.1) The error made is measured by the estimation variance: o' (ws to W) = 2 - (ws; W) - - (ws;ws) - - (W; W). (9.2) However, we know that the centre sample w, gives more information about the block value than the corner sample w2. In the example studied in § 8.4, where w, and w2 were considered to be points, we found that of (w, to W) was nearly one third smaller than o2E (w2 to W), therefore when estimating W one should give more weight to w, than to w2. In general, when evaluating a block W from a set of n samples ws, where WS = l w;w2; ... wn1, a better estimator of µw can be obtained if we give different weights to the sample values, depending on the size and the positions of the samples. Some desirable properties of such an estimator µw are: ? It should be a linear function of the sample values xi: n µw = bi xi (9.3) =t where bi = weight given to sample x . ? It should be unbiased, i.e. its expected value should be equal to the true block value: E [µw - µw] = 0. (9.4) ? The mean squared error of estimation of µw should be a minimum E [(µw - µw)2] = a minimum. (9.5) The estimator which satisfies these properties is a minimum variance, linear and unbiased estimator, and is known as the kriging estimator. The corresponding error of estimation is the kriging error. This estimator is also known as the BLUE (for Best Linear Unbiased Estimator) estimator. This was named by Matheron in acknowledgement of the early work of Krige's in the optimization of the evaluation of the South African gold mines. The following notations will be used: µK kriging estimator. o2k = o2K (w,, to W) kriging error.]

Jan 1, 1978

1. Book reviews A report by the Monopolies and Mergers Commission on the efficiency and. costs in the development, production and supply of coal by the NCB (Chairman G. Le Quesne). London, Her Majesty's Stationery Office, Jun. 1983. £20 for report and appendices (2 vols). Reviewer: M. J. Martinson Canadian mines handbook 1983-84, edited by M. R. Brown. Toronto, Northern Miner Press Ltd, 1983. 444 pp. $22. Reviewer: Northern Miner Review Editor 2. New publications Developments in geophysical exploration methods-5, edited by A. A. Fitch. Barking. Applied Science Publishers Ltd (Ripple Road, Barking, Essex IG II OSA, England), 1983. 255 pp. £35.75. High-pressure researches in geoscience--behaviour and properties of earth materials at high pressures and temperatures, edited by W. Schreyer. Stuttgart, E. Schweizerbart'sche Verlagsbuchhandlung, 1983. 545 pp. DM 188. Dynamics of oil and gas accumulations, by Alain Perrodon. Pau, Elf Aquitaine (Documentation Centre Micoulau, 64018 Pau, France), 1983. 368 pp. 240 FF. New paths to mineral exploration, edited by F. Bender. Stuttgart, E. Schweizerbart'sche Verlagsbuchhandlung, 1983. 169 pp. DM 58. Results of the First Workshop on Standards in Geothermics, edited by R. Haenel and M. Gupta. Stuttgart, E. Schweizerbart'sche Verlagsbuchhandlung, 1983. DM 98. E&MJ book of jlowsheets edited by Paul C. Merritt. New York, McGraw-Hill, 1983. 214 pp. $42. 1983 E&MJ international directory of mining. New York, McGraw-Hill, 1983. 808 pp. $70. The future of heavy crude and tar sands - volume 11. New York, McGraw-Hill, 1983. 1300 pp. $1l0. 3. Mineral Policy and Energy publications Aluminium, by A. Johnston. 12 pp. . Arsenic, by J. J. Hogan. 4 pp. Cobalt, by D. G. Fong. 6 pp. Selenium and tellurium, by A. G. Johnston. 7 pp. Stone, by D. H. Stonehouse. 13 pp. Uranium, by R. T. Whillans. 16 pp. 4. Mintek publications Report M88 'l'he recovery of platinum-group metals and gold by the lead-collectionstep of thefire-assay procedure. Report MI04 The preparation and analysis of reference materials, and the provision of recommended values. Progress report no. 5. Report Mll1 The determination, by flow-injection analysis, of iron, sulphate, silver, and cadmium. Special publication 3 A guide to the presentation of papers.

Jan 1, 1983

By Ian MacKenzie

Over the past twelve years, professionals such as architects, engineers, accountants, and attorneys have not had to pay a great deal of attention to GST. The fees charged to clients (outputs) have not been subject to GST, but they have had to pay GST on al purchases of materials and taxable services relating to their activities.

Jan 1, 1990

By D. F. Malan, U. Du Preez, P. S. Heyns

South Africa has two main platinum reef deposits, namely the Merensky reef and the UG2 reef. These reefs are currently mined using traditional drilling and blasting methods. Mechanized cutting could potentially enable continuous mining, which would offer significant advantages. This would require thorough understanding of the cutability of the rock. To explore this, a linear cutting machine was developed to conduct laboratory scale cutting tests. This work describes the development and commissioning of the cutting machine using sandstone, as well as subsequent characterization tests on UG2 reef samples. UG2 reef has large variability in strength on a millimeter scale. This introduces uncertainty in the test results due to added variance from one cut to the next for the same UG2 reef sample. Another problem is the variability in rock properties of the UG2 reef, when testing samples from different mines. The cutting tests led to fine fragmentation, which is known to be a significant problem for cleaning operations in underground stopes and warrants further research. A finite element method simulation of the rock cutting was conducted using ANSYS LS-DYNA and the continuous surface cap model to simulate rock cutting in the UG2 reef. It was found that it is possible to use LS-DYNA with the continuous surface cap model to model rock cutting of UG2 reef and get acceptable results, but the user must calibrate the model parameters using the experimental results. Therefore, the model is only fit for one set of cutting parameters and further work is required to generalize results.

Nov 27, 2024

By M. Royle, A. Bloem, R. Uken

Rock mass damage induced by mining increases the fracture frequency and joint aperture width in the pit walls and rock mass behind open pit mine slopes. The depth and intensity of this mechanical damage relative to the pre-mining state is not well understood and yet is a major factor in the development of slope stability models and operational guidelines. The induced damage can be partitioned into domains or zones. The blast damage zone is essentially a ‘free flow’ rock mass volume, which transitions quite rapidly into the excavation damage zone, which extends beyond that. In both zones, transient high in situ water pressures are often linked to unstable slope conditions. Whereas rock damage can enhance passive depressurisation in the rock mass, high infiltration rates on the other hand, as one could expect during rainstorm events, will decrease slope stability within the dilated pit rock mass, especially in the blast damage zone-excavation damage zone, by increasing pore pressures for short periods of time. Ice jacking and freshet are additional factors to consider in (sub) arctic environments and can be exacerbated by unfavorable rock fabric orientation. On a local scale, brittle deformation damage zones, in the form of faults, can contribute to slope instability, or enhanced stability because of slope depressurisation, depending on their location and orientation relative to the pit shape and the water sources. In this study, the shapes of the damage zones and their anticipated impact on infiltration and/or passive depressurisation are considered for different pit morphologies, rock mass conditions, in situ stress, and hydrogeological settings. Some unusual hydrological situations, like mining towards rivers and lakes and the potential effects on pore pressures, are also considered. This investigation has resulted in the development of a method to adjust initial hydraulic conductivity values used to estimate transient pore pressure conditions found in rock masses exposed in different pit morphologies and stress regimes as well as discontinuities’ orientation relative to open faces within the open pit mine. The changes in K values and pore pressures can then be used to determine hydrogeological influence more accurately on future pit slope stability.

Sep 1, 2025

By D. Almond

Low-grade, complex mineral deposits have resulted in the need for complicated large-throughput processing plants delivering increased productivity, reliability, and utilization, together with reducing operational costs. Complex mineralogy has resulted in complicated process flow sheets designed to recover minerals as efficiently as possible. In addition, the remote location of many minerals-processing plants, continuously rising energy costs, and fierce competition pose significant challenges to the modern mine, compounded by a global scarcity of qualified and experienced operational personnel. Over the last decade the Internet and automation technologies have undergone major advancements. Automation technologies, solutions, and concepts that existed, but were considered risky or unreliable prior to the year 2000, have now gained acceptance and matured. Furthermore, new technologies and different collaboration schemes have appeared, offering innovative solutions to the mining industry to address many of the challenges described. These advancements in reliable remote systems that access technology through the Internet provide significant opportunity to support mining operations, enhance process performance, provide engineering services, and proactively anticipate and execute maintenance services. This paper references a global survey of automation trends in the mining industry and the potential for an intelligent collaborative environment using automation technologies to exploit opportunities in operating the plant of the future, increasing effectiveness, and reducing operational costs. A variety of possibilities are described, including asset management solutions, remote access capabilities, performance monitoring solutions, advanced process control technologies, and the formation of an intelligent collaborative environment. A real example where this technology is used to support the operation and maintenance at a cement plant in Egypt is given to underpin the concepts described in this paper.

Jan 1, 2012

By M. J. U. T. Van Wijngaarden

SYNOPSIS The corrosion characteristics of a new steel, 14Cr, which is a modification of the well-known 3CR12, in aqueous sulphate solution were studied through polarization diagrams and a computer analysis based on the polarization¬resistance technique. It was found that the corrosion rate of 14Cr steel is independent of pH for pH values above 6, but, below a pH value of 4, the corrosion rate increases sharply with decreasing pH. In air-saturated solutions of neutral and mildly alkaline pH, the corrosion rate is approximately 60 µm per year. The 14Cr steel shows a twentyfold improvement in corrosion resistance over that of 3CR12 in sulphate solutions at pH 2,0. This is considered to be due to the beneficial effect of its higher chromium and nickel contents.

Jan 1, 1985

By S. Stone

Because of problems encountered with conventional timber supports, a system of concrete sausageshaped support pillars was tested. The pillars are 3 m long, 0,6 m wide, and between 70 and 80 cm high (the height of the stoping width). They consist of bags filled with a grout of cement (slagment and sand in the ratio of I :2, and are installed in a staggered pattern 6 m apart on dip and 2 m apart on strike. These support packs have proved successful, and, although they cost more than the timber supports formerly used (R4,63 per cent are supported as against R2,26 for the conventional timber pack), their use is felt to be justified when account is taken of the costs of lost production and low productivity due to the bad hangingwall conditions that occurred with the conventional system.

Jan 1, 1978

By A. J. Buchan

The wear of steel pipelines used for the transportation of backfill slurries is frequently regarded as an erosion problem only. An investigation was undertaken of the likely contribution to the total 'wear rate' made by corrosion. Use was made of a pipe flow loop with catholically protected specimens and corrosion inhibitors. Laboratory electrochemical tests utilizing a rotating-cylinder electrode were also conducted. The slurries used were classified tailings from two mines at a relative density of 1,7. The velocities were between 2 and 4,9 m/s. Substantial decreases in the wear rate of up to 80 per cent for one slurry and up to 67 per cent for the other were obtained with the use of corrosion control, showing that corrosion and, more importantly, interaction between erosion and corrosion, contribute a significant portion of the overall wear in steel pipelines

Jan 1, 1994

By L Tolmay, L Nair

Investor confidence can be compromised when one observes large discrepancies between the SAMREC reserves and the mining plan. It is therefore up to the responsible persons to ensure that all contributing factors get taken into account when determining a reserve declaration. Confounding factors could be further aggravated by large oscillations in the commodity price thus resulting in major changes to the mining plan, if the accepted price was either too optimistic or pessimistic. Additional factors that must receive our attention are, uncertainty in geological facies type, mining practices, geology and grade estimation. The paper outlines (in the authors? opinion) some of the important factors that need to be taken into account, in order to ensure proper alignment between the estimates of the life of mine (LOM) reserve grades, and the corresponding actualisation of the mining plan. These parameters provide an historical insight into what actually happens when attempts are made to implement the mining envisaged in the LOM plan. In turn these allow judicious application of discount factors that enable a realistic estimate of SAMREC reserve classification and declaration. Some of the factors that will be covered are: - 1) Flexibility of developed reserves and the ability to maintain this. 2) Mining control mechanisms and their overall efficacy. 3) The ability to extrapolate facies types and its effect on grade control. 4) The ability to control the mining mix and value variation. 5) Finding a happy medium between optimism and pragmatism.

Jan 1, 2007

By T. Z. Mugodi, D. R. Fleming

Information and Communications Technology (ICT) is defined as ‘The goods and services that support the electronic display, processing, storage and transmission of information’. Early in 2002 the South African Department of Trade and Industry (DTI) commissioned a study into the diffusion and adoption of ICT in eight sectors of the economy. The platinum mining Sector was one of these. The key findings presented in this paper are based on the platinum sector component of that study. The paper examines the theoretical basis behind technology transfer and innovation diffusion and presents the results of an ICT diffusion survey carried out in the South African platinum mining sector. ICT is shown as the modern day technological tool which is an accelerator of economic development. The current state of ICT diffusion in the platinum mining sector is defined and projections for the near future are given. Recommendations which will ensure smooth and full adoption are presented and justified.

Jan 1, 2003

By M. Kerr

Background- History The most significant change in mining since the late 1970?s has been the emergence of very large scale mining operations , which have been developed to ensure profitability with relatively low grade ores. These large tonnage operations have resulted in the development of larger unit sized machines in all operations of beneficiation, solid-liquid separation and dewatering. Often only a few flotation lines are installed and tonnages up to 25 ktpd and beyond are not uncommon. The increased throughputs have led to the development of circular, reactor type tank designs. The reactor cell system is the most up to date flotation cell design to utilise the principles of circular cell design. The Svedala DV mechanism was specially developed to suit the RCS machine giving good solids handling characteristics and excellent metallurgical performance. Development of UG2 ore type flotation equipment The equipment was developed and optimised by Svedala process from 1995. A higher energy specification was requested by industry. This amounted to 3kW/m3 for installed volume. Existing designs were at 1.5kW/m3. Hence various modifications were required to achieve the required power input. The first 50m3 machines were installed and developed at Impala Platinum?s UG2 circuit over a one year period. Once reliability and performance was achieved, over 300 large volume flotation cells were installed at Anglo Platinum and Lonmin operations as well. Pilot Plant Development The Impala Platinum High Energy pilot plant was commissioned in 2002 and had an installed power exceeding 5kW/m3. It was operated for over a year at the tailings dam booster station and was fundamental to the large scale scavenging plant design. All experience in overcoming mechanical and operational problems was applied in scale up design principles. A very robust mechanism was designed to accommodate the additional power input from installed motors, as well as the high SG (>1.5) of the feed source. The pilot plant flowsheet is shown in the figure below.

Jan 1, 2007

By A. Kazemi, M. A. Ahmadi

Pressure tunnels are constructed nurously in related with powerhouse. In some cases, according to high internal water pressure, rock mass around tunnel can seldom suffer this pressure. So installation of concrete lining which interacts with rock mass and suffers parts of this pressure and transfers the rest of the pressure to the rock. In this paper hydromechanical interaction between rock and lining is investigated. With using empirical and numerical methods concrete lining for Symareh waterway is designed. Initial support of 10 cm reinforced shotcret with wire mesh and rock bolts pattern of 2.5*2.5 m with length of 4 m is suggested. By using FLAC package final lining with paying attention to axial force and momentum in reinforced concrete was designed. Reinforced concrete with 60 cm thickness and two rows of bars, 18 mm diameter and 20 cm spacing are designed. Also for preventing cracks in concrete which caused by the change of temperature and shrinkage, bars with 10 mm diameter and 25 cm spacing, and also bars with 8 mm diameter and 10 cm as minimum shear bars are suggested. Plusieurs galeries en pression se construisent en liaison avec les centrales électriques. Dans certaines galeries, suite à une haute pression interne de l'eau, le massif rocheux autour de la galerie ne peut pas supporter cette pression. L'installation d'une couche de béton a l'intérieur de la galerie donc réagit avec les roches et support d'une partie de cette pression et transfère le reste de la pression aux roches. Dans ce papier, l'interaction hydromécanique entre la roche et la couche en béton a été étudiée. En se basant sur les méthodes empiriques et numériques le système de support de galerie de passage d'eau de Saymareh a été conçu. Un soutènement initial d'une épaisseur de 10 cm de béton étant renforcé par un grill métallique et une maille de boulon (2.5 * 2.5 m) d'une longueur de 4 m a été proposé. En utilisant le logiciel de FlAC, la couche finale en béton selon les forces dans le béton a été conçue. Le béton renforcé d'une épaisseur de 60 cm et deux ranges d'armateurs (18 mm de diamètre) avec un intervalle de 20 cm a été conçu. De plus; pour éviter des fissures dans le béton suite au changement de la température et de l'extraction, des armateurs de 10 mm de diamètre et de 25 cm d'intervalle pour augmenter la résistance au sciesiement du béton ont été proposes Unter Druck stehende Tunnels werden hauptsaechlich im Zusammenhang mit Kraftwerken gebaut. In einigen Faellen, wo der Wasserdruck zu hoch ist, Kann selten die Felsenmasse diesen hoehen Druck allein aufnehwen. Deshalb werden sie mit Betonauskleidung versehen, die wegen guter Wechelwirkung mit der Felsenmasse einen Hauptanteil des Druckes aufnehmen Kann, wobei der Rest an die Felsenmesse weitergeleitet wird. In dieser Arbeit wird die hydromechanische Wechelwirkung zwischen der Gesteinmasse und der Auskleidung untersucht. Mit Hilfe empirischen und numerischen Verfahren sowie Kombination der beiden wurde eine Betonauskleidung fuer die Symareh Wasser Kannal koustruiert. Als erstes wurde ein 10Cm dicker armierter Beton mit einem Mashengitter von 2.5*2.5 sowie den gleichen Felsbolzenabstaenden und einer Laenge von 4 m vorgeschlagen. Mit Hilfe des FLAC Programms wurde die Hauptauskleidung unter Beruecksichtigung von Axialkraeften und Momenten im Stahlbeton koustruiert. Der 60 Cm dicke Stahlbeton wurde mit zwei Reihen von Stangen, 8 mm im Durchmesser und in Abstaenden von 20 Cm koustruiert. Ferner im Sinne der Vorbeugung gegen Rissen im Beton, die durch Temperatur aendeungen und Schrumpfungen bedingt sind, wurden Stangen mit 10 mm Durchmesser und 2.5 Cm Abstaenden zur Erhoehung vor Scherfestigkeit des Betons vorgeschlagen.

Jan 1, 2003

By I. V. Filippova, Y. Foucaud, M. Badawi, L. O. Filippov, S. Lebègue

To optimize the flotation of Ca-minerals, their separation contrasts were investigated by coupling experimental and theoretical techniques. We showed that they mainly rely on structural properties such as the Ca-Ca distance on their exposed surfaces but also on the ability to control the intermolecular interactions. An optimized composition of the carboxylic collector by calculating the collector-mineral and the intermolecular interactions was developed. Blending the saturated acids and non-ionic molecules with a fatty acid collector significantly increases the flotation selectivity between scheelite (CaWO4) and fluorite (CaF2). The theoretical results were validated by experimentally improving the separation contrast between Ca-minerals. After the tests of several depressants and collectors, the best depression of gangue Ca-minerals (fluorite, apatite and vezuvianite) was found by combining sodium silicate and sodium carbonate. Keywords: Ca Minerals, Fluorite, Scheelite, Carboxylic acids, Unsaturated Acid, Fatty acids

Jan 1, 2020

By Yuandong Qiao, Erdong Li, Chao Lv, Junjian Ye

The gas-based CO reduction of Panzhihua vanadium titanomagnetite concentrate from 1100°C- 1250°C was investigated in this paper. The reduction degree increased with increasing temperature and increasing reduction time. At a temperature of 1250°C and a reduction time of 20 minutes, the metallisation degree reached 92%. The iron-titanium oxide phase transformation during reduction process was Fe2.75Ti0.25O5→Fe2.5Ti0.5O4→FeTiO3→FeTi2O5 according to the X-ray diffraction analysis. The SEM and map scan by energy spectrum of results of reduced samples at different temperatures indicated that the metallic iron particle size increased gradually as the reduction temperature increased. These results can serve as a reference for the reduction of vanadium titanomagnetite by CO. Keywords: Vanadium titanomagnetite concentrate, CO reduction, phase transformation, reaction mechanism

Jan 1, 2020

By C. Chapman, M. G. Reading, M. P. Amsden

Ecstall Mining Limited, a subsidiary of Texas Gulf Sulphur Company, operates the Kidd Creek Mine, a 10000 tons per day base metal producer, near Timmins, Ontario. Two different types of ore are mined and milled: copper-zinc and silver-lead-zinc. At the highly automated Ecstall concentrator the ores are processed by selective flotation in three individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous on-stream X-ray analysis. Recently this system was automated further by the addition of computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery by 1.1 per cent, zinc recovery by 1.4 per cent, and have reduced reagent costs by 16 per cent. Although not expected, copper and zinc concentrate grades were improved slightly as well.

Jan 1, 2014

By J. H. van Dalen, P. J. Brandt, F. W. Wessels

A maximum of ten process streams (Merrill barren solutions) can be monitored sequentially with this on-line analyser, and gold concentrations as Iow as 0,005 mg/I can be determined. The design is a further development of the Tell-tale analyser constructed by the Corner House Laboratories during the period 1965-69. The barren solution is preconcentrated automatically by solvent extraction, the solvent being a solution of I per cent Aliquat 336 in di-isobutyl ketone. An aqueous-to-solvent ratio of 40: I is maintained. The extracted gold in the organic phase is determined by flame atomic absorption, each analysis taking approximately II minutes. The long-term reproducibility of the absorbance readings over a 24-hour period of repetitive sampling of four simulated process streams varied from 6,9 to 4,1 per cent relative standard deviation for gold concentrations of 0,0 I to 0,05 mg/I.

Jan 1, 1980

The following diagrams should replace the Figs. 4, 5, and 6 that appeared on pages 412 and 413 of the October 1986 issue. These relate to the paper entitled' A new method for the rapid float-sink analysis of coal fines' by J-P. Franzidis and M.C. Harris Womanpower In 1981 the Publicity Committee of the Federation of Societies of Professional Engineers (FSPE) decided that one way in which the engineering manpower pool could be increased would be by the introduction of womanpower to the profession. Since then, Std 9 and 10 girls have been invited to attend the engineering winterschools held annually at the various universities under the auspices of SAFUES. Coal-mining wastes The 2nd International Symposium on the Reclamation, Treatment and Utilization of Coal Mining Wastes will be held in Nottingham (England) from 7th to 11th September, 1987.

Jan 1, 1986

By P. A. J. Cabassi, B. K. Loveday, M. J. Wilkinson, P. H. Radcliffe

The recovery of gold, uranium, and pyrite from accumulated residues at mines in the Orange Free State is adversely affected by the presence of pyrophyllite, which is naturally floatable and must be prevented from floating with the desired constituents by the use of a mica depressant, and of thucholite (uraniferous kerogen), which contains significant quantities of uranium and gold but does not float readily in the presence of a mica depressant. In laboratory tests on these residues, the use of a mixture of MIBC (methyl isobutyl carbinol) and paraffin in addition to the suite of reagents normally used was found to increase the gold recovery substantially, but the sulphur grade was lower. The recovery of thucholite also increased considerably, but the proportion of uranium associated with this mineral was small. Plant trials, which are continuing, have been encouraging, indicating an increase in the gold recovery of 4,6 per cent.

Jan 1, 1983